BEPCⅡ超导腔高次模阻抗抑制优化研究

BEPCⅡ500MHz超导腔是BEPCⅡ储存环的关键设备,腔中高次模的分布和阻抗将很大程度上直接影响束流的稳定.因此,研究BEPCⅡ超导腔的高次模分布和高次模吸收器的吸收效果对实现BEPCⅡ指标至关重要.为此,通过改变高次模吸收器的位置、铁氧体吸收材料的长度、厚度以及腔的渐变过渡波导的角度等对BEPCⅡ超导腔高次模阻抗抑制进行了模拟优化研究,从而找到并确定了吸收器对高次模阻抗抑制的最优值.同时,为证实模拟计算结果的正确性,对BEPCⅡ超导模型腔进行了高次模分布和吸收测量,得到了与计算一致的结果.结果表明,经过细致优化腔的高次模吸收器,腔中大部分高次模被深度吸收了,那些具有潜在危险的高次模阻抗值降到了阈值以下,满足BEPCⅡ束流阻抗要求     

吸收材料对超导高频腔高次模抑制的实验研究

束流粒子通过加速腔的基模加速,以达到所需的能量值. 由于腔本身的多谐性,束流在超导腔里面会激发起高次模,其中其电场分布对粒子加速起到负面作用的,称之谓有害高次模,减小或抑制有害高次模是加速腔研究的一个重要环节,利用铝模型腔对超导腔的高次模抑制进行研究,给出测量结果,研究表明:铁氧体是很好的微波吸收材料,对于所研究的超导腔内的高次模有着良好的吸收效果.     

S波段四腔强流相对论速调管的设计和实验研究

本文根据四腔强流相对论速调管设计过程中出现的高次模振荡现象,采用电磁场软件模拟,分析了这种振荡的产生原因,给出抑制这种高次模振荡的方法.利用二维和三维模拟软件,研究了谐振腔谐振频率、谐振腔Q值、漂移管长度、特性阻抗等参数的变化对高次模振荡的影响,模拟上验证了高次模振荡抑制方法的有效性,并在输出端模拟获得了功率2.13 GW、效率26%、增益60 dB的输出微波,实现了2D,3D中高次模振荡的有效抑制.最终在实验中获得了功率1.9 GW、效率24%、增益61 dB的输出微波.     

0.3 THz TM10, 1, 0模同轴耦合腔链

通过本征方程研究了工作在太赫兹(THz)频段的高次模同轴谐振腔,讨论了TM_{m, 1, 0}模,TM_{m, 2.0}模与TM_{m, 1, 1}模的谐振频率与腔体的几何参数之间的关系,并给出了工作模式的选择依据。在此基础上,提出了一种新型的0.3 THz TM_{10, 1, 0}模同轴耦合腔链,使用等效电路模型和CST-MWS软件对耦合腔链的色散特性、特征阻抗和电场分布等冷腔特性进行了分析和仿真,并着重分析和总结了耦合腔链的几何参数对色散特性和特征阻抗的影响。研究结果表明:对于工作在THz频段的高次模同轴耦合腔链,采用TM_{10, 1, 0}模为工作模式是合理的选择; 工作于2π腔模的0.3 THz TM_{10, 1, 0}模同轴耦合腔链具有较大的特征阻抗,但模式间隔较小,因此可将其应用于窄带太赫兹扩展互作用器件; 增大高次模耦合腔链的耦合槽张角是增大模式间隔的最佳途径。     

束流负载与束团相位补偿

分析研究了电子储存环上的势阱扰动,分析解给出了各束团同步相移、频移随高次模参数变化的规律.该研究结果可帮助我们优化高频腔的工作模式(通过调节调谐杆的位置来改变高次模的频率)和环上束团的分布,以减小束流负载效应,还可帮助我们利用谐波腔来补偿束团相位的变化.     

强耦合腔量子电动力学中单原子转移的实验及模拟

对于强耦合腔量子电动力学系统中以自由下落方式转移原子与腔模强耦合作用过程进行了实验研究,并在理论上利用蒙特卡罗方法对整个实验过程进行了模拟.根据模拟的高精度光学微腔实时记录的原子穿腔信号,获得了原子与腔模相互作用以及冷原子的参数等基本信息,包括不同初始条件下原子与腔模相互作用时腔的透射谱、单个原子在腔内的驻留时间、原子到达腔模时刻的概率分布以及原子到达腔模的动能分布等,并作为对比给出了相应的实验结果.基于模拟结果,实验上建立了腔内光学偶极阱来俘获单个原子,测量的单原子的腔内俘获寿命达到5 ms,比自由穿越时延长了约30倍.该研究对于原子-腔受限空间内,以自由下落方式转移原子以及原子与腔的耦合过程给出详细的分析,有助于对类似实验结果的分析和系统参数的优化.     

