Structure and magnetic properties of Co-substituted NiZn ferrite thin films synthesized by the sol-gel process

Co-substituted NiZn ferrite thin films, Ni_0.5Zn_0.5Co_xFe_2−xO₄ (0≤x≤0.2), were synthesized by the sol-gel process. The structure and magnetic properties of Ni_0.5Zn_0.5Co_xFe_2−xO₄ ferrite thin films have been investigated. The diffraction peak shifted towards the lower angle and the lattice parameter increased with Co substitution. There is little influence of Co substitution on the microstructure of NiZn ferrite thin films. The saturation magnetization gradually increases with the increase in Co substitution when x≤0.10, and decreases when x>0.10. Meanwhile, the coercivity initially decreases with the increase in Co substitution when x≤0.10, and increases when x>0.10.     

Preparation, and magnetic and electromagnetic properties of La-doped strontium ferrite films

SrLa_xFe_12−xO₁₉ films (x=0-1.0) with large magneto-crystalline anisotropy were synthesized on SiO₂ substrate by sol-gel and self-propagating high-temperature synthesis technique. The films were characterized by various experimental techniques including X-ray diffraction analysis, Field Emission Scanning Electron Microscope, Atomic Force Microscopy, Vibrating Sample Magnetometry and vector network analyzer. The results show that La ions completely enter into strontium ferrite lattice without changing the ferrite appearance; its grain size is approximately 40-80 nm, its length is 100 nm; the magnetoplumbite structure is proved through testing a concertina form of the crystal grain; the maximum coercivity is 5986 Oe at x=0.2; La-doped films possess a wider microwave absorption frequency range with better gross loss angle tangent (tan δ>0.1), from 9 to 10.5 GHz at x=0.2, where the maximum value of tan δ reaches 0.2709. The La-doped films reach smaller nanometer size, better magnetic properties and microwave absorption properties with the doping of lanthanum.     

Effect of annealing on phase composition,structural and magnetic properties of Sm-Co based nanomagnetic material synthesized by sol-gel process

Sm-Co based nanomagnetic material was synthesized by means of a Pechini-type sol-gel process. In this method, a suitable gel-precursor was prepared using respective metal salts and complexing agent such as citric acid. The gel-precursor was dried at 300 °C and then subjected to various reductive annealing temperatures: 350, 500 and 600 °C. The nanopowders so obtained were characterized for their structure, phase composition and magnetic properties. FT-IR studies on the gel-precursor showed the binding of metal cations with the citrate molecules in the form of metal-citrate complex. The gel-precursor, which was annealed at 350 °C showed the presence of both meta-stable cobalt carbide (Co₂C, Co₃C) and Co₃O₄ phases; while the sample annealed at 500 °C indicated the sign of SmCo₅ phase. Upon increasing the reductive annealing temperature to 600 °C, crystalline phase such as fcc-Co and Sm₂C₃ were formed prominently. FE-SEM analysis revealed the change in sample morphology from spherical to oblate spheres upon increasing the annealing temperature. VSM measurements demonstrated ferromagnetic nature at room temperature for all the nanopowders obtained irrespective of their after reductive annealing temperature.     

Effect of pH value on the structural and magnetic properties of nanocrystalline strontium hexaferrite thin films

Strontium hexaferrite SrFe₁₂O₁₉ thin films have been synthesized at different pH, adjusted by NH₄OH, on the Si (1 0 0) substrate using a spin coating sol-gel process. Fourier transform infrared spectroscopy analysis and theoretical calculations were conducted for determination and controlling metal citrates in solution precursors. X-ray diffraction, scanning electron microscopy and vibrating sample magnetometer were applied to evaluate the composition, microstructure, crystallite size and magnetic properties of the SrFe₁₂O₁₉ thin films. Using the solution with pH 7, the approximately single phase strontium hexaferrite thin films with optimum physical properties can be obtained at calcination temperature of 800 °C. The SrFe₁₂O₁₉ thin films derived from the solution with pH 7 after calcination at 800 °C exhibited crystallite size of 42 nm and magnetic properties of M_s=267 emu/cm³ (at 10 kOe), M_r=134 emu/cm³ and H_c=4290 Oe.     

