Effect of pH value on the structural and magnetic properties of nanocrystalline strontium hexaferrite thin films

Strontium hexaferrite SrFe₁₂O₁₉ thin films have been synthesized at different pH, adjusted by NH₄OH, on the Si (1 0 0) substrate using a spin coating sol-gel process. Fourier transform infrared spectroscopy analysis and theoretical calculations were conducted for determination and controlling metal citrates in solution precursors. X-ray diffraction, scanning electron microscopy and vibrating sample magnetometer were applied to evaluate the composition, microstructure, crystallite size and magnetic properties of the SrFe₁₂O₁₉ thin films. Using the solution with pH 7, the approximately single phase strontium hexaferrite thin films with optimum physical properties can be obtained at calcination temperature of 800 °C. The SrFe₁₂O₁₉ thin films derived from the solution with pH 7 after calcination at 800 °C exhibited crystallite size of 42 nm and magnetic properties of M_s=267 emu/cm³ (at 10 kOe), M_r=134 emu/cm³ and H_c=4290 Oe.     

Preparation of strontium hexaferrite film by pulsed laser deposition with in situ heating and post annealing

Strontium hexaferrite (SrFe₁₂O₁₉) films have been fabricated by pulsed laser deposition on Si(1 0 0) substrate with Pt(1 1 1) underlayer through in situ and post annealing heat treatments. C-axis perpendicular oriented SrFe₁₂O₁₉ films have been confirmed by X-ray diffraction patterns for both of the in situ heated and post annealed films. The cluster-like single domain structures are recognized by magnetic force microscopy. Higher coercivity in perpendicular direction than that for the in-plane direction shows that the films have perpendicular magnetic anisotropy. High perpendicular coercivity, around 3.8 kOe, has been achieved after post annealing at 500 °C. Higher coercivity of the post annealed SrFe₁₂O₁₉ films was found to be related to nanosized grain of about 50–80 nm.     

Synthesis and characterization of nanostructured strontium hexaferrite thin films by the sol–gel method

Nanostructured single phase strontium hexaferrite, SrFe₁₂O₁₉, thin films have been synthesized on the (100) silicon substrate using a spin coating sol–gel process. The thin films with various Fe/Sr molar ratios of 8–12 were calcined at different temperatures from 500 to 900 °C. The composition, microstructure and magnetic properties of the SrFe₁₂O₁₉ thin films were characterized using Fourier transform infrared spectroscopy, differential thermal analysis, thermogravimetry, X-ray diffraction, electron microscopy and vibrating sample magnetometer. The results showed that the optimum molar ratio for Fe/Sr was 10 at which the lowest calcination temperature to obtain the single phase strontium hexaferrite thin film was 800 °C. The magnetic measurements revealed that the sample with Fe/Sr molar ratio of 10, exhibited higher saturation magnetization (267.5 emu/cm³) and coercivity (4290 Oe) in comparison with those synthesized under other Fe/Sr molar ratios.     

Microwave-assisted synthesis of SrFe12O19 hexaferrites

Ultra-fine and homogeneous SrFe₁₂O₁₉ hexaferrites were synthesized by a microwave-assisted calcination route. The calcined precursors were prepared by a sol-gel auto-combustion method using Fe(NO₃)₃·9H₂O, Sr(NO₃)₂ and citric acid as starting materials. The structures, powder morphology and magnetic properties of the products were characterized by X-ray diffraction, scanning electron microscope and vibrating sample magnetometer. The results showed that microwaves are helpful to reduce the calcination temperature and shorten the calcination time. The ferrites with saturation magnetization, remanence and intrinsic coercivity of 54.80 emu/g, 29.52 emu/g and 5261 Oe, respectively, were obtained in samples calcined at 800 °C for 80 min.     

