Design and performance analysis of a nanogyroscope based on electrostatic actuation and capacitive sensing

In this paper, a vibrating beam gyroscope with high operational frequencies at mode-matched condition is proposed. The model comprises a micro-cantilever with attached tip mass operating in the flextural–flextural mode. The drive mode is actuated via the electrostatic force, and due to the angular rotation of the base about the longitudinal axis. The secondary sub-nanometric vibration is induced in the sense direction which causes a capacitive change in the sense electrodes. The coupled electro-mechanical equation of motion is derived using the extended Hamilton's principle, and it is solved by direct numerical integration method. The gyroscope performance is investigated through the simulation results, where the device dynamic response, rate sensitivity, resolution, bandwidth, dynamic range, g$g$ sensitivity and shock resistance are studied. The obtained results show that the proposed device may have better performance compared to commercial micro electromechanical gyroscope characteristics.     

Bifurcations and loss of orbital stability in nonlinear viscoelastic beam arrays subject to parametric actuation

The collective dynamic response of microbeam arrays is governed by nonlinear effects, which have not yet been fully investigated and understood. This work employs a nonlinear continuum-based model in order to investigate the nonlinear dynamic behavior of an array of N nonlinearly coupled micro-electromechanical beams that are parametrically actuated. Investigations focus on the behavior of small size arrays in the one-to-one internal resonance regime, which is generated for low or zero DC voltages. The dynamic equations of motion of a two-element system are solved analytically using the asymptotic multiple-scales method for the weakly nonlinear system. Analytically obtained results are verified numerically and complemented by a numerical analysis of a three-beam array. The dynamic responses of the two- and three-beam systems reveal coexisting periodic and aperiodic solutions. The stability analysis enables construction of a detailed bifurcation structure, which reveals coexisting stable periodic and aperiodic solutions. For zero DC voltage only quasi-periodic and no evidence for the existence of chaotic solutions are observed. This study of small size microbeam arrays yields design criteria, complements the understanding of nonlinear nearest-neighbor interactions, and sheds light on the fundamental understanding of the collective behavior of finite-size arrays.     

光时分复用(OTDM)系统中基于电吸收调制器(EAM)的短脉冲光源及解复用器的设计考虑

研究了电吸收调制器（ＥＡＭ） 的衰减随外加反向电压增加而指数增加的情形下,短脉冲光源的脉冲输出和解复用器的开关窗口对ＥＡＭ 的消光效率、反向ＤＣ 偏置电压以及正弦ＲＦ 驱动信号的幅度等参量的依赖关系－ 在基于ＥＡＭ 的短脉冲光源中,输出脉冲的消光比等于ＥＡＭ 消光效率η与正弦驱动电压峰峰值Ｖｐｐ 的乘积,输出光脉冲的消光比和脉宽均与ＥＡＭ 的反向偏置电压无关,但输出脉冲的峰值功率与η、Ｖｐｐ 和Ｖｂ 都有关系－ 在基于ＥＡＭ的解复用器中,为了使解复用器的开关窗口近似为矩形,可利用ＥＡＭ 的削波效应,使Ｖｐｐ／２＞ Ｖｂ－ 在ＥＡＭ 的消光效率η已知时,通过仔细设计反向ＤＣ 偏置电压Ｖｂ 和正弦驱动电压的峰峰值Ｖｐｐ ,达到ＯＴＤＭ 解复用器所需要的开关窗口形状、宽度和消光比－     

Measurement and simulation of partial discharge in oil-paper insulation under the combined AC–DC voltage

Depending on unique operation characteristics for voltage applied on valve side winding of the converter transformers, it is extraordinarily significant to study the partial discharge (PD) behavior with oil-paper insulation under combined AC–DC voltage. Therefore, this paper investigated PD inception characteristics by pulse current methods with needle-plate electrode system under combined AC–DC voltage. Furthermore, 3D electric field distributions versus combined AC–DC voltage in different ratios were calculated by Finite Element Analysis (FEA). An experimental conclusion was drew that AC partial discharge inception voltage (PDIV) in pure oil would decrease linearly with the DC component increasing but the inception voltage with oil-paper insulation appeared to be independent of DC voltage and dependent of AC voltage. And 3D electric field distribution deduced from simulation provided a supplementary proof on the experimental results. Moreover, high speed photography was used to capture emitted light produced by discharge, estimate streamer velocity (1.8 km/s) and record streamer initiation and propagation process in oil gap. Previous studies have shown that the prebreakdown phenomena involving the generation and propagation of vapor channels through the oil could be divided into a three-stage process.     

