Composition and magnetic properties of cobalt ferrite nano-particles prepared by the co-precipitation method

Cobalt ferrite nano-particles were prepared using the co-precipitation method followed by annealing treatment. The formation of nano-particles with different composition, microstructure and sizes were confirmed by X-ray diffraction, Raman, thermogravimetric-differential thermal analysis and transmission electron microscope. The magnetic hysteresis loops measured at room temperature revealed smaller effective magnetic anisotropy constant, coercivity and remanence ratio for the samples prepared by adding the NaOH solutions into the mixed solutions of Co²⁺ and Fe³⁺ ions due to the formation of Co³⁺ ions. A small saturation magnetization and an enhanced coercivity were observed for the nano-particles prepared by adding the mixed solutions of Co²⁺ and Fe³⁺ ions into the NaOH solutions, which was related to the formation of outer layers with poor crystallization on the surfaces of the cobalt ferrite nano-crystals. Furthermore, the existence of these outer layers induced the oxidation of Co²⁺ ions in cobalt ferrite nano-crystals at 200 and 300 °C, and led to a large change on the composition and magnetic properties.     

Structure and magnetic properties of nanocrystalline cobalt ferrite powders synthesized using organic acid precursor method

Nanocrystalline octahedra of cobalt ferrite CoFe₂O₄ powders were synthesized using the organic acid precursor route. The effect of the calcination temperature, Fe³⁺/Co²⁺ molar ratio, calcination time and type of organic acid (oxalic, benzoic and tartaric acids) on the formation, crystallite size, microstructure and magnetic properties was studied systematically. The Fe³⁺/Co²⁺ molar ratio was varied from 2 to 1.739 while the annealing temperature was controlled from 400 to 1000 °C for various periods from 0.5 to 2 h. The resulting powders were investigated using X-ray diffraction (XRD) analysis, Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). XRD results indicate that a well crystallized, single spinel cobalt ferrite phase was formed for the precursors annealed at 600-800 °C for 2 h, using oxalic and tartaric acids as precursors for Fe³⁺/Co²⁺ molar ratio 1.818. The crystallite size of as-formed powders was in the range of 38.0-92.6 nm at different operating conditions. The calcination temperature and Fe³⁺/Co²⁺ molar ratio have a significant effect on the microstructure of the produced cobalt ferrite. The microstructure of the produced powders was found to be octahedra-shaped. The crystalline, pure cobalt ferrite powders with magnetic properties having a maximum saturation magnetization (76.1 emu/g) was achieved for the single phase at Fe³⁺/Co²⁺ molar ratio 1.818 and annealing temperature of 600 °C for 2 h using tartaric acid precursor.     

Time-dependent magnetization in co-precipitated cobalt ferrite

A study of the magnetic aftereffect in co-precipitated cobalt ferrite is presented. Measurements of the magnetic viscosity S were performed at room temperature along the demagnetization curve for different applied fields H_ap over a wide range of fields (0 kOe<H_ap<−7 kOe). The interrelation function η=(∂M_rev/∂M_irr)_Hi between the DCD reversible M_rev and irreversible M_irr magnetization components was determined as well. The experimental results for S_η(H_i), where H_i is the internal field, showed a broad distribution with a maximum at H_i=2.7 kOe. However, the irreversible susceptibility χ_irr displays a maximum at H_c=0.75 kOe, the coercivity of the material. The experimental behavior of η and the non-proportionality between S_η and χⁱ_irr suggest that the magnetic viscosity in this material is principally supplied by events of nucleation of inverse domains and the depinning of domain walls. When the main mechanism of reversal magnetization changes to rotation of magnetic moments for all the grains, the magnetic viscosity decreases.     

Temperature dependence of magnetic anisotropy constant in cobalt ferrite nanoparticles

The temperature dependence of the effective magnetic anisotropy constant K(T) of CoFe₂O₄ nanoparticles is obtained based on the SQUID magnetometry measurements and Mössbauer spectroscopy. The variation of the blocking temperature T_B as a function of particle radius r is first determined by associating the particle size distribution and the anisotropy energy barrier distribution deduced from the hysteresis curve and the magnetization decay curve, respectively. Finally, the magnetic anisotropy constant at each temperature is calculated from the relation between r and T_B. The resultant effective magnetic anisotropy constant K(T) decreases markedly with increasing temperature from 1.1×10⁷ J/m³ at 5 K to 0.6×10⁵ J/m³ at 280 K. The attempt time τ₀ is also determined to be 6.1×10⁻¹² s which together with the K(T) best explains the temperature dependence of superparamagnetic fraction in Mössbauer spectra.     

