Determination of zinc in marine/lacustrine sediments by graphite furnace atomic absorption spectrometry using Pd/Mg chemical modifier and slurry sampling

Effectiveness of Pd/Mg chemical modifier for the accurate direct determination of zinc in marine/lacustrine sediments by graphite furnace atomic absorption spectrometry (GF-AAS) using slurry samples was evaluated. A calibration curve prepared by aqueous zinc standard solution with addition of Pd/Mg chemical modifier is used to determine the zinc concentration in the sediment. The accuracy of the proposed method was confirmed using Certified Reference Materials, NMIJ CRM 7303-a (lacustrine sediment) from National Metrology Institute of Japan, National Institute of Advanced Industrial Science and Technology, Japan, and MESS-3 (marine sediment) and PACS-2 (marine sediment) from National Research Council, Canada. The analytical results obtained by employing Pd/Mg modifier are in good agreement with the certified values of all the reference sediment materials. Although for NRC MESS-3 an accurate determination of zinc is achieved even without the chemical modifier, the use of Pd/Mg chemical modifier is recommended as it leads to establishment of a reliable and accurate direct analytical method. One quantitative analysis takes less than 15 minutes after we obtain dried sediment samples, which is several tens of times faster than conventional analytical methods using acid digested sample solutions. The detection limits are 0.13?µg?g^?1 (213.9?nm) and 16?µg?g^?1 (307.6?nm), respectively, in sediment samples, when 40?mg of dried powdered samples are suspended in 20?mL of 0.1?mol?L^?1 nitric acid and a 10?µl portion of the slurry sample is measured. The precision of the proposed method is 8–15% (RSD).     

Acid predigestion as a slurry pretreatment for the determination of Ca, Cu, K, Mg, Na and Zn in human scalp hair by flame atomic absorption/emission spectrometry with a high-performance nebulizer

A comparison was carried out between the use of wetting agents, Viscalex HV30 or glycerol, and an acid predigestion of the slurry for the determination of major metals (Ca, Cu, K, Mg, Na and Zn) in human scalp hair by FAAS/FAES with a high-performance nebulizer. Human scalp hair was pulverized in a Zr vibrating ball mill over a period of 20 min (mean particle size about 0.8 μm measured by laser diffraction). The use of wetting agents was only found adequate for dilute slurries; thus, Viscalex HV30 can be proposed for the determination of Zn in scalp hair slurries (relative atomization efficiency close to unit). For all cases, the use of acidified slurries with nitric acid at a concentration of 1.0% offers adequate analytical performance: LODs of 5.0, 3.5, 3.1 and 20.0 mg kg^–1 for Ca, Cu, Fe and K, respectively, and 1.7, 0.6 and 3.5 μg kg^–1 for Mg, Na and Zn. The repeatability of the overall method (n = 11), acid predigestion-slurry pretreatment and FAAS/FAES determination expressed as RSD (%), was between 8.7 for Zn and 18.6 for K. The developed methods were applied to 25 human scalp hair samples from healthy adults.     

A new indirect method based on square-wave voltammetry for ceftiofur determination in bovine milk using an alkaline degradation product

In this paper we present a new electroanalytical method for determination of ceftiofur based on the hydrolysis of this antibiotic in 0.04 mol L⁻¹ Britton–Robinson buffer at pH 10 and 60 °C for 60 min (reduction peak at − 0.70 V). Conditions were optimized for complete hydrolysis and quantitative determination of ceftiofur in milk. The method can be successfully used for determination of the antibiotic directly from samples of fluid milk and powder milk spiked to concentrations of 6.0 × 10⁻⁸, 8.0 × 10⁻⁸, and 10 × 10⁻⁸ mol L⁻¹, respectively. Recovery test ranged from 98.28% to 100.83%. The limits of detection and quantification were 3.73 × 10⁻¹⁰ and 1.24 × 10⁻⁹ mol L⁻¹, respectively. The method has the advantage of eliminating interference from proteins present in the sample, thus obviating the need for exhaustive extraction, which often renders other procedures unfeasible in terms of time and reagent cost. In addition, waste generation was found to be lower than in other methods.     

