40Cr材料动态起裂韧性KId（）的实验测试

描述了利用Ｈｏｐｋｉｎｓｏｎ压杆技术加载三点弯曲试样测试４０Ｃｒ，材料动态起裂韧性ＫＩｄ（）的试验方法。试样上的动态载荷历程由Ｈｏｐｋｉｎｓｏｎ杆直接测得，并分别代入动态有限元程序及近似公式求得动态应力强度因子历史；由贴在试样裂尖附近的应变片确定起裂时间，最终确定起裂时的动态应力强度因子值，即动态起裂韧性ＫＩｄ（）。试验结果表明:利用Ｈｏｐｋｉｎｓｏｎ压杆技术加载三点弯曲试样测试材料动态起裂韧性的方法是可行的，起裂时，动态有限元的位移法、应力法及近似公式法求得的动态应力强度因子值比较吻合；在本文的载荷速率下，４０Ｃｒ材料动态起裂韧性ＫＩｄ（）与准静态裂韧性ＫＩｄ（）相比，降低了约２８％。     

Dynamic mechanical and fracture properties of an infiltrated TiC-1080 steel cermet

The dynamic mechanical and fracture properties of a TiC porous network infiltrated with1080 steel are reported. Following infiltration, the cermet is subjected to various heat treatments that affect essentially the steel matrix. Dynamic compression tests show that the heat treatments increase the fracture strength of the cermet. The quasi-static fracture toughness (K_Ic) is also increased by the heat treatments. The dynamic (initiation) fracture toughness (K_Id) is substantially higher (by about a factor of 3) than its static counterpart. Failure mechanisms consist mainly of cleavage of the TiC and matrix grains, along with minor interfacial decohesion. However, dynamic loading induces substantial damage around the crack tip, consisting essentially of cleavage of TiC grains. Microcrak toughnening is believed to be responsible for the high dynamic toughness of the material. The critical microstructural fracture event is thus identified as the spreading of TiC cleavage microcracks into the neighboring steel grains.     

Fracture initiation associated with chemical degradation: observation and modeling

The fracture initiation in engineering thermoplastics resulting from chemical degradation is usually observed in the form of a microcrack network within a surface layer of degraded polymer exposed to a combined action of mechanical stresses and chemically aggressive environment. Degradation of polymers is usually manifested in a reduction of molecular weight, increase of crystallinity in semi crystalline polymers, increase of material density, a subtle increase in yield strength, and a dramatic reduction in toughness. An increase in material density, i.e., shrinkage of the degraded layer is constrained by adjacent unchanged material results in a buildup of tensile stress within the degraded layer and compressive stress in the adjacent unchanged material due to increasing incompatibility between the two. These stresses are an addition to preexisting manufacturing and service stresses. At a certain level of degradation, a combination of toughness reduction and increase of tensile stress result in fracture initiation. A quantitative model of the described above processes is presented in these work. For specificity, the internally pressurized plastic pipes that transport a fluid containing a chemically aggressive (oxidizing) agent is used as the model of fracture initiation. Experimental observations of material density and toughness dependence on degradation reported elsewhere are employed in the model. An equation for determination of a critical level of degradation corresponding to the offset of fracture is constructed. The critical level of degradation for fracture initiation depends on the rates of toughness deterioration and build-up of the degradation related stresses as well as on the manufacturing and service stresses. A method for evaluation of the time interval prior to fracture initiation is also formulated.     

采用压缩单裂纹圆孔板确定岩石动态起裂、扩展和止裂韧度

爆炸、冲击、地震等人为或自然灾害不可避免,经常造成大量土木工程设施的破坏,因此岩石在动态载荷作用下的行为受到特别关注.岩石动态断裂韧度是评价岩石抵抗裂纹动态起裂、扩展和止裂性能的材料参数,开展岩石动态断裂韧度测试方法的研究对相关理论基础和实验技术的要求较高.岩石动态断裂韧度分为动态起裂、动态扩展、动态止裂三种,虽然关于动态起裂和动态扩展的研究已有一些成果,对岩石动态止裂的研究仍是一个难题,至今几乎无人问津.研究表明,在分离式霍普金森压杆撞击压缩单裂纹圆孔板岩石试样的I型动态断裂试验中,动态起裂、扩展、止裂的全过程可以由黏贴在压缩单裂纹圆孔板试样上的裂纹扩展计监测,岩石的动态起裂、扩展、止裂韧度可以用实验-数值-解析法确定.特别值得一提的是首次测出了岩石的动态止裂韧度.裂纹扩展计信号还显示,压缩单裂纹圆孔板在止裂后,停止的裂纹还会再次动态起裂、扩展并超出裂纹扩展计的检测范围.从能量的角度分析了动态止裂的过程,指出测试动态止裂韧度时要注意的一些问题.结果显示,岩石动态起裂韧度和动态扩展韧度分别随动态加载率和裂纹扩展速度的增大而增大,岩石动态起裂韧度略大于动态止裂韧度.      

