One-step preparation of organometal/Fe3O4 hybrid microspheres and their electromagnetic properties

Novel organometal/Fe₃O₄ hybrid microspheres were prepared from bisphthalonitrile-benzoxine resin containing ferrocene (FPNBZ) and FeCl₃·6H₂O via a one-step solvent-thermal method. The phase structure, composition and morphology of as-prepared hybrid microspheres were characterized by X-ray powder diffraction, Fourier transform infrared spectrophotometer and scanning electron microscopy. The results revealed that crystallinity, dispersity and size of hybrid microspheres can be controlled by altering the reaction parameters. Density measurement showed that the density is decreased with increasing FPNBZ concentration in the hybrid materials. Electromagnetic properties of the FPNBZ/Fe₃O₄ hybrid microspheres were measured at 2-18 GHz. The electromagnetic measurement indicated that the resonance peaks of complex permittivity, complex permeability, dielectric loss and magnetic loss were shifted to the high frequencies, with the increasing amount of FPNBZ. The as-prepared hybrid materials are believed to have broad applications both in microwave absorption materials in a wide frequency range and in biomedical fields.     

Preparation of poly(styrene-glucidylmethacrylate)/Fe3O4 composite microspheres with high magnetite contents

Magnetic polymer composite microspheres with high magnetite contents were prepared by dispersion polymerization of styrene (St) and glucidylmethacrylate (GMA), in which Fe₃O₄ nanoparticles were co-stabilized by oleic acid and silane surfactants. The microstructure of the composite microspheres was characterized by Fourier transform infrared (FTIR) spectrometry, X-ray diffraction (XRD) and transmission electron microscopy (TEM). Results demonstrated the presence of a hybrid morphology with organic polymer-encapsulated inorganic particles. Subsequently, thermogravimetric analysis (TGA) and vibrating sample magnetometry (VSM) were used to evaluate the magnetite content of the microspheres. It was found that an accordant magnetite content of about 70 wt%, could be obtained for the magnetic polymer microspheres, a value significantly higher than those reported thus far. The possible mechanism for the formation of the microspheres was proposed.     

Growth of single-crystal magnetite nanowires from Fe3O4 nanoparticles in a surfactant-free hydrothermal process

Single-crystal magnetite nanowires with average diameter of ca. 20 nm and length of up to several micrometers were prepared by a simple alkaline surfactant-free hydrothermal process. The crystallinity, purity, morphology, and structural features of the as-prepared magnetite nanowires were investigated by powder X-ray diffraction, transmission electron microscopy (TEM) and selected area electron diffraction. The composition and length of nanowires depends on the pH, with higher pH favoring longer nanowires composed entirely of Fe₃O₄. A mechanism for nanowire growth is proposed.     

Efficient field emission from coiled carbon nano/microfiber on copper substrate by dc-PECVD

Crystalline coiled carbon nano/micro fibers in thin film form have been synthesized via direct current plasma enhanced chemical vapor deposition (PECVD) on copper substrates with acetylene as a carbon precursor at 10 mbar pressure and 750 °C substrate temperature. The as-prepared samples were characterized by X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM) and high resolution transmission electron microscopy (HRTEM). XRD pattern as well as selected area electron diffraction (SAED) pattern showed that the samples were crystalline in nature. SEM and HRTEM studies showed that as synthesized coiled carbon fibers are having average diameter ∼100 nm and are several micrometers in length. The as-prepared samples showed moderately good electron field emission properties with a turn-on field as low as 1.96 V/μm for an inter-electrode distance 220 μm. The variation of field emission properties with inter-electrode distance has been studied in detail. The field emission properties of the coiled carbon fibrous thin films are compared with that of crystalline multiwalled carbon nanotubes and other carbon nanostructures.     

Controllable one-step synthesis of magnetite/carbon nanotubes composite and its electrochemical properties

Magnetite nanocrystals are deposited on carbon nanotubes by a reflux method in diethylene glycol. The morphological characterization proves that magnetite nanocrystals are decorated on the external surfaces of carbon nanotubes. The crystal size of magnetite nanocrystals can be readily tuned by adjusting the content of sodium acetate, but the content of sodium acetate has little effect on the amount of magnetite. The magnetite/carbon nanotubes composites exhibit an initial capacity as high as 840 mAh g⁻¹ and an excellent cycling performance for lithium storage. The reversible capacity, as high as 390 mAh g⁻¹, can be maintained after 75 charge/discharge cycles. The research has potential implications for the application of magnetite/carbon nanotubes composites as anode materials of lithium ion batteries.     

