Preparation and magnetic properties of RFeO<Subscript>3</Subscript> nanocrystalline powders

The rare-earth orthoferrites RFeO₃ (R, rare-earth element) crystallize in an orthorhombic distorted perovskite structure. RFeO₃ compounds exhibit interesting physical and chemical properties because of their ionic and electronic defects. Polycrystalline nano-sized RFeO₃ powders were synthesized by the sol–gel combustion method. X-ray powder diffraction indicated that nanocrystalline powders were single ReFeO3 phase, which are agglomerated with average crystallite size of 60–90 nm estimated with the Scherrer’s equation. Magnetic measurements were carried out using a superconducting quantum interference device magnetometer. The influence on hysteresis curve of electronic structure of rare-earth element was investigated for R = Y, La and Nd. Varied magnetic behaviors were observed in these compounds, which are believed to be associated with the different interactions of Fe and rare earths.     

Synthesis and characterization of Pb<Subscript>1–x</Subscript>La<Subscript>x</Subscript>TiO<Subscript>3</Subscript> nanocrystalline powders

Pb_1–xLa_xTiO₃ (PLT) nanocrystalline powders were obtained by polymeric precursor method. The samples were analyzed by differential scanning calorimetry (DSC) and thermogravimetry (TG) techniques to characterize properly the distinct thermal events occurring during synthesis. The X-ray diffraction patterns show a tetragonal structure for the samples with x=0.10 and 0.15. An increase of the lanthanum concentration to x=0.20 led to a highly symmetric structure, cubic on average. The powders obtained at the end of the synthesis had an average particle size of 30 to 70 nm.     

Preparation of nanocrystalline Fe-doped TiO<Subscript>2</Subscript> powders as a visible-light-responsive photocatalyst

Nanocrystalline Fe-doped TiO₂ powders were prepared using TiOSO₄, urea, and Fe(NO₃)₃ · 9H₂O as precursors through a hydrothermal method. The as-synthesized yellowish-colored powders are composed of anatase TiO₂, identified by X-ray diffraction (XRD). The grain size ranged from 9.7 to 12.1 nm, calculated by Scherrer’s method. The specific surface area ranged from 141 to 170 m²/g, obtained by the Brunauer–Emmett–Teller (BET) method. The transmission electron microscopy (TEM) micrograph of the sample shows that the diameter of the grains is uniformly distributed at about 10 nm, which is consistent with that calculated by Scherrer’s method. Fe³⁺ and Fe²⁺ have been detected on the surface of TiO₂ powders by X-ray photoelectron spectroscopy (XPS). The UV–Vis diffuse reflection spectra indicate that the light absorption thresholds of the Fe-doped TiO₂ powders have been red-shifted into the visible light region. The photocatalytic activity of the Fe-doped TiO₂ was evaluated through the degradation of methylene blue (MB) under visible light irradiation. The Fe-doped TiO₂ powders have shown good visible-light photocatalytic activities and the maximum degradation ratio is achieved within 4.5 h.     

Preparation and structural characterization of nanosized BiFe<Subscript>0.6</Subscript>Mn<Subscript>0.4</Subscript>O<Subscript>3</Subscript> as a novel material with high sensitivity towards LPG

Nanocrystalline BiFe_0.6Mn_0.4O₃ powders were synthesized by sol–gel citrate method and studied for gas sensing behavior to reducing gases such as LPG, CO, CH₄ and NH₃. The composition and the structure of the powders have been investigated by means of XRD and TEM. The result shows that the BiFe_0.6Mn_0.4O₃ powders have a rhombohedral distorted perovskite structure with an average crystallite size of 35–40 nm. The BiFe_0.6Mn_0.4O₃-based LPG sensor shows better sensitivity at an operating temperature of 250 °C. The dispersion of Pd on BiFe_0.6Mn_0.4O₃ in the ratio of 0.8 wt.% improved the sensitivity, selectivity and response time. In addition, it reduced the operating temperature from 250 to 210 °C for LPG sensor. The response time for LPG was less than 1 min.     

