Synthesis and electrochemical properties of Li4Ti5O12/C composite by the PVB rheological phase method

Spinel Li₄Ti₅O₁₂/C powders were synthesized successfully by a simple rheological phase method using polyvinylbutyral (PVB) as both template and carbon source. The structure and morphology characteristics of the composite were investigated by X-ray diffraction (XRD), field emission scanning electron microscopy and transmission electron microscopy. The XRD results showed that the composite had a good crystallinity. Its average particle size was about 2.1 μm with a narrow size distribution as a result of homogeneous mixing of the precursors. The in situ carbon coating produced by decomposition of PVB played an important role in improving electrical conductivity, thereby enhancing the rate capacity of Li₄Ti₅O₁₂ as anode material in Li-ion batteries. The Li₄Ti₅O₁₂/C composite, synthesized at 800 °C for 15 h under argon, containing 0.98 wt% of carbon, exhibited better electrochemical properties in comparison with the pristine Li₄Ti₅O₁₂, which could be attributed to the enhanced electrical conductive network of the carbon coating on the particle surface.     

Characteristics of spherical-shaped Li4Ti5O12 anode powders prepared by spray pyrolysis

Spherical-shaped Li₄Ti₅O₁₂ anode powders with a mean size of 1.5 μm were prepared by spray pyrolysis. The precursor powders obtained by spray pyrolysis had no peaks of crystal structure of Li₄Ti₅O₁₂. The powders post-treated at temperatures of 800 and 900 °C had the single phase of spinel Li₄Ti₅O₁₂. The powders post-treated at a temperature of 1000 °C had main peaks of the Li₄Ti₅O₁₂ phase and small impurity peaks of Li₂Ti₃O₇. The spherical shape of the precursor powders was maintained after post-treatment at temperatures below 800 °C. The Brunauer-Emmett-Teller (BET) surface areas of the Li₄Ti₅O₁₂ anode powders post-treated at temperatures of 700, 800 and 900 °C were 4.9, 1.6 and 1.5 m²/g, respectively. The initial discharge capacities of Li₄Ti₅O₁₂ powders were changed from 108 to 175 mAh/g when the post-treatment temperatures were changed from 700 to 1000 °C. The maximum initial discharge capacity of the Li₄Ti₅O₁₂ powders was obtained at a post-treatment temperature of 800 °C, which had good cycle properties below current densities of 0.7 C.     

Electrical and electrochemical properties of molten salt-synthesized Li4Ti5−xSnxO12 (x=0.0, 0.05 and 0.1) as anodes for Li-ion batteries

Submicron-sized polyhedral Li₄Ti_5−xSn_xO₁₂ (x=0.0, 0.05, and 0.1) materials were successfully prepared by a single-step molten salt method. The structural, morphological, transport and electrochemical properties of the Li₄Ti_5−xSn_xO₁₂ were studied. X-ray diffraction patterns showed the formation of a cubic structure with a lattice constant of 8.31 Å, and the addition of dopants follows Vegard's law. Furthermore, FT-IR spectra revealed symmetric stretching vibrations of octahedral groups of MO₆ lattice in Li₄Ti₅O₁₂. The formation of polyhedral submicron Li₄Ti_5−xSn_xO₁₂ particles was inferred from FE-SEM images, and a particle size reduction was observed for Sn-doped Li₄Ti₅O₁₂. The chemical composition of Ti, O and Sn was verified by EDAX. The DC electrical conductivity was found to increase with increasing temperature, and a maximum conductivity of 8.96×10⁻⁶ S cm⁻¹ was observed at 200 °C for Li₄Ti₅O₁₂. The galvanostatic charge–discharge behavior indicates that the Sn-doped Li₄Ti₅O₁₂ could be used as an anode for Li-ion batteries due to its enhanced electrochemical properties.     

Synthesis and electrochemical performances of Li4Ti4.95Al0.05O12/C as anode material for lithium-ion batteries

Spinel compounds Li₄Ti_5−xAl_xO₁₂/C (x=0, 0.05) were synthesized via solid state reaction in an Ar atmosphere, and the electrochemical properties were investigated by means of electronic conductivity, cyclic voltammetry, and charge-discharge tests at different discharge voltage ranges (0-2.5 V and 1-2.5 V). The results indicated that Al³⁺ doping of the compound did not affect the spinel structure but considerably improved the initial capacity and cycling performance, implying the spinel structure of Li₄Ti₅O₁₂ was more stable when Ti⁴⁺ was substituted by Al³⁺, and Al³⁺ doping was beneficial to the reversible intercalation and deintercalation of Li⁺. Al³⁺ doping improved the reversible capacity and cycling performance effectively especially when it was discharged to 0 V.     

