Field and temperature induced colossal strain in Gd5(SixGe1−x)4

Gd₅(Si_xGe_1−x)₄, known for its giant magnetocaloric effect, also exhibits a colossal strain of the order of 10,000 ppm for a single crystal near its coupled first-order magnetic-structural phase transition, which occurs near room temperature for the compositions 0.41≤x≤0.575. Such colossal strain can be utilised for both magnetic sensor and actuator applications. In this study, various measurements have been carried out on strain as a function of magnetic field strength and as a function of temperature on single crystal Gd₅Si₂Ge₂ (x=0.5), and polycrystalline Gd₅Si_1.95Ge_2.05 (x=0.487) and Gd₅Si_2.09Ge_1.91 (x=0.52). Additionally a giant magnetostriction/thermally induced strain of the order of 1800 ppm in polycrystalline Gd₅Si_2.09Ge_1.91 was observed at its first order phase transition on varying temperature using a Peltier cell without the use of bulky equipment such as cryostat or superconducting magnet.     

Structural,electronic and optical properties of CdxZn1 − xS alloys from first-principles calculations

Structural, electronic and optical properties as well as structural phase transitions of ternary alloy Cd_xZn_1 − xS have been investigated using the first-principles calculations based on the density functional theory. We found that the crystal structure of Cd_xZn_1 − xS alloys transforms from wurtzite to zinc blende as Cd content of x=0.83$x=0.83$. Effect of Cd content on electronic structures of Cd_xZn_1 − xS alloys has been studied. The bandgaps of Cd_xZn_1 − xS alloys with wurtzite and zinc blende structures decrease with the increase of Cd content. Furthermore, dielectric constant and absorption coefficient also have been discussed in detail.     

Low-voltage cathodoluminescence property of Li-doped Gd2−xYxO3:Eu

Cathodoluminescent (CL) spectra of Li-doped Gd_2−xY_xO₃:Eu³⁺ solid-solution (0.0?x?0.8) were investigated at low voltages (300 V-1 kV). The CL intensity is maximum for the composition of x=0.2 and gradually reduces with increasing the amount of substituted Y content. In particular, small (∼100 nm) particles of Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ are obtained by firing the citrate precursors at only 650°C for 18 h. Relative red-emission intensity at 300 V of this phosphor is close to 180% in comparison with that of commercial red phosphor Y₂O₃:Eu³⁺. An increase of firing temperature to 900°C results in 400-600 nm sized spherical particles. At low voltages (300-800 V), the CL emission of 100 nm sized particles is much stronger than that of 400-600 nm sized ones. In contrast, the larger particles exhibit the higher CL emission intensity at high voltages (1-10 kV). Taking into consideration small spherical morphology and effective CL emission, Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ appears to be an efficient phosphor material for low voltage field emission display.     

Structural and electrical characterization of SxSe100−x thin films

Thin films of samples of the glassy S_xSe_100−x system with 0 ≤ x ≤ 7.28 have been prepared by thermal evaporation technique at room temperature (300 K). X-ray investigations show that the structure of pure selenium (Se) does change seriously by the addition of small amount of sulphur S ≤7.28%. The lattice parameters were determined as a function of sulphur content. Results of differential thermal analysis (DTA) of the glassy compositions of the system S_xSe_100−x were discussed. The characteristic temperatures (T_g, T_c and T_m) were evaluated. Dark electrical resistivities, ρ, of S_xSe_100−x thin films with different thicknesses from 100 to 500 nm, were measured in the temperature range from 300 to 423 K. Two distinct linear parts with different activation energies were observed. The variation of electrical resistivity of examined compositions has been discussed as a function of the film thickness, temperature and the sulphur content. The application of Mott model for the phonon assisted hopping of small polarons gave the same two activation energies obtained from the resistivity temperature calculations.     

Magnetic properties of YFe12−xMox compounds and magnetocaloric effect of YFe9.5Mo2.5

The characterization and magnetic properties of YFe_12−xMo_x (x=2.0, 2.5 and 3.0) with the ThMn₁₂-type structure, and the magnetocaloric effect of YFe_9.5Mo_2.5 were investigated. A directional growth was observed in YFe₁₀Mo₂ alloy. A broad peak in the zero-field-cooling (ZFC) magnetization curve of the YFe_12−xMo_x compounds is ascribed to the existence of ferromagnetic clusters with different site moments and scattered orientations of the moments. The broad range of the peak is reduced with increasing Mo content. A weak peak is observed near 190 K in the ZFC curve of YFe₉Mo₃, which is associated with the 8i sites being mostly occupied by Mo atoms. YFe_9.5Mo_2.5 has a magnetic entropy change of −1.09 J/kg K for a field change of 5 T at 277 K.     