Simultaneous determination of hydride (Se) and non-hydride-forming (Ca,Mg, K,P, S and Zn) elements in various beverages (beer,coffee, and milk), with minimum sample preparation,by ICP–AES and use of a dual-mode sample-introduction system

A method has been developed enabling direct analysis (i.e. after dilution only) of beer, instant coffee, milk, and milk powder by ICP–AES. Analysis of the beverages after dilution with a low concentration of HNO₃ was used for accurate determination of essential minor and trace elements (Ca, Mg, K, P, S, and Zn). Selenium, introduced as the hydride, was determined simultaneously with the other non-hydride-forming elements using the commercial multi-mode sample-introduction system (MSIS). To obtain accurate results, however, some simple pre-treatment was needed. Analysis was also performed after microwave-assisted decomposition of the samples. Three different modes of sample-preparation, i.e. dilution only, partial decomposition (aqua regia treatment), and complete decomposition were compared. The results obtained by use of the three different sample-preparation methods were in very good agreement. Results from analysis of certified reference material (SRM 1459 non-fat milk powder) also verified the accuracy of the methods. The limit of detection obtained for Se using dual-mode sample introduction was 0.5 ng mL^–1, which corresponds to approximately 2 ng g^–1 in beer and approximately 4 ng g^–1 in coffee and milk when using the recommended procedure.     

Investigations on the use of chemical modifiers for the direct determination of trace impurities in Al2O3 ceramic powders by slurry electrothermal evaporation coupled with inductively-coupled plasma mass spectrometry (ETV–ICP–MS)

The direct determination of trace impurities in Al₂O₃ ceramic basic powders by ICP–MS using electrothermal evaporation (ETV) with slurry sampling has been investigated. To increase interference-free analyte volatilization, the use of the palladium-group modifiers (PGM) IrCl₃, Pd(NO₃)₂, and PdCl₂ for the determination of Ca, Fe, Ga, Mg, Mn, Na, Ni, and V in Al₂O₃ powders was studied. Their role, which in ETV–ICP–MS and ETV– ICP–OES is to stabilize the investigated analyte during the ashing phase, to increase vaporization of the matrix, and to reduce transport losses was investigated. Optimum analysis results were obtained with PdCl₂ modifier when 500 ng Pd was used for a sample weight of 100 μg Al₂O₃ injected into the ETV. Calibration was performed by standard addition with aqueous solutions of the analytes. The RSDs calculated from triplicate analysis ranged form 5 to 10%. Detection limits between 0.07 μg g^–1 (Ga) and 1.1 μg g^–1 (Na) were achieved. The accuracy was proven for the elements Ca, Fe, Ga, Mg, Mn, Na, Ni, and V by analyzing an NIST standard reference Al₂O₃ material (SRM 699) with a middle grain size of 16.4 μm. The analytical method was used for the analysis of Al₂O₃ powder (AKP 30, Sumitomo, Japan) with impurities in the low μg g^–1 range and a middle grain size of 1.1 μm. The results obtained for the elements Ca, Fe, Ga, Mg, Mn, Na, Ni, and V were comparable with those obtained by ICP–MS subsequent to conventional decomposition with hydrochloric acid at high pressure.     

