An enzyme electrode for the amperometric determination of glucose

An amperometric method utilizing a glucose electrode has been developed for the determination of blood glucose. The time of measurement is less than 12 s if a kinetic method is used and 1 min if a steady-state method is used. The long-term stability of the electrode is ca. 0.1% change from maximum response per day when stored at room temperature for over 10 months. The enzyme electrode determination of blood sugar compares favorably with commonly used methods with respect to accuracy, precision, and stability. The only reagent required for blood sugar determinations is a buffer solution. The electrode consists of a metallic sensing layer covered by a thin film of immobilized glucose oxidase held in place by means of cellophane. When poised at the correct potential, the current produced is proportional to the glucose concentration.     

Mixed ferrocene-glucose oxidase-carbon-paste electrode for amperometric determination of glucose

The simultaneous incorporation of ferrocene derivatives and glucose oxidase into a carbon-paste matrix results in an effective microelectrode for sensing glucose. The close proximity of the enzymatic, redox mediating and sensing sites offers extremely short response times (t_95%=18 s) compared with early ferrocene-based glucose sensors. Several ferrocene derivatives are evaluated, with 1,1′-dimethylferrocene yielding the best results. The influence of the paste composition, operating potential, glucose concentration and other variables is described. The incorporation of stearic acid into the enzyme-containing paste greatly reduces the interference due to ascorbic acid. The microelectrode is easily fabricated, as time-consuming multi-step immobilization schemes are eliminated. Flow-injection measurements at a rate of 90 samples per hour and relative standard deviations of 3% are also reported.     

An amperometric enzyme electrode for the determination of 3alpha-hydroxysteroids

An enzyme electrode for quantifying the total content of 3alpha-hydroxysteroids is described. 3alpha-Hydroxysteroid dehydrogenase (E.C. 1.1.1.50) was immobilized on the surface of glassy-carbon and low-temperature isotropic-carbon electrodes by intermolecular cross-linking with bovine serum albumin and glutaraldehyde. The effects of the following factors on the response to androsterone were studied: applied potential, the concentration and pH of the pyrophosphate buffer used, and the NAD concentration. The Michaelis-Menten constant for 3alpha-hydroxysteroid dehydrogenase in solution was determined amperometrically with androsterone as substrate (K(m) = 189muM). A preliminary report of the response of the system to serum samples containing a bile acid is presented.     

Mediated amperometric enzyme electrode incorporating peroxidase for the determination of hydrogen peroxide in organic solvents

An amperometric enzyme electrode incorporating horseradish peroxidase is described for the determination of hydrogen peroxide in organic solvents. The enzyme was co-adsorbed with an electron mediator, potassium hexacyanoferrate(II), on the surface of a graphite foil electrode, making reagentless measurement possible. The electrochemical reduction of the enzymatically oxidized mediator was utilized as the analytical signal. Studies in different solvent systems revealed that the electrode could be operated in dioxane, chloroform and chlorobenzene, the last two providing approximately double the sensitivity of the former. The presence of a small amount of aqueous buffer was essential for sensor activity. During 2 weeks of intermittent use, the sensitivity of the electrode decreased to 40% of its initial value. At least 50 assays could be performed with a single sensor.     

On-line removal of redox-active interferents by a porous electrode before amperometric blood glucose determination

A porous reticulated vitreous carbon (RVC) electrode and a disk electrode coupled in tandem in an electrochemical flow cell has been used for electrolytic removal of interferents before amperometric glucose detection. The electrolytic efficiency at the upstream RVC electrode is 100% at a flow rate of 0.1 mL min⁻¹ or lower. Potential interferents such as acetaminophen, ascorbic acid, and uric acid can be completely eliminated by electrolysis at the RVC electrode. A mixed monolayer comprising glucose oxidase (GOD) and ferrocenyl-1-undecanethiol preformed at the downstream gold disk electrode was used as a mediator-based amperometric glucose sensor. The dependence of the amperometric current on the glucose concentration exhibits good linearity across over three orders of magnitude. The glucose measurements were also found to be reproducible (RSD < 3.5%) and accurate. Unlike the chemiluminescence method, this device obviates the use of carcinogenic substrates and the glucose sensor performance is independent of the oxygen present in sample. On the basis that the RVC electrode requires minimal cleanup and the GOD-modified electrode remains stable for a week, the electrochemical flow cell should be amenable for automated on-line removal of redox interferents for other types of enzyme-based biosensors.     