Optoelectronic properties of GaAs1−xPx alloys under the influence of temperature and pressure

This work is concerned with the dependence of the electronic energy band structures for GaAs_1−xP_x alloys on temperature and pressure that is based on local empirical pseudo-potential method. The band structures of GaAs_1−xP_x alloys were calculated in the virtual crystal approximation using the EPM which incorporates compositional disorder as an effective potential.     

Hard magnetic properties of melt-spun Co82Zr18−xTix alloys

The phases and magnetic properties of Co-Zr-Ti melt-spun ribbons were studied by XRD analysis and magnetic measurements. The optimal magnetic properties of Ms=59.0 emu/g, Mr=4.0 kG, Hc=2.9 kOe, and (BH)_max=3.0 MGOe were obtained in Co₈₂Zr₁₄Ti₄ ribbons produced at a wheel speed of 30 m/s. In this work, we found that Ti was one of the few large atomic radius elements, which could improve hard magnetic properties of Co-Zr alloy.     

Molecular dynamics simulations on local structure and diffusion in liquid TixAl1−x alloys

The microscopic structure and dynamics of liquid Ti_xAl_1-x alloys together with pure liquid Ti and Al metals were investigated by means of molecular dynamics simulations. This work gives the structural properties, including pair-correlation function, bond-angle distribution function, HA and Voronoi indices, and their composition dependence. The dynamical properties have also been studied. The calculated pair-correlation function, bond-angle distribution function, and HA and Voronoi indices suggest that the stoichiometric composition Ti_0.75Al_0.25 exhibits a different local structure order compared with other concentrations, which help us understand the appearance of the minimum diffusion coefficient at this composition. These results indicate that the mobility of atoms strongly depends on their atomic local structure.     

Structural and magnetic properties in Bi1−xRxFeO3 (x=0-1, R=La, Nd, Sm, Eu and Tb) polycrystalline ceramics

A series of rare-earth doped BiFeO₃ samples, Bi_1−xR_xFeO₃ (x=0-1, R=La, Nd, Sm, Eu and Tb), were prepared in this work. X-ray diffraction analysis showed that the structure of rare-earth doped BiFeO₃ was transformed from rhombohedral lattice to orthorhombic one by increasing x. The lattice constants and unit-cell volume decreased with the increasing of the doping content, while both the Néel temperature and magnetization were enhanced. A magnetic phase transition was observed at about 35 K for BiFeO₃. The variation of the magnetization with temperature depended on applied field strength and magnetizing history, which was explained according to the antiferromagnetic exchange interaction between Fe and R sites in Bi_1−xR_xFeO₃(x>0). The magnetocrystalline anisotropy contributed by Fe sublattice gave rise to a large coercivity in Bi_xNd_1−xFeO₃ with an orthorhombic structure.     

Conductivity and sintering property of LaNi1 − xFexO3 ceramics prepared by Pechini method

Preparation of LaNi_1 − xFe_xO₃, which is one of the candidate materials of solid oxide fuel cell cathode, current collecting layer and interconnect coating was examined with Pechini method and solid state reaction method. Single phase LaNi_1 − xFe_xO₃ with large Ni content has successfully been prepared by low temperature sintering as 750 °C with Pechini method, whereas large amount of raw materials has remained with solid state reaction method by sintering at the same temperature. It can be ascribed to more homogenous cation distribution in raw powder material prior to sintering with Pechini method. It has also been revealed that LaNi_1 − xFe_xO₃ with x lower than 0.3 is thermodynamically unstable in air above 1000 °C. LaNi_0.6Fe_0.4O₃ showed superior property as cathode material with high electrical conductivity, thermodynamic stability and appropriate sintering property.     

Synthesis and ferroelectric properties of bismuth layer-structured (Bi7−xSrx)(Fe3−xTi3+x)O21 solid solutions

Bismuth layer-structured (Bi_7−xSr_x)(Fe_3−xTi_3+x)O₂₁ (BSFT) ceramics were synthesized and the ferroelectric properties and crystal structure were investigated. X-ray powder diffraction profiles and refinement of the lattice parameters indicated single phase BSFT was obtained in the composition range 0-1.5. The lattice parameter b of BSFT remained almost constant, while a slight decrease in the lattice parameter a was observed by the Sr and Ti substitution for Bi and Fe, respectively, which indicated an increase in the orthorhombicity. The dependence of the BSFT lattice parameter on temperature implied a phase transition from the orthorhombic to the tetragonal phase, which was in good agreement with the Curie temperature. The remnant polarization P_r, of BSFT was significantly improved by the Sr and Ti substitution for Bi and Fe, and ranged from 9 to 16 μC/cm², although no remarkable variation in the coercive field E_c was observed. As a result, a well-saturated P-E hysteresis loop of BSFT ceramic was obtained at x=0.5 with a P_r of 30 μC/cm at an applied voltage of 280 kV/cm.     