Effect of annealing temperature on the structural, photoluminescence and magnetic properties of sol-gel derived Magnetoplumbite-type (M-type) hexagonal strontium ferrite

Magnetoplumbite-type (M-type) hexagonal strontium ferrite particles were synthesized via sol-gel technique employing ethylene glycol as the gel precursor at two different calcination temperatures (800 and 1000 °C). Structural properties were systematically investigated via X-ray diffraction (XRD), field emission scanning electron microscopy, high resolution transmission electron microscopy (HRTEM), energy dispersive spectroscopy (EDS), thermogravimetric analysis (TGA), photoluminescence spectrophotometry and superconducting quantum interference device magnetometer. XRD results showed that the sample synthesized at 1000 °C was of single-phase with a space group of P6₃/mmc and lattice cell parameter values of a=5.882 Å and c=23.048 Å. EDS confirmed the composition of strontium ferrite calcined at 1000 °C being mainly of M-type SrFe₁₂O₁₉ with HRTEM micrographs confirming the ferrites exhibiting M-type long range ordering along the c-axis of the crystal structure. The photoluminescence (PL) property of strontium ferrite was examined at excitation wavelengths of 260 and 270 nm with significant PL emission peaks centered at 350 nm being detected. Strontium ferrite annealed at higher temperature (1000 °C) was found to have grown into larger particle size, having higher content of oxygen vacancies and exhibited 83-85% more intense PL. Both the as-prepared strontium ferrites exhibited significant oxygen vacancies defect structures, which were verified via TGA. Higher calcination temperature turned strontium ferrite into a softer ferrite.     

Magnetic properties of substituted strontium ferrite nanoparticles and thin films

SrFe_12−x(Zr_0.5Mg_0.5)_xO₁₉ nanoparticles and thin films with x=0-2.5 were synthesized by a sol-gel method on thermally oxidized silicon wafer (Si/SiO₂). Structural and magnetic characteristics of synthesized samples were studied employing x-rays diffraction (XRD), transmission electron microscopy (TEM), magnetic susceptometer, atomic force microscopy (AFM), field emission scanning electron microscopy (FE-SEM), and vibrating sample magnetometer (VSM). TEM micrographs display that the narrow size distribution of ferrite nanoparticles with average particle size of 50 nm were fabricated. Fitting obtained data of effective magnetic susceptibility by Vogel-Fulcher law confirms the existence of strong magnetic interaction among fine particles. XRD patterns and FE-SEM micrographs demonstrated that single phase c-axis hexagonal ferrite films with rather narrow grain size distribution were obtained. AFM micrographs exhibited that the surface roughness increases with an increase in Zr-Mg content. It was found from the VSM graphs that with an increase in substitution contents the coercivity decreases, while the saturation of magnetization increases. The Henkle plots confirms the existence of exchange coupling among nano-grain in ferrite thin films.     

Preparation and characterization of Co–Pt bimetallic magnetic nanoparticles

CoPt₃ nanoparticles are synthesized by a two-stage route using NaBH₄ as a reductant. The nanoparticles are characterized by thermogravimetry (TG) and differential thermal analysis (DTA), Fourier transform infrared (FT-IR), transmission electron microscopy (TEM) and X-ray diffraction (XRD). Structural and spectroscopic studies show that the nanoparticles adopt a face-centered-cubic (FCC) crystalline structure with an average particle size of 2.6 nm. SQUID studies reveal that as-synthesized nanoparticles are superparamagnetic at room temperature and ferromagnetic at 1.85 K with coercivity of 980 Oe. Annealing of the samples at 500 °C causes an increase of particle size and a decrease of coercivity.     

Effect of Fe/Sr mole ratios on the formation and magnetic properties of SrFe12O19 microtubules prepared by sol-gel method

The sol was obtained by sol-gel method. Then, the sol was dripped onto the absorbent cotton template. The gel was obtained after the evaporation of water. Strontium ferrite microtubules were prepared after carrying out calcination process at different temperatures. The phase, morphology and particle diameter and the magnetic properties of samples were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM), respectively. The effects of Fe³⁺/Sr²⁺ mole ratio and calcination temperature on the crystal structure, morphology and magnetic properties of ferrite microtubules were studied. The external diameters of obtained SrFe₁₂O₁₉ microtubules were found to range between 8 and 13 μm; the wall thicknesses ranged between 1 and 2 μm. When the Fe³⁺/Sr²⁺ mole ratio and the calcination temperature were 11.5 and 850 °C, respectively, the coercivity, saturation magnetization and remanent magnetization for the samples were 7115.1 Oe, 70.1 and 42.4 emu/g, respectively. The mechanism of the formation and variation in magnetic properties of the microtubules were explained.     

