Mutual solubility of n-butanol + water under high pressures

The mutual solubilities of {xCH₃CH₂CH₂CH₂OH+(1-x)H₂O} have been determined over the temperature range 302.95 to 397.75 K at pressures up to 2450 atm. An increase in temperature and pressure results in a contraction of the immiscibility region. The results obtained for the critical solution properties are: T_o(U.C.S.T.) = 397.85 K and x_o = 0.110 at 1 atm; $\text{(}\text{dT}{}_{\mathrm{o}}\text{d}\text{p}\text{) = ?(12.0±0.5)×10}{}^{\mathrm{?3}}\text{K atm}{}^{\mathrm{?1}}$ at p < 400 atm and $\text{(}\text{dT}{}_{\mathrm{o}}\text{d}\text{p}\text{) = ?(7.0±0.7)×10}{}^{\mathrm{?3}}\text{K atm}{}^{\mathrm{?1}}$ at 800 atm < p < 2500 atm; $\text{(}\text{dx}{}_{\mathrm{o}}\text{d}\text{T}\text{) = ?(4.0±0.5)×10}{}^{\mathrm{?4}}\text{K}{}^{\mathrm{?1}}$.     

The use of a high efficiency mass separator in activation analysis

The application of high yield mass separators to problems in activation analysis is discussed. The identification of separation parameters including separator yields, memory, resolution and overlap, and sputtering are considered. The use of the mass separator in determining lead by photon activation analysis is described.     

Investigation on water consumption characteristics and water use efficiency of poplar under soil water deficits on the Loess Plateau

The water consumption characteristics and water use efficiency (WUE) of poplar (Populus simonii) were investigated under the condition of three different soil water regimes, which were 70%, 55% and 40% of field capacity (FC), respectively. The results showed that water potential, water content, photosynthetic rate, WUE of leaves, and plant growth rate decreased significantly with reduction in soil water content. At the level of adequate and medium soil water content, rapid growth and biomass accumulation in poplar occurred during May and June, whereas this phenomenon occurred only during May under severe soil drought condition. Total water consumption and biomass growth were the greatest under adequate soil water condition, decreased under medium soil drought condition, and lowest under severe soil drought condition. Total WUE was the highest under medium soil water condition and lowest under severe soil condition. Changing patterns of water consumption for daily rate, every 10-day rate, and month rate were quite different under these three soil water regimes. For all these three treatments, the highest monthly water consumption rate occurred during July and June. The highest water consumption over a 10-day period was during in the second 10 days of July, the first 10 days of July, and the last 10 days of June for these three treatments, respectively. The day for the highest water consumption in the medium and severe drought treatments occurred 1 or 2 months earlier than the adequate soil water treatment. The daily time for the greatest water consumption was different throughout the life span of poplar under these soil water levels. According to these results, we concluded that poplar did not have the characteristics of drought-resistance plants, and we do not recommend that this tree species be planted over a wider range of the Loess Plateau in China.     

Relationship between water use efficiency (WUE) and production of different wheat genotypes at soil water deficit

