Study of magnetic phases in mechanically alloyed Fe50Zn50 powder

The mechanosynthesis of Fe₅₀Zn₅₀ alloy resulted in the formation of the bcc Fe(Zn) solid solution after 20 h of milling. Structural transformations induced by mechanical alloying and heating, and magnetic properties of the powders were studied by Mössbauer spectroscopy, X-ray diffraction, Faraday balance and vibrating sample magnetometry techniques. All alloys studied exhibit strong magnetic ordering with Curie temperatures close to 900 K. Room temperature Mössbauer measurements revealed distinguished magnetic environments in the samples. The decrease of coercivity with prolonged milling time was attributed to the reduction or averaging of local magnetic anisotropies.     

Nanocrystalline FeAl intermetallics obtained in mechanically alloyed Fe50Al40Ni10 powder

B2-Fe₄₇Al₅₃ intermetallics has been produced by mechanical alloying in a planetary ball mill, using elemental Fe, Al and Ni powder mixture. The microstructural and magnetic properties of the mechanically alloyed Fe₅₀Al₄₀Ni₁₀ powdered samples were investigated by X-ray diffraction and ⁵⁷Fe Mössbauer spectrometry at 300 and 77 K. As resulted from the X-ray diffraction studies, the ordered B2 structure was formed in the Fe₅₀Al₄₀Ni₁₀ powder, together with the bcc α_i-Fe(Al, Ni) (i = 1, 2) solid solutions. Further milling led to a partial disordering of B2-Fe₄₇Al₅₃; it has undergone an order–disorder transition which is characterized by an expansion of the volume Δa₀ (lattice disorder) and a magnetic transition from the paramagnetic to ferromagnetic state which is characterized by strong ferromagnetic interactions in the alloy. The nanocrystalline bcc α_i-Fe(Al, Ni) solid solution was ferromagnetic with a mean crystallite size of 6 nm.     

Mössbauer effect study of fine atomic structure of Fe50Al40Ni10 powders

In the present paper, we discuss the local atomic environment of Fe atoms in the mechanically alloyed Fe₅₀Al₄₀Ni₁₀ powders on the basis of hyperfine data estimated from ⁵⁷Fe Mössbauer spectra. B_hf decreases with increasing milling time due to the diffusion of Al and/or Ni into Fe grains. Nickel atoms did not diffuse inside the first coordination sphere of Fe and if the diffusion takes place the number is not more than one atom. Analyses of P(B_hf), indicate that the high hyperfine field values ranging from 30 to 33 T have to be partially attributed to Fe crystalline nanograins and the presence of the defects in them, the hyperfine field values ranging from 15 to 30 T can be associated to the nanocrystalline bcc Fe(Al, Ni) solid solution while the low hyperfine field values (<15 T) result from Fe atoms located in the disordered grain boundaries.     

Structural, microstructural and hyperfine properties of nanocrystalline iron particles

Nanocrystalline Fe particles were successfully prepared by the mechanical milling process using a high-energy planetary ball mill. The physical properties of the samples were investigated as a function of the milling time, t (in the 0-54 h range) by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray (EDX) and Mössbauer spectroscopy. After 54 h of milling, the lattice parameter increases from 0.28620 (3) nm for the starting Fe powder to 0.28667 (3) nm, the grain size decreases from 110 to 13 nm, while the strain increases from 0.09% to 0.7%. The powder particle morphology was observed by SEM at different stages of milling. For t less than 24 h, the Mössbauer spectra are characterized by one sextet corresponding to the crystalline bcc Fe phase, while for t greater than 24 h, the iron particles exhibit a two-component Mössbauer spectrum due to the presence of two phases: the crystallites bcc Fe phase and the grain-boundary region. The appearance and the increase in intensity of the second sextet with t may indicate that the interfacial region effect increases with milling time due to the grain size reduction and a probable disordered state of the grain boundaries.     