Synthesis of non-agglomerated Ba<Subscript>0.77</Subscript>Ca<Subscript>0.23</Subscript>TiO<Subscript>3</Subscript> nanopowders by a modified polymeric precursor method

In this work, we have studied the influence of the pH on the synthesis and structural properties of the Ba_0.77Ca_0.23TiO₃ nanopowders synthesized by a modified polymeric precursor method, in order to achieve non-agglomerated powders. Synthesis, morphology, thermal reactions, crystallite and average particle size of the synthesized powders were investigated through thermal analysis (DTA/TG), X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM) and Infrared spectroscopy. In summary, Ba_0.77Ca_0.23TiO₃ nanopowders were synthesized for the first time at a relative low temperature (500 °C). It was also found that the alkalinity and acidity of the solution presented a great influence on the powder properties. The best results were obtained from solutions with pH = 8.5 and 11 whose nanopowders presented weakly agglomerate, with homogeneous particle size and a narrow size distribution (30–40 nm). This behavior could be explained based on the FT-IR results in which it was possible to see the increased of the chelation in higher pHs.     

Structural evolution and magnetic properties of SrFe<Subscript>12</Subscript>O<Subscript>19</Subscript> nanofibers by electrospinning

The SrFe₁₂O₁₉/poly (vinyl pyrrolidone) (PVP) composite fiber precursors were prepared by the sol-gel assisted electrospinning with ferric nitrate, strontium nitrate and PVP as starting reagents. Subsequently, the M-type strontium ferrite (SrFe₁₂O₁₉) nanofibers were derived from calcination of these precursors at 750–1,000 °C.The composite precursors and strontium ferrite nanofibers were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy and vibrating sample magnetometer. The structural evolution process of strontium ferrite consists of the thermal decomposition and M-type strontium ferrite formation. After calcined at 750 °C for 2 h the single M-type strontium ferrite phase is formed by reactions of iron oxide and strontium oxide produced during the precursor decomposition process. The nanofiber morphology, diameter, crystallite size and grain morphology are mainly influenced by the calcination temperature and holding time. The SrFe₁₂O₁₉ nanofibers characterized with diameters of around 100 nm and a necklace-like structure obtained at 900 °C for 2 h, which is fabricated by nanosized particles about 60 nm with the plate-like morphology elongated in the preferred direction perpendicular to the c-axis, show the optimized magnetic property with saturation magnetization 59 A m² kg⁻¹ and coercivity 521 kA m⁻¹. It is found that the single domain critical size for these M-type strontium ferrite nanofibers is around 60 nm.     

Glycine-nitrate combustion synthesis of CeFeO<Subscript>3</Subscript>-based nanocrystalline powders

Glycine-nitrate combustion method was used to obtain powders based on CeFeO₃ nanocrystals with average crystallite size in the range from 33 ± 3 to 51 ± 5 nm. The influence exerted by parameters of the glycine-nitrate combustion process and, in particular, by the glycine-nitrate ratio (G/N) on the composition and crystallite size of the synthesis products was determined. The optimal G/N ratio at which nanocrystalline cerium orthoferrite is formed with the minimum amount of impurity phases Fe₂O₃ and CeO₂ was found to be 0.8. It was demonstrated that the composition of the starting solution affects the nature of the phase heterogeneity in the resulting product, crystallite size, and porosity of the nanocrystalline powders being formed. The patterns determined in the study make it possible to optimize the technology of nanocrystalline powders based on CeFeO₃ in order to obtain powders with prescribed phase composition and crystallite sizes to enable their use as a basis for photocatalytic materials.     

