Synthesis and magnetic properties of hexagonal Y(Mn,Cu)O3 multiferroic materials

Single-phase hexagonal-type solid solutions based on the multiferroic YMnO₃ material were synthesized by a modified Pechini process. Copper doping at the B-site (YMn_1−xCu_xO₃; x<0.15) and self-doping at the A-site (Y_1+yMnO₃; y<0.10) successfully maintained the hexagonal structure. Self-doping was limited to y(Y)=2 at% and confirmed that excess yttrium avoids formation of ferromagnetic manganese oxide impurities but creates vacancies at the Mn site. Chemical substitution at the B-site inhibits the geometrical frustration of the Mn³⁺ two-dimensional lattice. The magnetic transition at T_N decreases from 70 K down to 49 K, when x(Cu) goes from 0 to 15 at%. Weak ferromagnetic Mn³⁺-Mn⁴⁺ interactions created by the substitution of Mn³⁺ by Cu²⁺, are visible through the coercive field and spontaneous magnetization but do not modify the overall magnetic frustration. Presence of Mn³⁺-Mn⁴⁺ pairs leads to an increase of the electrical conductivity due to thermally-activated small-polaron hopping mechanisms. Results show that local ferromagnetic interactions can coexist within the frustrated state in the hexagonal polar structure.     

Ferromagnetism in epitaxial orthorhombic YMnO3 thin films

Epitaxial orthorhombic YMnO₃ thin films, (0 0 1) oriented, have been grown by pulsed laser deposition on (0 0 1)SrTiO₃ substrates. Their crystal structure and magnetic response have been studied in detail. Although bulk o-YMnO₃ is antiferromagnetic, our magnetic measurements reveal intriguing thermal hysteresis between the zero-field-cooled and field-cooled curves below the onset of the antiferromagnetic ordering temperature, thus signaling a more complex magnetic structure with net ferromagnetic moments. We discuss on the possible origin of this net magnetization and we have found a correlation of the magnetic response with the strain state of the films. We propose that substrate-induced strain modifies the subtle competition of magnetic interactions and leads to a non-collinear magnetic state that can thus be tuned by strain engineering.     

The electrical and magnetic properties of epitaxial orthorhombic YMnO3 thin films grown under various oxygen pressures

Orthorhombic YMnO₃ thin films were epitaxially grown on bare and LaNiO₃ buffered (0 0 1)-SrTiO₃ substrates by pulsed laser deposition under various oxygen pressures from 5 to 30 Pa. The crystal structure and microstructure of these films have been characterized by both X-ray diffractions and transmission electron microscopy. The leakage current, modeled as the space charge limited current (SCLC) mechanism, decreased significantly with the increase of oxygen content. It is further found that the magnetic property of films is greatly enhanced in YMnO₃ films grown under high oxygen pressure, which can be explained decreased oxygen vacancies. In addition, bipolar switching behavior was obtained only in the films grown under 30 Pa oxygen pressure, which is attributed to the decrease of voltage-driven oxygen vacancy migration.     

The multiferroic properties of Bi(Fe0.95Co0.05)O3 films

Bi(Fe_0.95Co_0.05)O₃ films were prepared on conductive indium tin oxide (ITO)/glass substrates by chemical solution deposition. Well saturated polarization hysteresis loop has been observed with a remnant polarization value of about 22 μC/cm² at room temperature. Weak ferromagnetism with saturation magnetization of about 3 emu/cm³ was observed at room temperature. The clear observation of both room temperature ferroelectric and ferromagnetic properties suggests the potential multiferroic applications of Bi(Fe_0.95Co_0.05)O₃.     

Luminescence spectrum from hexagonal YMnO3

Luminescence spectrum and its temperature dependence have been investigated for hexagonal YMnO₃ crystal which is ferroelectric below T_C=914 K and becomes simultaneously antiferromagnetic below T_N=74 K. The luminescence spectrum is as broad as two-magnon Raman scattering spectrum. The luminescence intensity is comparable to the latter at room temperature and it increases rapidly as the temperature decreases. These characteristics are discussed based upon other optical responses and theoretical results.     

