An Efficient Separation Method of Polysaccharides: Preparation of an Antitumor Polysaccharide APS-2 from Auricularia polytricha by Radial Flow Chromatography

Auricularia polytricha is an edible mushroom, quite popular in China. Modern pharmacology research indicate that A. polytricha polysaccharides possess antitumor and immunomodulatory activities. In this paper, an antitumor Auricularia polytricha polysaccharide (APS)-2 was purified by radial flow chromatography (RFC) in a column of 500 mL bed-volume (40 cm i.d × 15 cm) packed with DEAE52-cellulose anion ion-exchange resin. The optimal separation conditions were: sample flow-velocity 15–20 mL min^?1, sample volume 160–200 mL, and elution with distilled water and 0.2 M NaCl at a velocity of 35–45 mL min^?1. The yield and content of APS-2 obtained under these conditions were 182 mg g^?1 total polysaccharides and 98.35 %, respectively. The study provides guidelines for the separation and purification of polysaccharides using a radial flow chromatography column.     

Modeling of fixed-bed column studies for removal of cobalt ions from aqueous solution using <Emphasis Type="Italic">Chrysanthemum indicum</Emphasis>

The present study investigates the adsorption capability of raw and biochar forms of Chrysanthemum indicum flowers biomass to remove cobalt ions from aqueous solution in a fixed-bed column. Column adsorption experiments were conducted by varying the bed height (1.0, 2.0, 3.0 cm), flow rate (1.0, 2.5, 5.0 mL min^?1) and initial cobalt ion concentration (25, 50, 75 mg L^?1) to obtain the experimental breakthrough curves. The adsorption capacity of the raw and biochar forms of C. indicum flowers were found to be 14.84 and 28.34 mg g^?1, respectively, for an initial ion concentration of 50 mg L^?1 at 1.0 cm bed height and 1.0 mL min^?1 flow rate for Co (II) ion adsorption. Adam–Bohart, Thomas and Yoon–Nelson models were applied to the experimental column data to analyze the column performance. The Thomas model was found to best represent the column data with the predicted and experimental uptake capacity values correlating well and with higher R ² values for all the varying process parameters. Desorption studies revealed the suitability of the adsorbents for repeated use up to four adsorption–desorption cycles without significant loss in its efficiency. It can thus be inferred from the fixed-bed column studies that C. indicum flowers can suitably be used as an effective adsorbent for Co (II) ion removal from aqueous solution on a higher scale.     

An Efficient Separation Method of Polysaccharides: Preparation of an Antitumor Polysaccharide APS-2 from Auricularia polytricha by Radial Flow Chromatography

Auricularia polytricha is an edible mushroom, quite popular in China. Modern pharmacology research indicate that A. polytricha polysaccharides possess antitumor and immunomodulatory activities. In this paper, an antitumor Auricularia polytricha polysaccharide (APS)-2 was purified by radial flow chromatography (RFC) in a column of 500 mL bed-volume (40 cm i.d × 15 cm) packed with DEAE52-cellulose anion ion-exchange resin. The optimal separation conditions were: sample flow-velocity 15–20 mL min⁻¹, sample volume 160–200 mL, and elution with distilled water and 0.2 M NaCl at a velocity of 35–45 mL min⁻¹. The yield and content of APS-2 obtained under these conditions were 182 mg g⁻¹ total polysaccharides and 98.35 %, respectively. The study provides guidelines for the separation and purification of polysaccharides using a radial flow chromatography column.

     

Online thorium determination after preconcentration in a minicolumn having XAD-4 resin impregnated with N-benzoylphenylhydroxylamine by FI-spectrophotometry

A very sensitive and selective flow injection on-line determination method of thorium (IV) after preconcentration in a minicolumn having XAD-4 resin impregnated with N-benzoylphenylhydroxylamine is described. Thorium (IV) was selectively adsorbed from aqueous solution of pH 4.5 in a minicolumn at a flow rate of 13.6 mL min^?1, eluted with 3.6 mol dm^?3 HCl (5.6 mL min^?1), mixed with arsenazo-III (0.05% in 3.6 mol dm^?3 HCl stabilized with 1% Triton X-100, 5.6 mL min^?1) at confluence point and taken to the flow through cell of spectrophotometer where its absorbance was measured at 660 nm. Peak height was used for data analyses. The preconcentration factors obtained were 32 and 162, detection limits of 0.76 and 0.150 ??g L^?1, sample throughputs of 40 and 11 h^?1 for preconcentration times of 60 and 300 s, respectively. The tolerance levels for Zr(IV) and U(VI) metal ions is increased to 50-folds higher concentration to Th(IV). The proposed method was applied on different spiked tap water, sea water and biological sample and good recovery was obtained. The method was also applied on certified reference material IAEA-SL1 (Lake Sediment) for the determination of thorium and the results were in good agreement with the reported value.     