Temperature-programmed surface reaction (TPSR) of CH4 synthesis by PdxNi100−x nanoparticles

A series of Pd_xNi_100−x nanoparticles were prepared by the co-precipitation method and analyzed using a temperature-programmed surface reaction (TPSR) of their methanation reactions. ESCA measurement suggested that the as-prepared Pd-Ni alloys had Pd-core/Ni-shell structure. Surface Pd segregation occurred during H₂ reduction and resulted in a surface composition close to the nominal value. The TPSR experiments were performed by pre-adsorption of CO with H₂ to form methane. The peak temperature of methanation increased as Pd content increased, indicating that a methanation reaction is favored on Ni and Ni-rich alloy nanoparticles. For physical mixtures of Pd and Ni nanoparticles, methanation behaviors is similar to those of alloy nanoparticles; but the methanation temperatures of physical mixtures are always higher than those of alloy nanoparticles. This may be due to the formation of a Pd-enriched alloy surface layer during reduction in H₂ at 400 °C, or because the CO molecules adsorbed on the Pd sites spill over onto the Ni sites for methanation. Using TPSR technique and measuring methanation temperature, the top-most surface of such bimetallic nanoparticles can be probed.     

Magnetic properties of the Lu2Fe17−xMnx single crystals

Magnetic properties of the single-crystalline Lu₂Fe_17−xMn_x compounds, in which x=0, 0.5, and 2, with the Th₂Ni₁₇-type crystal structure are reported. The Lu₂Fe_17−xMn_x compounds with x=0 and 0.5 are ferromagnets at low temperatures and antiferromagnets at high temperatures. The compound with x=2 is always a ferromagnet. The easy-plane magnetic anisotropy in the Lu₂Fe_17−xMn_x ferromagnets drastically weakens with increase in Mn content up to x=2. The temperature dependence of the first magnetic anisotropy constant was obtained and compared with the single-ion model prediction.     

Nanoscale semiconductor Pb1−xSnxSe (x = 0.2) thin films synthesized by electrochemical atomic layer deposition

In this paper the fabrication and characterization of IV-VI semiconductor Pb_1−xSn_xSe (x = 0.2) thin films on gold substrate by electrochemical atomic layer deposition (EC-ALD) method at room temperature are reported. Cyclic voltammetry (CV) is used to determine approximate deposition potentials for each element. The amperometric I-t technique is used to fabricate the semiconductor alloy. The elements are deposited in the following sequence: (Se/Pb/Se/Pb/Se/Pb/Se/Pb/Se/Sn …), each period is formed using four ALD cycles of PbSe followed by one cycle of SnSe. Then the deposition manner above is cyclic repeated till a satisfactory film with expected thickness of Pb_1−xSn_xSe is obtained. The morphology of the deposit is observed by field emission scanning electron microscopy (FE-SEM). X-ray diffraction (XRD) pattern is used to study its crystalline structure; X-ray photoelectron spectroscopy (XPS) of the deposit indicates an approximate ratio 1.0:0.8:0.2 of Se, Pb and Sn, as the expected stoichiometry for the deposit. Open-circuit potential (OCP) studies indicate a good p-type property, and the good optical activity makes it suitable for fabricating a photoelectric switch.     

Population analysis solution to hardness enhancement in TiCxN1−x

We investigated the hardness enhancement in titanium carbonitrides (TiC_xN_1−x) by the population analysis method based on first-principles calculations. Populations for bonds TiC and TiN in TiC_xN_1−x (0.25<x<0.75) are all positive. The enhanced hardness for titanium carbonitrides is well explained by overlap population analysis. Intrinsic hardness of TiC_xN_1−x has been calculated based on the obtained overlap populations. The calculated results are in good agreement with the available experimental data.     

Structure and electrical properties of Bi5GexSe95−x thin films

Bi₅Ge_xSe_95−x (30, 35, 40 and 45 at.%) thin films of thickness 200 nm were prepared on glass substrates by the thermal evaporation technique. The influence of composition and annealing temperature, on the structural and electrical properties of Bi₅Ge_xSe_95−x films was investigated systematically using X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX). The XRD patterns showed that the as-prepared films were amorphous in nature with few tiny crystalline peaks of relatively low intensity for 30 and 45 at.% and the Bi₅Ge₄₀Se₅₅ annealed film was polycrystalline. The chemical composition of the Bi₅Ge₃₀Se₆₅ film has been checked using energy dispersive X-ray spectroscopy (EDX). The electrical conductivity was measured in the temperature range 300-430 K for the studied compositions. The effect of composition on the activation energy (ΔE) and the density of localized states at the Fermi level N(E_F) were studied, moreover the electrical conductivity was found to increase with increasing the annealing temperature and the activation energy was found to decrease with increasing the annealing temperature. The results were discussed on the basis of amorphous-crystalline transformations.     