Preparation of nanocrystalline TiO<Subscript>2</Subscript> powders for photocatalytic oxidation of phenol

Nanocrystalline TiO₂ powders in the anatase, rutile, and mixed phases prepared by hydrolysis of TiCl₄ solution were of ultrafine size (<7.2 nm) with high specific surface areas in the range 167 to 388 m²/g. In the photocatalytic degradation of phenol as model reaction, the photocatalytic properties of TiO₂ nanoparticles were evaluated by use of UV–vis absorption spectroscopy and total organic carbon (TOC) content. The synthetic mixed-phase TiO₂ powder calcined at 400 °C had higher activity than pure anatase or rutile; it degraded more than 90% phenol to CO₂ (evaluated by TOC) after irradiation with near UV light for 90 min at a catalyst loading of 0.4 g/L. The TOC results indicated that rutile TiO₂ crystallites of particle size 7.2 nm resulted in much better photocatalytic performance than particles of larger size. This result suggested that some intermediates, not determined by UV–vis absorption spectroscopy, existed in the solution after the photocatalytic process over the rutile TiO₂ photocatalysts of larger crystallite size.     

Sintering behavior and ionic conductivity of Ce<Subscript>0.8</Subscript>Gd<Subscript>0.2</Subscript>O<Subscript>1.9</Subscript> with a small amount of MnO<Subscript>2</Subscript> doping

A 20% GdO_1.5 doped ceria solid solution with a small amount of MnO₂ doping (≤5% molar ratio) was prepared via the mixed oxide method from high-purity commercial powders with grain size around 0.2–0.5 μm. X-ray diffraction analysis indicated that all the samples exhibited the fluorite structure, and no new phase was found. The data from dilatometeric measurements and scanning electron microscopy observations revealed that 1% Mn doping reduced the sintering temperature by over 150 °C, and enhanced the densification and grain growth. Mn doping has little effect on grain interior conductivity, but a marked deterioration in grain boundary behavior is observed. This leads to a lower total conductivity in comparison with the undoped Ce_0.8Gd_0.2O_2–δ. Therefore, for solid oxide fuel cells (SOFCs) with Mn-containing compounds as electrodes, optimization of electrode fabrication conditions is needed to prevent the formation of a lower conductivity layer at the electrode/electrolyte interface since Mn will diffuse from the electrode side to the electrolyte during fabrication and operation of SOFCs. Electronic Publication     

Hydrothermal synthesis of (Fe,N) co-doped TiO<Subscript>2</Subscript> powders and their photocatalytic properties under visible light irradiation

(Fe, N) co-doped titanium dioxide powders have been prepared by a quick, low-temperature hydrothermal method using TiOSO₄, CO(NH₂)₂, Fe(NO₃)₃, and CN₃H₅ · HCl as starting materials. The synthesized powders were characterized by XRD, TEM, BET, XPS, and UV–Vis spectroscopy. Experimental results show that the as-synthesized TiO₂ powders are present as the anatase phase and that the N and Fe ions have been doped into the TiO₂ lattice. The specific surface area of the powders is 167.8 m²/g by the BET method and the mean grain size is about 11 nm, calculated by Scherrer’s formula. UV–Vis absorption spectra show that the edge of the photon absorption has been red-shifted up to 605 nm. The doped titanium dioxide powders had excellent photocatalytic activity during the process of photo-degradation of formaldehyde and some TVOC gases under visible light irradiation.     

Synthesis of highly dispersed super-refractory tantalum-zirconium carbide Ta<Subscript>4</Subscript>ZrC<Subscript>5</Subscript> and tantalum-hafnium carbide Ta<Subscript>4</Subscript>HfC<Subscript>5</Subscript> via sol-gel technology

Nanocrystalline powders of super-refractory complex carbides Ta₄HfC₅ and Ta₄ZrC₅ were synthesized using a hybrid method comprising sol-gel technology for preparing highly dispersed metal oxidescarbon starting mixtures and a relatively low-temperature (1300–1500°C) carbothermal synthesis under a dynamic vacuum (P = 1 × 10⁻³ to 1 × 10⁻⁵ MPa). The elemental and phase compositions of the products and average crystallite sizes were determined. TEM was used to study particle morphology and dispersion. Microstructures were observed by SEM. BET specific surface areas were determined for powders prepared at 1400°C.     

