SPE-LC/MS/MS快速测定卷烟丝中的烟草特有亚硝胺类化合物

建立了卷烟丝中烟草特有亚硝胺类化合物(TSNAs)的SPE-LC/MS/MS分析方法,可一次性对卷烟烟丝中4种TSNAs进行定量分析.该方法弥补了传统的烟丝中TSNAs分析方法样品处理步骤多,检出限高,适应范围窄等缺点.4种TSNA的回收率的范围在95.7%～99.2%之间;相对标准偏差均小于8%;方法检出限均低于1.0 ng/g.可应用于国内外各类型卷烟的分析.     

Multi-Residue Analysis of Some Polar Pesticides in Water Samples with SPE and LC–MS–MS

In the present study a multi-residue analytical method was developed for monitoring some polar pesticides such as acephate, methamidophos, carbofuran, isoproturon, dimethoate in water with SPE (solid-phase extraction) and LC–MS–MS. Acetochlor was taken as surrogate, and alachlor as internal standard. SPE with different types of columns was compared with LLE (liquid-liquid extraction). Further, the breakthrough volume for different pesticides was determined. The results showed that the selected pesticides can be determined very sensitively with LC–MS–MS. The minimum detectable quantity (MDQ) for each pesticide was about 1.0 ng. To date, SPE cartridge studies showed that the Oasis HLB cartridges were suitable for further studies. However, for Oasis HLB cartridge, different pesticide showed different breakthrough volume. The results showed that for acephate and methamidophos, the breakthrough volume was about 30 mL of water sample, much less than the breakthrough volume of other pesticides studied. Because of the higher vapor pressure and higher Henry's constant of methamidophos, dimethoate and carbofuran, much attention should be paid on their losses in the evaporation step of the experiment. This analytical method can be applied to determine pesticide contamination in environmental water samples. Revised: 12 September 2005 and 21 October 2005     

LC-MS/MS profiling for detection of endogenous steroids and prostaglandins in tissue samples

Roles of steroid hormones, and compounds that can influence their levels in cells, are of increasing interest in e.g. cancer research, partly because resistance to hormone therapies often complicates treatment. To elucidate the processes involved, the hormones and related compounds need to be accurately measured. Reversed-phase liquid chromatography with dynamic multiple reaction monitoring mass spectrometric detection in electrospray mode is capable of providing such measurements. Therefore, LC-MS/MS was developed for sensitive, selective analysis of 11 steroid hormones, cholesterol and two prostaglandins. The effects of the tissue matrix, and solid-phase extraction (SPE) sample clean-up, on the LC-MS/MS signals of the hormones were also investigated. The results show that the developed LC-MS/MS method, following SPE clean-up to reduce matrix interference, can detect selected steroids in extracts of mouse tissues. The method provides linear measurements of the steroids at concentrations up to few ng/μL, and limits of detection in the range 0.03-0.2 pg/μL (for some compounds lower than those of previously reported methods).     

Recently developed GC/MS and LC/MS methods for determining NSAIDs in water samples

Pharmaceuticals have become major targets in environmental chemistry due to their presence in aquatic environments (following incomplete removal in wastewater treatment or point-source contaminations), threat to drinking water sources and concern about their possible effects to wildlife and humans. Recently several methods have been developed for the determination of drugs and their metabolites in the lower nanogram per litre range, most of them using solid-phase extraction (SPE) or solid-phase microextraction (SPME), derivatisation and finally gas chromatography mass spectrometry (GC-MS), gas chromatography tandem mass spectrometry (GC-MS/MS) and liquid chromatography electrospray tandem mass spectrometry (LC-ES/MS/MS). Due to the elevated polarity of non-steroidal anti-inflamatory drugs (NSAIDs), analytical techniques based on either liquid chromatography coupled to mass spectrometry (LC-MS) and gas chromatography coupled to mass spectrometry (GC-MS) after a previous derivatisation step are essential. The most advanced aspects of current GC-MS, GC-MS/MS and LC-MS/MS methodologies for NSAID analysis are presented.     

Validation and application of a novel LC/MS/MS method for the determination of isoginkgetin in rat plasma

Isoginkgetin is a biflavonoid compound isolated from the leaf extracts of Ginkgo biloba. In this study, an liquid chromatography–tandem mass spectrometry (LC/MS/MS) with liquid–liquid extraction was developed and validated for the analysis of isoginkgetin in rat plasma. In the process of chromatographic separation, selected reaction monitoring transitions for isoginkgetin and IS were m/z 566.8 → 134.7 and m/z 430.8 → 269.3, respectively. The validation parameters including selectivity, linearity, LLOQ, accuracy, precision, matrix effect, stability and recovery were satisfactory. The intra‐ and inter‐batch precision (RSD) were <12.1% in plasma, while the accuracy (RE) was within ±14.3%. This method was employed in a pharmacokinetic study on rats after the intravenous administration of isoginkgetin.     