Magnetic and structural studies of mechanically alloyed nanostructured Fe49Co49V2 powders

Nanostructured Fe₄₉Co₄₉V₂ powders were produced by high energy milling at different milling times and then examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The saturation magnetization and coercivity of samples were measured at room temperature by a vibration sample magnetometer (VSM). Structural studies show that as the milling time increases from 0 to 125 h, the average grain size reduces from 130 to about 8-10 nm, while the microstrain increases up to 1.7%. The lattice parameter decreases from 0 to 36 h and then increases up to 125 h. According to the XRD patterns, the formation of intermetallic compound of (Fe, Co)V after about 16 h affects the magnetic properties. The coercivity totally increases up to 61 Oe due to the introduction of microstrain during the milling process. Magnetic measurements reveal that the saturation magnetization has some fluctuations during the milling treatment and finally at 125 h reaches about 180 emu/g     

Atomic structure and magnetic properties of Cu80Co20 nanocrystalline compound produced by mechanical alloying

Direct observation of the atomic structure of the mechanically alloyed Cu₈₀Co₂₀ compounds has been made using the field ion microscope (FIM). Phase composition, defect structure and morphology of material on the atomic scale have been determined. It has been established that the studied material is chemically inhomogeneous, presenting a mixture of two main phases: heterogeneous solid solution of cobalt in copper, and pure cobalt. Phase volume ratios, particle and cluster sizes have been estimated. An evaluation of Co content in Cu---Co solid solution has been made. The width of interfaces in this mechanically alloyed material was revealed to be at least twice the width of phase boundaries in metals and alloys. Superparamagnetism of the compound studied at elevated temperatures and saturation magnetization deficit at low temperatures are discussed on the basis of the above-mentioned structural data.     

Characterization of nanocrystalline FeSiCr powders prepared by ball milling

FeSi₁₀Cr₁₀ powder was mechanically alloyed by high energy planetary ball milling, starting from elemental powders. The microstructural and magnetic properties of the milled powders were characterized by scanning electron microscopy, X-ray diffraction, ⁵⁷Fe Mössbauer spectrometry and a vibratory sample magnetometer.After 3 h of milling, the formation of two bcc solid solutions α-Fe₁ (Si, Cr) and α-Fe₂ (Si, Cr) is observed. Their grain sizes decrease with increase in milling time attaining, at 15 h of milling, 23 and 11 nm, respectively. Mössbauer spectra of the milled powder show the presence of two components. One is a ferromagnetic type with a broad sextuplet. Its distribution of hyperfine field is characterized by high and low hyperfine field’s peaks and a mean value of 26.5 T. The other is a single paramagnetic peak. Its low concentration increases to ∼4% at 15 h of milling. These results can be explained by different atomic environments affected by Si or/and Cr elements, as well as the increased disordered grain boundaries.Magnetic measurements of the milled FeSi₁₀Cr₁₀ alloy powder exhibit a soft ferromagnetic character with a decrease of both magnetization at saturation (Ms) and coercive force (Hc) with milling time attaining values of Ms=151 emu/g and Hc=2500 A/m at 30 h of milling time.     

Synthesis, structural, magnetic and optical properties of nanocrystalline ZnFe2O4

Nanocrystalline zinc ferrite (ZnFe₂O₄) is synthesized by high-energy ball-milling after 12 h from a powders mixture of zinc oxide (ZnO) and hematite (α-Fe₂O₃) with balls to powders mass ratio of 20:1. X-ray diffraction, vibrating sample magnetometer (VSM), the Mössbauer spectrometry and photoluminescence (PL) are used to characterize the samples. Rietveld analysis and VSM measurements show that the powder has an average crystallites size of 10 nm and a ferrimagnetic behavior with a saturation magnetization of 30 emu/g. After annealing at 700 °C, the lattice parameter reduces from 8.448 to 8.427 Å and the sample transforms into a superparamagnetic behavior, which was confirmed as well by the room temperature Mössbauer spectrometry. Different mechanisms to explain the obtained results and the correlation between magnetism and structure are discussed. Finally, the broadband visible emission band is observed in the entire PL spectrum and the estimated energy band gap is about 2.13 eV.     

Recoilless fraction, structural, magnetic and thermal properties of Fe73.5Cu1Nb3Si13.5B9 alloy