Citrate-gel synthesis and characterization of yttrium-doped multiferroic BiFeO<Subscript>3</Subscript>

Perovskite Bi_1−x Y _x FeO₃ (0.0 ≤ x ≤ 0.1) oxides were prepared by a citrate-gel method. The crystal structure examined by X-ray powder diffraction indicates that the samples were single-phase and crystallize in a rhombohedral (space group, R-3c no. 161) structure. The structural phase transition from rhombohedral to orthorhombic phase was observed at x = 0.10. Increase in magnetization was observed as a result of Y doping. The optical band-gap of (Bi, Y)FeO₃ materials were determined. The observed increase in magnetization and low band-gap of (Bi, Y)FeO₃ ceramics position them for potential magenotoelectric and photocatalytic applications, respectively.     

Rapid synthesis of DyFeO<Subscript>3</Subscript> nanopowders by auto-combustion of carboxylate-based gels

EDTA and citric acid as two typical chelating reagents with multi-carboxyl groups were used to prepare DyFeO₃ nanopowders, respectively. The experimental results show that all of the carboxylate-based gels exhibited auto-propagating combustion behaviors. The XRD results indicate that DyFeO₃ single phase can be formed directly with CA/MN (citric acid to metal nitrate mole ratio) = 1 when the calcination temperature was above 700 °C. The specimen with EA/MN (EDTA to metal nitrate mole ratio) = 1 had the minimum crystallite size of 33 nm. The SEM images show that the as-burnt powders prepared with EDTA had more excellent dispersibility feature and clearer grain boundaries than that of citric acid. The magnetic measurement results show that DyFeO₃ nanopowders displayed antiferromagnetism characteristics at low temperatures due to the strong exchange interaction between Fe sublattice. As the ambient temperature increased, there was a transition from antiferromagnetism to paramagnetism in DyFeO₃ nanopowders.     

Thermal analysis and structural characterization of Bi<Subscript>4</Subscript>V<Subscript>2–x</Subscript>Ba<Subscript>x</Subscript>O<Subscript>11–1.5x</Subscript> (0.02≤<Emphasis Type="Italic">x</Emphasis>≤0.50)

This work reports the study of Bi₄V_2–xBa_xO_11–1.5x (0.02≤x≤0.50) series, which is a potential source of solid electrolytes to apply in oxygen sensors. X-ray powder diffraction was used to point out the formation of major ionic conductive phases and minor ones. The modifications of vanadate substructure were probed, at short range, by Fourier-transform infrared spectroscopy. Differential scanning calorimetry evidenced the formation of tetragonal γ phase, which can be ionic conductive, for x=0.14.     

Formation and properties of the Fe<Subscript>8</Subscript>V<Subscript>10</Subscript>W<Subscript>16–x</Subscript>Mo<Subscript>x</Subscript>O<Subscript>85</Subscript> type solid solution

Solid solution phases of a formula Fe₈V₁₀W_16–xMo_xO₈₅ where 0≤x≤4, have been obtained, possessing a structure of the compound Fe₈V₁₀W₁₆O₈₅. It was found on the base of XRD and DTA investigations that these solution phases melted incongruently, with increasing the value of x, in the temperature range from 1108 (x=0) to 1083 K (x=4) depositing Fe₂WO₆ and WO₃. The increase of the Mo⁶⁺ ions content in the crystal lattice of Fe₈V₁₀W₁₆O₈₅ causes the lattice parameters a=b contraction with cbeing almost constant. IR spectra of the Fe₈V₁₀W_16–xMo_xO₈₅ solid solution phases have been recorded.     