γ谱仪测量系统样品旋转装置研制

利用球体随机旋转性好的特点，将包装样品的容器装入球内并放在样品旋转台中，在两台速度不同，方向垂直的步进电机带动下，球在旋转台上随机转动，实现对包装容器内的样品进行连续随机扫描，以达到减小由于包装容器的非均匀性对测量结果的影响，样品旋转装置由球面板、四根支柱，底座、步进电机及步进电机控制电路组成。采用两台型号为５７ＢＹＧ５０３的步进电机驱动球体旋转，步进电机控制器可对两台电机进行单独控制，并具有正反转功能，其转速分为２、５、８、１２、１６、２０转／ｍｉｎ六档，可连续长时间工作。     

Vibrations of narrow microbeams predeformed by an electric field

Vibrations of a fixed–fixed narrow microbeam electrostatically actuated by applying a voltage difference to it and a parallel rigid conductor are analyzed. For gaps between the two conductors that are comparable to the beam's thickness, the fundamental frequency of the beam may first increase with increasing applied voltage, before suddenly dropping at the pull-in voltage. Available models fail to accurately describe this behavior of the frequency versus voltage diagram for narrow microbeams, that results from a combination of strain-hardening and electrostatic softening effects. A distributed electromechanical model, that accounts for electrostatic fringing fields, finite deflections and residual stresses, is proposed. A recent estimate of the electrostatic force incorporating fringing fields due to both finite width and finite thickness of the microbeam is employed. The lowest frequency is extracted with a simple and computationally efficient one degree-of-freedom model obtained by approximating the deflection field with the static deflection of a fixed–fixed microbeam loaded by a uniformly distributed force. The model's predictions are in good agreement with those from three-dimensional finite-element simulations.     

Influence of additives blended with motor base oils on the braking torque under an auxiliary external DC electric field

The paper presents the results of experiments upon the influence of tribocharging of PAO and PAG synthetic motor base oils blended with different additives—friction modifiers (FM) and antiwear agents (AW)—and the effect of an external DC electric field on the braking torque. The experiments are carried out in a rotating shaft–oil–lip seal system which represents a specially built experimental facility to be a simplified model of an engine crankcase in the interior of which a metal shaft rotates. The research is especially aimed at the braking torque of a rotating shaft sealed with a lip seal and a possibility of reduction in the torque under external DC electric fields. DC voltage is applied between the stiffening ring of lip seal and a rotating, earthed shaft. The braking torque of rotating shaft is measured as a function of the oil–additive blend's temperature, the shaft's angular velocity, and the absolute value of the external DC voltage. In general, it is found that an external DC electric field causes the braking torque to change with the increasing DC voltage. The change depends on the additives and base oils used in their blends which in turn causes the torque to increase in the case of the PAO–additive blends or to decrease for the PAG–additive blends.     

微型无刷直流电机位置系统的过程控制

为了实现机械相控阵列天线的波束扫描,采用微型无刷直流电机驱动螺旋天线单元转动来到达预定的辐射相位。设计了一种新型微型无刷直流电机位置控制系统,构建了比例滑模面-超螺旋二阶滑模控制器用于速度控制,利用结合速度剖面策略的PID控制算法实现了转动位置的中间过程控制。建立了基于Simulink的系统仿真模型,验证了方案的可行性,并构建了FPGA硬件实验平台。仿真和实验结果均表明,微型无刷直流电机驱动天线单元精确按照预设的速度剖面曲线运行,在50 ms控制周期内转动角度达到180°,中间控制过程的位置跟踪误差和平衡位置处的残余震荡误差均小于±3°。     

光时分复用(OTDM)系统中基于电吸收调制器(EAM)的短脉冲光源及解复用器的设计考虑

研究了电吸收调制器(EAM)的衰减随外加反向电压增加而指数增加的情形下,短脉冲光源的脉冲输出和解复用器的开关窗口对EAM的消光效率、反向DC偏置电压以及正弦RF驱动信号的幅度等参量的依赖关系.在基于EAM的短脉冲光源中,输出脉冲的消光比等于EAM消光效率η与正弦驱动电压峰峰值V_pp的乘积,输出光脉冲的消光比和脉宽均与EAM的反向偏置电压无关,但输出脉冲的峰值功率与η、V_pp和V_b都有关系.在基于EAM的解复用器中,为了使解复用器的开关窗口近似为矩形,可利用EAM的削波效应,使V_pp/2>V_b.在EAM的消光效率η已知时,通过仔细设计反向DC偏置电压V_b和正弦驱动电压的峰峰值V_pp,达到OTDM解复用器所需要的开关窗口形状、宽度和消光比.     