Selective growth of carbon nantoubes on SiO2/Si substrate

Three-step raising temperature process was employed to fabricate carbon nanotubes by pyrolysis of ferrocene/melamine mixtures on silica and single crystalline silicon wafers respectively. Then the morphologies, structures and compositions of obtained carbon nanotubes are investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray spectroscope (EDX) and electron energy-loss spectroscopy (EELS). TEM and SEM observation shows that on silica substrate, high-oriented carbon nanotube can grow compactly to form continuous film on both frontal and cross-section surfaces, but on silicon substrate, only can form on cross-section surface. These carbon nanotubes have much irregular cup-like structure, and with outer diameter varying from 25 nm to 35 nm. At the top end of carbon nanotube there is a catalyst particle. EDX analysis reveals that the particle are iron cluster, and EELS spectrum indicates that the nanotube is composed of pure carbon. Finally, the effect of substrate surface roughness on the growth behavior of carbon nanotubes has been discussed.     

Fabrication and characterization of magnetic Fe3O4-CNT composites

Carbon nanotubes (CNTs) decorated with magnetite nanoparticles on their external surface have been fabricated by in situ solvothermal method, which was conducted in benzene at 500 °C with ferrocene and CNTs as starting reagents. The as-prepared composites were characterized using XRD, FTIR, SEM and TEM. It has been found that the amount of magnetite nanoparticles deposited on the CNTs can be controlled by adjusting the initial mass ratio of ferrocene to CNTs. The Fe₃O₄-CNT composites display good ferromagnetic property at room temperature, with a saturation magnetization value (M_s) of 32.5 emu g⁻¹ and a coercivity (H_c) of 110 Oe.     

Synthesis and characterization of Pd-on-Pt and Au-on-Pt bimetallic nanosheaths on multiwalled carbon nanotubes

The authors have successfully synthesized Pd-on-Pt (thickness: 12 nm) and Au-on-Pt bimetallic nanosheaths on multiwalled carbon nanotubes (MWCNTs) via a seed-mediated growth approach. Pt nanoparticles as seeds were pre-deposited on MWCNTs with uniform distribution followed by the successive seed-mediated growth of metal atoms reduced by a weak reducing agent, ascorbic acid. The essential role of pre-deposited nanoseed particles on MWCNTs was demonstrated. The as-prepared materials were characterization by transition electron microscopy, energy-dispersive X-ray spectroscopy, and element mapping tools. The current strategy extends the classical seed-mediated growth method to prepare bimetallic nanosheath on MWCNT support.     

Preparation, structure and photo-catalytic performances of hybrid Bi2SiO5 modified Si nanowire arrays

Bi₂SiO₅ modified Si nanowire array films were fabricated as photo-catalysts via dip-coating Bi(NO₃)₃ on silver-assisted electroless wet chemical etching Si nanowires and subsequently annealing. The structures and morphologies of as-prepared samples are characterized by X-ray diffraction, Fourier transform infrared spectrum, scanning electron microscopy and transmission electron microscopy. The results of photocatalytic experiments indicated that the Bi₂SiO₅ modified Si nanowire arrays benefit the improvement for efficient electron-hole separation and photo-catalytic stability, thereby possessing superior photo-degradation performance. These hybrid nanowire arrays will be promising materials for photo-catalysts and degradation agents.     

Growth of Y-junction bamboo-shaped CNx nanotubes on GaAs substrate using single feedstock

Nitrogen-doped Y-junction bamboo-shaped carbon nanotubes were synthesized by chemical vapor deposition of monoethanolamine/ferrocene mixture on GaAs substrate at 950 °C. The use of monoethanolamine as the C/N feedstock simplifies the experimental arrangement by producing ammonia during the growth process. The structure, morphology and graphitization of as-grown nitrogen-doped carbon nanotubes (CN_x) were examined by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman spectroscopy analysis. TEM analysis indicates that nanotubes have a bamboo-like structure. The nitrogen concentration on as-grown CN_x nanotube was found to be 7.8 at.% by X-ray photoelectron spectroscopy (XPS) analysis. XPS analysis also indicated that there are two different types of nitrogen atoms (pyridinic and graphitic) in these materials. The possible growth mechanism of formation of Y-junction CN_x nanotubes was briefly discussed. Field emission measurement suggested that as-grown CN_x nanotubes are excellent emitters with turn-on and threshold fields of 1.6 and 2.63 V/μm, respectively. The result indicated that monoethanolamine proves to be an advantageous precursor to synthesize Y-junction nitrogen-doped carbon nanotubes and such nanotubes might be an effective material to fabricate various field emission devices.     