Electronic structure and optical properties of CdSexTe1−x mixed crystals

The band structure and optical properties of the CdSe_xTe_1−x ternary mixed crystals have been studied using the pseudopotential formalism under an improved virtual crystal approximation approach. Quantities such as, energy gaps, band-gap bowing parameters, electron effective mass and dielectric constants are calculated. Our results agree well with the available data in the literature. The composition dependence of all studied quantities has been expressed by quadratic polynomial forms.     

Magnetic properties and room-temperature magnetocaloric effect in the doped antipervoskite compounds Ga1−xAlxCMn3 (0≤x≤0.15)

We report the effects of Al doping on the structure, magnetic properties, and magnetocaloric effect of antiperovskite compounds Ga_1−xAl_xCMn₃ (0≤x≤0.15). Partial substitutions of Al for Ga enhance the Curie temperature (from 250 K for x=0.0 to 312 K for x=0.15) and the saturation magnetization. On increasing the doping level x, the maximum values of the magnetic entropy change (−ΔS_M) decreases while the temperature span of −ΔS_M vs. T plot broadens. Furthermore, the relative cooling power (RCP) is also studied. For 20 kOe, the RCP value tends to saturate at a high doping level (for x=0.12, 119 J/kg at 296 K). However, at 45 kOe, the RCP value increases quickly with increasing x (for x=0.15, 293 J/kg at 312 K). Considering the relatively large RCP and inexpensive raw materials, Ga_1−xAl_xCMn₃ may be alternative candidates for room-temperature magnetic refrigeration.     

Short-range order analysis and some physical properties of InxSe1−x glasses

Bulk In_xSe_1−x (with x=5-25 at%) glasses were prepared using the melt-quench technique. Short range order(SRO) was examined by the X-ray diffraction using Cu(k_α) radiation in the wave vector interval 0.28≤k≤6.5 A⁰⁻¹.The SRO parameters have been obtained from the radial distribution function. The inter-atomic distance obtained from the first and second peak are r₁=0.263 and r₂=0.460 nm, which is equivalent In-Se and Se-Se bond length. The fundamental structural unit for the studied glasses is In₂Se₃ pyramid. Using the differential scanning calorimetry (DSC), the crystallization mechanism of In_xSe_1−x chalcogenide glass has been studied. The glass transition activation energy (E_g) is 289±0.3 kj/mol.There is a correlation amongst the glass forming ability, bond strength and the number of lone pair electrons. The utility of the Gibbs-Di Marzio relation was achieved by estimating T_g theoretically.     

Luminescent properties of HTP AgGd1−xW2O8:Eux and AgGd1−x(W1−yMoy)2O8:Eux phosphor for white LED

Intense red phosphors, AgGd_1−xEu_x(W_1−yMo_y)₂O₈ (x=0.0-1.0, y=0.0-1.0), have been synthesized through traditional solid-state reaction and characterized by X-ray diffraction (XRD) and photoluminescence (PL). XRD results reveal that AgGd_1−xEu_xW₂O₈ synthesized at 1000 °C has a tetragonal crystal structure, which is named as high temperature phase (HTP) AgGdW₂O₈. All phosphors compositions with Eu³⁺ show red and green emission on excitation either in the charge-transfer or Eu³⁺ levels. Analysis of the emission spectra with different Eu³⁺ concentrations reveal that the optimum dopant concentration for Eu³⁺ is x=0.6 in the HTP AgGd_1−xEu_xW₂O₈ (x=0.0-1.0). Studies on the AgGd_0.4Eu_0.6(W_1−yMo_y)₂O₈ (y=0.0-1.0) and AgGd_1−xEu_x(W_0.7Mo_0.3)₂O₈ (x=0.0-1.0) show that the emission intensity is maximum for compositions with y=0.3 and x=0.5, respectively, and a decrease in emission intensity is observed for higher y or x values. The Mo⁶⁺ and Eu³⁺ co-doped AgGd(WO₄)₂ phosphors show higher emission intensity in comparison with the singly Eu³⁺-doped AgGd(WO₄)₂ in UV region. The intense emission of the tungstate/molybdate phosphors under 394 and 465 nm excitations, respectively, suggests that these materials are promising candidates as red-emitting phosphors for near-UV/blue GaN-based white LED for white light generation.