Comparison of modeling of the rotating tapered axially functionally graded Timoshenko and Euler–Bernoulli microbeams

The target of this paper is to present an exhaustive study on the small scale effect on vibrational behavior of a rotary tapered axially functionally graded (AFG) microbeam on the basis of Timoshenko and Euler–Bernoulli beam and modified couple stress theories. The variation of the material properties and cross section along the longitudinal direction of the microbeam are taken into consideration as a linear function. Hamilton's principle is used to derive the equations for cantilever and propped cantilever boundary conditions and the generalized differential quadrature method (GDQM) is employed to solve the equations. By parametric study, the effects of small-scale parameter, rates of cross section change of the microbeam and angular velocity on the fundamental and second frequencies of the microbeam are studied. Also, comparison between the frequencies of Timoshenko and Euler–Bernoulli microbeams are presented. The results can be used in many applications such as micro-robots and biomedical microsystems.     

Magnetotransport properties of patterned magnetic Ni wires of submicrometric dimensions

Submicrometric Ni wires have been obtained by electron beam lithography to study their magnetic behavior by magnetotransport measurements. The magnetization reversal of these patterned nanostructures is driven by a combination of two mechanisms: coherent rotation processes, that govern the rotation when the magnetization direction of the lines is away from wire axis, and incoherent curling mechanisms that drive the reversal when the magnetization is closely parallel to line direction.     

HEAT TRANSFER IN HIGH-PRESSURE COMPRESSOR GAS TURBINE INTERNAL AIR SYSTEMS: A ROTATING DISC-CONE CAVITY WITH AXIAL THROUGHFLOW

This article reports on heat transfer measurements made on a rotating test rig representing the internal disc-cone cavity of a gas turbine high-pressure (H.P.) compressor stack. Tests were carried out for a range of flow rates and rotational speeds at engine representative nondimensional conditions. The rig also had a central drive shaft, which could rotate in the same direction as the discs, contrarotate relative to the discs, or remain static. Measurements of heat transfer were obtained from a conduction solution method using measured surface temperatures as boundary conditions. Results from the outer surface of the cone are in reasonable agreement with theoretical predictions for the heat transfer from a free cone in turbulent flow. The heat transfer measurements from the inner surface of the cone reveal two regimes of heat transfer: one governed by rotation, the other by action of the throughflow. In the rotationally dominated regime, the heat transfer from the inner surface of the cone is higher for a co-rotating shaft than for either a static or contra-rotating shaft. In the throughflow-dominated regime the heat transfer shows little consistent dependence on the direction of shaft rotation. Tests carried out at different values of surface-to-fluid temperature difference add support to the hypothesis that in the rotationally dominated regime the heat transfer occurs through a process of free convection, where the buoyancy force is induced by rotation. The heat transfer from the disc is significantly lower than that from the inner surface of the cone and more or less insensitive to the sense of shaft rotation. The disc average Nusselt numbers show similar behavior to those from the inner surface of the cone and suggest that the disc heat transfer too is governed either by rotationally induced buoyancy or by the axial throughflow.     

GaN基高压直流发光二极管制备及其性能分析

GaN基高压直流发光二极管工艺制备, 采用蓝宝石图形衬底(PSS) 外延片制备正梯形芯粒结构的GaN基高压直流LED.相对其他结构器件, 该结构器件发光效率最高, 封装白光后, 在色温4500 K, 驱动电流20 mA时, 光效116.06 lm/W, 对应电压50 V. 测试其I-V曲线表明, 开启电压为36 V, 对应驱动电流为1.5 mA; 在电流15 mA至50 mA时, 光功率随驱动电流增加近似于线性增加, 在此区域光效随电流增加而降低的幅度比较缓慢, 表明GaN基高压直流LED适宜于采用大电流密度驱动, 而不会出现驱动电流密度增加导致量子效率明显下降(efficiency droop), 为从芯片层面研究解决量子效率下降难题提供了一种新思路.     

Lateral IBIC characterization of single crystal synthetic diamond detectors

In order to evaluate the charge collection efficiency (CCE) profile of single‐crystal diamond devices based on a p‐type/intrinsic/metal configuration, a lateral Ion Beam Induced Charge (IBIC) analysis was performed over their cleaved cross sections using a 2 MeV proton microbeam. CCE profiles in the depth direction were extracted from the cross‐sectional maps at variable bias voltage. IBIC spectra relevant to the depletion region extending beneath the frontal Schottky electrode show a 100% CCE, with a spectral resolution of about 1.5%. The dependence of the width of the high efficiency region from applied bias voltage allows the constant residual doping concentration of the active region to be evaluated. The region where the electric field is absent shows an exponentially decreasing CCE profile, from which it is possible to estimate the diffusion length of the minority carriers by means of a drift–diffusion model. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Corona-discharge-based neutralization of charged granular insulating materials in contact with an electrode of opposite polarity