Microwave absorption properties of 50% SrFe12O19–50% TiO2 nanocomposites with porosity

SrFe₁₂O₁₉–TiO₂ nanocomposites are usually used for absorbing microwaves in military and civil applications. In this work, microwave absorption properties of porous SrFe₁₂O₁₉ nanocomposites with 50% weight ratio of TiO₂ have been investigated. 50% TiO₂–50% SrFe₁₂O₁₉ nanocomposites were prepared by a controlled hydrolysis of titanium tetraisopropoxide in which SrFe₁₂O₁₉ nanoparticles were synthesized by a sol–gel auto combustion route. The morphology, crystalline structure and crystallite size of SrFe₁₂O₁₉–TiO₂ nanocomposites were characterized by field emission scanning electron microscopy and X-ray powder diffraction. The magnetic measurements were carried out with a vibrating sample magnetometer. The microwave absorption was measured by a Vector Network Analyzer. The microwave absorption results indicated that the reflection losses for specimens with 52%–56% porosity and thicknesses of 1.8, 2.1 and 2.6 mm were not very low but minimum reflection loss for a specimen with 4.2 mm thickness reached upto −33 dB.     

Structural characterization and magnetic properties of superparamagnetic zinc ferrite nanoparticles synthesized by the coprecipitation method

Single phase zinc ferrite (ZnFe₂O₄) nanoparticles have been prepared by the coprecipitation method without any subsequent calcination. The effects of precipitation temperature in the range 20–80 °C on the structural and the magnetic properties of zinc ferrite nanoparticles were investigated. The crystallite size, microstructure and magnetic properties of the prepared nanoparticles were studied using X-ray diffraction (XRD), Fourier transmission infrared spectrum, transmission electron microscope (TEM), energy dispersive X-ray spectrometer and vibrating sample magnetometer. The XRD results showed that the coprecipitated nanoparticles were single phase zinc ferrite with mixture of normal and inverse spinel structures. Furthermore, ZnFe₂O₄ nanoparticles have the crystallite size in the range 5–10 nm, as confirmed by TEM. The magnetic measurements exhibited that the zinc ferrite nanoparticles synthesized at 40 °C were superparamagnetic with the maximum magnetization of 7.3 emu/g at 10 kOe.     

Structural and magnetic properties of SrFe12O19 hexaferrite synthesized by a modified chemical co-precipitation method

M-type strontium hexaferrite (SrFe₁₂O₁₉) particles had been prepared by a modified chemical co-precipitation route. Structural and magnetic properties were systematically investigated. Rietveld refinement of X-ray powder diffraction results showed that the sample was single-phase with the space group of P6₃/mmc and cell parameter values of a=5.8751 Å and c=23.0395 Å. The results of field-emission scanning electronic microscopy showed that the grains were regular hexagonal platelets with sizes from 2 to 4 μm. The composition determined by energy dispersive spectroscopy is the stoichiometry of SrFe₁₂O₁₉. The ferrimagnetic to paramagnetic transition was sharp with Curie temperature T_C=737 K, which further confirmed that the samples were single phase. However, it was found that the coercivity, saturation magnetization and the squareness ratio of the synthesized SrFe₁₂O₁₉ samples were lower than the theoretical values, which could be explained by the multi-domain structure and the increase of the demagnetizing factor.     

Evidence of existence of metastable SrFe12O19 nanoparticles

The existence of metastable hexaferrite is reported. Synthesis of strontium hexaferrite, SrFe₁₂O₁₉, at 400 °C was realized under controlled oxygen atmosphere. Such technique allows obtaining of SrFe₁₂O₁₉ at lower temperatures than those by traditional methods (above 800 °C). Phase transformation occurred during a measurement of magnetization vs. temperature (heating up to 625 °C). The heat treatment induces a change from SrFe₁₂O₁₉ to γ-Fe₂O₃ (as the main phase), and SrFeO_2.74 to Sr₂Fe₂O₅. Together with these phase transformations, an increment in the amount of SrCO₃ is detected. Magnetic study of the samples, before and after the heating, supports the structural analysis conclusions.     