Effect of La doping in the multiferroic compound BiFeO3

We have performed magnetization and magnetocapacitance measurements on ceramic samples of the multiferroic series Bi_1−xLa_xFeO₃ for 0≤x≤.0.25. We show that doping with La reduces the transition magnetic field from the spatially modulated state to a homogenous one and increases the magnetocapacitance, these effects being the strongest for x=0.15, which is the highest concentration for maintaining the non-centrosymmetric rhomboedral structure (R3c) of BiFeO₃. For highest La content (x≥0.17), analysis of the XRD patterns shows that the lattice symmetry gradually changes to orthorhombic (C222), giving rise to an enhancement of the latent magnetization and to a drop of the magnetodielectric constant.     

Microstructures and multiferroic properties of textured Bi0.8La0.2FeO3 thin films

La-substituted BiFeO₃, Bi_0.8La_0.2FeO₃, thin films were fabricated on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition. X-ray diffraction and high-resolution transmission electron microscope were used to analyze the structures of the films. The results show the films fabricated under optimized growth condition are (0 1 2) textured. X-ray photoemission spectroscopy results indicate that the oxidation state of Fe ion is Fe³⁺ in the films without detectable Fe²⁺. The films show low leakage current and excellent dielectric characters. Multiferroic properties with a remnant ferroelectric polarization of 5.2 μC/cm² and a remanent magnetization of 0.02 μ_B/Fe were established. These results have some implications for further research.     

Effect of magnetic annealing on magnetization of BiFeO3 ceramics

The effect of magnetic annealing treatment on the magnetization of multiferroic BiFeO₃ was studied systematically. A series of pelletized nano-sized BiFeO₃ powders were annealed at high temperature under different magnetic fields. Typical ferromagnetic hysteresis loops were obtained at room temperature of the ceramics which were derived from ferromagnetic BiFeO₃ precursors. On the other hand, antiferromagnetic behaviors were observed in other samples synthesized from nonmagnetic precursors. The enhanced magnetic properties were ascribed to the magnetic anisotropy which was induced by the strong magnetic fields. This work indicates that the strong magnetic annealing method is an alternative approach to tuning the magnetic properties of high performance multiferroic materials with canted antiferromagnetic ordering.     

Soft-mode driven tetragonal-to-monoclinic phase transition in multiferroic BiFeO3

The phase transition of BiFeO₃ (BFO) from tetragonal to monoclinic induced by pressure was investigated by first-principles method. The sequential monoclinic phase, _Ma$M_{\mathrm{a}}$, which is favorable during low compression with respect to the tetragonal phase, was characterized. The order parameters were calculated in the vicinity of the phase transition, showing that phase transition has a second-order character. The results demonstrated that the pressure-induced tetragonal-to-monoclinic phase transition in BFO is related to the softening behavior of the E mode, which are very helpful in further investigations of the morphotropic phase boundary (MPB) in lead-free materials.     

锰酸钇薄膜中Mn3+离子d-d跃迁的超快光谱学研究

本文利用时间分辨光谱技术,系统研究了飞秒激光诱导YMnO₃薄膜中Mn³⁺离子3d轨道跃迁的 载流子动力学过程.当抽运光子能量为1.7 eV,对应于Mn³⁺离子的3d轨道跃迁, 抽运-探测零延迟时间处的透射率变化随着温度的降低逐渐减小. 这起源于低温下短程反铁磁有序诱导Mn³⁺离子d-d能级发生"蓝移". 载流子弛豫过程由快、慢两个过程组成,分别对应于电子-声子相互作用和自旋-声子相互作用. 实验发现,当温度低于80 K,电子-声子热化时间显著增加,表明低温下电子-声子的 耦合强度受长程反铁磁有序的影响.     

Effects of doping site and pre-sintering time on microstructure and magnetic properties of Fe-doped BaTiO3 ceramics