超细晶D6A钢动态拉伸力学特性实验研究

为了推进超细晶D6A钢在半穿甲战斗部壳体上的应用,研究了动态加载下其宏观力学行为和细观变形机理。运用旋转盘式Hopkinson拉杆技术,开展了超细晶D6A低合金钢（平均晶粒尺寸为510 nm）的动态拉伸实验,获得了不同应变率（500～1000 s?1）下超细晶钢的应力-应变曲线。运用TEM观测微观形貌,从细观层次研究了高应变率拉伸作用下超细晶钢的动态力学特性。结果表明,超细晶D6A钢具有较高的动态拉伸强度和良好的延展性。并且,晶粒细化和纳米析出相（渗碳体）是超细晶钢同时拥有高强度和较好韧性的重要因素;在动态拉伸过程中析出的大量纳米级渗碳体,与高密度晶界共同作用限制了位错运动,从而产生额外的塑性变形抗力,有效提升了超细晶钢的强度;在塑性变形阶段超细晶钢出现的明显应力下降现象,是可动位错密度增高的结果。     

冲击载荷作用下黑砂岩动态断裂参数的分形修正

基于分形理论研究了偏折裂纹扩展路径对动载荷作用下黑砂岩的动态断裂力学参数的测试误差影响作用,采用传统的分离式霍普金森压杆（split Hopkinson pressure bar, SHPB）实验装置对修正侧开单裂纹半孔板（improved single cleavage semi-circle specimen, ISCSC）试样进行动态冲击实验,随后采用裂纹扩展计进行裂纹起裂时间与裂纹扩展速度等动态断裂力学参数测试,采用分形理论对测试的裂纹扩展速度与动态应力强度因子进行修正,利用实验-数值法对黑砂岩的动态断裂韧度进行计算。研究结果表明,ISCSC构型构件能够有效应用于岩石材料动态裂纹扩展行为的研究,并发生了止裂现象,经分形修正的裂纹扩展速度与动态断裂韧度更接近实际裂纹动态扩展情况,修正前后得到黑砂岩材料的裂纹扩展速度误差为33.51%,动态断裂韧度最大误差为7.68%,说明利用分形理论对动态断裂韧度等动态断裂参数计算更合理。     

Dynamic toughness in elastic nonlinear viscous solids

This work addresses the interrelationship among dissipative mechanisms—material separation in the fracture process zone (FPZ), nonelastic deformation in the surrounding background material and kinetic energy—and how they affect the macroscopic dynamic fracture toughness as well as the limiting crack speed in strain rate sensitive materials. To this end, a micromechanics-based model for void growth in a nonlinear viscous solid is incorporated into a microporous strip of cell elements that forms the FPZ. The latter is surrounded by background material described by conventional constitutive relations. In the first part of the paper, the background material is assumed to be purely elastic. Here, the computed dynamic fracture toughness is a convex function of crack velocity. In the second part, the background material as well as the FPZ are described by similar rate-sensitivity parameters. Voids grow in the strain rate strengthened FPZ as the crack velocity increases. Consequently, the work of separation increases. By contrast, the inelastic dissipation in the background material appears to be a concave function of crack velocity. At the lower crack velocity regime, where dissipation in the background material is dominant, toughness decreases as crack velocity increases. At high crack velocities, inelastic deformation enhanced by the inertial force can cause a sharp increase in toughness. Here, the computed toughness increases rapidly with crack velocity. There exist regimes where the toughness is a non-monotonic function of the crack velocity. Two length scales—the width of the FPZ and the ratio of the shear wave speed to the reference strain rate—can be shown to strongly affect the dynamic fracture toughness. Our computational simulations can predict experimental data for fracture toughness vs. crack velocity reported in several studies for amorphous polymeric materials.     