Effect of aluminum substitution on the structural and magnetic properties of cobalt ferrite synthesized by sol-gel auto combustion process

Aluminum substituted cobalt ferrite powders (CoFe_2−xAl_xO₄) with varying composition from 0.0 to 1.0 in the step of 0.2 have been obtained by sol-gel auto combustion technique using citric acid as a fuel. The metal nitrate to fuel ratio was maintained 1:4 throughout the synthesis of CoFe_2−xAl_xO₄. The thermal analysis of as prepared samples is done by TGA technique. The compositional stoichiometry of the prepared samples is confirmed by Energy dispersive X-ray analysis technique. Single phase cubic spinel structure and nano phase structure of the synthesized powders were confirmed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The crystallite size of 16-26 nm was obtained using Scherrer formula. SEM analysis shows the formation of uniform grain growth. The grain size obtained from SEM results is of the order of 30 nm. Maximum specific surface area was observed to be of the order of 52 m²/gm. The highest value of saturation magnetization and coercivity was observed for pure cobalt ferrite sample and it decreases as the aluminum content x increases. A strong co-relation between the saturation magnetization and aluminum content was observed. The decrease in magnetic properties is due to the substitution of aluminum ions in place of Fe³⁺.     

Preparation, magnetic and electromagnetic properties of polyaniline/strontium ferrite/multiwalled carbon nanotubes composite

Strontium ferrite particles were firstly prepared by sol-gel method and self-propagating synthesis, and then the polyaniline/strontium ferrite/multiwalled carbon nanotubes composites were synthesized through in situ polymerization approach. Structure, morphology and properties of the composite were characterized by various instruments. XRD analysis shows that the output of PANI increases with the increase of the content of MWCNTs, due to the large surface area of MWCNTs. Because of the coating of PANI, the outer diameter of MWCNTs increases from 10 nm to 20-40 nm. The electrical conductivity of the composites increases with the amount increase of MWCNTs and reaches 7.2196 S/cm in the presence of 2 g MWCNTs. The coercive force of the composites prepared with 2 g MWCNTs is 7457.17 Oe, which is much bigger than that of SrFe₁₂O₁₉ particles 6145.6 Oe, however, both the saturation magnetization and the remanent magnetization of the composite become much smaller than those of SrFe₁₂O₁₉ particles. The electromagnetic properties of the composite are excellent in the frequency range of 2-18 GHz, which mainly depend on the dielectric loss in the range of 2-9 GHz, and mainly on the magnetic loss in the range of 9-18 GHz.     

The structural and magnetic powders prepared by properties of barium ferrite the sol-gel method

In this paper,M-type hexagonal barium ferrite powders are synthesized using the sol-gel method.A dried precursor heated in air is analyzed in the temperature range from 50 to 1200 C using thermo-gravimetric analysis and differential scanning calorimetry.The effects of the additives and the cacinating temperature on the magnetic properties are investigated,and the results show that single-phase barium ferrite powders can be formed.After heat-treating at 950 C for 4h with 3 wt% additive,the coercivity and saturation magnetization are found to be 440 Oe and 57.9 emu/g,respectively.     

Strontium ferrite nanoparticles synthesized in presence of polyvinylalcohol: Phase composition,microstructural and magnetic properties

Systematic study was devoted to the synthesis of hexagonal strontium ferrite nanoparticles employing polyvinylalcohol as stabilizing agent. Preliminary experiments allowed to select an optimal sol having molar ratio Sr²⁺/Fe³⁺=12${\mathrm{Sr}}^{2+}/{\mathrm{Fe}}^{3+}=12$, weight ratio PVA/[Sr²⁺+Fe³⁺]=1.4$\mathrm{PVA}/[{\mathrm{Sr}}^{2+}+{\mathrm{Fe}}^{3+}]=1.4$ and pH=2.1$\mathrm{pH}=2.1$. The obtained sol were transformed to gels by an evaporation of water at 100 °C and drying at 112 °C under vacuum. The subsequent calcination was carried out for 3 h at 400 °C, achieved by heating rate of 17 K/min. The obtained precursor was used for a detail study of influence of annealing conditions (temperature range 600–700 °C, annealing time 10–190 min) on the resulting properties. Semiquantitative X-ray phase analysis approved a gradual increase of the M-phase content and a gradual growth of M-phase crystallites with temperature and time. Magnetic measurements showed a distinct influence of the phase composition, namely ratio of the contents of M-phase and maghemite on the shape of the magnetic loops, while the crystallite sizes have only a slight effect.     