Electrochemical behavior of Li intercalation processes into a Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 cathode

Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (X=0.17, 0.25, 0.33, 0.5) compounds are prepared by a simple combustion method. The Rietvelt analysis shows that these compounds could be classified as having the α-NaFeO₂ structure. The initial charge-discharge and irreversible capacity increases with the decrease of x in Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂. Indeed, Li[Ni_0.50Mn_0.50]O₂ compound shows relatively low initial discharge capacity of 200 mAh/g and large capacity loss during cycling, with Li[Ni_0.17Li_0.22Mn_0.61]O₂ and Li[Ni_0.25Li_0.17Mn₀.₅₈]O₂ compounds exhibit high initial discharge capacity over 245 mAh/g and stable cycle performance in the voltage range of 4.8 -2.0 V. On the other hand, XANES analysis shows that the oxidation state of Ni ion reversibly changes between Ni²⁺ and about Ni³⁺, while the oxidation state of Mn ion sustains Mn⁴⁺ during charge-discharge process. This result does not agree with the previously reported ‘electrochemistry model’ of Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂, in which Ni ion changes between Ni²⁺ and NI⁴⁺. Based on these results, we modified oxidation-state change of Mn and Ni ion during charge-discharge process.     

Characterization of sprayed and sputtered thin films for lithium ion microbatteries

We have investigated the preparation of thin films of anode and cathode materials for all oxide solid state lithium ion microbatteries. Thin films of LiCoO₂ and Li_4/3Ti_5/3O₄ have been deposited by both spray pyrolysis and RF magnetron sputtering. The structural and electrochemical properties of high temperature-LiCoO₂ thin films have been determined. Spray pyrolysis prepared higher quality LiCoO₂ thin films. Both sprayed and sputtered Li_4/3Ti_5/3O₄ thin films exhibited interesting lithium intercalation capacity. However, it has been demonstrated that RF magnetron sputtering is more efficient than spray pyrolysis for optimizing the interface between Li_4/3Ti_5/3O₄ and the substrate material. Paper presented at the 3rd Euroconference on Solid State Ionics, Teulada, Sardinia, Italy, Sept. 15–22, 1996     

Effect of ultrasonic irradiation on structure and electrochemical properties of LiMn2O4 thin films cathode material for Li-ion micro-batteries

Two kinds of spinel LiMn₂O₄ thin film for lithium ion micro-batteries were successfully prepared on polycrystal Pt substrates by spin coating methods, which were carried out under ultrasonic irradiation (USG) and magnetic stirring (MSG), respectively. The microstructures and electrochemical performance of LiMn₂O₄ thin films were characterized by thermogravimetry analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM), and galvanostatic charge-discharge measurements. It was found that the crystalline structure of USG samples grew better than that of the MSG samples. At the same time, higher discharge capacity and better cycle stability were obtained for the LiMn₂O₄ thin films of USG at the current density of 50 μAh/cm² between 3.0 and 4.3 V. The 1st discharge capacity was 57.8 μAh/cm²-μm for USG thin films and 51.7 μAh/cm²-μm for MSG thin films. After 50 cycles, 91.4% and 69% of discharge capacity could be retained respectively, indicating that ultrasonic irradiation condition during spin coating was more suitable for preparing spinel LiMn₂O₄ thin films with better electrode performance for lithium ion micro-batteries.     

Recent development and application of Li4Ti5O12 as anode material of lithium ion battery

Lithium-ion batteries with both high power and high energy density are one of the promising power sources for electric devices, especially for electric vehicles (EV) and other portable electric devices. One of the challenges is to improve the safety and electrochemical performance of lithium ion batteries anode materials. Li₄Ti₅O₁₂ has been accepted as a novel anode material of power lithium ion battery instead of carbon because it can release lithium ions repeatedly for recharging and quickly for high current. However, Li₄Ti₅O₁₂ has an insulating character due to the electronic structure characterized by empty Ti 3d-states, and this might result in the insufficient applications of LTO at high current discharge rate before any materials modifications. This review focuses first on the present status of Li₄Ti₅O₁₂ including the synthesized method, doping, surface modification, application and theoretical calculation, then on its near future development.     