Synthesis and magnetic characterization of nickel ferrite nanoparticles prepared by co-precipitation route

Magnetic nanoparticles of nickel ferrite (NiFe₂O₄) have been synthesized by co-precipitation route using stable ferric and nickel salts with sodium hydroxide as the precipitating agent and oleic acid as the surfactant. X-ray diffraction (XRD) and transmission electron microscope (TEM) analyses confirmed the formation of single-phase nickel ferrite nanoparticles in the range 8-28 nm depending upon the annealing temperature of the samples during the synthesis. The size of the particles (d) was observed to be increasing linearly with annealing temperature of the sample while the coercivity with particle size goes through a maximum, peaking at ∼11 nm and then decreases for larger particles. Typical blocking effects were observed below ∼225 K for all the prepared samples. The superparamagnetic blocking temperature (T_B) was found to be increasing with increasing particle size that has been attributed to the increased effective anisotropy energy of the nanoparticles. The saturation moment of all the samples was found much below the bulk value of nickel ferrite that has been attributed to the disordered surface spins or dead/inert layer in these nanoparticles.     

Particle size effect on phase and magnetic properties of polymer-coated magnetic nanoparticles

Polymer-coated magnetic nanoparticles are hi-tech materials with ample applications in the field of biomedicine for the treatment of cancer and targeted drug delivery. In this study, magnetic nanoparticles were synthesized by chemical reduction of FeCl₂ solution with sodium borohydride and coated with amine-terminated polyethylene glycol (aPEG). By varying the concentration of the reactants, the particle size and the crystallinity of the particles were varied. The particle size was found to increase from 6 to 20 nm and the structure becomes amorphous-like with increase in the molar concentration of the reactant. The magnetization at 1 T field (M_1T) for all samples is > 45 emu/g while the coercivity is in the range of 100-350 Oe. When the ethanol-suspended particles are subjected to an alternating magnetic field of 4 Oe at 500 kHz, the temperature is increased to a maximum normalized temperature (3.8 °C/mg) with decreasing particle size.     

Magnetic properties of strontium hexaferrite films prepared by pulsed laser deposition

The magnetic properties of strontium hexaferrite (SrFe₁₂O₁₉) films fabricated by pulsed laser deposition on the Si(100) substrate with Pt(111) underlayer have been studied as a function of film thickness (50–700 nm). X-ray diffraction patterns confirm that the films have c-axis perpendicular orientation. The coercivities in perpendicular direction are higher than those for in-plane direction which indicates the films have perpendicular magnetic anisotropy. The coercivity was found to decrease with increasing of thickness, due to the increasing of the grain size and relaxation in lattice strain. The 200 nm thick film exhibits hexagonal shape grains of 150 nm and optimum magnetic properties of M_s=298 emu/cm³ and H_c=2540 Oe.     

Magnetic and rheological properties of monodisperse Fe3O4 nanoparticle/organic hybrid

Fe₃O₄ nanoparticle/organic hybrids were synthesized via hydrolysis using iron (III) acetylacetonate at ∼80 °C. The synthesis of Fe₃O₄ was confirmed by X-ray diffraction, selected-area diffraction, and X-ray photoelectron spectroscopy. Fe₃O₄ nanoparticles in the organic matrix had diameters ranging from 7 to 13 nm depending on the conditions of hydrolysis. The saturation magnetization of the hybrid increased with an increase in the particle size. When the hybrid contained Fe₃O₄ particles with a size of less than 10 nm, it exhibited superparamagnetic behavior. The blocking temperature of the hybrid containing Fe₃O₄ particles with a size of 7.3 nm was 200 K, and it increased to 310 K as the particle size increased to 9.1 nm. A hybrid containing Fe₃O₄ particles of size greater than 10 nm was ferrimagnetic, and underwent Verwey transition at 130 K. Under a magnetic field, a suspension of the hybrid in silicone oil revealed the magnetorheological effect. The yield stress of the fluid was dependent on the saturation magnetization of Fe₃O₄ nanoparticles in the hybrid, the strength of the magnetic field, and the amount of the hybrid.     