动载下韧性撕裂在三种管线钢材中传播阻力的研究

阐述了用实验确定在常温及静载和动载条件下韧性撕裂在三种管线钢材中传播时的断裂比能值。实验中采用了销钉加载双面开槽的双悬脊梁(DCB)试件。应用能量平衡法对实验结果进行了分析。考察了加载速率和试件厚度对撕裂韧性的影响。结果表明,管线钢材对韧性撕裂传播的阻力在动载条件下增大,对较薄的试件及应变率敏感性较高的材料其增大更为明显。对于纯剪切断裂的传播来说,撕裂韧性一般随试件厚度的增大而增加。     

一种基于SHTB的Ⅱ型动态断裂实验技术

冲击剪切载荷作用下动态断裂韧性的测定是材料力学性能和断裂行为研究中重要组成部分.为了测定材料的Ⅱ型动态断裂韧性,许多学者采用不同的试样与实验方法进行了实验,但限于实验条件,裂纹断裂模式往往是I+Ⅱ复合型,而不是纯Ⅱ型,因而不能准确测得材料的Ⅱ型动态断裂韧性.鉴于此,本文基于分离式霍普金森拉杆(split Hopkinson tension bar,SHTB)实验技术,提出一种改进的紧凑拉伸剪切(modified compact tension shear,MCTS)试样,通过夹具对MCTS试样施加约束,从而保证试样按照纯Ⅱ型模式断裂.采用实验-数值方法对MCTS试样动态加载过程进行分析,将实验测得的波形输入有限元软件ANSYS-LSDYNA,得到了裂纹尖端应力强度因子-时间曲线,并与紧凑拉伸剪切(compact tension shear,CTS)试样进行了对比.同时采用数字图像相关法进行了实验,验证了有限元分析结果.结果表明,MCTS试样在整个加载过程中K_I K_Ⅱ,裂纹没有张开;而CTS试样在同样的加载过程中K_IK_Ⅱ,出现裂纹张开现象.这说明MCTS试样能够准确地测定材料的Ⅱ型动态断裂韧性,为材料动态力学测试提供了一种有效的实验技术.     

基于裂纹扩展脆性岩石动力压缩力学特性研究

动态压缩荷载作用下,脆性岩石内部动态细观裂纹扩展特性,对岩石宏观动态力学特性有着重要的影响。然而,对岩石内部动态细观裂纹扩展与宏观动态力学特性的关系研究较少。基于准静态裂纹扩展作用下的应力-应变本构模型、准静态与动态裂纹扩展断裂韧度关系、裂纹速率与应变率关系模型及应变率与动态断裂韧度关系,提出了一种基于细观力学的动态应力-应变本构模型。其中裂纹速率与应变率关系,是根据裂纹长度与应变关系的时间导数推出;应变率与动态断裂韧度关系,是根据推出的裂纹速率及应变率关系,与裂纹速率及断裂韧度关系相结合而得到。研究了应变率对应力-应变本构关系及动态压缩强度影响。并通过试验结果验证了模型的合理性。讨论了岩石初始损伤、围压、模型中参数m、ε0和R对应力-应变关系、动态压缩强度和动态弹性模量的影响。研究结果可为动态压缩荷载作用下深部地下工程脆性围岩稳定性分析提供了一定的理论支持。     

加载速率对40Cr钢Ⅱ型动态断裂特性的影响

采用新型Ⅱ型动态断裂测试技术,对高强钢40Cr在高加载速率下的Ⅱ型动态断裂特性进行了测试研究。基于新设计的Ⅱ型动态断裂试样和分离式霍普金森压杆（split Hopkinson pressure bar, SHPB）技术,通过实验-数值方法确定了裂尖在加载过程中的应力强度因子曲线。采用应变片法确定了试样的起裂时间,最终得到40Cr的Ⅱ型动态断裂韧性值,并对其加载速率相关性和材料的失效机理进行了研究。结果表明,在1.08～5.53 TPa·m1/2/s的加载速率范围内,40Cr的Ⅱ型动态断裂韧性基本表现为与加载速率成正相关的变化趋势。通过对试样断口形貌的分析,确定了材料的失效模式及机理,发现随着加载速率的增加,存在拉伸型失效向绝热剪切型失效模式转变的现象。     