X-RAY PHOTOELECTRON SPECTROSCOPY STUDY ON ELECTROCHROMIC V2O5 THIN FILM

Nanocrystalline V₂O₅ thin films were reactively radio-frequency magnetron-sputtered under optimal deposition parameters. Their electrochemical and electrochromic characteristics were investigated by cyclic voltammetry and in-situ monochromatic transmittance measurements. Upon lithium intercalation, V₂O₅ thin films showed a double electrochromic behavior depending on the wavelength and the intercalation extent. X-ray photoelectron spectroscopy results showed that part of the V⁵⁺ in V₂O₅ was reduced to V⁴⁺ during the Li⁺ intercalation process.     

Electrochemical behaviour of sputtered c-V2O5 and LiCoO2 thin films for solid state lithium microbatteries

Here are reported for the first time electrochemical data on all-solid-state lithium microbatteries using crystalline sputtered V₂O₅ thin films as cathode materials and LiPON as solid electrolyte. The stable specific capacity of 30 µAh/cm² found with a 2.4 µm thick film competes very well with the best values obtained for solid state microbatteries using amorphous films. With the challenge of decreasing the temperature of heat treatment for sputtered LiCoO₂ thin films, we show that a temperature of 500 °C combined with an optimized bias sputtering (-50 V) allows to get highly crystalline deposits, to minimize the presence of Co₃O₄ and to suppress any trace of the cubic phase. At the same time the theoretical specific capacity is reached in the 4.2 V-3 V range and a good cycling behaviour is achieved with a high capacity of 50 µAh/cm²/µm after 140 cycles at 10 µA.cm².     

糠醇辅助的聚合凝胶法制备纳米Li4Ti5O12负极材料

以硝酸锂、钛酸正丁酯和糠醇为反应物,采用糠醇聚合凝胶法制备了纳米Li₄Ti₅O₁₂粉体．利用XRD、SEM和BET比表面测试对产物进行了表征,并研究了纳米Li₄Ti₅O₁₂粉体作为锂离子电池负极材料的电化学性能．在700℃或更高温度烧结时产物为纯相的尖晶石型．通过柠檬酸、聚乙烯吡咯烷酮、十六烷基三甲基溴化铵(CTAB)表面活性剂的加入能够减少产物颗粒的团聚程度,增大粉体的比表面积,提高其电化学性能．加入0.5 g CTAB、700℃烧结12 h的Li₄Ti₅O₁₂粉体展示出最高的比容量和最佳的循环性能,10 C下充电比容量高达156.7 mAh/g．     

Electrical behavior of BaZr0.1Ti0.9O3 and BaZr0.2Ti0.8O3 thin films

BaZr_0.1Ti_0.9O₃ and BaZr_0.2Ti_0.8O₃ (BZT) thin films were deposited on Pt/Ti/LaAlO₃ (1 0 0) substrates by radio-frequency magnetron sputtering, respectively. The films were further annealed at 800 °C for 30 min in oxygen. X-ray diffraction θ-2θ and Φ-scans showed that BaZr_0.1Ti_0.9O₃ films displayed a highly (h 0 0) preferred orientation and a good cube-on-cube epitaxial growth on the LaAlO₃ (1 0 0) substrate, while there are no obvious preferential orientation in BaZr_0.2Ti_0.8O₃ thin films. The BaZr_0.1Ti_0.9O₃ films possess larger grain size, higher dielectric constant, larger tunability, larger remanent polarization and coercive electric field than that of BaZr_0.2Ti_0.8O₃ films. Whereas, BaZr_0.1Ti_0.9O₃ films have larger dielectric losses and leakage current density. The results suggest that Zr⁴⁺ ion can decrease dielectric constant and restrain non-linearity. Moreover, the enhancement in dielectric properties of BaZr_0.1Ti_0.9O₃ films may be attributed to (1 0 0) preferred orientation.     

Synthesis and characterization of lithium manganese oxides with core-shell Li4Mn5O12@Li2MnO3 structure as lithium battery electrode materials

By a facile LiNO₃ flux method, lithium manganese oxide composites (xLi₄Mn₅O₁₂? yLi₂MnO₃) were synthesized using a hierarchical organization precursor of manganese dioxide. Li₄Mn₅O₁₂ and Li₂MnO₃ have spinel and rocksalt structures, respectively. The lithiation and structural transformation from the precursor to the composites occurred topotactically from exterior toward interior in the precursor particle with the increase of reaction time, and the composites had core-shell spinel@rocksalt structures in addition to the original hierarchical core-shell organization. The electrochemical measurements at 50 °C after 50 cycles confirmed that a typical spinel@rocksalt cathode had higher capacity retention (87.1%) than that with the composition close to the stoichiometric spinel (64.6%), indicating the Li₂MnO₃ shell can improve cycling stability for the composite electrode at elevated temperature.     