Tailoring the structural and magnetic properties of sol-gel derived Sm-Co nanogranular films

In this study, we investigated the microstructure, phase evolution and magnetic properties of nanogranular films of Sm-Co compounds processed by the sol-gel method. By controlling the compositional ratio of Sm:Co precursor concentration, nanogranular films consisting of three distinct hard magnetic phases namely, Sm₂Co₇, SmCo₅ and Sm₂Co₁₇ with coercivity values of 1.78, 2.94 and 2.12 kOe, respectively, were obtained through this technique.     

Effect of annealing conditions on structural and magnetic properties of laser ablated copper ferrite thin films

The effect of annealing conditions on structural and magnetic properties of copper ferrite thin films on (100) Si substrates was examined in detail. After deposition, the ferrite thin films were post-annealed in vacuum and in oxygen atmosphere for several hours. It is found that the crystal structure of CuFe₂O₄ thin films changed drastically depending on different heating process. A maximum magnetization was achieved in the film that was vacuum annealed and it decreased remarkably after oxygen annealing.     

Effect of Co substitution on the structural and magnetic properties of Zn–W hexaferrite

The polycrystalline samples of the composition Zn_2−XCo_XBaFe₁₆O₂₇ were prepared by the usual ceramic technique with X=0.4, 0.6, 0.8, 1, 1.2, 1.4 and 1.6. The samples were sintered at 1300 °C for 8 h. The X-ray diffraction patterns confirm the presence of single W-hexagonal phase. The lattice parameters c and a was found to increase by increasing Co content whereas the X-ray density decreases and porosity increases by increasing Co content. The value of saturation magnetization (σ) decreases by increasing Co content due to the decrease of super-exchange interaction. The magnetic moment of the sample were calculated and it showed that in Zn_2−XCo_XBaFe₁₆O₂₇ nearly all Co²⁺ ions are distributed among the octahedral sites of spinel S block. The M–H hysteresis loop for all the samples are clearly showing low coercivity, indicating that all the samples belongs to the family of soft ferrite. The values of coercivity increases by increasing Co content. The far infrared absorption spectrum showed the presence of three absorption bands corresponding to tetrahedral, octahedral and hexahedral sites.     

Effect of doping MnO2 on magnetic properties for M-type barium ferrite

The crystalline structure and magnetic properties of M-type barium ferrite doped with small amounts of MnO₂ (0, 0.25, 0.5, 0.75, 1.0, 1.5, and 2.0 wt%, respectively) have been investigated by means of XRD, SEM and VSM. The results show that the crystalline structures of barium ferrite are still M-type hexagonal structure and Mn ions are distributed homogeneously in both the grains and the grain boundaries. The saturation magnetization and magnetocrystalline anisotropy constants both reach the highest values when x=0.75 wt%. The displacement of Fe ions from 4f₁ to 2b site is mainly responsible for the appearance of the maximum values.     

Effects of In-substitution on the microstructure and magnetic properties of Bi-CVG ferrite with low temperature sintering

[Y_1.05Bi_0.75Ca_1.2](Fe_4.4−xIn_xV_0.6)O₁₂(In_x:Bi-CVG) ferrite material has been prepared successfully by a solid-state reaction method. The effects of In³⁺ substitution and sintering temperatures on the bulk density, microstructure and magnetic properties are performed by X-ray diffraction (XRD), scanning electron microscopy (SEM), materials automatic test system (MATS) and microwave ferrite parameters meter. The results show that In³⁺ can lower the sintering temperatures and enhance the magnetic properties of Bi-CVG ferrite. Besides, all sintered specimens with different In³⁺ contents show a single garnet crystal structure. The specimen of [Y_1.05Bi_0.75Ca_1.2](Fe₄In_0.4V_0.6)O₁₂ sintered at 1075 °C shows homogenous distribution of grain size and densified microstructures. The ferromagnetic resonance linewidth (ΔH) has an increase with In³⁺ contents. Additionally, the sample has the optimum magnetic properties: ρ=5.23 g/cm³, B_r=31.3 mT, H_c=378.8 A/m, 4πM_s=506.2×10⁻⁴ T.     