Validation of a sensitive LC/MS/MS method for the determination of zidovudine and lamivudine in human plasma

A sensitive LC/MS/MS assay for determining zidovudine (ZDV) and lamivudine (3TC) in human plasma was validated to support antiretroviral pharmacology research programs. After addition of stable labeled isotopic zidovudine (ZDV‐IS) and lamivudine (3TC‐IS) as internal standard, a solid‐phase extraction was performed with an Oasis HLB 1 cm³ cartridge, with recoveries of 92.3% for ZDV and 93.9% for 3TC. A Phenomonex Synergi Hydro‐RP (2.0 × 150 mm) reversed‐phase analytical column was utilized for chromatographic separation. The mobile phase consisted of an aqueous solution of 15% acetonitrile and 0.1% acetic acid. Detection was accomplished by ESI/MS/MS in the positive ion mode, monitoring 268/127, 271/130, 230/112 and 233/115 transitions, for ZDV, ZDV‐IS, 3TC and 3TC‐IS, respectively. The method was linear from 1 to 3000 ng/mL with a minimum quantifiable limit of 1 ng/mL when 100 μL of plasma was analyzed. Validation results demonstrated high accuracy (≤8.3% deviation) and high precision (≤10% CV) for the quality control samples. The method was also shown to be specific and reproducible. The value of the high sensitivity was demonstrated by quantitation of approximately 100 existing samples that had ZDV below the limit of quantitation using a previously validated, less sensitive HPLC‐UV method utilized in the laboratory. Copyright © 2011 John Wiley & Sons, Ltd.     

Determination of hexabromocyclododecane isomers in sewage sludge by LC‐MS/MS

A method has been developed to determine α, β and γ diastereoisomers of hexabromocyclododecane (HBCD), a brominated flame retardant, in sewage sludge, based on the ultrasonic‐assisted extraction (UAE) of samples with dichloromethane–ACN (1:1) and the subsequent clean‐up of extracts by dispersive solid phase extraction with primary–secondary amine. Levels of HBCD diastereoisomers were determined by LC coupled with ESI MS/MS. Evaluation of the matrix effect showed a high ion suppression for all the diastereoisomers studied, which was counteracted by using a mixture of labelled HBCD diastereoisomers as internal standards. This method yielded recoveries in the range of 79.6–112.5% with SDs equal or lower than 9.1 The limits of detection were 0.3 ng/g for α‐ and β‐HBCD and 0.2 ng/g for γ‐HBCD. The developed method was successfully applied to 19 sludge samples collected from the province of Madrid (Spain). In most of the samples, β‐HBCD was below the method detection limit, whereas α‐ and γ‐HBCD were quantified in all of the sludge samples, and γ‐HBCD was the predominant diastereoisomer in 63% of the analyzed samples and α‐HBCD predominated in the rest.     

Development of a fast LC‐MS/MS assay for the determination of deferiprone in human plasma and application to pharmacokinetics

A fast and accurate liquid chromatography/tandem mass spectrometric (LC‐MS/MS) assay was first developed and validated for the determination of deferiprone in human plasma. The analytes were extracted with acetonitrile from only 50 μL aliquots of human plasma to achieve the protein precipitation. After extraction, chromatographic separation of analytes in human plasma was performed using a Synergi Fusion‐RP 80A column at 30 °C. The mobile phase consisted of methanol and 0.2% formic acid containing 0.2 mM EDTA (60:40, v/v). The flow rate of the mobile phase was 0.8 mL/min. The total run time for each sample analysis was 4 min. Detection was performed using electrospray ionization in positive ion multiple reaction monitoring mode by monitoring the precursor‐to‐parent ion transitions m/z 140.1 → 53.1 for deferiprone and m/z 143.1 → 98.1 for internal standard. A linear range was established from 0.1 to 20 µg/mL. The limit of detection was determined as 0.05 µg/mL. The validated method was estimated for linearity, recovery, stability, precision and accuracy. Intraday and interday precisions were 4.3–5.5 and 4.6–7.3%, respectively. The recovery of deferiprone was in the range of 80.1–86.8%. The method was successfully applied to a pharmacokinetic study of deferiprone in six thalassemia patients. Copyright © 2012 John Wiley & Sons, Ltd.     

