Synthesis of Fe3O4 nanoparticles without inert gas protection used as precursors of magnetic fluids

Fe₃O₄ nanoparticles were hydrothermally synthesized under continuous microwave irradiation from FeCl₃·6H₂O and FeSO₄·7H₂O aqueous solutions, using NH₄OH as precipitating reagent and N₂H₄·H₂O as oxidation-resistant reagent. The results of X-ray powder diffraction (XRD), FT–IR spectroscopy and scanning electron microscopy (SEM) measurements showed that the synthesized magnetite (Fe₃O₄) nanoparticles had an average diameter of 10 nm. The magnetic properties of the Fe₃O₄ nanoparticles were measured using a vibrating sample magnetometer (VSM), indicating that the nanoparticles possessed high saturation magnetization at room temperature. The Fe₃O₄ nanoparticles were used to prepare magnetic fluids (MFs) based on water, and the properties of the MFs were characterized by a Gouy magnetic balance, a capillary rheometer and a rotating rheometer, respectively.     

Microwave synthesis of magnetic Fe3O4 nanoparticles used as a precursor of nanocomposites and ferrofluids

Methods to synthesize magnetic Fe₃O₄ nanoparticles and to modify the surface of particles are presented in the present investigation. Fe₃O₄ magnetic nanoparticles were prepared by the co-precipitation of Fe³⁺ and Fe²⁺, NH₃·H₂O was used as the precipitating agent to adjust the pH value, and the aging of Fe₃O₄ magnetic nanoparticles was accelerated by microwave (MW) irradiation. The obtained Fe₃O₄ magnetic nanoparticles were characterized by Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM), X-ray powder diffraction (XRD) and vibrating sample magnetometer (VSM). The average size of Fe₃O₄ crystallites was found to be around 8–9 nm. Thereafter, the surface of Fe₃O₄ magnetic nanoparticles was modified by stearic acid. The resultant sample was characterized by FT-IR, scanning electron microscopy (SEM), XRD, lipophilic degree (LD) and sedimentation test. The FT-IR results indicated that a covalent bond was formed by chemical reaction between the hydroxyl groups on the surface of Fe₃O₄ nanoparticles and carboxyl groups of stearic acid, which changed the polarity of Fe₃O₄ nanoparticles. The dispersion of Fe₃O₄ in organic solvent was greatly improved. Effects of reaction time, reaction temperature and concentration of stearic acid on particle surface modification were investigated. In addition, Fe₃O₄/polystyrene (PS) nanocomposite was synthesized by adding surface modified Fe₃O₄ magnetic nanoparticles into styrene monomer, followed by the radical polymerization. The obtained nanocomposite was tested by thermogravimetry (TG), differential scanning calorimetry (DSC) and XRD. Results revealed that the thermal stability of PS was not significantly changed after adding Fe₃O₄ nanoparticles. The Fe₃O₄ magnetic fluid was characterized using UV–vis spectrophotometer, Gouy magnetic balance and laser particle-size analyzer. The testing results showed that the magnetic fluid had excellent stability, and had susceptibility of 4.46×10⁻⁸ and saturated magnetization of 6.56 emu/g. In addition, the mean size d (0.99) of magnetic Fe₃O₄ nanoparticles in the fluid was 36.19 nm.     

A study of modified Fe3O4 nanoparticles for the synthesis of ionic ferrofluids

XRD and XPS analyses revealed that a Fe(NO₃)₃·9H₂O layer formed outside γ-Fe₂O₃ particles when Fe₃O₄ nanoparticles were treated with ferric nitrate. The particle density differed for untreated and treated particles and was not uniform for the latter. The specific saturation magnetization of both treated and untreated particles was used to estimate the thickness of the Fe(NO₃)₃·9H₂O layer and the average density of the treated particles. The density of the treated particles was used to calculate the density of ferrofluids of different particle volume fractions. These values are in agreement with measured results. Therefore, the particle volume fraction can be designed to synthesize acid ionic ferrofluids based on Fe₃O₄ nanoparticles using Massart's method.     

Synthesis of Co-Cu-Zn doped Fe3O4 nanoparticles with tunable morphology and magnetic properties

Co-Cu-Zn doped Fe₃O₄ nanoparticles can be successfully synthesized using a simple method. The particles in the size range 20−400 nm with different regular shapes i.e. sphere-like, regular hexane and tetrahedron are controllably achieved by changing the metal ion concentration. Compared to pure Fe₃O₄ without dopants, Co-Cu-Zn doped Fe₃O₄ nanoparticles exhibit better microwave absorbing properties at 2−18 GHz. Among three Co-Cu-Zn doped Fe₃O₄ nanoparticles with different morphologies, tetrahedral Co-Cu-Zn doped Fe₃O₄ nanoparticles represent a better dielectric loss in high frequency range. This work is believed the first known report of Co-Cu-Zn doped Fe₃O₄ nanoparticles with tunable morphology and magnetic properties through the hydrothermal process without using any organic solvents, organic metal salts or surfactants.     