Microstructure characterization and cation distribution of nanocrystalline cobalt ferrite

Nanocrystalline cobalt ferrite has been synthesized using two different methods: ceramic and co-precipitation techniques. The nanocrystalline ferrite phase has been formed after 3 h of sintering at 1000 °C. The structural and microstructural evolutions of the nanophase have been studied using X-ray powder diffraction and the Rietveld method. The refinement result showed that the type of the cationic distribution over the tetrahedral and octahedral sites in the nanocrystalline lattice is partially an inverse spinel. The transmission electronic microscope analysis confirmed the X-ray results. The magnetic properties of the samples were characterized using a vibrating sample magnetometer.     

Influence of vacuum sintering on microstructure and magnetic properties of magnetostrictive cobalt ferrite

Differences in the microstructure and magnetic properties of highly magnetostrictive cobalt ferrite resulting from the effects of different vacuum sintering temperatures and times have been investigated. A vacuum environment was chosen to allow direct comparison of results with air-sintered samples which are more often reported in the literature. It was found that vacuum sintering resulted in the development of a solid solution second phase with composition Co_1−xFe_xO₄ (x∼0.33). There was a decrease in magnetostriction as a result of the formation of the second phase. Furthermore, differences in sintering temperatures were found to have a greater effect on the magnetostriction than differences in sintering times. It was found that the first order cubic anisotropy coefficient initially increased with both sintering temperature and time, before peaking and decreasing to its lowest measured value. The lowest anisotropy was therefore achieved with samples sintered at higher temperatures and longer times.     

Ionic magnetic fluid based on cobalt ferrite nanoparticles: Influence of hydrothermal treatment on the nanoparticle size

Magnetic fluid based on cobalt ferrite nanoparticles was obtained using a hydrothermal treatment added to the Massart procedure. This treatment increases the average size of the nanoparticles from 11.9 to 18.7 nm and also improves the dispersity and crystallinity of the cobalt ferrite particles. The nanoparticles obtained after the hydrothermal treatment were dispersed in aqueous solvent by the classical procedure for ionic magnetic fluids. The ferrofluid thus obtained is stable at pH 7 and may be useful for hyperthermia applications.     

Synthesis and characterization of Ni-Zn ferrite nanoparticles

Nickel zinc ferrite nanoparticles Ni_xZn_1−xFe₂O₄ (x=0.1, 0.3, 0.5) have been synthesized by a chemical co-precipitation method. The samples were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, electron paramagnetic resonance, dc magnetization and ac susceptibility measurements. The X-ray diffraction patterns confirm the synthesis of single crystalline Ni_xZn_1−xFe₂O₄ nanoparticles. The lattice parameter decreases with increase in Ni content resulting in a reduction in lattice strain. Similarly crystallite size increases with the concentration of Ni. The magnetic measurements show the superparamagnetic nature of the samples for x=0.1 and 0.3 whereas for x=0.5 the material is ferromagnetic. The saturation magnetization is 23.95 emu/g and increases with increase in Ni content. The superparamagnetic nature of the samples is supported by the EPR and ac susceptibility measurement studies. The blocking temperature increases with Ni concentration. The increase in blocking temperature is explained by the redistribution of the cations on tetrahedral (A) and octahedral (B) sites.     

Effect of aluminum substitution on the structural and magnetic properties of cobalt ferrite synthesized by sol-gel auto combustion process

Aluminum substituted cobalt ferrite powders (CoFe_2−xAl_xO₄) with varying composition from 0.0 to 1.0 in the step of 0.2 have been obtained by sol-gel auto combustion technique using citric acid as a fuel. The metal nitrate to fuel ratio was maintained 1:4 throughout the synthesis of CoFe_2−xAl_xO₄. The thermal analysis of as prepared samples is done by TGA technique. The compositional stoichiometry of the prepared samples is confirmed by Energy dispersive X-ray analysis technique. Single phase cubic spinel structure and nano phase structure of the synthesized powders were confirmed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The crystallite size of 16-26 nm was obtained using Scherrer formula. SEM analysis shows the formation of uniform grain growth. The grain size obtained from SEM results is of the order of 30 nm. Maximum specific surface area was observed to be of the order of 52 m²/gm. The highest value of saturation magnetization and coercivity was observed for pure cobalt ferrite sample and it decreases as the aluminum content x increases. A strong co-relation between the saturation magnetization and aluminum content was observed. The decrease in magnetic properties is due to the substitution of aluminum ions in place of Fe³⁺.     

Investigations on structural and magnetic properties of cobalt ferrite/silica nanocomposites prepared by the coprecipitation method

Magnetic nanocomposites consisting of cobalt ferrite nanoparticles embedded in silica matrix were prepared by the coprecipitation method using metallic chlorides as precursors for ferrite. Subsequently composites were annealed at 100, 200 and 300 °C for 2 h. The samples were structurally characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). The magnetic properties were measured in the temperature range of 10-300 K using vibrating sample magnetometer (VSM). The effects of thermal treatment on structural and magnetic properties of nanocomposites were investigated. When the samples were annealed, CoFe₂O₄ nanocrystallites were observed in the SiO₂ matrix, whose size increases with increase in annealing temperature. The coercivity and saturation magnetization of nanocomposite (annealed at 300 °C for 2 h) are much higher than that of bulk cobalt ferrite. The realization of adjustable particle sizes and controllable magnetic properties makes the applicability of the CoFe₂O₄ nanocomposite more versatile.     