Analysis of 16 phthalic acid esters in food simulants from plastic food contact materials by LC‐ESI‐MS/MS

An RP LC‐ESI‐MS/MS method for the determination of the migration of 16 primary phthalic acid esters from plastic samples has been developed using distilled water, 3% acetic acid, 10% alcohol, and olive oil as food simulants. Detection limits were 1.6–18.5 μg/kg in distilled water, 1.4–17.3 μg/kg in 3% acetic acid, 1.4–19.2 μg/kg in 10% alcohol, and 31.9–390.8 μg/kg in olive oil. The RSDs were in the range of 0.07–11.28%. The real plastic products inspection showed that only few analyzed samples were phthalates contaminated. Bis‐2‐ethylhexyl ester and dibutyl phthalate were the common items migrated from the plastic products into food and feeds, but the migration concentrations were far below the limits set by European Union (1.5 mg/kg for bis‐2‐ethylhexyl ester and 0.3 mg/kg for dibutyl phthalate).     

Quantitative determination of perfluorinated surfactants in water by LC-ESI-MS/MS

The surfactants perfluorooctanoate (PFOA), perfluorooctane sulfonate (PFOS), and derivatives of the latter have emerged as globally distributed persistent environmental contaminants. Methods for their reliable quantitative determination at ppt-levels (ng/L) are needed in order to detect their main sources, to elucidate their environmental fate, and to identify potential sinks. The common method for water analysis involves preconcentration by SPE followed by LC coupled to ESI MS/MS (LC-ESI-MS/ MS). All sample preparation steps must be carefully optimized in order to arrive at reliable quantitative data. Two major aspects are important: (i) during SPE, contaminations may arise from materials containing traces of PFOA/S; (ii) during LC-ESI-MS/ MS, ionization yields are suppressed by matrix components and depend upon the analyte concentrations in the extracts. The levels of PFOA/S in the river Roter Main near Bayreuth have been determined using the optimized method.     

LC/MS/MS法同时测定卷烟主流烟气中4种TSNAs

烟草特有亚硝胺（TSNAs）是存在于、烟草制品和卷烟烟气中的一类有害物质。TSNAs在卷烟烟气中的含量很低,卷烟烟气背景复杂,化学成分达3800多种,卷烟烟气中TSNAs的准确定量难度很大。多年来,TSNAs的测量方法随着分析仪器的进步而不断发展,从薄层色谱到GC、LC,从填充柱到毛细管柱,从FID检测到氮磷检测器检测、热能分析仪检测、质谱检测。     

A rapid MCM‐41 dispersive micro‐solid phase extraction coupled with LC/MS/MS for quantification of ketoconazole and voriconazole in biological fluids

A rapid dispersive micro‐solid phase extraction (D‐μ‐SPE) combined with LC/MS/MS method was developed and validated for the determination of ketoconazole and voriconazole in human urine and plasma samples. Synthesized mesoporous silica MCM‐41 was used as sorbent in d ‐μ‐SPE of the azole compounds from biological fluids. Important D‐μ‐SPE parameters, namely type desorption solvent, extraction time, sample pH, salt addition, desorption time, amount of sorbent and sample volume were optimized. Liquid chromatographic separations were carried out on a Zorbax SB‐C₁₈ column (2.1 × 100 mm, 3.5 μm), using a mobile phase of acetonitrile–0.05% formic acid in 5 mm ammonium acetate buffer (70:30, v /v). A triple quadrupole mass spectrometer with positive ionization mode was used for the determination of target analytes. Under the optimized conditions, the calibration curves showed good linearity in the range of 0.1–10,000 μg/L with satisfactory limit of detection (≤0.06 μg/L) and limit of quantitation (≤0.3 μg/L). The proposed method also showed acceptable intra‐ and inter‐day precisions for ketoconazole and voriconazole from urine and human plasma with RSD ≤16.5% and good relative recoveries in the range 84.3–114.8%. The MCM‐41‐D‐μ‐SPE method proved to be rapid and simple and requires a small volume of organic solvent (200 μL); thus it is advantageous for routine drug analysis.     