1.3GHz新结构超导实用单胞腔物理设计

报道了一个新设计的单胞腔,其表面电场峰值与加速梯度之比值E_p/E_acc小于1.8.把它做为9胞腔的半端胞时,其中间胞π模的E_p/E_acc可以低到2.024,胞-胞间耦合系数k可高达1.95%.并用阻带模型计算了单胞腔的高次模特性;阐述了超导驻波腔腔形的概念、腔几何参数定义、腔胞和束管设计原则、加速模和高次模计算方法,并讨论了程序计算的可靠性条件.     

双间隙同轴腔加载波导滤波器输出回路设计

采用高次模同轴输出腔结构和双间隙耦合谐振腔电路结构是提高速调管频率、功率和带宽的两个重要方式。将这两种电路形式相结合,利用等效电路法推导了滤波器加载双间隙耦合输出回路的间隙阻抗实部计算公式。通过等效电路分析和3维电磁场计算软件模拟,研究了降低高次模式双间隙耦合输出回路外观品质因数的方法。最终设计加载滤波器使得输出回路模型带宽达到9.7%。     

"神龙一号"加速器的BBU不稳定性分析

"神龙一号"加速器在束流调试初期出现了严重的BBU,该BBU是由偏心束流通过多功能腔时激励的TMllo 模引起的.分别以解析分析、数值计算和实验测量等方法对多功能腔的高频特性进行分析.几种方法得到的TMllo模频率与实验结果吻合,而横向耦合阻抗则有倍数之差,但都证明多功能腔在TMllo模式下的横向耦合阻抗过大,是激励BBU的最主要的因素.为此,设计了对多功能腔其他功能不产生影响的可以轴向伸缩的网罩.用来屏蔽多功能腔间隙.使用网罩后效果非常显著,实验结果表明,BU受到抑制,束流脉冲中的高频振荡消失.     

非均匀束团在储存环高频腔中产生的高次模功率

通过分析束流频谱与高频腔高次模的相互作用,提出了计算单束流和双束流储存环中非均匀束团产生的高频腔高次模功率的方法,推导出了这两种情况下的一般通用公式,并对所得到的解析结果进行了比较和讨论.     

Cavity and HOM coupler design for CEPC

In this paper we will show a cavity and higher order mode(HOM) coupler designing scheme for the Circular Electron-Positron Collider(CEPC) main ring. The cavity radio frequency(RF) design parameters are shown in this paper. The HOM power is calculated based on the beam parameters in the Preliminary Conceptual Design Report(Pre-CDR). The damping results of the higher order modes(HOMs) and same order modes(SOMs) show that they reach the damping requirements for beam stability.     

A coaxial HOM coupler for a superconducting RF cavity and its low-power measurement results

A resonant buildup of beam-induced fields in a superconducting radio frequency(RF)cavity may make a beam unstable or a superconducting RF cavity quench. Higher-order mode(HOM)couplers are used for damping higher-order modes to avoid such a resonant buildup. A coaxial HOM coupler based on the TTF (TESLA Test Facility)HOM coupler has been designed for the superconducting RF cavities at the Proton Engineering Frontier Project(PEFP)in order to overcome notch frequency shift and feed-through tip melting issues. In order to confirm the HOM coupler design and finalize its structural dimensions, two prototype HOM couplers have been fabricated and tested. Low-power testing and measurement of the HOM couplers has shown that the HOM coupler has good filter properties and can fully meet the damping requirements of the PEFP low-beta superconducting RF linac.     

A coaxial HOM coupler for a superconducting RF cavity and its low-power measurement results

A resonant buildup of beam-induced fields in a superconducting radio frequency (RF) cavity may make a beam unstable or a superconducting RF cavity quench. Higher-order mode (HOM) couplers are used for damping higher-order modes to avoid such a resonant buildup. A coaxial HOM coupler based on the TTF (TESLA Test Facility) HOM coupler has been designed for the superconducting RF cavities at the Proton Engineering Frontier Project (PEFP) in order to overcome notch frequency shift and feed-through tip melting issues. In order to confirm the HOM coupler design and finalize its structural dimensions, two prototype HOM couplers have been fabricated and tested. Low-power testing and measurement of the HOM couplers has shown that the HOM coupler has good filter properties and can fully meet the damping requirements of the PEFP low-beta superconducting RF linac.     