Steric distortion of planar NiP<Subscript>2</Subscript>N<Subscript>2</Subscript> chromophores: a spectral,cyclic voltammetric and single crystal X-ray structural study

The complexes trans-[Ni(4-MP)₂(NCS)₂]·MeCN (1) and trans-[Ni(3-MP)₂(NCS)₂] (2) (4-MP = tri(4-methylphenyl)phosphine, 3-MP = tri(3-methylphenyl)phosphine) were prepared and characterized by IR, UV–visible, NMR spectra, CV, TGA and single crystal X-ray crystallography. Both the complexes have planar geometry and are diamagnetic. The Ni–P distances in both complexes are relatively short as a result of strong back donation from nickel to phosphorus. The phenyl rings in the 3-MP analogue (2) show increased pitching with reference to the plane formed by the ipso carbons due to increased steric effects. For complex (2), the N–Ni–N and P–Ni–P angles are significantly lower than the almost linear N–Ni–N and N–Ni–P angles observed for both complex (1) and trans-[Ni(PPh₃)₂(NCS)₂]. This observation indicates that the 3-methylphosphine ligand forces complex (2) to distort towards a tetrahedral geometry. IR spectra of both complexes show strong bands around 2,090 cm⁻¹ due to N-coordinated thiocyanate, while the electronic spectra contain d–d transitions around 452 nm. Cyclic voltammograms show that the irreversible one-electron reduction potentials increase in the following order: trans- [Ni(PPh₃)₂(NCS)₂] < trans- [Ni(3-MP)₂(NCS)₂] < trans-[Ni(4-MP)₂(NCS)₂], revealing the electron releasing effect of the methyl groups. The planar complexes exhibit interallogony in coordinating solvents.     

Sol–gel synthesis and characterization of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–TiO<Subscript>2</Subscript> nanocrystalline powder

Al₂O₃–TiO₂ nanocrystalline powders were synthesized by sol–gel process. Aluminum sec-butoxide and titanium isopropoxide chemicals were used as precursors and ethyl acetoacetate was used as chelating agent. Thermal and crystallization behaviors of the precursor powders were investigated by thermal gravimetric-differential thermal analysis, Fourier-transform infrared spectrum and X-ray diffraction. The average crystalline size of heat treated Al₂O₃–TiO₂ powders at 1,100 °C is ~100 nm.     

An aqueous solution-gel method for low temperature synthesis of nanocrystalline NaNbO<Subscript>3</Subscript> and their ceramics

Nano-sized NaNbO₃ powder has been successfully prepared by aqueous solution-gel method. The phase evolution of NaNbO₃ powder is investigated by TG/DSC, X-rays spectra, FT-IR, and Raman spectra. The results show that the pure NaNbO₃ phase has been obtained at about 375 °C, which is lowered by about 100 °C comparing to others’ work. In TEM studied, it shows the average particle size of ~ 70 nm for the powders heat-treated at 750 °C for 4 h. The powders heat-treated below 650 °C for 4 h shows a Pmnm symmetry, then change from O₃ orthorhombic to O₁ orthorhombic with the heat-treatment temperature above 650 °C.     

Electrochemical performance of rare-earth doped LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> spinel cathode materials for Li-ion rechargeable battery

Spinel powders of LiMn_2−x RE _x O₄ (RE = La, Ce, Nd, Sm; 0 ≤ x ≤ 0.1) have been synthesized by solid-phase reaction. The structure and electrochemical properties of these electrode materials were characterized by X-ray diffraction (XRD), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and charge–discharge experiment. The part substitution of rare-earth element RE for Mn in LiMn₂O₄ decreases the lattice parameter, resulting in the improvement of structural stability, and decreases the charge transfer resistance during the electrochemical process of LiMn₂O₄. As a result, the cycle ability, 55 °C high-temperature and high-rate performances of LiMn_2−x RE _x O₄ electrode materials are significantly improved with increasing RE addition, compared to the pristine LiMn₂O₄.     

2-pyrrolidone - capped Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> nanocrystals

Water-soluble Mn₃O₄ nanocrystals have been prepared through thermal decomposition in a high temperature boiling solvent, 2-pyrrolidone. The final product was characterized with XRD, SEM, TEM, FTIR and Zeta Potential measurements. Average crystallite size was calculated as ∼15 nm using XRD peak broadening. TEM analysis revealed spherical nanoparticles with an average diameter of 14±0.4 nm. FTIR analysis indicated that 2-pyrrolidone coordinates with the Mn₃O₄ nanocrystals only via O from the carbonyl group, thus confining their growth and protecting their surfaces from interaction with neighboring particles.