Validated LC-MS/MS assay for the quantitative determination of nalbuphine in human plasma and its application to a pharmacokinetic study

A solid‐phase extraction–liquid chromatographic–tandem mass spectrometry method for the determination of nalbuphine concentrations in human plasma has been developed. Samples (1 mL) were extracted using a Strata™‐X solid phase extraction cartridges. Chromatographic separation of nalbuphine and naloxone (internal standard) was achieved on a Phenomenex Kinetex PFP (2.6 μm, 100 A, 100 × 2.1 mm) column using a mobile phase consisting of 0.1% formic acid, 15 mM ammonium acetate in deionized water and acetonitrile (60:40, v/v). The flow rate was 0.3 mL/min and the total run time was 2 min. Detection of the analytes was achieved using positive ion electrospray ionization via multiple reactions monitoring mode. The mass transitions were m/z 358 → 340 for nalbuphine and m/z 328 → 310 for naloxone. The assay was linear over the concentration range 0.50–500.00 ng/mL, with correlation coefficients ≥0.995. The lower limit of quantitation was set at 0.5 ng/mL plasma based on an average signal‐to‐noise ratio of 44.79. The intra‐ and inter‐day precision was less than 8.07% in terms of relative standard deviation and accuracy ranged from 94.97 to 106.29% at all quality control levels. The method was applied successfully to determine nalbuphine concentrations in human plasma samples obtained from subjects receiving intravenous administration of nalbuphine. The method is rapid, sensitive, selective and directly applicable to human pharmacokinetic studies involving nalbuphine. Copyright © 2011 John Wiley & Sons, Ltd.     

Graphene as an efficient sorbent for the SPE of organochlorine pesticides in water samples coupled with GC–MS

The determination of organochlorine pesticides in water samples, which are harmful to humans, is very important for environmental risk assessment. Based on the excellent adsorption properties of graphene, an SPE coupled with GC–MS method for the monitoring of organochlorines (four hexachlorcyclohexanes and four dichlorodiphenyltrichloroethanes) was developed. Owing to the hydrophobic interaction and π–π stacking interaction between the analytes and graphene, the analytes quantitatively adsorbed onto the graphene‐based SPE cartridge were eluted by ethyl acetate for analysis. Several parameters influencing the analytical performance, such as the kind of elution, sample volume, reusability of the cartridge, have been investigated in detail. Under the optimal conditions, detection of limits of 1.95–9.38 ng/L, recoveries of 83.9–107.3% at two spiked concentration levels (0.1 and 10 ng/mL) and RSDs in the range of 2.9–7.4% for real water samples were obtained for all the analytes. This work reveals the great potential of graphene in sample preparation procedures.     

Quantification of human and veterinary antibiotics in water and sediment using SPE/LC/MS/MS

An analytical method was developed and tested for four different groups of veterinary antibiotics in both river water and sediment matrices. Solid phase extraction (SPE) was used to enrich and to clean up the aqueous sample. Also, Mcllvaine and ammonium hydroxide buffer solutions were used to extract the compounds from the sediment matrix. High performance liquid chromatography (HPLC) equipped with tandem mass spectrometry (MS/MS) was used to separate and quantify the samples. The range of recoveries (in percent) for tetracyclines (TCs), sulfonamides (SAs), macrolides (MLs), and ionophore polyethers (IPs) in the water matrix were 102.2–124.8, 76.6–124.3, 89.5–114.7, 82.7–117.5 with 1–13 (%) of relative standard deviation respectively with three different concentrations. For sediment, the percent recovery ranges were 32.8–114.8, 62.4–108.9, 53.4–128.4 and 51.3–105.4 for TCs, SAs, MLs and IPs, respectively. The relative standard deviation ranged from 16 – 27 (%) over three different concentrations. The limit of quantification (LOQ) was determined by two different methods and calculated to be in the range of 0.01–0.04 μg/l and 0.3–2.5 μg/kg for TCs, SAs, and MLs in water and sediment, respectively. For IPs, the LOQ was 0.001–0.003 μg/l in river water and 0.4–3.6 μg/kg for sediment. The sediment concentration measured in an agriculture-influenced river was much higher than in the overlying water matrix, indicating a high degree of sediment partitioning for these compounds.     