Mediator-free amperometric determination of glucose based on direct electron transfer between glucose oxidase and an oxidized boron-doped diamond electrode

A mediator-free glucose biosensor, termed a “third-generation biosensor,” was fabricated by immobilizing glucose oxidase (GOD) directly onto an oxidized boron-doped diamond (BDD) electrode. The surface of the oxidized BDD electrode possesses carboxyl groups (as shown by Raman spectra) which covalently cross-link with GOD through glutaraldehyde. Glucose was determined in the absence of a mediator used to transfer electrons between the electrode and enzyme. O₂ has no effect on the electron transfer. The effects of experimental variables (applied potential, pH and cross-link time) were investigated in order to optimize the analytical performance of the amperometric detection method. The resulting biosensor exhibited fast amperometric response (less than 5 s) to glucose. The biosensor provided a linear response to glucose over the range 6.67×10⁻⁵ to 2×10⁻³ mol/L, with a detection limit of 2.31×10⁻⁵ mol/L. The lifetime, reproducibility and measurement repeatability were evaluated and satisfactory results were obtained.     

An amperometric glucose oxidase biosensor based on liposome microreactor-chitosan nanocomposite-modified electrode for determination of trace mercury

Journal of Solid State Electrochemistry - A biosensor for trace mercury ions based on glucose oxidase (GOD) immobilized on liposome microreactor and chitosan (CS) nanocomposite through...     

Disposable amperometric glucose sensor electrode with enzyme-immobilized nitrocellulose strip

Electrochemical properties of screen-printed carbon paste electrodes (CPEs) with a glucose oxidase-immobilized and hexamineruthenium (III) chloride ([Ru(NH₃)₆]³⁺) containing nitrocellulose (NC) strip were examined. The NC strip (2×8 mm) placed on the CPEs printed on polyester (PE) film is tightly sealed using another PE film on the top with open edges on both sides. Samples containing macromolecules and particles (e.g. proteins and blood cells) are applied at one edge of the NC strip and reach the detection area, chromatographically separating small molecules (e.g. glucose, ascorbate, acetaminophen, and uric acid) of analytical interests. Since sample volumes and the amount of catalytic reagents (mediator and glucose oxidase) are precisely predefined by the dimension and pore size (8 μm) of the NC strip, the sensor-to-sensor reproducibility and accuracy of analysis are greatly improved. The use of [Ru(NH₃)₆]³⁺ mediator, which exhibits characteristic substantially lowers the applied potential (0.0 V vs Ag/AgCl) for glucose determination and eliminates the interference from other oxidizable species, providing improved analytical results.     

Metal-alloy-dispersed carbon-paste enzyme electrodes for amperometric biosensing of glucose

The preferential electrocatalytic detection of hydrogen peroxide and the selective biosensing of glucose at carbon-paste enzyme electrodes dispersed with bimetallic (Ru–Pt) alloy particles are described. Unlike the marked acceleration of the redox reaction of the peroxide product (versus single metal catalysts), the signals of common interfering compounds shift to higher potentials. Such use of carbon-supported alloy particles thus results in a greatly enhanced sensitivity compared to the dispersion of pure metals, without compromising the remarkable selectivity inherent to metallized carbon biosensors.     

Flow-injection amperometric determination of chlorine at a gold electrode

The applied potential is +0.2 V vs. SCE, flow rate is 1 ml min^?1 and sample volume is 30 μ1. The background electrolyte is 0.05 M phosphate, pH 7.4. Electrode pretreatment is +1.3 V vs. SCE for 40 s, followed by a pre-injection delay of 20 s. Peak current over a receding baseline is used. Linear range extends down to 0.4 μM for chloramine and 0.2 μM for hypochlorite. Sensitivities are 70 and 95 nA μM^? respectively. Time per determination is less than 1.5 min. Monochlorinated glycine is active whereas chlorinated cyanuratesshow no response. Chlorine and monochloramine in river water were determined.     