Through 2-year field experiments, 7 wheat genotypes were better in their field yield. These 7 wheat genotypes and other 3 wheat species, which are being popularized on a large scale in different locations of China, were selected as experimental materials for the sake of measuring their difference in WUE and production and comparing their relationship at soil water deficits, future more, providing better drought resistance lines and theoretical guide for wheat production and practices and exploring anti-drought physiological mechanisms of different wheat genotypes. Under the condition of 3 soil–water–stress treatments (75% field capacity (FC), 55% FC, 45% FC, named level 1, level 2 and level 3, respectively), pot experiments for them were conducted and the related data were collected from their life circle. The main results were as followed: (1) according to the selected soil stress levels, water use efficiency (WUE) of 10 different wheat genotypes was divided into two groups (A and B); group A included genotypes 2, 3, 4, 5, 6, 7, 8, whose WUE decreased basically from level 1 to level 3 and reached individual peak of WUE at level 1; Group 2 included genotypes 1, 9, 10, whose WUE reached their individual peak at level 2; (2) based on total water consumption through all life circle, genotypes 1, 4, 8, 9 had lower water consumption (TWC) at level 1, genotypes 2, 3, 5, 6, 7 lower TWC at level 2, genotype 10 lower TWC at level 3; (3) at level 1, genotypes 2, 3, 4, 5, 6, 7, 8 had higher grain weight of single spike (GWSS), genotypes 1, 9, 10 better GWSS at level 2, which was in good line with individual WUE of different wheat genotypes; (4) by analyzing the indexes related to examining cultivars, it was found that genotypes 1, 2, 3, 4, 5, 6, 9, 10 had longer plant length (PL), spike length (SL), bigger grain number (GN) except genotypes 7 and 8 at level 1, RL was in better line with genotypes 1, 2, 3, 8, 9, 10, but not in the other genotypes at level 1.     

8-Bromo-7-hydroxyquinoline as a photoremovable protecting group for physiological use: mechanism and scope

Two-photon excitation (2PE) of "caged" biomolecules represents a powerful method to investigate the temporal and spatial relevance of physiological function in real time and on living tissue, because the excitation volume can be restricted to 1 fL. Additionally, low-energy IR light is used, which minimizes tissue destruction and enables deeper penetration into tissue preparations. Exploitation of this technology for studying cell physiology requires the further development of photoremovable protecting groups with sufficient sensitivity to 2PE for use in "caged" compounds. 8-Bromo-7-hydroxyquinoline (BHQ) is efficiently photolyzed by classic 1PE (365 nm) and 2PE (740 nm) under simulated physiological conditions (aqueous buffer of high ionic strength, pH 7.2) to release carboxylates, phosphates, and diols-functional groups commonly found on bioactive molecules such as neurotransmitters, nucleic acids, and drugs. It is stable in the dark, soluble in water, and exhibits low levels of fluorescence, which will enable use in conjunction with fluorescent indicators of biological function. BHQ-protected effectors are synthetically accessible. Stern-Volmer quenching, time-resolved infrared (TRIR), and (18)O-labeling experiments suggest that the photolysis occurs through a solvent-assisted photoheterolysis (S(N)1) reaction mechanism on the sub-microsecond time scale. BHQ has the requisite photochemical and photophysical properties as a photoremovable protecting group to regulate the action of biological effectors in cell and tissue culture with light, especially 2PE.     

A desorption calorimetric method for use at high water activities

This paper presents a microcalorimetric technique to simultaneously measure water activity and enthalpy of mixing (differential heat of sorption) as functions of composition at high water activities. The instrument consists of a sorption vessel in a double twin microcalorimeter. A sample at high water activity is placed in one chamber of the vessel and an unsaturated salt solution is injected into another chamber. A tube connects the chambers and diffusion will cause the water in the sample to be desorbed and condensed in the salt solution. As the rate of diffusion is high when the sample is at high water activity it is possible to make detailed studies of phenomena taking place at high water activity. The method has been tested on the system dimethyldodecylamine oxide (DDAO)-water.     

Mutual solubilities of hydrocarbons and water with the CPA EoS

The knowledge of hydrocarbon/water phase equilibria is important in the design and operation of equipment for petroleum transport and refining and petrochemical plants. The presence of water in a hydrocarbon mixture can affect the product quality and damage the operation equipment due to corrosion and formation of gas hydrates. Tracing the concentration of hydrocarbons in aqueous media is also important for technical purposes like preventing oil spills and for ecological concerns such as predicting the fate of these organic pollutants in the environment.     