On-line spectrophotometric determination of scandium after preconcentration on XAD-4 resin impregnated with nalidixic acid

An on-line scandium preconcentration and determination method was developed with spectrophotometer associated with flow injection. Scandium from aqueous sample solution of pH 4.5 was selectively retained in the minicolumn containing XAD-4 resin impregnated with nalidixic acid at a flow rate of 11.8 mL min^?1 as scandium–nalidixic acid complex. The scandium complex was desorbed from the resin by 0.1 mol L^?1 HCl at a flow rate of 3.2 mL min^?1 and mixed with arsenazo-III solution (0.05 % solution in 0.1 mol L^?1 HCl, 3.2 mL min^?1) and taken to the flow through cell of spectrophotometer where its absorbance was measured at 640 nm. The preconcentration factors obtained were 35 and 155; detection limits of 1.4 and 0.32 μg L^?1 and sample throughputs of 40 and 11 were obtained for preconcentration time of 60 and 300 s, respectively. The tolerance limits of many interfering cations like Th(IV), U (VI), rare-earths and anions like tartrate, citrate, oxalate and fluoride were improved. The method was successfully applied to the determination of scandium from mock seawater samples and good recovery was obtained. The method was also validated on certified reference material IAEA-SL-1 (lake sediment) and the result was in good agreement with the reported value.     

Determination of Triazine Herbicides and Metabolites by Solid Phase Extraction with HPLC Analysis

An efficient solid phase extractive preconcentration/separation method was developed for the trace determination of herbicides in aqueous samples using Amberlite XAD-4 resin as the adsorbent. The retained herbicides were eluted with methanol at a flow rate of 1.0 mL min^?1 and determined by HPLC-DAD (wavelength of 220 nm) using water (pH:4.7, phosphoric acid) and methanol (ratio 35:65) as the mobile phase with a flow rate of 1.0 mL min^?1. Quantitative recoveries of simazine, atrazine and its metabolities were achieved at optimized analysis conditions that included 0.75 g of resin; a pH of 3.0; an eluent volume of 3.0 mL; an eluent flow rate of 1.0 mL min^?1; and a sample flow rate of 4.0 mL min^?1. The limits of detection, preconcentration factor, and linear ranges for the herbicides were 0.084–0.121 µgL^?1, 1000, and 0.5–20 mg L^?1, respectively. The performance of the method was evaluated by analysis of spiked water samples. The recoveries of simazine, atrazine and their metabolities were found to be quantitative (99.6–104.8%) with RSDs of 2.2–4.8% and 2.8–4.7% for intra-day and inter-day precision, respectively. The proposed method was successfully applied for trace determination of studied analytes in waste water, apple juice, and red wine samples.     

Determination of Ferulic Acid in Rat Plasma by Liquid Chromatography–Tandem Mass Spectrometry Method: Application to a Pharmacokinetic Study

Abstract

A rapid, sensitive, and specific liquid chromatography–tandem mass spectrometric (HPLC-MS/MS) method has been developed for quantification of ferulic acid in rat plasma. The analyte and docetaxel (internal standard) were extracted from plasma samples with diethyl ether and analyzed on a C₁₈ column. The chromatographic separation was achieved within 3.5 min by using acetonitrile-water as the mobile phase and the flow rate was 0.2 mL · min^?1. The method was linear within the range of 0.5 ? 800 ng · mL^?1. The lower limit of quantification (LLOQ) was 0.5 ng · mL^?1. Finally, the method is successfully applied for the pharmacokinetic study of ferulic acid in rats following intravenous administration.     