Influence of the substrate material on the properties of pulsed laser deposited thin Li1+xMn2O4−δ films

Thin Li_1+xMn₂O_4−δ films were deposited on several substrate materials (stainless steel, p-doped silicon and glassy carbon) by pulsed laser deposition. To obtain the correct thin film stoichiometries, targets with a different amount of excess lithium were required (Li_1.03Mn₂O₄ + xLi₂O; x = 2.5 and 7.5 mol%). The resulting polycrystalline thin films were characterized with respect to their morphology and electrochemical activity. It was found that only thin Li_1+xMn₂O_4−δ films deposited on stainless steel and glassy carbon showed the typical insertion and deinsertion peaks of Li⁺ during cycling.     

Effects of vanadium doping on structure and electrical properties of SrBi4Ti4O15 thin films

The effects of vanadium(V) doping into SrBi₄Ti₄O₁₅ (SBTi) thin films on the structure, ferroelectric, leakage current, dielectric, and fatigue properties have been studied. X-ray diffraction result showed that the crystal structure of the SBTi thin films with and without vanadium is the same. Enhanced ferroelectricity was observed in the V-doped SrBi₄Ti₄O₁₅ (SrBi_4−x/3Ti_4−xV_xO₁₅, SBTiV-x (x = 0.03, 0.06, and 0.09)) thin films compared to the pure SrBi₄Ti₄O₁₅ thin film. The values of remnant polarization (2P_r) and coercive field (2E_c) of the SBTiV-0.09 thin film capacitor were 40.9 μC/cm² and 105.6 kV/cm at an applied electric field of 187.5 kV/cm, respectively. The 2P_r value is over five times larger than that of the pure SBTi thin film capacitor. At 100 kHz, the values of dielectric constant and dielectric loss were 449 and 0.04, and 214 and 0.06 for the SBTiV-0.09 and the pure SBTi thin film capacitors, respectively. The leakage current density of the SBTiV-0.09 thin film capacitor measured at 100 kV/cm was 6.8 × 10⁻⁹ A/cm², which is more than two and a half orders of magnitude lower than that of the pure SBTi thin film capacitor. Furthermore, the SBTiV-0.09 thin film exhibited good fatigue endurance up to 10¹⁰ switching cycles. The improved electrical properties may be related to the reduction of internal defects such as bismuth and oxygen vacancies with changes in the grain size by doping of vanadium into SBTi.     

Li4Ti5O12/Ag composite as electrode materials for lithium-ion battery

The Li₄Ti₅O₁₂/Ag composites were prepared by thermal decomposition of AgNO₃ added to Li₄Ti₅O₁₂ powders. The influence of the Ag contents and the mixing media on the particle size, morphology and electrochemical performance of Li₄Ti₅O₁₂/Ag composites were investigated. The highest discharge capacity of the Li₄Ti₅O₁₂/Ag composite reached at the 5 wt.% of Ag content. Compared with alcohol medium, distilled water as mixing medium presented the Li₄Ti₅O₁₂/Ag composite with higher specific capacity and better cycling performance, leading to a reversible capacity after 50 cycles of 184.2 mAh/g with a capacity degradation of 3.31% compared to the second cycle at 2 C rate.     

Preparation and characterization of spinel Li4Ti5O12 nanoparticles anode materials for lithium ion battery

Spinel Li₄Ti₅O₁₂ nanoparticles were prepared via a high-temperature solid-state reaction by adding the prepared cellulose to an aqueous dispersion of lithium salts and titanium dioxide. The precursors of Li₄Ti₅O₁₂ were characterized by thermogravimetry and differential scanning calorimetry. The obtained Li₄Ti₅O₁₂ nanoparticles were characterized using X-ray diffraction, transmission electron microscopy (TEM) and electrochemical measurements. The TEM revealed that the Li₄Ti₅O₁₂ prepared with cellulose is composed of nanoparticles with an average particle diameter of 20–30 nm. Galvanostatic battery testing showed that nano-sized Li₄Ti₅O₁₂ exhibit better electrochemical properties than submicro-sized Li₄Ti₅O₁₂ do especially at high current rates, which can deliver a reversible discharge capacity of 131 mAh g⁻¹ at the rate of 10 C, whereas that of the submicro-sized sample decreases to 25 mAh g⁻¹ at the same rate (10 C). Its reversible capacity is maintained at ~172.2 mAh g⁻¹ with the voltage range 1.0–3.0 V (vs. Li) at the current rate of 0.5 C for over 80 cycles.     