Copper-modified gold electrode specific for monosaccharide detection Use in amperometric determination of phenylmercury based on invertase enzyme inhibition

The electrochemical oxidation of mono- and disaccharides at various copper-modified electrodes is reported: glassy carbon modified at open circuit or by electrochemical deposition of copper, gold modified by electrochemical deposition, and at bulk copper electrodes. A comparative study of these four electrodes was made by linear sweep voltammetry and amperometry. The maximum oxidation peak separation between disaccharides and monosaccharides is about 200 mV. After optimization, amperometric determination of monosaccharides was done at +0.30 versus Ag/AgCl in 0.15 M NaOH at the copper-modified gold electrode.

Using the developed method, the enzymatic activities of invertase and β-galactosidase were determined through their reaction with sucrose and lactose, respectively. Validation was carried out by a spectrophotometric method based on 3,5-dinitrosalicylic acid, and it was shown that the proposed electrochemical method is more sensitive.

The analytical utility of the copper-modified gold electrode was tested for the determination of organic mercury. Addition of phenylmercury standards to the invertase solution caused a decrease in the enzyme activity, and allowed the determination of phenylmercury in pharmaceutical samples. The concentration has been determined in the 10–55 ng ml⁻¹ range.     

A novel two-enzyme amperometric electrode for lactose determination.

Coimmobilization of beta-galactosidase and glucose oxidase in a redox polymer, polyvinylferrocenium perchlorate (PVF+ ClO4-), led to the development of an enzyme electrode for the determination of lactose. The amperometric response of the electrode was measured at +0.70 V vs. SCE, which was due to the electrooxidation of enzymatically produced H2O2. The effects of the substrate and buffer concentrations as well as the pH on the electrode response were elucidated.     

Nafion coating the ferrocenylalkanethiol and encapsulated glucose oxidase electrode for amperometric glucose detection

This paper describes the fabrication and application of a complex electrode--Nafion film coating ferrocenylalkanethiol (FcC(11)SH) and encapsulated glucose oxidase (GOD) on a gold electrode. FcC(11)SH is employed as a mediator enabling the electron transfer between GOD and the electrode, GOD is encapsulated in polyacrylamide gel to improve the stability of the enzyme, and the Nafion film is coated on the modified electrode to eliminate interferents such as ascorbic acid, uric acid and acetaminophen in amperometric glucose detection. It is noticed that such a complex electrode exhibits excellent catalytic activity for glucose oxidation, and preserves the native structure of GOD and therefore its enzymatic activity. The encapsulated GOD retains more than 80% of its original biocatalytic activity even after 24 days, much longer than that of naked GOD molecules attached directly to the electrode. The oxidation peak current at the modified electrode shows a linear relationship with the glucose concentration in the range from 0.05 to 20 mM with a detection limit of 2.4 μM. In addition, the electrode displays a rapid response and good reproducibility for glucose detection, and has been successfully employed for glucose detection in blood plasma samples.     

Hot-wire amperometric monitoring of flowing streams

This paper describes the design of a hot-wire electrochemical flow detector, and the advantages accrued from the effects of locally increased temperature, mainly thermally induced convection, upon the amperometric monitoring of flowing streams. A new hydrodynamic modulation voltammetric approach is presented, in which the solution flow rate remains constant while the temperature of the working electrode is modulated. Factors influencing the response, including the flow rate, temperature pulse, or applied potential, have been investigated. The hot-wire operation results also in a significant enhancement of the flow injection amperometric response. The minimal flow rate dependence observed with the heated electrode should benefit the on-line monitoring of streams with fluctuated natural convection, as well as various in-situ remote sensing applications.     

Laccase/glucose oxidase electrode for determination of glucose

The electrode involves a layer of co-immobilized glucose oxidase and laccase in a gelatin membrane placed over a modified oxygen electrode. Hexacyanoferrate(III) is added to the samples to oxidize reductive interferents such as ascorbic acid, and the hexacyanoferrate(II) formed is re-oxidized by a laccase-catalyzed reaction. Ascorbic acid is completely eliminated up to a concentration of 20 mM in the sample.     