Removal of uranium(VI) from aqueous solutions using nanoporous ZnO prepared with microwave-assisted combustion synthesis

The adsorption of the uranyl ions from aqueous solutions on the nanoporous ZnO powders has been investigated under different experimental conditions. The adsorption of uranyl on nanoporous ZnO powders were examined as a function of the contact times, pH of the solution, concentration of uranium(VI) and temperature. The ability of this material to remove U(VI) from aqueous solution was followed by a series of Langmuir and Freunlinch adsorption isotherms. The adsorption percent and distribution coefficient for nanoporous ZnO powders were 98.65 % ± 1.05 and 7,304 mL g^?1, respectively. The optimum conditions were found as at pH 5.0, contact time 1 h, at 1/5 Zn²⁺/urea ratio, 50 ppm U(VI) concentration and 303 K. The monomolecular adsorption capacity of nanoporous ZnO powders for U(VI) was found to be 1,111 mg g^?1 at 303 K. Using the thermodynamic equilibrium constants obtained at different temperatures, various thermodynamic parameters, such as ΔG°, ΔH° and ΔS°, have been calculated. Thermodynamic parameters (ΔH° = 28.1 kJ mol ^?1, ΔS° = 160.30 J mol^?1 K^?1, ΔG° = ?48.54 kJ mol^?1) showed the endothermic and spontaneous of the process. The results suggested that nanoporous ZnO powders was suitable as sorbent material for recovery and adsorption of U(VI) ions from aqueous solutions.     

SPE and LC–ESI–MS for Quantitative Analysis of Mitiglinide in Human Plasma in a Bioequivalence Study

Liquid chromatography–electrospray ionization mass spectrometry has been used for rapid, selective, and sensitive quantitative analysis of mitiglinide in human plasma. Sample pretreatment involved solid-phase extraction from plasma with gliclazide as internal standard. Separation was performed on a C₁₈ column (150 × 2.0 mm) with 71:29 (v/v) acetonitrile–water (containing 0.1% formic acid and 0.2 mmol L^?1 ammonium acetate) as mobile phase at a flow rate of 0.2 mL min^?1. The method was validated then successfully applied to a clinical bioequivalence study of mitiglinide in 20 healthy volunteers after oral administration.     

FI-spectrophotometric determination of uranium after preconcentration on an anion exchange resin

An economical, fast, sensitive and selective method for the determination of uranium (VI) from sulfate media based on the flow injection on-line preconcentration in a minicolumn having amberlite IRA-402 (strong anion exchange) resin is described. Uranium (VI) was selectively adsorbed on the resin as uranyl trisulfate complex from aqueous solution of pH 2 in the minicolumn (2.56 mm i.d. and 7.5 cm in length) at a flow rate of 10 ml min^?1. The adsorbed uranyl trisulfate complex was eluted by HClO₄ (0.1 mol l^?1, 6.5 ml min^?1) and mixed with arsenazo-III (0.05 %, 6.5 ml min^?1), and passed through the flow through cell of spectrophotometer where its absorbance was measured at 653 nm. Various parameters affecting adsorption and elution of the uranium complex were optimized. For data analyses peak absorbance was used. For 60 and 180 s preconcentration time, enrichment factors (EF) 20 and 40, sampling frequency (SF) 45 and 18 h^?1; and detection limits (DL) (3σ) 14.2 and 8.6 μg l^?1 were obtained, respectively. To enhance the sensitivity of the system, two minicolumns (described above) were used for simultaneous preconcentration and elution purpose. For 60 and 180 s preconcentration time, EF 30 and 50, SF 42 and 17 h^?1 and DL (3σ) 4.4 and 3.44 μg l^?1 were obtained, respectively. The effect of various anions and cations was studied for single column manifold. High selectivity of this method was observed. All the anions and cations studied did not interfere up to 330 times higher mass ratio to 300 μg l^?1 U (VI) except Th(IV) which was tolerated up to 133 times by the addition of washing step in the manifold. The method based on single column manifold was applied on the spiked tap water, biological sample CRM (IAEA-V4) and synthetic leach liquor solution and good recovery was obtained. The method based on dual column manifold was validated on lake sediment SL-1 (CRM) and the results obtained were in good agreement at 95 % confidence level with the given value.     