LOM and HOM damping study in a superconducting deflecting cavity for ALS at LBNL

Superconducting deflecting cavities can be used in synchrotron light source to generate subpicosecond X-ray pulses while the impedance of the lower order modes (LOM) and higher order modes (HOM) in the cavity should be kept below an accepted level to avoid beam instability. These modes can be damped by adding waveguide on beam pipe. Detailed simulation of Q in CST Microwave Studio is introduced and experiment results on an aluminum model cavity with damping waveguide are reported to make a comparison.     

TESLA式高阶模衰减器的改进与设计研究

为了消除超导加速腔中高阶模场对加速粒子的影响, 在DESY的高阶模耦合器结构的基础上本文提出了改进的耦合器. 用HFSS程序针对1.5cell腔设计优化了高阶模耦合器, 得到高阶模耦合器对几种主要模式的吸收. 研究结果表明, 采用新型结构后, 衰减器对主要有害模的衰减由－40dB提高到－15dB, 使原有高阶模衰减器的性能明显提高. 该高阶模衰减器也适用于国产2cell超导腔的使用.     

Stop band characteristics of a TESLA cavity coaxial-type HOM coupler

A TTF-type coaxial higher order modes (HOM) coupler has been used in a TESLA 9 cell cavity. It is impossible to measure the stop band characteristics of the HOM coupler with the cavity. A measurement device for the coaxial transmission line type for the HOM coupler has been designed at Peking University. Experimentally it was shown that the average voltage standing wave ratio of the coaxial transmission line is smaller than 1.08. The experimental results of the stop band characteristics of the TTF-type HOM coupler have been fitted for the simulation. This paper describes the design of the measurement device and discusses the experimental and simulation results of stop band characteristics of the HOM coupler.     

Stop band characteristics of a TESLA cavity coaxial-type HOM coupler

A TTF-type coaxial higher order modes (HOM) coupler has been used in a TESLA 9 cell cavity. It is impossible to measure the stop band characteristics of the HOM coupler with the cavity. A measurement device for the coaxial transmission line type for the HOM coupler has been designed at Peking University. Experimentally it was shown that the average voltage standing wave ratio of the coaxial transmission line is smaller than 1.08. The experimental results of the stop band characteristics of the TTF-type HOM coupler have been fitted for the simulation. This paper describes the design of the measurement device and discusses the experimental and simulation results of stop band characteristics of the HOM coupler.     

Design of a higher harmonic cavity for the SSRF storage ring

Higher harmonic cavity used in the third generation synchrotron light source increases the Touschek lifetime.The higher harmonic cavity of Shanghai Synchrotron Radiation Facility(SSRF)is a 1.5 GHz passive superconducting cavity.Its higher order modes(HOM)are extracted by a ferrite HOM damper out of the cryostat.Multi-cell cavity is chosen concerning the voltage.The harmonic cavity dynamics,beam dynamics with passive harmonic cavity and the design of single cell cavity are included in this paper.     

Design of a higher harmonic cavity for the SSRF storage ring

Higher harmonic cavity used in the third generation synchrotron light source increases the Touschek lifetime. The higher harmonic cavity of Shanghai Synchrotron Radiation Facility (SSRF) is a 1.5GHz passive superconducting cavity. Its higher order modes (HOM) are extracted by a ferrite HOM damper out of the cryostat. Multi-cell cavity is chosen concerning the voltage. The harmonic cavity dynamics, beam dynamics with passive harmonic cavity and the design of single cell cavity are included in this paper.     

1+1/2 Cell超导加速腔的本征高阶模场分布研究

为实现高平均流强加速, 需要有效地消除超导加速腔中的高阶模场. 为研制有效的高阶模耦合器, 本文对北京大学DC-SC光阴极超导注入器的核心部件—1+1/2 cell超导加速腔中高阶模场进行了分析研究, 用HFSS程序计算给出前31个高阶模场参数, 与实验测量较为符合. HFSS计算与Superfish计算结果比较符合很好, 验证用HFSS计算可靠, 为以后超导腔的升级研究提供有效的手段.