Micelle mediated extraction of magnesium from water samples with trizma-chloranilate and determination by flame atomic absorption spectrometry

This article describes an analytical method for the determination of magnesium taking advantage of the cloud point phenomenon employing a suitable chelating agent (chloranilate) for Mg analysis. The method encompasses pre-concentration of the metal chelate followed by flame atomic absorption spectrometry (FAAS) analysis. The chelating agent chosen for this task is a newly synthesised salt of chloranilic acid, trizma-chloranilate, which reacts with Mg but at the same time has a very low affinity for other metallic cations like silicon, aluminium and sodium, which interfere with the determination of Mg in FAAS. The condensed surfactant phase with the metal chelate(s) is introduced into the flame of an atomic absorption spectrometer after its treatment with an acidified methanolic solution. In this way, complex and time-consuming steps for sample treatment are avoided while increased sensitivity is achieved by the presence of both methanol and surfactant in the aspirated sample. The analytical curve was rectilinear in the range of 5-220 mugl(-1) and the limit of detection was as low as 0.75 mugl(-1) with a standard deviation of 5.2%. The method was applied for the determination of Mg in natural and mineral waters with satisfactory results and recoveries in the range of 97-102%.     

Determination of zinc and copper in human hair by slurry sampling employing sequential multi-element flame atomic absorption spectrometry

The present work proposes a direct method based on slurry sampling for the determination of zinc and copper in human hair samples by multi-element sequential flame atomic absorption spectrometry. The slurries were prepared by cryogenic grinding and sonication of the samples. The optimization step was performed using univariate methodology and the factors studied were: nature and concentration of the acid solution, amount sample/slurry volume, sonication time, and particle size. The established experimental conditions are the use of a sample mass of 50 mg, 2 mol L^− 1 nitric acid solution, sonication time of 20 min and slurry volume of 10 mL. Adopting the optimized conditions, this method allows the determination of zinc and copper with detection limits of 88.3 and 53.3 ng g^− 1, respectively, and precision expressed as relative standard deviation (RSD) of 1.7% and 1.6% (both, n = 10) for contents of zinc and copper of 100.0 and 33.3 μg g^− 1, respectively. The accuracy was checked and confirmed by analysis of two certified reference materials of human hair. The procedure was applied for the determination of zinc and copper in two human hair samples. The zinc and copper contents varied from 100.0 to 175.6 and from 3.2 to 32.8 μg g^− 1, respectively. These samples were also analyzed after complete digestion in a closed system and determination by FAAS. The statistical comparison by t-test (95% confidence level) showed no significant difference between these results.     

Method development for the determination of cadmium in fertilizer samples using high-resolution continuum source graphite furnace atomic absorption spectrometry and slurry sampling

The determination of cadmium (Cd) in fertilizers is of major interest, as this element can cause growth problems in plants, and also affect animals and humans. High-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GF AAS) with charge-coupled device (CCD) array detection overcomes several of the limitations encountered with conventional line source AAS, especially the problem of accurate background measurement and correction. In this work an analytical method has been developed to determine Cd in fertilizer samples by HR-CS GF AAS using slurry sampling. Both a mixture of 10 μg Pd + 6 μg Mg in solution and 400 μg of iridium as permanent modifier have been investigated and aqueous standards were used for calibration. Pyrolysis and atomization temperatures were 600 °C and 1600 °C for the Pd-Mg modifier, and 500 °C and 1600 °C for Ir, respectively. The results obtained for Cd in the certified reference material NIST SRM 695 (Trace Elements in Multi-Nutrient Fertilizer) of 16.7 ± 1.3 μg g⁻¹ and 16.4 ± 0.75 μg g⁻¹ for the Pd-Mg and Ir modifier, respectively, were statistically not different from the certified value of 16.9 ± 0.2 μg g⁻¹ on a 95% confidence level; however, the results obtained with the Ir modifier were significantly lower than those for the Pd-Mg modifier for most of the samples. The characteristic mass was 1.0 pg for the Pd-Mg modifier and 1.1 pg Cd for the Ir modifier, and the correlation coefficients (R²) of the calibration were > 0.99. The instrumental limits of detection were 7.5 and 7.9 ng g⁻¹, and the limits of quantification were 25 and 27 ng g⁻¹ for Pd-Mg and Ir, respectively, based on a sample mass of 5 mg. The cadmium concentration in the investigated samples was between 0.07 and 5.5 μg g⁻¹ Cd, and hence below the maximum value of 20 μg g⁻¹ Cd permitted by Brazilian legislation.     