Differential scanning calorimetry, X-ray diffraction and room temperature Mössbauer spectrum measurements of Fe_73.5Cu₁Nb₃Si_13.5B₉ (Finemet) alloy have been carried out in order to study its structural and magnetic properties as a function of annealing temperature. The DSC profile of as-quenched Finemet showed two exothermic peaks at 530 and 702 °C, corresponding to two crystallization processes. The Finemet alloy remains amorphous at 450 °C with one broad peak in XRD pattern and one broad sextet in Mössbauer spectrum. When the Finemet alloy was annealed at 550 °C, only well indexed body-center-cubic phase was detected. After being annealed at 650 and 750 °C, the XRD patterns showed the coexistence of α-Fe(Si) and Fe-B intermetallic phases with the increase in XRD peak intensities, indicating the growth of crystallites and the decomposition of Fe_73.5Cu₁Nb₃Si_13.5B₉ alloy at elevated temperatures. The Mössbauer spectra of annealed Finemet alloy could be fitted with 4 or 5 sextets and one doublet at higher annealing temperatures, revealing the appearance of different crystalline phases corresponding to the different Fe sites above the crystallization temperature. The appearance of the nanocrystalline phases at different annealing temperatures was further confirmed by the recoilless fraction measurements.     

Low temperature study of micrometric powder of melted Fe50Mn10Al40 alloy

Melted Fe₅₀Mn₁₀Al₄₀ alloy powder with particle size less than 40 μm was characterized at room temperature by XRD, SEM and XPS; and at low temperatures by Mössbauer spectrometry, ac susceptibility, and magnetization analysis. The results show that the sample is BCC ferromagnetic but with a big contribution of paramagnetic sites, and presents super-paramagnetic and re-entrant spin-glass phases with critical temperatures of 265 and 35 K, respectively. The presence of the different phases detected is due to the disordered character of the sample and the competitive magnetic interactions. The obtained values of the saturation magnetization and the coercive field as a function of temperature present a behavior which indicates a ferromagnetic phase. However, the behavior of the FC curve and that of the coercive field as a function of temperature suggest that the dipolar magnetic interaction between particles contributes to the internal magnetic field in the same way as was reported for nanoparticulate powders.     

Structure and magnetic properties of nanocrystalline Fe75Si25 powders prepared by mechanical alloying

Nanocrystalline Fe₇₅Si₂₅ powders were prepared by mechanical alloying in a planetary ball mill. The evolution of the microstructure and magnetic properties during the milling process were studied by X-ray diffraction, scanning electron microscope and vibrating sample magnetometer measurements. The evolution of non-equilibrium solid solution Fe (Si) during milling was accompanied by refinement of crystallite size down to 10 nm and the introduction of high density of dislocations of the order of 10¹⁷ m⁻². During the milling process, Fe sites get substituted by Si. This structural change and the resulting disorder are reflected in the lattice parameters and average magnetic moment of the powders milled for various time periods. A progressive increase of coercivity was also observed with increasing milling time. The increase of coercivity could be attributed to the introduction of dislocations and reduction of powder particle size as a function of milling time.     

Simultaneous variations of microstructure and magnetic properties of Ni58Fe12Zr20B10 nanostructure/amorphous alloy prepared by mechanical alloying

This study aims to evaluate magnetic and micro-structural properties of amorphous/nanocrystalline mechanically alloyed Ni₅₈Fe₁₂Zr₂₀B₁₀ powders with ball-milling time up to 190 h. Structural, micro-structural and thermal evaluations of the milled powders were carried out by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM) and differential scanning calorimetry (DSC) methods. Magnetic properties were also measured by a vibrating sample magnetometer (VSM) instrument. Results showed that the amorphous phase reached maximum value of 95% and the crystallite size was about 3 nm at the end of the milling. Magnetization saturation (M_s) decreased slightly and coercivity (H_c) reached to the highest value at 72 h of the milling time. At the 190 h of milling, the coercivity and saturation magnetization reached 18 Oe and 20 emu/g, respectively. While, after an appropriate amount of heat treatment, these two variables became approximately 2 Oe and 32 emu/g.     

Hyperfine interactions, structure and magnetic properties of nanocrystalline Co–Fe–Ni alloys prepared by mechanical alloying

Mechanical alloying method was used to prepare nanocrystalline Co₅₀Fe₄₀Ni₁₀, Co₅₂Fe₂₆Ni₂₂ and Co₆₅Fe₂₃Ni₁₂ alloys. X-ray diffraction proved that during milling Co–Fe-based solid solution with b.c.c. lattice was formed in the case of Co₅₀Fe₄₀Ni₁₀, while for Co₅₂Fe₂₆Ni₂₂ and Co₆₅Fe₂₃Ni₁₂ compositions Co–Ni-based solid solutions with f.c.c. lattice were obtained. Mössbauer spectroscopy revealed similar values of the average hyperfine magnetic fields for all alloys, e.g. 32.17, 32.24 and 31.21 T for Co₅₀Fe₄₀Ni₁₀, Co₅₂Fe₂₆Ni₂₂ and Co₆₅Fe₂₃Ni₁₂ alloys, respectively. Magnetization measurements allowed to determine the effective magnetic moment, Curie temperature, saturation magnetization and coercive field for the obtained alloys.     