Synthesis of magnetite nanoparticles via a solvent-free thermal decomposition route

Superparamagnetic nanoparticles have been widely applied in various bio-medical applications. To date, it is still a challenge to synthesize nanosized Fe₃O₄ particles with controlled size and distribution. In this paper, a novel solvent-free thermal decomposition method is reported for synthesizing Fe₃O₄ nanoparticles. Size and morphology of the nanoparticles are determined by TEM while the structure of the nanoparticles is identified by FTIR, XPS and TGA measurements. Magnetic properties of the obtained particles are determined using VSM and SQUID measurement. The particle size of the Fe₃O₄ can be tailored by adjusting either reaction temperature or time. When the reaction temperature is increased to 330 °C and the reaction time is extended to 4 h, the average particle size of the obtained nanoparticles is ∼9 nm, while Ms value reaches ∼76 emu/g. The as synthesized Fe₃O₄ nanoparticles show well-established superparamagnetic properties with the blocking temperature at around 100 K.     

Synthesis and characterization of magnetic diphase ZnFe(2)O(4) /γ-Fe(2)O(3) electrospun fibers

Magnetic nanofibers of ZnFe₂O₄/γ-Fe₂O₃ composite were synthesized by electrospinning from a sol-gel solution containing a molar ratio (Fe/Zn) of 3. The effects of the calcination temperature on phase composition, particle size and magnetic properties have been investigated. Zinc ferrite fibers were obtained by calcinating the electrospun fibers in air from 300 to 800 °C and characterized by thermogravimetric analyses, Fourier transformed infrared spectroscopy, X-ray photoemission spectroscopy, X-ray diffraction, vibration sample magnetometry and magnetic force microscopy. The resulting fibers, with diameters ranging from 90 to 150 nm, were ferrimagnetic with high saturation magnetization as compared to bulk. An increase in the calcination temperature resulted in an increase in particle size and saturation magnetization. The observed increase in saturation magnetization was most likely due to the formation and growth of ZnFe₂O₄/γ-Fe₂O₃ diphase crystals. The highest saturation magnetization (45 emu/g) was obtained for fibers calcined at 800 °C.     

Magnetic properties of prussian blue modified Fe3O4 nanocubes

Size controlled cubic Fe₃O₄ nanoparticles in the size range 90–10 nm were synthesized by varying the ferric ion concentration using the oxidation method. A bimodal size distribution was found without ferric ion concentration and the monodispersity increased with higher concentration. The saturation magnetization decreased from 90 to 62 emu/g when the particle size is reduced to 10 nm. The Fe₃O₄ nanoparticles with average particle sizes 10 and 90 nm were surface modified with prussian blue. The attachment of prussian blue with Fe₃O₄ was found to depend on the concentration of HCl and the particle size. The saturation magnetization of prussian blue modified Fe₃O₄ varied from 10 to 80 emu/g depending on the particle size. The increased tendency for the attachment of prussian blue with smaller particle size was explained based on the surface charge. The prussian blue modified magnetite nanoparticles could be used as a radiotoxin remover in detoxification applications.     

Synthesis and magnetic properties of hard/soft SrFe12O19/Ni0.7Zn0.3Fe2O4 nanocomposite magnets

Magnetic nanocomposite SrFe₁₂O₁₉/Ni_0.7Zn_0.3Fe₂O₄ powders with different weight fractions of the Ni_0.7Zn_0.3Fe₂O₄ soft ferrite were synthesized by a combination of the sol–gel self-propagation and glyoxilate precursor methods. The results of magnetic measurements revealed the higher Mr/Ms ratio for the nanocomposites than that for the single phase SrFe₁₂O₁₉ which proves the existence of the intergrain exchange coupling between hard and soft magnetic phases with the exchange spring behavior. The highest Mr/Ms ratio of 0.63 was obtained in the composite consisting of 80 wt% of SrFe₁₂O₁₉ and 20 wt% Ni_0.7Zn_0.3Fe₂O₄. The microstructural studies of this sample exhibited the average dimensions of hard and soft phases about 20 nm and 15 nm, respectively which are small enough for strong exchange coupling according to the theoretical studies. The variations of the reduced remanence (Mr/Ms) with increasing the weight fraction of the soft phase could be also explained by the role of the exchange and dipolar interactions in tuning the magnetic properties of the nanocomposites.