Determination of trace impurities in titanium dioxide by slurry sampling electrothermal atomic absorption spectrometry

A slurry sampling electrothermal atomic absorption spectrometry method for the determination of Al, Ca, Cd, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Na, Ni, Pb, Sr, Tl and Zn in powdered titanium dioxide is described. The behaviour of the titanium matrix in the atomizer and its interferences with the determination of Al, Fe, Co, Ni and Mn were studied. A tungsten carbide modified graphite tube was used to improve the signal shape and the repeatability for the determination of Fe. For all elements, except for Cd and Pb, quantification by a calibration curve established with aqueous standards was possible. No chemical modifier was used throughout in order to minimize contamination. For the contamination risk elements such as Ca, Fe, K, Mg, Na and Zn, the slurry sampling technique allows to achieve limits of detection (3σ of the blank) 5–20 times lower than the solution technique, resulting for these elements in values of 1, 3, 0.5, 0.5, 0.9 and 2 ng g⁻¹, respectively, and, generally being in the range of 0.2 ng g⁻¹ (Cd) to 10 ng g⁻¹ (Al and Tl). The results obtained by the slurry sampling technique are compared with those of other independent methods including four solution methods and neutron activation analysis.     

Bismuth as a general internal standard for lead in atomic absorption spectrometry

Bismuth was evaluated as internal standard for Pb determination by line source flame atomic absorption spectrometry (LS FAAS), high-resolution continuum source flame atomic absorption spectrometry (HR-CS FAAS) and line source graphite furnace atomic absorption spectrometry (LS GFAAS). Analysis of samples containing different matrices indicated close relationship between Pb and Bi absorbances. Correlation coefficients of calibration curves built up by plotting A^Pb/A^Biversus Pb concentration were higher than 0.9953 (FAAS) and higher than 0.9993 (GFAAS). Recoveries of Pb improved from 52–118% (without IS) to 97–109% (IS, LS FAAS); 74–231% (without IS) to 96–109% (IS, HR-CS FAAS); and 36–125% (without IS) to 96–110% (IS, LS GFAAS). The relative standard deviations (n = 12) were reduced from 0.6–9.2% (without IS) to 0.3–4.3% (IS, LS FAAS); 0.7–7.7% (without IS) to 0.1–4.0% (IS, HR-CS FAAS); and 2.1–13% (without IS) to 0.4–5.9% (IS, LS GFAAS).     

Determination of zinc and copper in human hair by slurry sampling employing sequential multi-element flame atomic absorption spectrometry

The present work proposes a direct method based on slurry sampling for the determination of zinc and copper in human hair samples by multi-element sequential flame atomic absorption spectrometry. The slurries were prepared by cryogenic grinding and sonication of the samples. The optimization step was performed using univariate methodology and the factors studied were: nature and concentration of the acid solution, amount sample/slurry volume, sonication time, and particle size. The established experimental conditions are the use of a sample mass of 50 mg, 2 mol L^− 1 nitric acid solution, sonication time of 20 min and slurry volume of 10 mL. Adopting the optimized conditions, this method allows the determination of zinc and copper with detection limits of 88.3 and 53.3 ng g^− 1, respectively, and precision expressed as relative standard deviation (RSD) of 1.7% and 1.6% (both, n = 10) for contents of zinc and copper of 100.0 and 33.3 μg g^− 1, respectively. The accuracy was checked and confirmed by analysis of two certified reference materials of human hair. The procedure was applied for the determination of zinc and copper in two human hair samples. The zinc and copper contents varied from 100.0 to 175.6 and from 3.2 to 32.8 μg g^− 1, respectively. These samples were also analyzed after complete digestion in a closed system and determination by FAAS. The statistical comparison by t-test (95% confidence level) showed no significant difference between these results.     

