Highly sensitive octagonal photonic crystal fiber based sensor

In this study, a number of propagation characteristics of hexagonal and octagonal photonic crystal fiber (H-PCF and O-PCF) structures, where both core and cladding are microstructured have been investigated by employing the full vectorial finite element method (FEM). The confinement loss, the effective refractive index and the relative sensitivity coefficient behaviors of the O-PCF and the standard H-PCF are numerically investigated and compared. It is found that under the same design parameters O-PCF structure has significantly lower losses and higher relative sensitivity coefficient compared with H-PCF structure.     

Enhanced sensitivity of hemoglobin sensor using dual-core photonic crystal fiber

A Hemoglobin (Hb) biosensor based on dual-core photonic crystal fiber is proposed and analyzed. In this paper, the effective refractive index dependency on the Hb concentration within a blood sample is utilized in obtaining the transmission spectrum variation. The results are calculated using full vectorial finite element method. Through this study, the effect of the structure geometrical parameters on the sensor performance is optimized to maximize the sensor sensitivity. The numerical results show a sensitivity of 8.013 nm/g/dL for the X-polarized mode at 3.7 cm fiber length and 7.68 nm/g/dL for the Y-polarized mode at 3.2 cm fiber length of the proposed sensor.     

基于游标效应的双芯光子晶体光纤温度传感器

设计了一种基于双芯光纤耦合效应和游标效应的高灵敏度温度传感器,传感器是由2个相差一定长度的双芯光子晶体光纤和单模光纤级联构成。双芯光子晶体光纤通过级联实现游标效应,同时对纤芯中间的气孔填充乙醇实现温度传感。仿真结果表明,该温度传感器在35℃～45℃范围内的平均温度灵敏度可达-20.37 nm/℃。与单纯依靠双芯光子晶体光纤能量耦合效应的传感器相比,该传感器的温度检测灵敏度提高了10倍。     

Temperature-independent curvature sensor based on tapered photonic crystal fiber interferometer

A temperature-independent highly-sensitive curvature sensor by using a tapered-photonic crystal fiber (PCF)-based Mach-Zehnder interferometer (MZI) is proposed and experimentally demonstrated. It is fabricated by sandwiching a tapered-PCF between two standard single mode fibers (SMFs) with the air holes of the PCF in the fusion splicing region being fully collapsed. The tapering of PCF is found to enhance the sensitivity significantly. Large curvature sensitivities of 2.81 dB/m⁻¹ and 8.35 dB/m⁻¹ are achieved in the measurement ranges of 0.36-0.87 m⁻¹ and 0.87-1.34 m⁻¹, respectively, with the resolution of 0.0012 m⁻¹ being guaranteed. The proposed sensor also shows negligible temperature sensitivity less than 0.006 dB/°C.     

超低温度系数的光子晶体光纤Sagnac压力传感器

 提出了一种基于光子晶体光纤Sagnac干涉仪的横向压力传感器。使用的光子晶体光纤为低双折射光纤,首先预先在Saganc环中的光子晶体光纤上施加初始压力,使Sagnac干涉仪产生正弦干涉光谱,然后再将被测物体放在光子晶体光纤上,由于被测物体重力的作用,Saganc干涉仪输出的光谱产生移动,实现横向压力传感测量。传感器具有高灵敏度0.529 nm/(N·mm)及超低的温度系数-0.4 pm/℃,其环境温度的影响可以忽略。     

超低温度系数的光子晶体光纤Sagnac压力传感器

提出了一种基于光子晶体光纤Sagnac干涉仪的横向压力传感器。使用的光子晶体光纤为低双折射光纤,首先预先在Saganc环中的光子晶体光纤上施加初始压力,使Sagnac干涉仪产生正弦干涉光谱,然后再将被测物体放在光子晶体光纤上,由于被测物体重力的作用,Saganc干涉仪输出的光谱产生移动,实现横向压力传感测量。传感器具有高灵敏度0.529 nm/(N·mm)及超低的温度系数-0.4 pm/℃,其环境温度的影响可以忽略。     

A review of photonic crystal fiber sensor applications for different physical quantities

Since the early conceptual and practical demonstrations in the late 1990s, photonic crystal fibers (PCFs) have attracted considerable interest by virtue of their promise to deliver a unique range of optical properties that are simply not possible in standard fiber types. Hollow-core photonic band gap fiber has the potential to overcome some of the fundamental limitations of solid fiber as they also provide a unique medium for a range of light. PCF also be used as a unique optical material to make sensors due to the air-holes that can be filled with different materials (liquid, gas or even solid) to alter the difference of refractive index (RI) in the two modes, has been used in various sensing search fields. The application of PCF on physical quantities is discussed, and the recent results on temperature, magnetic, strain and vibration are reviewed. These developments demonstrate that the enlarged complexity and decreased accuracy of sensors offered by PCF make it useful in a wide range of engineering monitoring applications.     