A Validated LC Method for the Quantitation of Cefotaxime in pH-Sensitive Nanoparticles

A sensitive and rapid routine LC method was validated for measuring cefotaxime incorporated in three different pH-sensitive nanoparticles. The drug was chromatographed on a C18 reversed-phase column; the mobile phase used was 0.05 M aqueous ammonium acetate, acetonitrile and tetrahydrofuran (87:11:2, v/v) adjusted to pH 5.5 with acetic acid. The flow rate was 1 mL min^?1 and cefotaxime was quantified at 254 nm, with a sensitivity range of 0.005 AUFS. The validated method was specific, linear (R ² ≥ 0.999), precise and accurate in a concentration range of 0.2–50.0 μg mL^?1. The method was rapid, selective and suitable for evaluation of cefotaxime in pH-sensitive Eudragit nanoparticles.     

Effect of the catalyst MCM-41 on the kinetic of the thermal decomposition of poly(ethylene terephthalate)

The aim of this work is to determine the activation energy for the thermal decomposition of poly(ethylene terephthalate)—PET, in the presence of a MCM-41 mesoporous catalyst. This material was synthesized by the hydrothermal method, using cetyltrimethylammonium as template. The PET sample has been submitted to thermal degradation alone and in presence of MCM-41 catalyst at a concentration of 25% in mass (MCM-41/PET). The degradation process was evaluated by thermogravimetry, at temperature range from 350 to 500 °C, under nitrogen atmosphere, with heating rates of 5, 10 and 25 °C min^?1. From TG, the activation energy, determined using the Flynn–Wall kinetic method, decreased from 231 kJ mol^?1, for the pure polymer (PET), to 195 kJ mol^?1, in the presence of the material (MCM-41/PET), showing the catalyst efficiency for the polymer decomposition process.     

Development and Validation of a Reversed-Phase HPLC Method for the Determination of Deflazacort in Pharmaceutical Dosage Forms

A reversed-phase high-performance liquid chromatographic method has been developed and validated for quantitative determination of deflazacort in tablets and in compounded capsules. Isocratic chromatography was performed on a C₁₈ column with acetonitrile–water 80:20 (v/v) as mobile phase at a flow rate of 1.0 mL min^?1. UV detection was at 240 nm. The linearity of the method was good (r > 0.999), as also were intra-day and inter-day precision (RSD <2%) and accuracy (recovery >98%). The method was also validated for specificity and robustness. The results showed the proposed method is suitable for its intended use.     

Determination of Vecuronium Bromide in Pharmaceuticals: Development, Validation and Comparative Study of HPLC and CZE Analytical Methods

Vecuronium bromide is a neuromuscular blocking agent used for anesthesia to induce skeletal muscle relaxation. HPLC and CZE analytical methods were developed and validated for the quantitative determination of vecuronium bromide. The HPLC method was achieved on an amino column (Luna 150 × 4.6 mm, 5 μm) using UV detection at 205 nm. The mobile phase was composed of acetonitrile:water containing 25.0 mmol L^?1 of sodium phosphate monobasic (50:50 v/v), pH 4.6 and flow rate of 1.0 mL min^?1. The CZE method was achieved on an uncoated fused-silica capillary (40.0 cm total length, 31.5 cm effective length and 50 μm i.d.) using indirect UV detection at 230 nm. The electrolyte comprised 1.0 mmol L^?1 of quinine sulfate dihydrate at pH 3.3 and 8.0% of acetonitrile. The results were used to compare both techniques. No significant differences were observed (p > 0.05).     

Estimation of Perospirone in Human Plasma by LC–MS–MS and Its Application to Pharmacokinetics Study

A sensitive liquid chromatography-tandem-mass spectrometry method was developed and validated for the determination of perospirone in human plasma, using quetiapine as internal standard. Plasma samples were extracted from 1 mL of plasma using n-hexane. Chromatographic separation was performed on an Agilent Zorbax SB C₁₈ column with a mobile phase of 5 mM ammonium acetate solution-methanol (12:88, v/v, adjusted to pH 3.8 with glacial acetic acid) at a flow rate of 0.2 mL min^?1. The chromatographic separation was achieved in less than 4.6 min. The linearity was established over the concentration range of 0.05–20 ng mL^?1. Both of the intra- and inter-batch standard deviation was less than 9.8%. The method was successfully applied to study the pharmacokinetic parameters of perospirone hydrochloride tablets in healthy Chinese volunteers.     