Magnetic and rheological properties of monodisperse Fe3O4 nanoparticle/organic hybrid

Fe₃O₄ nanoparticle/organic hybrids were synthesized via hydrolysis using iron (III) acetylacetonate at ∼80 °C. The synthesis of Fe₃O₄ was confirmed by X-ray diffraction, selected-area diffraction, and X-ray photoelectron spectroscopy. Fe₃O₄ nanoparticles in the organic matrix had diameters ranging from 7 to 13 nm depending on the conditions of hydrolysis. The saturation magnetization of the hybrid increased with an increase in the particle size. When the hybrid contained Fe₃O₄ particles with a size of less than 10 nm, it exhibited superparamagnetic behavior. The blocking temperature of the hybrid containing Fe₃O₄ particles with a size of 7.3 nm was 200 K, and it increased to 310 K as the particle size increased to 9.1 nm. A hybrid containing Fe₃O₄ particles of size greater than 10 nm was ferrimagnetic, and underwent Verwey transition at 130 K. Under a magnetic field, a suspension of the hybrid in silicone oil revealed the magnetorheological effect. The yield stress of the fluid was dependent on the saturation magnetization of Fe₃O₄ nanoparticles in the hybrid, the strength of the magnetic field, and the amount of the hybrid.     

Synthesis and characterization of Fe3O4@C@Ag nanocomposites and their antibacterial performance

We synthesized Fe₃O₄@C@Ag nanocomposites through a combination of solvothermal, hydrothermal, and chemical redox reactions. Characterization of the resulting samples by X-ray diffraction, Fourier-transform infrared spectroscopy, field-emission scanning and transmission electron microscopy, and magnetic measurement is reported. Compared to Fe₃O₄@Ag nanocomposites, the Fe₃O₄@C@Ag nanocomposites showed enhanced antibacterial activity. The Fe₃O₄@C@Ag nanocomposites were able to almost entirely prevent growth of Escherichia coli when the concentration of Ag nanoparticles was 10 μg/mL. Antibacterial activity of the Fe₃O₄@C@Ag nanocomposites was maintained for more than 40 h at 37 °C. The intermediate carbon layer not only protects magnetic core, but also improves the dispersion and antibacterial activity of the silver nanoparticles. The magnetic core can be used to control the specific location of the antibacterial agent (via external magnetic field) and to recycle the residual silver nanoparticles. The Fe₃O₄@C@Ag nanocomposites will have potential uses in many fields as catalysts, absorbents, and bifunctional magnetic-optical materials.     

Magnetic field synthesis of Fe3O4 nanoparticles used as a precursor of ferrofluids

Methods to synthesize magnetic Fe₃O₄ nanoparticles and to modify the nanoparticle surface are presented in this paper. In these methods, Fe₃O₄ nanoparticles were prepared by co-precipitation, and the aging of nanoparticles was improved by applied magnetic field. The obtained nanoparticles were characterized by Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), X-ray powder diffraction (XRD), and vibrating sample magnetometer (VSM). Thereafter, to enhance the compatibility between nanoparticles and water, an effective surface modification method was developed by grafting acrylic acid onto the nanoparticle surface. FT-IR, XRD, transmission electron microscopy (TEM), and thermogravimetry (TG) were used to characterize the resultant sample. The testing results indicated that the polyacrylic acid chains have been covalently bonded to the surface of magnetic Fe₃O₄ nanoparticles. The effects of initiator dosage, monomer concentration, and reaction temperature on the characteristics of surface-modified Fe₃O₄ nanoparticles were investigated. Moreover, the Fe₃O₄-g-PAA hybrid nanoparticles were dispersed in water to form ferrofluids (FFs). The obtained FFs were characterized by UV–vis spectrophotometer, Gouy magnetic balance and laser particle-size analyzer. The testing results showed that the high-concentration FF had excellent stability, with high susceptibility and high saturation magnetization. The rheological properties of the FFs were also investigated using a rotating rheometer.     