氮/硫共掺杂多孔碳纳米片的制备及其电化学性能

二维多孔碳材料能够提供较短的电解质扩散通道和较快的电子传输过程,因此在能量转换和储存装置中表现出优异的电化学性能.近年来的理论和实验研究表明,两元素共掺杂可使二维多孔碳材料的电化学性能得到明显提高.因此,共掺杂二维多孔碳材料的制备成为目前的研究热点之一.本文以甲基橙-FeCl₃复合物为模板引发剂制备了甲基橙掺杂的聚吡咯纳米管,通过对聚吡咯纳米管与KOH混合物（重量比为1：2）在700 ℃进行热处理,制备了二维石墨烯状氮/硫共掺杂多孔碳纳米片.所制备的氮/硫共掺杂多孔碳纳米片相互连结,形成了多级孔结构.氮气吸附分析表明多级孔结构包含微孔、介孔和大孔,这使所制备的氮/硫共掺杂多孔碳纳米片具有较高的比表面积（1744.58 m²/g）和孔体积（1.01 cm³/g）.共掺杂多孔碳纳米片中的掺杂氮以吡啶氮、吡咯氮和季胺氮形式存在,掺杂硫以噻吩硫和氧化态硫形式存在,二者之间的协同效应能够明显改善碳纳米片表面的浸润性,增加表面电化学活性点.这些特征使所制备的氮/硫共掺杂多孔碳纳米片表现出优异的电化学性能.用氮/硫共掺杂多孔碳纳米片制备的量子点敏化太阳能电池对电极,对多硫电解质再生反应的电催化活性与传统PbS对电极相近,所组装电池的光电转换效率可达到4.30%（100 mW/cm²）.氮/硫共掺杂多孔碳纳米片作为超级电容器电极材料,以6 M（1 M=1 mol/L）KOH为电解质,电流密度为0.4 A/g,比电容达到312.8 F/g.即使电流密度增加到20 A/g,比电容仍达到200.6 F/g,表明其具有较好的倍率性能.     

One-pot low temperature synthesis of MFe2O4 (M=Co,Ni, Zn) superparamagnetic nanocrystals

Magnetic MFe₂O₄ (M=Co, Ni, Zn) nanocrystals with a diameter about 30 nm and a nearly spherical shape were synthesized via a simple hydrothermal approach. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy have been used to investigate the as-prepared magnetic MFe₂O₄ (M=Co, Ni, Zn) nanocrystals. Magnetic properties of the as-prepared samples have been detected by a vibrating sample magnetometer at room temperature and the results show that the as-prepared magnetic MFe₂O₄ nanocrystals are a type characteristic of superparamagnetic materials. These superparamagnetic nanocrystals are believed to be promising for wide engineering applications, such as drug delivery, bioseparation, and magnetic resonance imaging.     

Synthesis of high nitrogen doping of carbon nanotubes and modeling the stabilization of filled DAATO@CNTs (10,10) for nanoenergetic materials

In this work, we have performed synthesis of nitrogen-doped carbon nanotubes using chemical vapor deposition method. Morphology, structure and composition of the carbon nanotubes (CNTs), as well as concentration and distribution of nitrogen inside CNTs are characterized by scanning electron microscopy, transmission electron microscopy, X-ray dispersive spectroscopy and X-ray photoelectron spectroscopy techniques. A bamboo-like structure of the nitrogen-doped CNTs has been observed. Temperature dependency on the synthesis of nitrogen-doped carbon nanotubes has been investigated and discussed. Diameter and growth rate of these hybrid materials are obviously temperature dependent. Nitrogen concentration inside the CNTs increases with declining synthesis temperature. Nitrogen-doped CNTs with nitrogen content up to 10.4 at% can be achieved at a low temperature of 800 ^oC. Synthesis of the high nitrogen CNTs proposes a feasible way to develop novel nanoenergetic materials. Besides the experimental study, we have carried out Density Functional Theory calculations on five energetic molecules named n-oxides of 3,3′-azo-bis(6-amino-1,2,4,5-tetrazine) (DAATO), where n=1-5 refer to oxygen atoms, encapsulated in CNTs (10,10), in order to investigate the chemical stabilization of filled DAATO_n inside CNTs (10,10). In fact, the predicted adsorption energy values confirmed the chemical stability of the hybrid systems DAATO_n@CNTs (10,10) under normal conditions.     

Iron phthalocyanine oligomer/Fe3O4 hybrid microspheres and their microwave absorption property

The novel nano-scale iron phthalocyanine oligomer/Fe₃O₄ (FePc/Fe₃O₄) hybrid microspheres were synthesized from iron phthalocyanine oligomer and FeCl₃·6H₂O via a solvent-thermal crystallization route. The morphology and structure of the hybrid microspheres were characterized by Fourier transform infrared spectrophotometer, X-ray diffraction, scanning electron microscopy and transmission electron microscopy. These results showed that the hybrids were monodisperse microspheres and the morphology can be adjusted by controlling pre-polymerization time. The saturation magnetization increased with increase in the pre-polymerization time, while the coercivities decreased. The FePc/Fe₃O₄ hybrid microspheres exhibited novel microwave electromagnetic properties: the dielectric loss was enhanced when the pre-polymerization time increased and a new microwave loss peak appeared at high frequency. The microwave absorbing properties enhanced with increase in the pre-polymerization time and a maximum reflection loss of −29.7 dB was obtained at 11.7 GHz with 6 h of pre-polymerization time when the matching thickness was 3.0 mm. The novel hybrid materials are believed to have potential applications as microwave absorbing materials.     