Mutual exclusivity in the synthesis of high crystallinity and high yield single-walled carbon nanotubes

We report the mutually exclusive relationship between carbon nanotube (CNT) yield and crystallinity. Growth conditions were optimized for CNT growth yield and crystallinity through sequential tuning of three input variables: growth enhancer level, growth temperature, and carbon feedstock level. This optimization revealed that, regardless of the variety of carbon feedstock and growth enhancer, the optimum conditions for yield and crystallinity differed significantly with yield/crystallinity, preferring lower/higher growth temperatures and higher/lower carbon feedstock levels. This mutual exclusivity stemmed from the inherent limiting mechanisms for each property.     

The effects of water interactions in cellulose suspensions on mass transfer and saccharification efficiency at high solids loadings

Water is essential to the hydrolysis and conversion of lignocellulosic materials as it is both the medium through which enzymes diffuse to and products diffuse away from the reaction sites and a reactant in the hydrolysis reaction of the glycosidic bonds within the polysaccharides. However, little is known about how water interactions with the biomass change with solids content and how this affects mass transfer resistances during high solids saccharification. Nuclear magnetic resonance spectroscopy measurements of the T ₂ relaxation times of water in cellulose suspensions were used to demonstrate that increases in solids content led to increases in the physical constraint of water in the suspensions. Moreover, the addition of either glucose (a monosaccharide which end-product inhibits β-glucosidase) or mannose (a stereoisomer of glucose that does not end-product inhibit β-glucosidase) further increased water constraint at all solids contents. The presence of either monosaccharide constrained water and inhibited saccharification rates to similar extents. This observation, coupled with the absence of cellobiose produced in the reactions, demonstrated that the presence of soluble sugars can negatively impact saccharification efficiency simply by increasing water constraint in cellulose suspensions before impacting enzyme activity. Furthermore, results are presented that demonstrate strong correlations between water constraint in cellulose suspensions with diffusivities of enzyme and monosaccharides within the system. These results are discussed in the context of increased viscosity of the aqueous fraction in the suspension resulting from increased water-cellulose and water-solute interactions that ultimately increases diffusion resistances and decreases saccharification rates.     

Investigation on the relationship between leaf water use efficiency and physio-biochemical traits of winter wheat under rained condition

Different statistical methods and path analysis were used to study the relationship between leaf water use efficiency (WUE) and physio-biochemical traits for 19 wheat genotypes, including photosynthesis rate (P_n), stomatal conductance (g_s), transpiration rate (T_r), intercellular concentration of carbon oxide (C_i), leaf water potential (Ψ_w), leaf temperature, wax content, leaf relative water content (RWC), rate of water loss from excised-leaf (RWL), peroxidase (POD) and superoxide dismutase (SOD) activities. The results showed that photosynthesis rate, stomatal conductance and transpiration rate were the most important leaf WUE variables under rainfed conditions. Based on the results of five statistical analyses, it is reasonable to assume that high leaf WUE wheat under the rained could be obtained by selecting breeding materials with high photosynthesis rate, low transpiration rate and stomatal conductance.     

A new cadmium reduction device for the microplate determination of nitrate in water, soil, plant tissue, and physiological fluids

A reusable catalytic reductor consisting of 96 copperized-cadmium pins attached to a microplate lid was developed to simultaneously reduce nitrate (NO3-) to nitrite (NO2-) in all wells of a standard microplate. The resulting NO2- is analyzed colorimetrically by the Griess reaction using a microplate reader. Nitrate data from groundwater samples analyzed using the new device correlated well with data obtained by ion chromatography (r2 = 0.9959). Soil and plant tissue samples previously analyzed for NO3- in an interlaboratory validation study sponsored by the Soil Science Society of America were also analyzed using the new technique. For the soil sample set, the data are shown to correlate well with the other methods used (r2 = 0.9976). Plant data correlated less well, especially for samples containing low concentrations of NO3-. Reasons for these discrepancies are discussed, and new techniques to increase the accuracy of the analysis are explored. In addition, a method is presented for analyzing NO3- in physiological fluids (blood serum and urine) after matrix modification with Somogyi's reagent. A protocol for statistical validation of data when analyzing samples with complex matrixes is also established. The simplicity, adaptability, and low cost of the device indicate its potential for widespread application.     