Heat dissipation and magnetic properties of surface-coated Fe3O4 nanoparticles for biomedical applications

In this study, the influence of surface coating on the magnetic and heat dissipation properties of Fe₃O₄ nanoparticles was investigated. Fe₃O₄ nanoparticles that ranged in size between (particle sizes of 20 and 30 nm) were coated with polyethylenimine (PEI), oleic acid, and Pluronic F-127. Surface coatings that were composed of thick layers of oleic acid and Pluronic F-127 reduced dipole interactions between the particles, and resulted in reduced coercivity and decreased Néel relaxation times. The ac magnetization measurements revealed that the heat dissipation of the PEI-coated Fe₃O₄ nanoparticles was induced by hysteresis loss and Brownian relaxation loss and that of the oleic-acid-coated Fe₃O₄ nanoparticles was mainly induced by hysteresis loss and Néel relaxation loss.     

Surface functionalization of chitosan-coated magnetic nanoparticles for covalent immobilization of yeast alcohol dehydrogenase from Saccharomyces cerevisiae

A novel and efficient immobilization of yeast alcohol dehydrogenase (YADH, EC1.1.1.1) from Saccharomyces cerevisiae has been developed by using the surface functionalization of chitosan-coated magnetic nanoparticles (Fe₃O₄/KCTS) as support. The magnetic Fe₃O₄/KCTS nanoparticles were prepared by binding chitosan alpha-ketoglutaric acid (KCTS) onto the surface of magnetic Fe₃O₄ nanoparticles. Later, covalent immobilization of YADH was attempted onto the Fe₃O₄/KCTS nanoparticles. The effect of various preparation conditions on the immobilized YADH process such as immobilization time, enzyme concentration and pH was investigated. The influence of pH and temperature on the activity of the free and immobilized YADH using phenylglyoxylic acid as substrate has also been studied. The optimum reaction temperature and pH value for the enzymatic conversion catalyzed by the immobilized YADH were 30 °C and 7.4, respectively. Compared to the free enzyme, the immobilized YADH retained 65% of its original activity and exhibited significant thermal stability and good durability.     

Magnetic properties of prussian blue modified Fe3O4 nanocubes

Size controlled cubic Fe₃O₄ nanoparticles in the size range 90–10 nm were synthesized by varying the ferric ion concentration using the oxidation method. A bimodal size distribution was found without ferric ion concentration and the monodispersity increased with higher concentration. The saturation magnetization decreased from 90 to 62 emu/g when the particle size is reduced to 10 nm. The Fe₃O₄ nanoparticles with average particle sizes 10 and 90 nm were surface modified with prussian blue. The attachment of prussian blue with Fe₃O₄ was found to depend on the concentration of HCl and the particle size. The saturation magnetization of prussian blue modified Fe₃O₄ varied from 10 to 80 emu/g depending on the particle size. The increased tendency for the attachment of prussian blue with smaller particle size was explained based on the surface charge. The prussian blue modified magnetite nanoparticles could be used as a radiotoxin remover in detoxification applications.     

Sono-enhanced degradation of dye pollutants with the use of H2O2 activated by Fe3O4 magnetic nanoparticles as peroxidase mimetic

Sono-enhanced degradation of a dye pollutant Rhodamine B (RhB) was investigated by using H₂O₂ as a green oxidant and Fe₃O₄ magnetic nanoparticles (MNPs) as a peroxidase mimetic. It was found that Fe₃O₄ MNPs could catalyze the break of H₂O₂ to remove RhB in a wide pH range from 3.0 to 9.0 and its peroxidase-like activity was significantly enhanced by the ultrasound irradiation. At pH 5.0 and temperature 55 °C, the ultrasound-assisted H₂O₂–Fe₃O₄ catalysis removed about 95% of RhB (0.02 mmol L⁻¹) in 15 min with a apparent rate constant of 0.15 min⁻¹ for the degradation of RhB, being 6.5 and 37.6 folds of that in the simple catalytic H₂O₂–Fe₃O₄ system, and the simple ultrasonic US-H₂O₂ systems, respectively. The beneficial synergistic behavior between Fe₃O₄ catalysis and ultrasonic was demonstrated to be dependent on Fe₃O₄ dosage, H₂O₂ concentration, pH value and temperature. As a tentative explanation, the observed significant synergistic effects was attributed to the positive interaction between cavitation effect accelerating the catalytic breakdown of H₂O₂ over Fe₃O₄ nanoparticles, and the function of Fe₃O₄ MNPs providing more nucleation sites for the cavitation inception.     