Structural and electrochemical study on Li(Li1/3Ti5/3)O4 anode material for lithium ion batteries

Chemical and electrochemical studies have shown that various titanium oxides can incorporate lithium in different ratios. Other compounds with a spinel-type structure and corresponding to the spinel oxides LiTi₂O₄ and Li₄Ti₅O₁₂ have been evaluated in rechargeable lithium cells with promising features. The spinel Li[Li_1/3Ti_5/3]O₄ [1–5] compound is a very appealing electrode material for lithium ion batteries. The lithium insertion-deinsertion process occurs with a minimal variation of the cubic unit cell and this assures high stability which may reflect into long cyclability. In addition, the diffusion coefficient of lithium is of the order of 10⁻⁸ cm²s⁻¹ [5] and this suggests fast kinetics which may reflect in high power capabilities. In this work we report a study on the kinetics and the structural properties of the Li[Li_1/3Ti_5/3]O₄ intercalation electrode carried out by: cyclic voltammetry, galvanostatic cycling and in-situ X-ray diffraction. The electrochemical characterization shows that the Li[Li_1/3Ti_5/3]O₄ electrode cycles around 1.56 V vs. Li with a capacity of the order of 130 mAhg⁻¹ which approaches the maximum value of 175 mAhg⁻¹ corresponding to the insertion of 1 equivalent per formula unit. The delivered capacity remains constant for hundred cycles confirming the stability of the host structure upon the repeated Li insertion-deinsertion process. This high structural stability has been confirmed by in situ Energy Dispersion X-ray analysis. Paper presented at the 7th Euroconference on Ionics, Calcatoggio, Corsica, France, Oct. 1–7, 2000.     

Ab initio studies on n-type and p-type Li4Ti5O12

This paper studies the structure and electronic properties of Li4Ti5O12, as anode material for lithium ion batteries, from first principles calculations. The results suggest that there are two kinds of unit cell of Li4Ti5O12: n-type and p-type. The two unit cells have different structures and electronic properties:the n-type with two 16d site Li ions is metallic by electron, while the p-type with three 16d Li ions is metallic by hole. However, the Li4Ti5O12 is an insulator. It is very interesting that one n-type cell and two p-type cells constitute one Li4Ti5O12 supercell which is insulating. The results show that the intercalation potential obtained with a p-type unit cell with one additional electron is quite close to the experimental value of 1.5 V.     

A new composite material Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>–SnO<Subscript>2</Subscript> for lithium-ion batteries

A new Li₄Ti₅O₁₂–SnO₂ composite anode material for lithium-ion batteries has been prepared by loading SnO₂ on Li₄Ti₅O₁₂ to obtain composite material with improved electrochemical performance relative to Li₄Ti₅O₁₂ and SnO₂. The composite material was characterized by X-ray diffraction and scanning electron microscopy. The results indicated that SnO₂ particles have encapsulated on the surface of the Li₄Ti₅O₁₂ uniformly and tightly. Electrochemical results indicated that the Li₄Ti₅O₁₂–SnO₂ composite material increases the reversible capacity of Li₄Ti₅O₁₂ and has good cycling reliability. At a current rate of 0.5 mA/cm², the material delivered a discharge capacity of 236 mAh/g after 16 cycles. It suggests the existence of synergistic interaction between Li₄Ti₅O₁₂ and SnO₂ and that the capacity of the composite is not a simple weighted sum of the capacities of the individual components. In the composite material, SnO₂ can act as a bridge between the spinel particles to reduce the interparticle resistance and as a good material for the Li intercalation/deintercalation. Thus, electrochemical performance of the Li₄Ti₅O₁₂ spinel can be improved by the surface modification with SnO₂, and the stability of Li₄Ti₅O₁₂ also serves to buffer the internal stress caused by the volume changes in lithium insertion and extraction reactions.