Simultaneous determination of hydride forming (As, Bi, Ge, Sb, Se, Sn) and Hg and non-hydride forming (Ca, Fe, Mg, Mn, Zn) elements in sonicate slurries of analytical samples by microwave induced plasma optical emission spectrometry with dual-mode sample introduction system

A slurry sampling method for the simultaneous determination of hydride forming (As, Bi, Ge, Sb, Se, Sn) and Hg and non-hydride forming (Ca, Fe, Mg, Mn, Zn) elements, without total sample digestion has been developed using the commercial dual-mode sample introduction system (MSIS) coupled with microwave induced plasma optical emission spectrometry (MIP-OES) from biological and environmental reference materials and real samples. The main advantage of this system is its simultaneous determination of elements that form volatile vapor species and elements that do not, without any instrumental changes. Optimization of reaction, nebulization and instrumental conditions was performed to characterize the new system. Slurry concentration up to 4% m/v (particles < 100 μm) prepared in 10% HNO₃ containing 100 μL of decanol, by application of ultrasonic agitation, was used with calibration by the standard addition technique. An ultrasonic probe was used to homogenize the slurry in the quartz cup just before its introduction into the reaction/nebulization system; the multimode sample introduction system (MSIS) combines the benefits of nebulization and vapor generation in a single device. Detection limits (LOD, 3σ_blank, peak area) of 0.07, 0.29, 0.25, 0.10, 0.12, 0.14, 0.11, 0.28, 0.42, 0.02, 0.21 and 0.34 μg g^− 1 were obtained for As, Bi, Ge, Sb, Se, Sn, Hg, Ca, Fe, Mg, Mn and Zn, respectively. The relative standard deviations were ca. 10%, adequate for slurry analysis. To test the accuracy, six certified reference materials were analyzed with the analyte concentrations mostly in the μg g^− 1 level. Measured concentrations are in satisfactory agreement with certified values for the biological reference materials (LUTS-1, DOLT-2) and environmental reference materials (PACS-1, GWB 07302, NIST 2710, NBS 1633b), all adequate for slurry sampling. The method was successfully applied to the determination of the elements in real samples (coal fly ash, lake sediment, sewage). The method requires small amounts of reagents and reduces contamination and losses.     

Preconcentration of cobalt using Amberlyst 36 as a solid-phase extractor and its determination in various environmental samples by flame atomic absorption spectrometry

A new and simple column-solid-phase extraction method has been developed to separate and preconcentrate trace cobalt in water and soil prior to its determination by flame atomic absorption spectrometry (FAAS). Different factors such as pH of sample solution, sample volume, amount of resin, flow rate of aqueous solution, volume and concentration of eluent, and matrix effects for preconcentration were optimized. Under optimized experimentally established conditions, an analytical detection limit of 0.44?µg?L^?1, precision (RSD) of 1.9%, enrichment factor of 200, and capacity of resin of 82?mg?g^?1 were obtained. The method was applied for cobalt determination by FAAS in tap water, natural drinking water, soil, and roadside dust samples. The accuracy of the method is confirmed by analysing standard reference material (Montana Soil, SRM 2711).     

Determination of macro- and micronutrients in plant leaves by high-resolution continuum source flame atomic absorption spectrometry combining instrumental and sample preparation strategies

A method for determination of B, Ca, Cu, Fe, K, Mg, Mn, Mo, P, S and Zn in plant tissues by high-resolution continuum source flame atomic absorption spectrometry (HR-CS FAAS) is proposed. This method is based on special features of HR-CS-AAS, such as side pixel registration, wavelength integrated absorbance, and molecular absorption bands, for determining macro- and micronutrients in foliar analysis without requiring several different strategies for sample preparation and adjustment of the analytes concentration ranges. Plant samples were analyzed and results for certified materials were in agreement at a 95% confidence level (paired t-test) with reference values. Recoveries of analytes added to plant digests varied within the 82–112% interval. Relative standard deviations (n = 12) were lower than or equal to 5.7% for all analytes in all concentration ranges.     