Static susceptibility and heat capacity studies on V3O7·H2O7 nanobelts

V₃O₇·H₂O nanobelts were prepared by a hydrothermal method at 190 °C using V₂O₅·nH₂O gel and H₂C₂O₄·2H₂O as starting agents. The obtained nanobelts have diameters ranging from 40 to 70 nm with lengths up to several micrometers. Measurements of the static magnetic susceptibility and the specific heat show a discontinuous phase transition at around T=145 K, which separates two regions of paramagnetic behavior.     

α-Fe2O3-In2O3 mixed oxide nanoparticles synthesized under hydrothermal supercritical conditions

α-Fe₂O₃-In₂O₃ mixed oxide nanoparticles system has been synthesized by hydrothermal supercritical and postannealing route, starting with (1−x)Fe(NO₃)₃·9H₂O·xIn(NO₃)₃·5H₂O aqueous solution (x=0-1). X-ray diffraction and Mössbauer spectroscopy have been used to study the phase structure and substitutions in the nanosized samples. The concentration regions for the existence of the solid solutions in the α-Fe₂O₃-In₂O₃ nanoparticle system together with the solubility limits of In³⁺ ions in the hematite lattice and of Fe³⁺ ions in the cubic In₂O₃ structure have been evidenced. In general, the substitution level is considerably lower than the nominal concentration x. A justification of the processes leading to the formation of iron and indium phases in the investigated supercritical hydrothermal system has been given.     

Fabrication and characterization of magnetic Fe3O4-CNT composites

Carbon nanotubes (CNTs) decorated with magnetite nanoparticles on their external surface have been fabricated by in situ solvothermal method, which was conducted in benzene at 500 °C with ferrocene and CNTs as starting reagents. The as-prepared composites were characterized using XRD, FTIR, SEM and TEM. It has been found that the amount of magnetite nanoparticles deposited on the CNTs can be controlled by adjusting the initial mass ratio of ferrocene to CNTs. The Fe₃O₄-CNT composites display good ferromagnetic property at room temperature, with a saturation magnetization value (M_s) of 32.5 emu g⁻¹ and a coercivity (H_c) of 110 Oe.     

Synthesis and magnetic characterization of Zn0.6Ni0.4Fe2O4 nanoparticles via a polyethylene glycol-assisted hydrothermal route

Zn-doped nickel ferrite nanoparticles (Zn_0.6Ni_0.4Fe₂O₄) have been prepared via a surfactant, polyethylene glycol assisted hydrothermal route. X-ray powder diffractometry (XRD), Fourier transform infrared spectroscopy, transmission electron microscopy (TEM), and vibrating scanning magnetometry (VSM) were used for the structural, morphological, and magnetic characterizations of the product, respectively. TEM analysis revealed that the nanoparticles have a narrow size distribution, with average particle size of 15±1 nm, which agrees well with the XRD based estimate of 14±2 nm. The absence of saturation and remanent magnetization, and coercivity in the high temperature region of the M-H curve and non-zero magnetic moments indicate superparamagnetism of the nanoparticles with a canted spin structure. The appearance of a peak on the temperature-dependent zero-field cooling magnetization curve at ∼190 K indicates the blocking temperature of the sample.     

Magnetic characterization of surface-coated magnetic nanoparticles for biomedical application

The influence of the oleic acid surface coating on Fe₃O₄ and NiFe₂O₄ nanoparticles on their magnetic and calorimetric characterization was investigated. Fe₃O₄ nanoparticles (particle sizes of 15-20 and 20-30 nm) and NiFe₂O₄ nanoparticles (particle sizes of 20-30 nm) were dispersed in oleic acid. The surface coating resulted in a decrease in the dipole-dipole interaction between the particles, which in turn affected the coercivity and heat dissipation of the nanoparticles. The coercivity of the oleic-acid-coated nanoparticles was found to be lower than that of the uncoated nanoparticles. The temperature rise in the oleic-acid-coated nanoparticles was greater than that of the uncoated nanoparticles; this temperature rise was associated with the relaxation losses. The viscosity dependence on the self-heating temperature of Fe₃O₄ nanoparticles (15-20 and 20-30 nm) under an ac magnetic field was measured. The temperature rise for both the Fe₃O₄ nanoparticles (15-20 and 20-30 nm) exhibited a strong dependence on viscosity at each magnetic field frequency, and the contribution of Brownian relaxation loss to the temperature rise was revealed. Moreover, an in vitro cytotoxicity test of Fe₃O₄ and NiFe₂O₄ was performed using human cervical carcinoma cells (HeLa), and the cytotoxicity of NiFe₂O₄ nanoparticles was compared to that of Fe₃O₄ nanoparticles.     