LC Method with Precolumn Derivatization for Analysis of Mexiletine in Pharmaceutical Preparations

A isocratic, selective and accurate LC method of analysis of mexiletine in pharmaceutical preparations has been developed and validated. The method is based on derivatization of mexiletine with 4-chloro-7-nitrobenzofurazan in pH 9.0 borate buffer to yield a yellow product. Chromatography was performed on a C₁₈ column (150 × 4.6 mm i.d.) with acetonitrile–water 80:20 (v/v) as mobile phase at a flow rate of 1.0 mL min^?1. UV–visible absorbance detection was performed at 458 nm. The retention time of the mexiletine derivative was 4.10 min, and response was a linear function of concentration in the range 0.5–4.0 μg mL^?1 (r = 0.9998). The limits of detection and quantification were 0.05 and 0.15 μg mL^?1, respectively. Method validation revealed precision, sensitivity, and robustness were acceptable. Low RSD values are indicative of high precision, and high recovery values are indicative of the accuracy of the method. Results obtained by use of the proposed method for analysis of the mexiletine content of pharmaceutical a preparation were compared with those obtained by use of the official method. The method has been used for analysis of pharmaceutical preparations.     

Simultaneous Determination of Ibuprofen and Diphenhydramine Citrate in Tablets by Validated LC

A stability-indicating LC method was developed for the simultaneous determination of ibuprofen and diphenhydramine citrate in pharmaceutical dosage forms. The chromatographic separation was achieved on an Inertsil ODS 3V, 150 × 4.6 mm, 5 μm, column. The mobile phase contained a mixture of 50 mM potassium dihydrogen phosphate buffer:acetonitrile:triethylamine:glacial acetic acid (55:45:0.2:0.2, v/v/v/v). This method allowed the determination of 2.85–9.14 mg mL^?1 of ibuprofen and 0.54–1.73 mg mL^?1 of diphenhydramine citrate, in a diluent consisting of pH 7.2, 50 mM potassium dihydrogen phosphate buffer:acetonitrile (40:60, v/v). The flow rate was 1.2 mL min^?1 and the detection wavelength was 260 nm. The limit of detection for ibuprofen and diphenhydramine citrate was 1.72 and 0.54 μg mL^?1 and the limit of quantification was 5.73 and 1.64 μg mL^?1, respectively. This method was validated for accuracy, precision and linearity. The method was also found to be stability indicating.     

Comparative solid phase extraction study on the U(VI) preconcentration by using immobilized thermotolerant <Emphasis Type="Italic">Bacillus vallismortis</Emphasis> and <Emphasis Type="Italic">Bacillus mojavensis</Emphasis>

Bacillus vallismortis and Bacillus mojavensis were loaded onto Amberlite XAD-4 resin and used for solid phase extraction (SPE) of uranium(VI). A quick and simple UV–Vis spectrophotometric method was used to determine U(VI) ion. The best experimental conditions were determined as being a pH of 5.0; a sample flow rate of 2.0 mL min^?1; 200.0 mg of biosorbent; 800 mg of Amberlite XAD-4, and 5.0 mL of 1 mol L^?1 HCl as desorption solution for both immobilized bacteria. The preconcentration factors were achieved as 80 for both solid phase extractor. The developed methods were validated by applying to reference water and tea samples.     

A Simple and Sensitive LC Method for Quantification of Cefteram in Human Plasma

A simple and sensitive liquid chromatographic method was developed for quantification of cefteram in human plasma. Amoxicillin was used as an internal standard. The present method used protein precipitation for extraction of cefteram from human plasma. Separation was carried out on a reversed-phase C₁₈ column. The column effluent was monitored by UV detection at 262 nm. The mobile phase was a mixture of methanol and water containing 0.3% v/v triethylamine and 0.6% v/v glacial acetic acid (35:65:0.3:0.6 v/v) at a flow rate of 0.30 mL min^?1. The column temperature was 20 °C. This method was linear over the range of 47.5–4,750.0 ng mL^?1 with determination coefficient greater than 0.99. The mean extraction recovery of cefteram and IS was ≥76.82 and ≥76.49%, respectively, and the method was found to be precise, accurate, and specific during the study. The method was successfully applied for a pharmacokinetic study of cefteram in human.