Direct determination of impurities in high purity silicon carbide by inductively coupled plasma optical emission spectrometry using slurry nebulization technique

A novel method for the determination of Al, Ca, Cr, Cu, Fe, Mg, Mn, Ni and Ti in high purity silicon carbide (SiC) using slurry introduction axial viewed inductively coupled plasma optical emission spectrometry (ICP-OES) was described. The various sizes of SiC slurry were dispersed by adding dispersant polyethylene imine (PEI). The stability of slurry was characterized by zeta potential measurement, SEM observation and signal stability testing. The optimal concentration of PEI was found to be 0.5 wt% for the SiC slurry. Analytical results of sub-μm size SiC by the slurry introduction were in good accordance with those by the alkaline fusion method which verified that determination could be calibrated by aqueous standards. For μm size SiC, results of most elements have a negative deviation and should be calibrated by the Certified Reference Material slurry. Owing to a rather low contamination in the sample preparation and stability of the slurry, the limits of detection (LODs), which are in the range of 40-2000 ng g⁻¹, superior to those of the conventional nebulization technique by ICP-OES or ICP-MS.     

Simultaneous Determination of Ten Antibiotic Residues in Milk by UPLC

An analytical method for rapid screening and quantitative determination of ten antibiotics (chloramphenicol, thiamphenicol, tetracycline, oxytetracycline, chlortetracycline, metacycline, doxycycline, cefoperazone, ceftriaxone and cefaclor) residues in milk was developed using ultra performance liquid chromatography with photodiode array detector. After extraction with McIIvaine buffer + methanol (8 + 2), the extract was cleaned up with solid-phase extraction cartridge. The conditions of sample extraction, cleaning and separation were optimized. The average spiked recoveries of milk samples were 52.1–68.0, 70.1–81.0 and 76.2–101.0% at spiked levels of 0.1, 0.5, 2.5 μg g^?1, respectively with precisions of 3.3–15.9%. The limits of detection and quantification were 0.003–0.022 and 0.01–0.08 μg g^?1, respectively. The proposed method has been applied to the determination of antibiotics in actual milk samples with satisfactory results.     

Evaluation and Application of the Internal Standard Technique for the Direct Determination of Copper in Fruit Juices Employing Fast Sequential Flame Atomic Absorption Spectrometry

Abstract

The present paper describes the evaluation and application of internal standard for the determination of copper in fruit juices, employing Fast Sequential Flame Atomic Absorption Spectrometry (FS FAAS). The internal standards tested were indium, cobalt, and nickel using correlation graphs. However, indium was used, considering the composition of the samples. After this step, copper was determined in fruit juices using indium as internal standard. This method allows the determination of copper with a limit of quantification of 0.011 mg L^?1. The fruit juice samples selected for analysis were of grape, orange, pineapple, peach, cashew, and strawberry. The contents of copper in these samples varied from 0.02 to 0.42 mg L^?1. The analytical results were compared with the results obtained by analysis of these samples after complete mineralization using acid digestion and determination employing FS FAAS. The statistical comparison by a t-test (95% confidence level) showed no significant difference between the results. The relative standard deviations (RSD) with and without the use of the internal standard for a copper solution containing 0.4 mg L^?1 were of 0.62 and 1.94%, respectively. The use of indium as internal standard provided more accurate analytical results, as well as better analytical performance for the determination of copper in juice samples.     

Determination of the ratio of calcium to phosphorus in foodstuffs by dynamic reaction cell inductively coupled plasma mass spectrometry