Synthesis and investigation of magnetic properties of substituted ferrite nanoparticles of spinel system Mn1−xZnx[Fe2−yLy]O4

Superparamagnetic nanoparticles of the spinel ferrite four-element system Mn_1−xZn_x[Fe_2−yL_y]O₄ (where L:Gd³⁺, La³⁺, Ce³⁺, Eu³⁺, Dy³⁺, Er³⁺,Yb³⁺) were synthesized by the co-precipitation method. The magnetic moments of the 10 nm diameter nanoparticles were comparable to the ones of Fe₃O₄ nanoparticles. A comparatively low T_C (∼52–72 °C) was observed for some of the compositions. The heating mechanism of the superparamagnetic particles in the AC magnetic field at radiofrequency range is discussed and especially the absence of the hysteresis loop in the M–H curve at room temperature. One possible explanation—spontaneous particle agglomeration—was experimentally verified.     

Carbon nanotubes/magnetite hybrids prepared by a facile synthesis process and their magnetic properties

In this paper, a facile synthesis process is proposed to prepare multiwalled carbon nanotubes/magnetite (MWCNTs/Fe₃O₄) hybrids. The process involves two steps: (1) water-soluble CNTs are synthesized by one-pot modification using potassium persulfate (KPS) as oxidant. (2) Fe₃O₄ is assembled along the treated CNTs by employing a facile hydrothermal process with the presence of hydrazine hydrate as the mineralizer. The treated CNTs can be easily dispersed in aqueous solvent. Moreover, X-ray photoelectron spectroscopy (XPS) analysis reveals that several functional groups such as potassium carboxylate (-COOK), carbonyl (-CO) and hydroxyl (-C-OH) groups are formed on the nanotube surfaces. The MWCNTs/Fe₃O₄ hybrids are characterized with respect to crystal structure, morphology, element composition and magnetic property by X-ray diffraction (XRD), transmission electron microscopy (TEM), XPS and superconducting quantum interference device (SQUID) magnetometer. XRD and TEM results show that the Fe₃O₄ nanoparticles with diameter in the range of 20-60 nm were firmly assembled on the nanotube surface. The magnetic property investigation indicated that the CNTs/Fe₃O₄ hybrids exhibit a ferromagnetic behavior and possess a saturation magnetization of 32.2 emu/g. Further investigation indicates that the size of assembled Fe₃O₄ nanoparticles can be turned by varying experiment factors. Moreover, a probable growth mechanism for the preparation of CNTs/Fe₃O₄ hybrids was discussed.     

Iron phthalocyanine oligomer/Fe3O4 hybrid microspheres and their microwave absorption property

The novel nano-scale iron phthalocyanine oligomer/Fe₃O₄ (FePc/Fe₃O₄) hybrid microspheres were synthesized from iron phthalocyanine oligomer and FeCl₃·6H₂O via a solvent-thermal crystallization route. The morphology and structure of the hybrid microspheres were characterized by Fourier transform infrared spectrophotometer, X-ray diffraction, scanning electron microscopy and transmission electron microscopy. These results showed that the hybrids were monodisperse microspheres and the morphology can be adjusted by controlling pre-polymerization time. The saturation magnetization increased with increase in the pre-polymerization time, while the coercivities decreased. The FePc/Fe₃O₄ hybrid microspheres exhibited novel microwave electromagnetic properties: the dielectric loss was enhanced when the pre-polymerization time increased and a new microwave loss peak appeared at high frequency. The microwave absorbing properties enhanced with increase in the pre-polymerization time and a maximum reflection loss of −29.7 dB was obtained at 11.7 GHz with 6 h of pre-polymerization time when the matching thickness was 3.0 mm. The novel hybrid materials are believed to have potential applications as microwave absorbing materials.     

Synthesis protocol influence on aqueous magnetic fluid properties

Magnetic colloids containing superparamagnetic Fe₃O₄ nanoparticles have been prepared by co-precipitation method. Three samples of citric acid coated magnetic colloids containing magnetic nanoparticles (ultra-fine particles of Fe₃O₄) have been obtained following three different preparation protocols. Physical tests have been performed on these samples of the magnetic colloids prepared by us (consisting mainly of Fe₃O₄ ultra-fine particles stabilized with citric acid (C₆H₈O₇) and immersed in water), in order to reveal their microstructural and rheological features. Transmission electron microscopy (TEM) and magnetic measurements were the investigation methods used for the assessing of the magnetic nanoparticles size. The dimensional distribution of the ferrophase physical diameter was comparatively presented using the box-plot statistical method. Infrared absorption spectra have been recorded aiming to get some information on the magnetic fluid composition.