The A-site substituted BaTiO₃ ceramics were prepared by solid-state reaction via partial substitution of Fe for Ba²⁺. By comparison with the B-site substituted sample made under similar conditions, the effect of Fe doping site on microstructure and magnetism was investigated using X-ray diffraction, Mössbauer spectroscopy and vibrating sample magnetometer. It is found that A-site substitution can be realized to a certain extent at 7 at% Fe addition, whereas impurities are observed at higher Fe concentrations. In the nominal (Ba_0.93Fe_0.07)TiO₃ sample, the Fe ions are present as Fe²⁺ and Fe³⁺, respectively, replacing A-site Ba²⁺ and octahedral B-site Ti⁴⁺ in hexagonal perovskite lattice. The double-exchange Fe²⁺-O²⁻-Fe³⁺ interactions produce ferromagnetism well above room temperature, but the saturation magnetization and the Curie temperature are both obviously lower than those for B-site substitution due to different magnetic exchange mechanisms. In the B-site substituted sample Ba(Ti_0.93Fe_0.07)O₃, the super-exchange interactions between Fe³⁺ on pentahedral and octahedral Ti⁴⁺ sites are responsible for ferromagnetism. These results mean that B-site substitution is a better way for Fe-doped BaTiO₃ system to obtain high-Curie-temperature ferromagnetism. Moreover, increasing pre-sintering time can further improve the magnetism of B-site substituted samples, through which the saturation magnetization for Ba(Ti_0.93Fe_0.07)O₃ is enhanced ∼6 times.     

Effect of Cr substitution on the multiferroic properties of BiFe1 − xCrxO3 compounds

Single-phase BiFe_1 − xCr_xO₃ (x=0, 0.05 and 0.1) compounds are synthesized by a sol-gel process. The lattice parameters decrease and the magnetizations increase with the Cr content. Moreover, the magnetoelectric coupling between magnetic order and ferroelectric order at room temperature was enhanced.     

Magnetic properties of Ni-substituted BiFeO3

BiFe_1−xNi_xO₃ ceramic powders with x up to 0.10 have been prepared by the sol-gel technique. The band gap of BiFeO₃ is 2.23 eV, and decreases to 2.09 eV for BiFe_0.95Ni_0.05O₃ and BiFe_0.90Ni_0.10O₃. The Mössbauer spectra show sextet at room temperature, indicating the magnetic ordering and the presence of only Fe³⁺ ions. Superparamagnetism with blocking temperature of 31 K for BiFe_0.95Ni_0.05O₃ and 100 K for BiFe_0.90Ni_0.10O₃ was observed. Enhanced magnetization at room temperature have been observed (1.0 emu/g for BiFe_0.95Ni_0.05O₃ and 2.9 emu/g for BiFe_0.90Ni_0.10O₃ under magnetic field of 10,000 Oe), which is one order larger than that of BiFeO₃ (0.1 emu/g under magnetic field of 10,000 Oe). The enhanced magnetization was attributed to the suppression of the cycloidal spin structure by Ni³⁺ substitution and the ferrimagnetic interaction between Fe³⁺ and Ni³⁺ ions.     

Effect of Mn doping on structural and magnetic properties of GaFeO3

GaFe_1−xMn_xO₃ polycrystalline materials have been prepared by a solid state reaction (SR) and by the sol-gel (SG) method. The maximum Mn content amounts up to 10% and 40% for SR and SG preparation, respectively. All compounds in these composition ranges crystallize in space group P c 2₁ n derived from Rietveld refinement of X-ray powder patterns. The gradual incorporation of manganese is accompanied by a decrease in the cell volume. The ferrimagnetic transition temperature of T_c=282 K for GaFeO₃ decreases with Mn content and reaches T_c=149 K for x=0.4.     

Effect of Sr concentration on microstructure and magnetic properties of (Ba1−xSrx)(Ti0.3Fe0.7)O3 ceramics

Fe-doped (Ba_1−xSr_x)TiO₃ ceramics were prepared by solid-state reaction, and ferromagnetism was realized at room temperature. The microstructure and magnetism were modified by the Sr concentration control (0≤x≤75 at%) at a fixed Fe concentration, and the relevant magnetic exchange mechanism was discussed. All the samples are shown to have a single perovskite structure. When increasing the Sr concentration, the phase structure is transformed from a hexagonal perovskite into a cubic perovskite, with a monotonic decrease in lattice parameters induced by ionic size effect. The room-temperature ferromagnetism is expected to originate from the super-exchange interactions between Fe³⁺ on pentahedral and octahedral Ti sites mediated by the O²⁻ ions. The increase in Sr addition modifies two main influencing factors in magnetic properties: the ratio of pentahedral to octahedral Fe³⁺ and the concentration of oxygen vacancies, leading to a gradually enhanced saturation magnetization. The highest value, obtained for Fe-doped (Ba_0.25Sr_0.75)TiO₃, is an order of magnitude higher than that of the Fe-doped BaTiO₃ system with similar Fe concentration and preparation conditions, which may indicate (Ba_1−xSr_x)TiO₃ as a more suitable matrix material for multiferroic research.     