High-temperature sensor using a Fabry-Perot interferometer based on solid-core photonic crystal fiber

A micro Fabry-Perot interferometer(M-FPI) is constructed by splicing a short section of polarizationmaintaining photonic crystal fiber(PM-PCF) to an end-cleaved single-mode fiber with controllable offset. Due to the high effective optical path difference induced by the solid core of the PCF,the M-FPI has an ultrasmall cavity of approximately 110μm.The temperature sensitivity within a range from 33℃to approximately 600℃is measured to be 13.8 pm/℃,which shows good agreement with the theoretical result.This proposed sensor has the advantages of ultracompact size and high stability.Therefore,it is suitable for various space-limited sensing applications in harsh environments.     

High sensitivity plasmonic temperature sensor based on a side-polished photonic crystal fiber

A high sensitivity plasmonic temperature sensor based on a side-polished photonic crystal fiber is proposed in this work.In order to achieve high sensitivity and high stability,the gold layer is coated on the side-polished photonic crystal fiber to support surface plasmon resonance.The mixture of ethanol and chloroform is used as the thermosensitive liquid.The performances of the proposed temperature sensor were investigated by the finite element method(FEM).Simulation results indicate that the sensitivity of the temperature sensor is as high as 7.82 nm/℃.It has good linearity(R;=0.99803),the resolution of 1.1×10;℃,and the amplitude sensitivity of 0.1008℃;.In addition,the sizes of the small air hole and polishing depth have little influence on the sensitivity.Therefore,the proposed sensor shows a high structure tolerance.The excellent performance and high structure tolerance of the sensor make it an appropriate choice for temperature measurement.     

Intensity curvature sensor based on photonic crystal fiber with three coupled cores

An intensity curvature sensor using a Photonic Crystal Fiber (PCF) with three coupled cores is proposed. The three cores were aligned and there was an air hole between each two consecutive cores. The fiber had a low air filling fraction, which means that the cores remain coupled in the wavelength region studied. Due to this coupling, interference is obtained in the fiber output even if just a single core is illuminated. A configuration using reflection interrogation, which used a section fiber with 0.13 m as the sensing head, was characterized for curvature sensing. When the fiber is bended along the plane of the cores, one of the lateral cores will be stretched and the other compressed. This changes the coupling coefficient between the three cores, changing the output optical power intensity. The sensitivity of the sensing head was strongly dependent on the direction of bending, having its maximum when the bending direction was along the plane of the cores. A maximum curvature sensitivity of 2.0 dB/m⁻¹ was demonstrated between 0 m and 2.8 m.     

Highly sensitive bend sensor based on Mach-Zehnder interferometer using photonic crystal fiber

Optical fiber bend sensor with photonic crystal fiber (PCF) based Mach-Zehnder interferometer (MZI) is demonstrated experimentally. The results show that the PCF-based MZI is sensitive to bending with a sensitivity of 3.046 nm/m⁻¹ and is independent on temperature with a sensitivity of 0.0019 nm/°C, making it the best candidate for temperature insensitive bend sensors. To that end, another kind of bend sensor with higher sensitivity of 5.129 nm/m⁻¹ is proposed, which is constructed by combining an LPFG and an MZI with zero offset at the second splice mentioned above.     

High-sensitivity temperature sensor based on an alcohol-filled photonic crystal fiber loop mirror

A compact temperature sensor based on a fiber loop mirror (FLM) combined with an alcohol-filled high-birefringence photonic crystal fiber (PCF) is proposed and experimentally demonstrated. The output of the FLM is an interference spectrum with many resonant dips, of which the wavelengths are quite sensitive to the change of the refractive index of the filled alcohol for the interference of the FLM. Simulation analysis predicts a high temperature sensitivity, and experimental results show it reaches up to 6.6 nm/°C for the 6.1-cm-long PCF used in the FLM.     