Flow-injection determination of trace hydrogen peroxide or glucose utilizing an amperometric biosensor based on glucose oxidase bound to a reticulated vitreous carbon electrode

An electron transfer mediator, 8-dimethylamino-2,3-benzophenoxazine (Meldola Blue), dissolved in the carrier solution in a flow-injection system, was found to reduce the oxidation potential for hydrogen peroxide from 600-1200 mV without mediator to-100 mV vs. Ag/AgCl with the mediator present. The very low background current of reticulated vitreous carbon (RVC) at this potential makes it possible to detect very low levels of hydrogen peroxide or glucose. Glucose oxidase was covalently coupled with carbodiimide to RVC, and the RVC was formed into a column inserted in a flow-injection system. The calibration curve was linear from 30 nM to 10 microM glucose with 5 microM mediator. At higher mediator concentrations, the linear range was extended to 1000 microM, but with a much higher background current. The sample throughput was about 60 h(-1). The current response decreased to 50% of the original response after 20 days. The coulometric yield was high because the sample was pumped through the pores of the RVC. It was 16% and 55% at a flow rate of 1 ml min(-1) at mediator concentrations of 5 and 50 microM respectively.     

Voltammetric and amperometric determination of metoclopramide on boron-doped diamond film electrode

New methods for the determination of metoclopramide, antiemetic and gastroprokinetic pharmaceutical, were developed, using differential pulse voltammetry (DPV) and flow injection analysis (FIA) with amperometric detection on a boron-doped diamond film electrode. Electrode pretreatment necessary to ensure the stable results was investigated and it was found, that while DPV requires frequent electrode cleaning, FIA with a sufficiently high flow rate can maintain a stable signal with no signs of electrode passivation. The calculated quantification limits of the DPV and FIA with amperometric detection were 0.13 μmol L⁻¹ and 0.015 mmol L⁻¹, respectively. The applicability of the new methods was verified by the determination of metoclopramide in a pharmaceutical preparation. FIA with amperometic detection proved to be sensitive, accurate and, due to the resistance of the electrode to the passivation, also simple to handle.      

A new catalytic electrode for the amperometric determination of hydrogen peroxide

The electrode is based on the decomposition of H₂O₂ by an inorganic polymer catalyst. The steady -state decomposition currents of H₂0₂ obtained with the catalyst electrode are independent of ionic strength (0.1–1.5) and pH (2.5–10.5). A linear relationship is obtained from 0.02 to 2 mM H₂0₂ in 0.1 M KCl at 25°C.     

Electrocatalytic amperometric determination of amitrole using a cobalt-phthalocyanine-modified carbon paste electrode

Cobalt-phthalocyanine-modified carbon paste electrodes are shown to be excellent indicators for electrocatalytic amperometric measurements of triazolic herbicides such as amitrole, at low oxidation potentials (+0.40 V). The detection and determination of amitrole in flow injection analysis with a modified carbon paste electrode with Co-phthalocyanine is described. The concentrations of amitrole in 0.1 M NaOH solutions were determined using the electrocatalytic oxidation signal corresponding to the Co(II)/Co(III) redox process. A detection limit of 0.04 microg mL(-1) (4 ng amitrole) was obtained for a sample loop of 100 microL at a fixed potential of +0.55 V (vs. Ag/AgCl) in 0.1 M NaOH and a flow rate of 4.0 mL min(-1). Furthermore, the modified carbon paste electrodes offers reproducible responses in such a system, and the relative standard deviation was 3.3% using the same surface, 5.1% using different surface, and 6.9% using different pastes. The performance of the cobalt-phthalocyanine-modified carbon paste electrodes is illustrated here for the determination of amitrole in commercial formulations. The response of the electrodes is stable, with more than 80% of the initial retained activity after 50 min of continuous use.     

Enzyme electrode for glucose determination in whole blood

The development of a glucose sensor suitable for use with whole blood is described. It is based on anodic oxidation at +700 mV of hydrogen peroxide with a platinum electrode covered with a gas permeable membrane. Glucose reacts with glucose oxidase immobilised on the external side of the membrane, and forms hydrogen peroxide which is able to cross the gas permeable membrane due to its high vapour tension, while other electroactive substances that are important interferents are completely blocked. This principle was discovered several years ago but no practical application was presented up to now. Therefore in this work a number of different commercial membranes were tested, in order to obtain a resistant, rapidly responding and interference free sensor to be used in conjunction with a blood gas measurement apparatus. Coimmobilisation of glucose oxidase and catalase was found to be useful for fast response and recovery of the electrode. Using some of the tested membranes, the linearity range is 1-15 mM, CV 5%, response time 90 s, recovery time for the next sample 120 s. The membrane's working life is 2-3 weeks.