Research on Zr50Al15−xNi10Cu25Yx amorphous alloys prepared by mechanical alloying with commercial pure element powders

Amorphous Zr₅₀Al_15−xNi₁₀Cu₂₅Y_x alloy powders were fabricated by mechanical alloying at low vacuum with commercial pure element powders. The effects on glass forming ability of Al partial substituted by Y in Zr₅₀Al₁₅Ni₁₀Cu₂₅ and thermal stability of Si₃N₄ powders addition were investigated. The as-milled powders were characterized by X-ray diffraction, scanning electron microscopy and differential scanning calorimeter. The results show that partial substitution of Al can improve the glass forming ability of Zr₅₀Al₁₅Ni₁₀Cu₂₅ alloy. Minor Si₃N₄ additions raise the crystallization activation energy of the amorphous phase and thus improve its thermal stability.     

Structural transformations and magnetic properties of Fe60Pt15B25 and Fe60Pt25B15 nanocomposite alloys

Structural and magnetic properties of two rapidly solidified and post-annealed Fe₆₀Pt₁₅B₂₅ and Fe₆₀Pt₂₅B₁₅ alloys are compared. The as-quenched Fe₆₀Pt₁₅B₂₅ ribbon was fully amorphous whereas in the Fe₆₀Pt₂₅B₁₅ alloy the amorphous phase coexists with an fcc FePt disordered solid solution. Differential scanning calorimetry curves of both alloys reveal a single exothermal peak with onset temperatures of 873 and 847 K for Fe₆₀Pt₁₅B₂₅ and Fe₆₀Pt₂₅B₁₅, respectively. Magnetically hard, tetragonal ordered L1₀ FePt and magnetically soft Fe₂B nanocrystalline phases were formed due to the annealing of the alloys, as indicated by X-ray diffraction and Mössbauer spectroscopy measurements. Two-phase behavior was detected in the temperature dependence of magnetization of the annealed samples. A magnetic hardening was observed for all annealed ribbons. Magnetic properties of the annealed alloys, studied by hysteresis loop measurements, were related to the differences in the relative fractions of the hard and soft magnetic phases calculated from Mössbauer spectra. The alloy with 25 at% Pt exhibits better hard magnetic properties (H_c=437 kA/m, M_r/M_s=0.74) than the alloy with smaller Pt content (H_c=270 kA/m, M_r/M_s=0.73) mainly due to the larger abundance of the ordered tetragonal FePt phase.     

Nd28Fe66B6/Fe50Co50双层纳米复合膜的结构和磁性

利用磁控溅射法制备了Nd₂₈Fe₆₆B₆/Fe_{50Co50 双层纳米复合磁性薄膜，研究了其结构和磁性.经873K退火处理15min 后，利用x射线衍射仪测定薄膜晶体结构，采用俄歇电子能谱仪估算薄膜厚度和超导量子干 涉仪测量其磁性.磁性测量表明，1)该系列薄膜具有垂直于膜面的磁各向异性.从起始磁化曲 线和小回线的形状特征可知，矫顽力机制主要是由畴壁钉扎控制.2)对于固定厚度（10nm） 层的硬磁相Nd-Fe-B和不同厚度（dFeCo=1—100nm）层软磁相FeCo双层纳米复合 膜,剩磁随软磁相FeCo 厚度的增加快速增加，而矫顽力则减少.当dFeCo=5nm 时 ，最大磁能积达到160×１０^３A/m.磁滞回线的单一硬磁相特征说明，硬磁相Nd -Fe-B层和软磁相FeCo层之间的相互作用使两相很好地耦合在一起.剩磁和磁能积的提高是由 于两相磁性交换耦合所致. 关键词： Nd-Fe-B/FeCo双层纳米复合膜 交换耦合 磁性增强}     

Studies on Structural, Magnetic and Thermal Properties of xFe2TiO4-(1−x)Fe3O4 (0≤x≤1) Pseudo-binary System