An inductively coupled plasma mass spectrometer (ICP–MS) equipped with a dynamic reaction cell (DRC) was used for the determination of Ca and P in foodstuffs. In this study, two different reaction gases, CH₄ and O₂, were introduced successively through the different channels to alleviate different interferences in the same analysis run. The effect of the operating conditions of the DRC system was studied to get the best signal-to-noise ratio for each element. The interfering ⁴⁰Ar⁺ at m/z 40 was reduced in intensity by up to five orders of magnitude by using 1.0 mL min^–1 CH₄ as reaction cell gas in the DRC. On the other hand, by using O₂ as the reaction gas, ³¹P⁺ was converted to ³¹P¹⁶O⁺ that could be detected at m/z 47 where there was less interference. The limits of detection for Ca and P were 0.2 ng mL^–1 and 0.3 ng mL^–1, respectively. This method was used to determine the concentrations of Ca and P and the ratio of Ca to P in NIST SRM 1549 non-fat milk powder and NIST RM 8345 whole milk powder reference materials and an infant milk powder and an infant cereal-rice sample purchased locally. The results for the reference samples agreed satisfactorily with the reference values. The accuracy of the determination was better than 4.1 and 0.9% for Ca and P, respectively. The results for infant milk powder and infant cereal were also found to be in good agreement with the value on the bottle label. Precision (RSD) between sample replicates was better than 4.8% for all the determinations.     

Determination of selenium in biological samples by slurry sampling-electrothermal vaporization-in situ fusion-isotope dilution-microwave-induced nitrogen plasma mass spectrometry

Determination of selenium in certified reference biological materials by slurry sampling electrothermal vaporization (ETV)-isotope dilution (ID)-microwave-induced nitrogen plasma mass spectrometry (MIP-MS) was performed. Several parameters such as the heating conditions were studied in order to obtain optimal conditions. A special heating stage called the in situ fusion stage was applied just before the pyrolysis stage in the electrothermal vaporization process in order to fuse the biological sample and to achieve selenium isotope-equilibration between selenium in the sample and the ⁷⁸Se spike solution. The slurry sample containing an appropriate amount of biological sample, ⁷⁸Se spike solution, and sodium hydroxide as an alkaline flux was injected into the electrothermal vaporization unit. The slurry sample was in situ fused, pyrolyzed, and then vaporized. The ion counts at m/z=78 and 80, the spike and reference isotopes, respectively, could be measured accurately without interference caused by argon since nitrogen plasma was used. The analytical utility of the proposed slurry sampling-electrothermal vaporization-in situ fusion-microwave-induced nitrogen plasma mass spectrometry was evaluated by determining the selenium concentration in certified reference biological materials, and the analytical results obtained were in good agreement with the certified values. The limit of detection for selenium was 90 ng g⁻¹. The relative standard deviation of the determination of selenium was 8–15% with a high sample throughput (less than 30 min per sample including a slurry preparation.)     

Determination of Manganese in Cassava Leaves by Slurry Sampling Flame Atomic Absorption Spectrometry

Abstract

Cassava, Manihot esculenta crantz, constitutes one of the main foods consumed by most of the population of developing countries, mainly in the population of low income. It is largely used for its low cost and the diversity of its root and leaves products. In this paper, a slurry sampling flame atomic absorption spectrometric method for the determination of manganese in cassava leaves is proposed. The slurry sampling was used in order to shorten the analysis time and to minimize the problems associated with solid sample treatment such as wet acid digestion, dry-ashing, sample contamination, and analyte loss. The samples of cassava leaves were washed with extran 10% (v/v), soon afterwards they were dried in an oven to 60°C, triturated in a mill of spheres, and the obtained material was sifted in a mesh of 100 micrometers. Then 0.1 g of the sample was weighed in a balloons volumetric flask, the volume was completed with 25 mL of acid nitric 2,0 mol L^?1, and followed by 20 minutes in an ultrasonic bath and subsequent reading in FAAS. The analyses of the certified reference material of spinach and apple leaves evidenced the accuracy of the method.

The proposed method was applied for the determination of manganese in four samples of cassava leaves acquired in markets from Feira de Santana City, Brazil. The concentration of manganese found in cassava leaves varied from 202.7 to 181.3 µg g^?1, with detection and quantification limits of 0.17 and 0.56 µg g^?1, respectively. The precision expressed as relative standard deviation (RSD) was 1.7 and 3.2% (n = 10) for 100 and 12 µg g^?1, respectively.