Polarization maintaining index-guided photonic crystal fiber sensor for slowly varying pressure measurement

The paper presents an experimental investigation of slowly varying pressure measurement using the polarization maintaining photonic crystal fiber (PCF) sensor. Versatility of the sensor has been proved by analyzing its response for various types of time varying pressure profiles viz. exponentially decaying, sinusoidally varying and linearly increasing pressure. Temporal behavior of the sensor has been fully characterised. Dependence on temperature has been explored and it is found that the sensor is an attractive choice for applications in harsh environments.     

Tunable and highly sensitive temperature sensor based on graphene photonic crystal fiber

Optical fiber temperature sensors have been widely employed in enormous areas ranging from electric power industry, medical treatment, ocean dynamics to aerospace. Recently, graphene optical fiber temperature sensors attract tremendous attention for their merits of simple structure and direct power detecting ability. However, these sensors based on transfer techniques still have limitations in the relatively low sensitivity or distortion of the transmission characteristics, due to the unsuitable Fermi level of graphene and the destruction of fiber structure, respectively. Here, we propose a tunable and highly sensitive temperature sensor based on graphene photonic crystal fiber (Gr-PCF) with the non-destructive integration of graphene into the holes of PCF. This hybrid structure promises the intact fiber structure and transmission mode, which efficiently enhances the temperature detection ability of graphene. From our simulation, we find that the temperature sensitivity can be electrically tuned over four orders of magnitude and achieve up to ～ 3.34×10^-3 dB/(cm·℃) when the graphene Fermi level is ～ 35 meV higher than half the incident photon energy. Additionally, this sensitivity can be further improved by ～ 10 times through optimizing the PCF structure (such as the fiber hole diameter) to enhance the light-matter interaction. Our results provide a new way for the design of the highly sensitive temperature sensors and broaden applications in all-fiber optoelectronic devices.     

Endlessly single-mode photonic crystal fiber

We made an all-silica optical fiber by embedding a central core in a two-dimensional photonic crystal with a micrometer-spaced hexagonal array of air holes. An effective-index model confirms that such a fiber can be single mode for any wavelength. Its useful single-mode range within the transparency window of silica, although wide, is ultimately bounded by a bend-loss edge at short wavelengths as well as at long wavelengths.     

Numerical analysis of a temperature sensor based on the photonic band gap effect in a photonic crystal fiber

In this paper we investigate, by the plane wave expansion method and an analytical model, the temperature effect on the photonic band gap fiber, and we report on a numerical demonstration of a temperature sensor based on the photonic band gap (PBG) shift in a solid core photonic crystal fiber (PCF) infiltrated with a high refractive index oil. The bandwidth and the position of the central wavelength of the band gap are the parameters of interests for our temperature sensing purpose. Simulation results were found to be in excellent agreement with the refractive index scaling law and the highest sensitivity of 3.21?nm/°C was achieved, and it will be even higher than the grating based sensors written in PCFs with similar structure.     

光子晶体光纤的全光纤纤芯变形研究

利用有限差分光束传输法分析了全光纤纤芯变形光子晶体光纤中的模场分布以及能量损耗情况.实现了光子晶体光纤的选择性空气孔塌缩,制作了由小纤芯到大纤芯和圆形芯到矩形芯的纤芯变形光子晶体光纤,该光纤在波长1550 nm下以小于0.05 dB的能量损耗实现了光斑的整形.实验结果与模拟结果有很好的一致性. 关键词： 光子晶体光纤 空气孔塌缩 纤芯变形     

Broadband single-polarization photonic crystal fiber

We demonstrate a single-mode photonic crystal fiber that supports only one polarization state in a 220-nm-broad spectral region centered at 727 nm. The fiber has a mode-field diameter of 15.5 microm and background losses of < 15 dB/km in the single-polarization region. To our knowledge, these are the broadest bandwidth and the largest mode size yet reported for a single-polarization fiber.     

Broadband dispersion-compensating photonic crystal fiber

We present a modified dual-core photonic crystal fiber, based on pure silica, with special grapefruit holes in the inner cladding. The fiber has large, broadband negative dispersion, and the dispersion value varies linearly from -380 t o-420 ps/(nm km) in the C band. To decrease the fabrication difficulty, large air holes are adopted. Furthermore, the chromatic dispersion of the fiber is not sensitive to the structure parameters. So the proposed fiber structure can greatly facilitate fiber drawing and can be used for broadband dispersion compensation.     

Efficient way for detection of alcohols using hollow core photonic crystal fiber sensor

Optical Review - In this study, a simple hollow core hexagonal structured photonic crystal fiber is offered and analyzed to discern commonly used different type of alcohols in our daily life. The...