The xFe₂TiO₄-(1−x)Fe₃O₄ pseudo-binary systems (0≤x≤1) of ulvöspinel component were synthesized by solid-state reaction between ulvöspinel Fe₂TiO₄ precursors and commercial Fe₃O₄ powders in stochiometric proportions. Crystalline structures were determined by X-ray powder diffraction (XRD) and it was found that the as-obtained titanomagnetites maintain an inverse spinel structure. The lattice parameter a of synthesized titanomagnetite increases linearly with the increase in the ulvöspinel component. ⁵⁷Fe room temperature Mössbauer spectra were employed to evaluate the magnetic properties and cation distribution. The hyperfine magnetic field is observed to decrease with increasing Fe₂TiO₄ component. The fraction of Fe²⁺ in both tetrahedral and octahedral sites increases with the increase in Ti⁴⁺ content, due to the substitution and reduction of Fe³⁺ by Ti⁴⁺ that maintains the charge balance in the spinel structure. For x in the range of 0 ≤x≤0.4, the solid solution is ferrimagnetic at room temperature. However, it shows weak ferrimagnetic and paramagnetic behavior for x in the range of 0.4<x≤0.7. When x>0.70, it only shows paramagnetic behavior, with the appearance of quadrupole doublets in the Mössbauer spectra. Simultaneous differential scanning calorimetry and thermogravimetric analysis (DSC-TGA) studies showed that magnetite is not stable, and thermal decomposition of magnetite occurs with weight losses accompanying with exothermic processes under heat treatment in inert atmosphere.     

Structural transformations of Fe81B13Si4C2 amorphous alloy induced by heating

Thermal stability and crystallization of the Fe₈₁B₁₂Si₄C₂ alloy were investigated in the temperature range 25-700 °C by the XRD and Mössbauer analysis. It was shown that on heating the as-prepared amorphous Fe₈₁B₁₂Si₄C₂ alloy undergoes thermal stabilization through a series of structural transformations involving the process of stress-relieving (temperature range 200-400 °C), followed by a loss of ferromagnetic properties (Curie temperature at 420 °C) and finally crystallization (temperature range 450-530 °C). The process of crystallization begins by formation of two crystal phases: Fe₃B and subsequently Fe₂B, as well as a solid solution α-Fe(Si). With increase in annealing temperature, the completely crystallized alloy involved only two phases, Fe₂B and solid solution α-Fe(Si).XRD patterns established a difference in phase composition and size of the formed crystallites during crystallization depending on the side (fishy or shiny) of the ribbon. The first nuclei of the phase α-Fe₃Si were found on the shiny side by XRD after heat treatment even at 200 °C but the same phase on the fishy side of ribbon was noticed after heat treatment at 450 °C. The largest difference between the contact and free surface was found for the Fe₂B phase crystallized by heating at 700 °C, showing the largest size of crystallites of about 130 nm at 700 °C on the free (shiny) surface.     

Crystallization kinetics of the Fe40Ni38Mo4B18 amorphous alloy

X-ray diffraction (XRD) and Mössbauer spectroscopy were used to study the annealing of the Fe₄₀Ni₃₈Mo₄B₁₈ amorphous alloy. The samples were isothermally annealed in the 858–878 K temperature range several times. Two crystalline phases were observed in the annealed samples: FeNi₃ and (Fe, Ni, Mo)₂₃B₆. Preliminary results indicate that assuming a linear relationship between the area under the main XRD peak associated with the FeNi₃ phase and its volume fraction, this can be fitted to a Johnson–Mehl–Avrami equation with an exponent n close to 1.0. Mössbauer results show a broad magnetic hyperfine field distribution in as-received samples and, consistent with XRD results, a sextet attributed to precipitates of FeNi₃ (B_hf=29.5 T) for long annealing times.     

Influence of milling time on the structural, microstructural and magnetic properties of mechanically alloyed Ni58Fe12Zr10Hf10B10 nanostructured/amorphous powders

This paper investigates structural, microstructural and magnetic properties of amorphous/nanocrystalline Ni₅₈Fe₁₂Zr₁₀Hf₁₀B₁₀ powders prepared by high energy milling. Ball milling of Ni, Fe, Zr, Hf and B leads to alloying of the element powders at 120 h. The results show that at 190 h the amorphous content is at the highest level and the grain size is about 2 nm. The magnetic measurements reveal that the coercivity and the saturation magnetization reach about 20 Oe and 30 emu/g at 190 h and become approximately 5 Oe and 40 emu/g after a suitable heat treatment, respectively.