Effect of WO3 on structural and optical properties of CeO2-PbO-B2O3 glasses

Pure and WO₃ doped CeO₂-PbO-B₂O₃ glasses are prepared by the melt-quench technique. The structural and optical analyses of glasses are carried out by XRD, FTIR, density and UV-vis spectroscopic measurement techniques. FTIR analysis indicates the transformation of structural units of BO₃ into BO₄ with W-O-W vibration and the presence of WO₄ and WO₆ units observed with increase in WO₃ contents. Decrease in band gap for CeO₂-PbO-B₂O₃ glasses from 2.89 to 2.30 eV and for WO₃ doped glasses from 2.89 to 1.95 eV has been observed and discussed. This decrease in band gap with WO₃ doping approaches to semiconductor behavior. It shows that the presence of WO₃ in the glass samples causes more compaction of the borate network due to the formation of BO₄ groups and the presence of WO₄ and WO₆ groups, which result in a decrease in the optical band gap energy and increase in the density.     

α-Fe2O3-In2O3 mixed oxide nanoparticles synthesized under hydrothermal supercritical conditions

α-Fe₂O₃-In₂O₃ mixed oxide nanoparticles system has been synthesized by hydrothermal supercritical and postannealing route, starting with (1−x)Fe(NO₃)₃·9H₂O·xIn(NO₃)₃·5H₂O aqueous solution (x=0-1). X-ray diffraction and Mössbauer spectroscopy have been used to study the phase structure and substitutions in the nanosized samples. The concentration regions for the existence of the solid solutions in the α-Fe₂O₃-In₂O₃ nanoparticle system together with the solubility limits of In³⁺ ions in the hematite lattice and of Fe³⁺ ions in the cubic In₂O₃ structure have been evidenced. In general, the substitution level is considerably lower than the nominal concentration x. A justification of the processes leading to the formation of iron and indium phases in the investigated supercritical hydrothermal system has been given.     

Electrical behavior of high resistivity Ce-doped BiFeO3 multiferroic

Bi_1+xCe_xFeO₃ (Ce–BFO) for x=0, 0.05, 0.1, and 0.15 monophasic ceramic samples were successfully synthesized by conventional solid-state reaction routes. The influences of Ce doping on structural, dielectric, ferroelectric, leakage current and capacitive properties of BiFeO₃ ceramics were investigated intensively. At higher concentrations of x (x=0.1 and 0.15) the samples showed good crystallinity with almost impurity free phases. No structural phase transformation took place after partial doping of Ce ions and all ceramic bulk samples remain in their rhombohedral structure with space group R3c. The dielectric behavior of the samples improved significantly and the ferroelectric hysteresis loops changed their shape from rounded to a strongly nonlinear typical ferroelectric feature mainly originating from the domain switching and became enhanced with increase in doping concentration of cerium (Ce). Experimental results also suggested that partial doping of higher valence, smaller ionic radius Ce ions in BiFeO₃ forces the reduction of oxygen vacancies, resulting in a great suppression of leakage current. It is found that the sharp capacitance peak/discontinuity present in the C–V characteristics of Ce–BFO for different Ce doping concentrations is directly associated with the polarization reversal. Incorporation of excess bismuth in the presence of Ce in BiFeO₃ is expected to compensate Bi loss during high temperature sintering and caused structural distortion which also favors enhancement of ferroelectric properties in Ce-doped BFO.     

Magnetic and electrical properties of bulk BaTiO3+MgFe2O4 composite

BaTiO₃+MgFe₂O₄ material system was synthesized by hybrid chemical process using chlorides and nitrates of barium, titanium, iron, and magnesium. Magnetic properties of the composite samples measured as a function of annealing conditions indicated soft magnetic behavior. Saturation specific magnetization from 8 21 emu/g was observed for samples annealed at temperature between 950 and 1150 °C. Variation of specific saturation magnetization with respect to annealing temperature was related with the distribution of Fe cations in the tetrahedral and octahedral sites of MgFe₂O₄. Electrical properties of the samples annealed at different temperatures were measured to analyze the coexistence of ferroelectric phase. Dielectric constant varying from 15 to 200 with respect to frequency was observed for samples annealed from 950 to 1150 °C.