Investigation of magnetic properties of Al substituted nickel ferrite nanopowders, synthesized by the sol-gel method

NiFe_2−xAl_xO₄ nanopowders, where x is from 0 to 1.5 with a step of 0.5, have been synthesized by the sol-gel method and the effect of non-magnetic aluminum content on their structural and magnetic properties were investigated. The X-ray diffraction (XRD) patterns revealed that the synthesized nanopowders are single phase with a spinel structure. Mean crystallite sizes of the samples were calculated by Scherrer's formula and were in the range 20-31 nm. The morphology of the nanopowders was investigated by TEM and the mean particle sizes of the samples were in the range 55-80 nm. Magnetic hysteresis loops were recorded at room temperature in a maximum applied field of 3000 Oe. The results show that by increasing the aluminum content, the magnetizations of the nanopowders are decreased. This reduction is caused by non-magnetic Al³⁺ ions, which by their substitutions the super exchange interactions between different sites will be reduced. It is also seen that the magnetizations of the nanopowders are lower than those related to their bulk counterparts. This reduction was found to be as a consequence of surface spin disorder. M-T curves of the samples were obtained using a Faraday balance and by which the Curie temperatures of the powders were determined. The results that are obtained show that the Curie temperatures of the nanopowders are higher than those of their bulk counterparts.     

Effect of annealing temperature on structure, magnetic properties and optical characteristics in Zn0.97Cr0.03O nanoparticles

The Cr-doped zinc oxide (Zn_0.97Cr_0.03O) nanoparticles were successfully synthesized by sol-gel method. The relationship between the annealing temperature (400 °C, 450 °C, 500 °C and 600 °C) and the structure, magnetic properties and the optical characteristics of the produced samples was studied. The results indicate that Cr (Cr³⁺) ions at least partially substitute Zn (Zn²⁺) ions successfully. Energy dispersive spectroscopy (EDS) measurement showed the existence of Cr ion in the Cr-doped ZnO. The samples sintered in air under the temperature of 450 °C had single wurtzite ZnO structure with prominent ferromagnetism at room temperature, while in samples sintered in air at 500 °C, a second phase-ZnCr₂O₄ was observed and the samples were not saturated in the field of 10000 Oe. This indicated that they were mixtures of ferromagnetic materials and paramagnetic materials. Compared with the results of the photoluminescence (PL) spectra, it was reasonably concluded that the ferromagnetism observed in the studied samples was originated from the doping of Cr in the lattice of ZnO crystallites.     

Effect of Cd on the structural, magnetic and electrical properties of nanostructured Mn-Zn ferrite

Nanoparticles of Mn_0.5Zn_0.5−xCd_xFe₂O₄ (x=0.0, 0.1, 0.2 and 0.3) have been synthesized by a chemical co-precipitation method. The lattice constant increases with increasing Cd content. X-ray calculations indicate that there is deviation in the cation distribution in the nanostructured spinel ferrite. The dielectric constant and dielectric loss decrease for the samples with Cd content up to x=0.2. However the dielectric constant rises for x=0.3. This is due to an increase in the hopping process at the octahedral (B sites). The dielectric constant increases with increase in temperature, indicating a thermally activated hopping process. The DC resistivity increases with Cd content up to x=0.2 and decreases for Cd content x=0.3. The maximum magnetization of all the samples decreases with increase in Cd content.     