加载速率和几何尺寸对国产A508-III钢断裂行为影响的实验研究

由加载速率和几何约束改变而引起的压力容器钢韧脆转变问题是核能安全领域亟待解决的关键问题. 为了准确分析国产A508-III钢的动态断裂行为, 借助INSTRON VHS高速材料试验机, 开展了不同加载速率和几何尺寸条件下的国产A508-III钢的断裂韧性试验, 研究了加载速率和几何尺寸等因素对国产A508-III钢动态断裂韧性的影响. 研究表明, A508-III钢具有良好的抗冲击韧性, 随着加载速率的提高, 试样的总冲击吸收能基本保持恒定, 裂纹萌生吸收能量不断上升, 而裂纹扩展吸收能量呈下降趋势. J-Δa阻力曲线和条件起裂韧性J_Q随着几何约束的增加而降低, 随加载速率的增加而升高. 当达到某一临界速率时, 条件起裂韧性J_Q基本恒定, 试样断裂方式也由韧性断裂转变为韧?脆?韧混合断裂. 由于出现混合断裂模式, 发生脆性断裂时的最大J积分值J_max更适于描述国产A508-III钢的断裂韧性演化规律. 随着试样面外几何约束的降低, J_max随Δa_m的增加而线性增大. 试样面内几何约束越高, J_max与Δa_m之间的线性关系斜率越大. 随着试样几何约束的增加, 材料的韧脆转变速率增加, J_max值下降. 改变几何约束只能在有限的加载速率范围内改变材料的断裂方式, 当加载速率超过某个临界值时, 加载速率成为影响材料断裂方式的主要因素.      

用短棒试件测试无烟煤的动态断裂韧度

介绍了设计的新型圆台式压头及配套的衬片加载部件,推导了采用新的加载部件进行冲击断裂实验时的断裂韧度计算公式。采用SHPB实验装置,用新加载部件对带有V形切口的无烟煤短棒试件的裂纹尖端施加拉伸载荷,测定了无烟煤的动态断裂韧度。结合准静态实验数据得到了无烟煤断裂韧度随加载率lg(dF/dt)的总体变化规律:当lg(dF/dt)6时,无烟煤的断裂韧度缓慢上升,但当lg(dF/dt)6以后,无烟煤的断裂韧度随加载率的增加快速增大。实验表明:圆台式加载比刀刃式加载更具优越性和适应性,是测试岩石类材料短棒试件动态断裂韧度较好的方法。     

A Semi-Circular Bend Technique for Determining Dynamic Fracture Toughness

We propose and validate a fracture testing method using a notched core-based semi-circular bend (SCB) specimen loaded dynamically with a modified split Hopkinson pressure bar (SHPB) apparatus. An isotropic fine-grained granitic rock, Laurentian granite (LG) is tested to validate this dynamic SCB method. Strain gauges are mounted near the crack tip of the specimen to detect the fracture onset and a laser gap gauge (LGG) is employed to monitor the crack surface opening distance. We demonstrate that with dynamic force balance achieved by pulse shaping, the peak of the far-field load synchronizes with the specimen fracture time. Furthermore, the evolution of dynamic stress intensity factor (SIF) obtained from the dynamic finite element analysis agrees with that from quasi-static analysis. These results prove that with dynamic force balance in SHPB, the inertial effect is minimized even for samples with complex geometries like notched SCB disc. The dynamic force balance thus enables the regression of dynamic fracture toughness using quasi-static analysis. This dynamic SCB method provides an easy and cost-effective way to measure dynamic fracture toughness of rocks and other brittle materials.     

Rate effects on toughness in elastic nonlinear viscous solids

A micromechanics-based constitutive relation for void growth in a nonlinear viscous solid is proposed to study rate effects on fracture toughness. This relation is incorporated into a microporous strip of cell elements embedded in a computational model for crack growth. The microporous strip is surrounded by an elastic nonlinear viscous solid referred to as the background material. Under steady-state crack growth, two dissipative processes contribute to the macroscopic fracture toughness—the work of separation in the strip of cell elements and energy dissipation by inelastic deformation in the background material. As the crack velocity increases, voids grow in the strain-rate strengthened microporous strip, thereby elevating the work of separation. In contrast, the energy dissipation in the background material decreases as the crack velocity increases. In the regime where the work of separation dominates energy dissipation, toughness increases with crack velocity. In the regime where energy dissipation is dominant, toughness decreases with crack velocity. Computational simulations show that the two regimes can exist in certain range of crack velocities for a given material. The existence of these regimes is greatly influenced by the rate dependence of the void growth mechanism (and the initial void size) as well as that of the bulk material. This competition between the two dissipative processes produces a U-shaped toughness-crack velocity curve. Our computational simulations predict trends that agree with fracture toughness vs. crack velocity data reported in several experimental studies for glassy polymers and rubber-modified epoxies.     