Charge neutralization is a key operation in many electrostatic processes. A wide-range of charge neutralizers have already been developed for various applications: eliminate shock and ignition hazards, avoid electrostatic discharges that might affect the operation of electronic equipment, reduce electrostatic adhesion forces that might stick granular materials in pneumatic conveyors, and so on. The aim of the present paper is to evaluate several methods of charge neutralization for charged granular insulating materials spread on an electrode energized from a voltage source of opposite polarity, a situation encountered – for instance – in two-metallic-belt tribo-aero-electrostatic separators, and which is not covered by commercially-available solutions. Three corona-discharge-based charge neutralization systems are studied: (i) DC-biased AC voltage applied to a corona dual-type electrode; (ii) DC-biased AC voltage applied to a triode-type electrode system; (iii) DC voltage applied to a corona dual-type electrode. The charged samples of polycarbonate granules are obtained at the outlet of a tribo-aero-electrostatic separator. The electric charge per mass ratio of each sample is measured before and after neutralization. The third of the above-mentioned charge neutralization solutions seems to be the most effective solution, but it requires an appropriate adjustment of the DC voltage applied to the corona dual-type electrode.     

Reciprocity of Faraday effect in ferrofluid: Comparison with magneto-optical glass

The transmission light intensity method is carried out on a classical platform to study the reciprocity of Faraday effect in water-based Fe₃O₄ ferrofluid and its diluents. Setting the polarization direction of the analyzer at an angle of 45° to that of the polarizer, the switchable DC magnetic field and the alternating magnetic field are imposed to ferrofluid. The ferrofluid film is replaced by magneto-optical glass for contrastive experiments. The results indicate that ferrofluid is different with magneto-optical glass. Even though the direction of magnetic field is reversed, the rotation direction of the polarized light does not change for ferrofluid. The theoretical model of magneto-optical rotation was used to describe the origin of the reciprocity of Faraday effect in ferrofluid and the non-reciprocity in magneto-optical glass. These findings suggest that the magnetic moments of nanoparticles in ferrofluid tend to the same orientation with the magnetic field because of the rotation of particles.     

Characterization of multilayered piezoelectric ceramics for high power transducers

In some circumstances, large vibrational displacements at ultrasonic frequency must be generated using a low voltage drive. This result cannot be obtained with monolithic PZT ceramics which require voltages larger than 1000 V to produce displacements of the micrometer order at resonance. The use of multilayered hard lead zirconate titanate ceramics as transduction material in resonant devices is experimentally investigated for Langevin-type transducers. Large amplitudes are obtained under low drive (5 microm under 10 V). Material constant (compliance, losses) variations under large dynamic stress are, at least, one order of magnitude larger than for monolithic ceramics. Depolarization is found to be a critical issue when the transducer is driven continuously. It is demonstrated that this problem can be solved by polishing the interfaces between different parts of the device and applying an electrical DC bias to the transducer.     

Flow rate increased by electrorotation in a capillary

In this paper, we show that the viscosity of a suspension can be drastically reduced if its particles are rotating faster than the surrounding liquid. We propose to induce particle rotation by applying a DC electric field to a suspension of insulating particles dispersed in a slightly conducting liquid (Quincke rotation). We have studied the flow of such a suspension in a rectangular channel and measure the increase of the flow rate induced by the application of an electric field along the velocity gradient direction (shortest dimension of the channel).     

基于DSP2808的轴流风机控制器设计

针对工业用轴流风机,设计了基于DSP2808的智能轴流风机控制器,给出了DSP系统、CPLD系统、驱动电路、功率电路、故障检测与保护电路、单端反激变换器的设计方案。分析了风机调节流量的方法,控制器能够根据温度反馈通过PWM斩波实现风机宽范围无级调速,实现节能;控制器能够接收外部电位计、温度传感器、485总线的转速给定,表决后产生最终的转速给定;控制器具备电机绕组过热、IGBT过热、交流侧过欠压、直流侧过欠压、直流侧过流等故障检测与保护功能。实验结果表明：控制器能够实现风机匀加速软起动及起动与转速闭环之间的平稳过渡,有效降低了风机启动、运行过程的噪声,同时实现了节能。     

Modelling and characterization of a piezoceramic inertial actuator

An inertial actuator (also known as a proof mass actuator) applies forces to a structure by reacting them against an “external” mass. This approach to actuation may provide some practical benefits in the active control of vibration and structure-borne noise: system reliability may be improved by removing the actuator from a structural load path; effective discrete point-force actuation permits ready attachment to curved surfaces, and an inherent passive vibration absorber effect can reduce power requirements.This paper describes a class of recently developed inertial actuators that is based on mechanical amplification of displacements of an active piezoceramic element. Important actuator characteristics include resonance frequencies, clamped force, and the drive voltage to output the force frequency response function.The paper addresses one particular approach to motion amplification, the “dual unimorph,” in detail. A model of actuator dynamic behavior is developed using an assumed-modes method, treating the piezoelectrically induced stresses as external forces. Predicted actuator characteristics agree well with experimental data obtained for a prototype actuator. The validated actuator dynamic model provides a tool for design improvement.