Synthesis of nanometer Bi2WO6 synthesized by sol-gel method and its visible-light photocatalytic activity for degradation of 4BS

Nanometer Bi₂WO₆ catalyst with visible-light responsive was prepared by a sol-gel method in the presence of EDTA. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV-vis diffuse reflectance spectrum, Fourier transform infrared (FTIR) spectrum, Brunauer-Emmet-Teller (BET). The UV-vis diffuse reflectance spectrum of the as-prepared sample shows a markedly blue-shift as compared to that of the sample obtained by a solid-state reaction. The as-prepared samples exhibited higher activities than that synthesized by the solid-state reaction for 4BS photodegradation under visible-light irradiation (λ>400 nm) and the sample prepared at 450 °C exhibited the highest photocatalytic activity.     

Alumina template-assisted electrodeposition of Bi2Te2.7Se0.3 nanowire arrays

Bi₂Te_2.7Se_0.3 nanowire arrays have been fabricated by electrodeposition into the pores of an anodic aluminum oxide (AAO) template followed by annealing at 300 °C under Ar atmosphere. The as-prepared nanowires were characterized by X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy and energy dispersive X-ray spectroscopy. The nanowires are uniform single crystalline with diameter of ∼14 nm.     

A facile strategy for covalent binding of nanoparticles onto carbon nanotubes

This paper describes a simple strategy for covalently attaching nanoparticles onto the carbon nanotubes (CNTs) to fabricate hybrid nanostructure. Densely distributed magnetite nanoparticles (MNPs) with a size of 8 nm have been deposited on the surface of carbon nanotubes by covalent interaction. Transmission electron microscopy (TEM), FT-IR spectroscopy, and X-ray diffraction (XRD) analysis have been used to study the formation of MNP/CNT nanostructure. The strategy employed herein is quite generic and applicable to a variety of nanoparticles, including metal, quantum dot and oxide. These composite nanostructures should open up new possibilities in areas such as nanoelectronics, chemical sensing, field-emission displays, nanotribology, and cell adhesion/biorecognition investigations.     

Standing or lying C70s encapsulated in carbon nanotubes with different diameters

Single-walled carbon nanotubes (SWNTs) encapsulating C₇₀s, so-called C₇₀ peapods, were synthesized in high yield by a vapor-phase doping method. Raman spectra, high resolution transmission electron microscopy (HRTEM), and selected area electron diffraction (SAED) measurement indicate that the tube diameter is one of the important factors to determine the orientation of C₇₀ molecules inside the SWNTs. SWNTs with different diameters give different alignment of C₇₀ molecules. The lying orientation is favorable over the standing orientation in thin nanotube, i.e. 1.36 nm nanotubes, whereas the standing orientation is favorable in thick nanotubes, i.e. 1.49 and 1.61 nm nanotubes.     

Synthesis and characterization of ZrO2/MnO2/carbon clusters nanocomposite materials

Nano-sized ZrO₂/MnO₂/carbon clusters composite materials has been successfully obtained by the calcination of a Zr(acac)₄/Mn(acac)₃/epoxy resin complex under an oxygen atmosphere. The compositions of the resulting composite materials were determined using inductively coupled plasma (ICP) spectroscopy, elemental analysis and surface characterization by X-ray diffraction (XRD), scanning electron microscopy and transmission electron microscopy (TEM). The ultraviolet–visible (UV–VIS), X-ray photoelectron spectra (XPS) and electron spin resonance (ESR) spectra of the composites were also measured. ESR spectral examinations suggest the possibility of an electron transfer in the process of MnO₂ → carbon clusters → ZrO₂. The visible light-responsive oxidation–reduction ability of the calcined material was also investigated.     

New aspects on pulsed laser deposition of aligned carbon nanotubes

We have grown carbon nanotubes (CNT) by pulsed laser deposition (PLD) at 1000 °C in Ar atmosphere. A Nd/YAG laser was used for irradiation of a graphite target containing Ni and Co rods. High-resolution scanning electron microscopy (HRSEM) and transmission electron microscopy (TEM) images showed that “closed” carbon nanotubes were grown between clusters of metallic particles, so that the individual nanotubes were arranged in parallel to each other forming a shape of “Rope-Bridge”. The nanotubes structure was analyzed by high-resolution transmission electron microscopy (HRTEM) and their type was found to be of MWNT, containing about five SWNT. Total diameter was 5-20 nm and their length was about 1 μm. High homogeneous distribution carbon nanotubes were grown and different structures were observed such as well-aligned carbon nanotubes, bamboo-like and Y-junction carbon nanotubes.