平面应变下紧凑拉伸试样的动态断裂韧性的实验研究

材料的动态断裂韧性是衡量材料在动载荷作用下抵杭裂纹扩展能力的重要指标,以往的材料动态断裂韧性测试多采用三点弯曲试样,而针对紧凑拉伸试样的动态断裂韧性研究很少.本文将紧凑拉伸试样(即CT试样)简化成等效弹簧质量模型,得到了CT试样动态应力强度因子的近似表达式.对Hopkinson压杆装置进行了改进,利用改进后的实验装置进...     

Effect of Notch-Tip Radius on Dynamic Brittle Fracture of Polycarbonate

Polycarbonate (PC), which is considered to be a ductile amorphous polymer, is prone to brittle fracture in the presence of sharp notches. In the present work, effect of notch-tip radius on brittle fracture of PC is studied under static and under dynamic loading (high loading rates) conditions. Towards this end, a hybrid experimental and numerical approach is adopted. Dynamic fracture experiments using Hopkinson bar setup are performed on single-edge notched specimen of PC having different notch-tip radii. Ultra-high speed imaging is used for real-time observation of the fracture process. Finite element simulations are simultaneously performed using a well calibrated elastic-viscoplastic constitutive model for polymers. In the presence of a notch, brittle fracture in PC starts with a defect nucleation ahead of it. For each notch-tip radii, we are experimentally able to capture the process of defect initiation and quantify the mean stress required, static as well as dynamic loading. We found that the mean stress required for defect nucleation increases with decreasing notch-tip radius due to increased triaxility at the notch-tip. Defect initiation stresses are also higher for dynamic conditions compared to static loading. Defect initiation toughness for dynamic loading is always higher than those for static loading, but reduction in defect initiation toughness with decreasing notch-tip is severe for dynamic loading.     

Meshless simulation of crack propagation in multiphase materials

The material body considered in this work consists of multiphases. Digital imaging data are taken as the input to specify the configuration and composition of the specimen. Meshless method is demonstrated as a superior numerical tool to analyze crack initiation and propagation in multiphase material. A fracture criterion, based on the ratio of the opening stress over the material toughness distributed in front of the crack tip, is proposed to determine the direction of crack propagation of mixed mode fracture problem in multiphase material. Numerical results are presented and discussed.     

Finite Fracture Mechanics model for mixed mode fracture in adhesive joints

Up to now the failure load assessment of bonded joints is still not fully understood. This work provides a new approach for assessing the crack initiation load of bonded joints. A failure model for single lap joints is proposed that is based on Finite Fracture Mechanics. Only two basic fracture parameters are required: the tensile strength and the fracture toughness of the adhesive. A coupled stress and energy criterion proposed in 2002 by Leguillon is used to model crack initiation in the adhesive layer. The theory of this criterion is outlined in detail, its relationship to other failure criteria is discussed and an overview of applications found in literature is given. An enhanced weak interface model that predicts a linear variation of the shear stresses in the adhesive layer is utilized to model the single lap joint. To compare joint designs and to reveal the limitations of the given approach a dimensionless brittleness number for mixed-mode loading is proposed. Along with a detailed discussion of the results for exemplary joint designs a comparison to experimental results from literature is performed. The two necessary fracture parameters are each taken from standard test results published in literature. A good agreement of the failure load predictions with the experimental results is observed. A remarkable outcome is that the presented failure model renders the adhesive thickness effect correctly. The paper concludes with a discussion of the limitations of the approach and the effect of material parameters.     

碳纤维复合材料冲击模型率相关修正方法与试验研究

目前先进航空发动机的风扇叶片均采用复合材料结构,为了研究其在工作过程中可能受到的冲击损伤,即碳纤维增强树脂基复合材料受到高速冲击后的损伤与破坏过程,对其准静态下的正交各向异性本构模型和失效准则进行修正,建立了应变率相关的三维动态本构及损伤模型．该模型考虑了材料模量、强度和断裂韧性与应变率的相关性,并采用基于断裂韧性的渐进损伤模式对刚度进行折减来控制破坏过程．开展了不同应变率下的动态试验,得到基体方向拉伸与剪切的动态响应数据,拟合得到相应的动态修正因子．将该模型结合修正因子植入数值软件进行仿真计算,分析结果表明,所建立的率相关本构及损伤模型能够更准确地模拟层合板受冲击过程的损伤和破坏,与试验吻合较好．