Validation of a sensitive LC/MS/MS method for the determination of telaprevir and its R‐isomer in human plasma

The purpose of this study was to validate a reversed‐phase high‐performance liquid chromatographic (HPLC), tandem mass spectrometry (MS/MS) assay for the determination of telaprevir and its R‐diastereomer (VRT‐127394) in acidified and nonacidified human plasma. The chromatographic baseline separation of telaprevir and telaprevir‐R was performed on a Waters XBridge^TM BEH Shield C₁₈, 2.1 × 75 mm column with a 2.5 µm particle size, under isocratic conditions consisting of a mobile phase of 50:45:5 water–acetonitrile–isopropanol with 1% ammonia at 0.2 mL/min. This method utilized a stable isotope internal standard with 11 deuterium atoms on the structure of the telaprevir molecule (telaprevir‐d11). An internal standard for the telaprevir‐R (telaprevir‐R‐d11) was also prepared by incubating telaprevir‐d11 in basic solution, which facilitated isomer inter‐conversion. The detection and quantitation of telaprevir, telaprevir‐R, telaprevir‐IS and telaprevir‐R‐IS was achieved by positive ion electrospray (ESI+) MS/MS detection. The assay quantifiable limit was 5.0 ng/mL when 0.100 mL of acidified human plasma was extracted. Accuracy and precision were validated over the calibration range of 5.0–5000 ng/mL. It was demonstrated using patient samples that, contrary to previous recommendations, quantitation of telaprevir does not require acidified plasma. Copyright © 2014 John Wiley & Sons, Ltd.     

Ultra‐performance liquid chromatography MS/MS method for the determination of parabens in compost from sewage sludge: Comparison of the efficiency of two extraction techniques

The efficiency of two extraction techniques—ultrasound‐assisted extraction and pressurized liquid extraction—are compared and evaluated in the determination of parabens in compost samples. The extraction parameters for each technique were accurately optimized. The selected compounds were detected and quantified using ultra‐performance LC MS/MS, operating in negative ESI and in SRM mode. The analytes were separated in less than 5 min. Ethylparaben (ring‐¹³C₆ labeled) was used as an internal standard. Two selective, sensitive, and accurate analytical methods were developed and validated. The LODs of the methods ranged from 3 to 7 ng/g and the LOQs from 10 to 23 ng/g, while inter‐ and intraday variability was under 6% in all cases. The methods were validated separately by using matrix‐matched calibration and recovery assays with spiked samples. Recovery rates ranged from 94.0 to 105.0%. Compost samples were taken from different composting plants. Although the statistical comparison demonstrated no statistically significant differences between the two extraction techniques, the method based on pressurized liquid extraction was more sensitive than the ultrasound extraction based method.     

Simultaneous determination of 103 pesticide residues in tea samples by LC‐MS/MS

A simple and sensitive method was developed and validated for the simultaneous determination of 103 pesticide residues in tea by LC‐MS/MS. For the analysis of the pesticide with polarity, thermal lability or low volatility, this LC‐MS/MS method has an advantage over GC. In this work, residual pesticides were extracted from the tea sample with ACN and then purified using Carb‐NH₂ SPE cartridges. Using the multiple reaction monitoring mode, the pesticides were quantified and identified by the most abundant and characteristic fragment ions. The recoveries obtained for each pesticide ranged between 65 and 114% at three spiked concentration levels. The intra‐day precisions were lower than 19.6%. Good linear relationships were observed with the correlation coefficients r² >0.996 for all analytes. The established method was successfully applied to the determination of pesticide residues in real tea samples.     

Characterization of forced degradation products of ketorolac tromethamine using LC/ESI/Q/TOF/MS/MS and in silico toxicity prediction

Ketorolac, a nonsteroidal anti‐inflammatory drug, was subjected to forced degradation studies as per International Conference on Harmonization guidelines. A simple, rapid, precise, and accurate high‐performance liquid chromatography combined with electrospray ionization quadrupole time‐of‐flight tandem mass spectrometry (LC/ESI/Q/TOF/MS/MS) method has been developed for the identification and structural characterization of stressed degradation products of ketorolac. The drug was found to degrade in hydrolytic (acidic, basic, and neutral), photolytic (acidic, basic, and neutral solution), and thermal conditions, whereas the solid form of the drug was found to be stable under photolytic conditions. The method has shown adequate separation of ketorolac tromethamine and its degradation products on a Grace Smart C‐18 (250 mm × 4.6 mm i.d., 5 µm) column using 20 mM ammonium formate (pH = 3.2): acetonitrile as a mobile phase in gradient elution mode at a flow rate of 1.0 ml/min. A total of nine degradation products were identified and characterized by LC/ESI/MS/MS. The most probable mechanisms for the formation of degradation products have been proposed on the basis of a comparison of the fragmentation of the [M + H]⁺ ions of ketorolac and its degradation products. In silico toxicity of the drug and degradation products was investigated by using topkat and derek softwares. The method was validated in terms of specificity, linearity, accuracy, precision, and robustness as per International Conference on Harmonization guidelines. Copyright © 2014 John Wiley & Sons, Ltd.