Characteristics of high efficiency dye-sensitized solar cells

Impedance spectroscopy was applied to investigate the characteristics of dye-sensitized nanostructured TiO2 solar cells (DSC) with high efficiencies of light to electricity conversion of 11.1% and 10.2%. The different parameters, that is, chemical capacitance, steady-state transport resistance, transient diffusion coefficient, and charge-transfer (recombination) resistance, have been interpreted in a unified and consistent framework, in which an exponential distribution of the localized states in the TiO2 band gap plays a central role. The temperature variation of the chemical diffusion coefficient dependence on the Fermi-level position has been observed consistently with the standard multiple trapping model of electron transport in disordered semiconductors. A Tafel dependence of the recombination resistance dependence on bias potential has been rationalized in terms of the charge transfer from a distribution of surface states using the Marcus model of electron transfer. The current-potential curve of the solar cells has been independently constructed from the impedance parameters, allowing a separate analysis of the contribution of different resistive processes to the overall conversion efficiency.     

A yellow-emitting iridium complex for use in phosphorescent multiple-emissive-layer white organic light-emitting diodes with high color quality and efficiency

A cyclometalated iridium(III) complex containing 2-(9,9-diethylfluoren-2-yl)pyridine [Ir(Flpy)₃] was prepared and used in the fabrication of both yellow and white organic light-emitting diodes (OLEDs). A hole-blocking material has been used as a hole barrier layer in-between different emission layers, helping the formation of the hole limitation region. With the proper position of a hole barrier layer and the construction of a four-emission-layer structure involving the use of [Ir(Flpy)₃], the resulting WOLED shows sound device performance as well as very stable color even at high luminances. Such WOLEDs have been demonstrated to reveal superior white light color stability/efficiency trade-off optimization. The Commission Internationale de L’Eclairage (CIE) coordinate differences Δx and Δy are confined to ±0.015 when the luminance increases from 13 to 14806 cd/m². The color rendering index (CRI) of the device is also very good, which varies only from 86 to 87 by changing from the normal direction to 80° off-normal at 12 V. The peak electrophosphorescence efficiency can reach as high as 24.6 cd/A at 168 cd/m²and it can still be kept at 17.2 cd/A at 10834 cd/m². Such outstanding performance renders this all-phosphor WOLED very attractive as a white light source for illumination applications, which typically demand high efficiency, high CRI, and stable color in high brightness work conditions.     

Multivalent supramolecular assembly with ultralong organic room temperature phosphorescence,high transfer efficiency and ultrahigh antenna effect in water

Multivalent supramolecular assemblies have recently attracted extensive attention in the applications of soft materials and cell imaging. Here, we report a novel multivalent supramolecular assembly constructed from 4-(4-bromophenyl)pyridine-1-ium bromide modified hyaluronic acid (HABr), cucurbit[8]uril (CB[8]) and laponite® clay (LP), which could emit purely organic room-temperature phosphorescence (RTP) with a phosphorescence lifetime of up to 4.79 ms in aqueous solution via multivalent supramolecular interactions. By doping the organic dyes rhodamine B (RhB) or sulfonated rhodamine 101 (SR101) into the HABr/CB[8]/LP assembly, phosphorescence energy transfer was realized with high transfer efficiency (energy transfer efficiency = 73–80%) and ultrahigh antenna effect (antenna effect value = 308–362) within the phosphorescent light harvesting system. Moreover, owing to the dynamic nature of the noncovalent interactions, a wide-range spectrum of phosphorescence energy transfer outputs could be obtained not only in water but also on filter paper and a glass plate by adjusting the donor–acceptor ratio and, importantly, white-light emission was obtained, which could be used in the application of information encryption.

An ultralong lifetime supramolecular assembly was constructed via multivalent supramolecular interactions and achieved phosphorescence light harvesting. Multicolor (including white) broad-spectrum outputs could be achieved in water and also on filter paper and a glass plate.