Heat treatment effects on microstructure and magnetic properties of Mn-Zn ferrite powders

Mn-Zn ferrite powders (Mn_0.5Zn_0.5Fe₂O₄) were prepared by the nitrate-citrate auto-combustion method and subsequently annealed in air or argon. The effects of heat treatment temperature on crystalline phases formation, microstructure and magnetic properties of Mn-Zn ferrite were investigated by X-ray diffraction, thermogravimetric and differential thermal analysis, scanning electron microscopy and vibrating sample magnetometer. Ferrites decomposed to Fe₂O₃ and Mn₂O₃ after annealing above 550 °C in air, and had poor magnetic properties. However, Fe₂O₃ and Mn₂O₃ were dissolved after ferrites annealing above 1100 °C. Moreover, the 1200 °C annealed sample showed pure ferrite phase, larger saturation magnetization (M_s=48.15 emu g⁻¹) and lower coercivity (H_c=51 Oe) compared with the auto-combusted ferrite powder (M_s=44.32 emu g⁻¹, H_c=70 Oe). The 600 °C air annealed sample had the largest saturation magnetization (M_s=56.37 emu g⁻¹) and the lowest coercivity (H_c=32 Oe) due to the presence of pure ferrite spinel phase, its microstructure and crystalline size.     

Correlation between site preference and magnetic properties of substituted strontium ferrite thin films

SrFe_12−x(Sn_0.5Zn_0.5)_xO₁₉ thin films with x=0−5 were synthesized by a sol-gel method on thermally oxidized silicon wafer (Si/SiO₂). The site preference and magnetic properties of Zn-Sn substituted strontium ferrite thin films were studied using ⁵⁷Fe Mössbauer spectroscopy and magnetic measurements. Mössbauer spectra displayed that the Zn-Sn ions preferentially occupy the 2b and 4f₂ sites. The preference for these sites is responsible for the anomalous increase in the magnetization at high Zn-Sn substitutions. X-ray diffraction (XRD) patterns and field emission scanning electron microscope (FE-SEM) micrographs demonstrated that single phase c-axis hexagonal ferrite films with rather narrow grain size distribution were obtained. Vibrating sample magnetometer (VSM) was employed to probe magnetic properties of samples. The maximum saturation of magnetization and coercivity at perpendicular direction were 265 emu/g and 6.3 kOe, respectively. It was found that the complex susceptibility has linear variation with static magnetic field.     

Effects of impurity Na ions on the structural and magnetic properties of Ni-Zn-Cu ferrite powders: An improvement for chemical coprecipitation method

Ni-Zn-Cu ferrite powders with nominal composition Ni_0.4−xZn_0.6Cu_xFe₂O₄ (x=0.00-0.20) were prepared via chemical coprecipitation method. X-ray diffractometer, vibrating sample magnetometer, scanning electron microscopy, inductively coupled plasma-atomic emission spectrometry and energy dispersive spectrum were used to study the effects of impurity Na⁺ ions on the structural and magnetic properties. As a result, it was found that the impurity Na⁺ ions affect the crystalline structures and magnetic properties greatly. Moreover, the heterogeneous distribution of impurity Na⁺ ions and the formation of Na compounds retard the phase formation and the grain growth of specimens. Our study also reveals that for the chemical coprecipitation method, a second washing process introduced after drying can eliminate the impurity Na⁺ ions effectually and thus helps in the formation of single-phase structure and the growth of grains, which is very important for the improvement of magnetic properties and the preparation of ferrites via chemical coprecipitation method.     

Effect of temperature of annealing on optical, structural and electrochromic properties of sol-gel dip coated molybdenum oxide films

The sol-gel dip-coating method is used for the preparation of MoO₃ thin films. The 6 layered MoO₃ films were prepared and annealed at various temperatures in the range of 200-350 °C. The band gap value for MoO₃ films were calculated from optical absorption measurements and it is in the range of 3.55-3.73 eV. XRD spectrum reveals (0 2 0) is the major diffraction plane for the films prepared above 250 °C, which reveals the formation of MoO₃ in α-orthorhombic phase. The films prepared at 200 °C and 250 °C exhibits amorphous nature. The FTIR spectrum confirms the presence of Mo-O-Mo and MoO bonds. Nanorods were observed in the SEM images in the case of MoO₃ films prepared above 250 °C. The films prepared at 250 °C exhibit maximum anodic diffusion coefficient of 9.61 × 10⁻¹¹ cm²/s. The same film exhibits the change in optical transmission of 58.4% at 630 nm with the optical density of 0.80.