High magnetostriction coefficient of Mn substituted cobalt ferrite sintered from nanocrystalline powders and after magnetic field annealing

Magnetostriction characteristics of Mn substituted cobalt ferrite, CoFe_2?xMn_xO₄ (0 ≤ x ≤ 0.3), sintered from nanocrystalline powders of average particle size of ～4 nm have been studied. Larger value of magnetostriction at lower magnetic field is achieved after substitution of Mn for Fe. The maximum value of magnetostriction coefficient is not much affected and the slope of the magnetostriction is increased with increasing Mn content. Higher maximum value of magnetostriction coefficient (λ) of 234 ppm comparable to that of the unsubstituted composition with larger strain derivative (dλ/dH) is obtained for x = 0.2 in CoFe_2?xMn_xO₄. The magnetostriction coefficient is increased to 262 ppm with further enhancement in the strain derivative after annealing the sintered compact at 300 °C in a magnetic field of 400 kA/m for 30 min.     

Synthesis and characterization of manganese ferrite nanoparticles by thermal treatment method

Cubic structured manganese ferrite nanoparticles were synthesized by a thermal treatment method followed by calcination at various temperatures from 723 to 873 K. In this investigation, we used polyvinyl pyrrolidon (PVP) as a capping agent to control the agglomeration of the nanoparticles. The characterization studies were conducted by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The average particle sizes of manganese ferrite nanoparticles were determined by TEM, which increased with the calcination temperature from 12 to 22 nm and they had good agreement with XRD results. Fourier transform infrared spectroscopy confirmed the presence of metal oxide bands at all temperatures and the absence of organic bands at 873 K. Magnetic properties were demonstrated by a vibrating sample magnetometer, which showed a super-paramagnetic behavior for all samples and also saturation magnetization (M_s) increases from 3.06 to 15.78 emu/g by increasing the calcination temperature. The magnetic properties were also confirmed by the use of electron paramagnetic resonance spectroscopy, which revealed the existence of unpaired electrons and also measured peak-to-peak line width, resonant magnetic field and the g-factor.     

Dielectric,electrical transport and magnetic properties of Er3+substituted nanocrystalline cobalt ferrite

Erbium substituted cobalt ferrite (CoFe_2−xEr_xO₄; x=0.0–0.2, referred to CFEO) materials were synthesized by sol-gel auto-combustion method. The effect of erbium (Er³⁺) substitution on the crystal structure, dielectric, electrical transport and magnetic properties of cobalt ferrite is evaluated. CoFe_2−xEr_xO₄ ceramics exhibit the spinel cubic structure without any impurity phase for x≤0.10 whereas formation of the ErFeO₃ orthoferrite secondary phase was observed for x≥0.15. All the CFEO samples demonstrate the typical hysteresis (M–H) behavior with a decrease in magnetization as a function of Er content due to weak superexchange interaction. The frequency (f) dependent dielectric constant (ε′) revealed the usual dielectric dispersion. The ε′–f dispersion (f=20 Hz to 1 MHz) fits to the modified Debye's function with more than one ion contributing to the relaxation. The relaxation time and spread factor derived are ∼10⁻⁴ s and ∼0.61(±0.04), respectively. Electrical and dielectric studies indicate that ε′ increases and the dc electrical resistivity decreases as a function of Er content (x≤0.15). Complex impedance analyses confirm only the grain interior contribution to the conduction process. Temperature dependent electrical transport and room temperature ac conductivity (σ_ac) analyses indicate the semiconducting nature and small polaron hopping.     

Tape casting of cobalt ferrite from nonaqueous slurry

This paper describes the fabrication of CoFe₂O₄ thick films using the tape casting method from nonaqueous slurry. CoFe₂O₄ particles with average size of ∼800 nm were prepared by the solid-state reaction method. Sediment volumes and viscosity were tested to study the effects of dispersant in reducing aggregations in slurry. Slurry with 0.25 wt% dispersant amounts and 41.3 wt% solid content showed the optimal stability and rheological properties. A tape velocity of 8 cm/s was used in this study considering the non-Newtonian flow behavior at low shear rate. CoFe₂O₄ ceramic films sintered at 1150 °C for 2 h have dense structure (relative density of 94%) and exhibited ferromagnetic properties with in-plane saturation magnetization of ∼324 emu/cm³.     

Structural characterization and magnetic properties of superparamagnetic zinc ferrite nanoparticles synthesized by the coprecipitation method

Single phase zinc ferrite (ZnFe₂O₄) nanoparticles have been prepared by the coprecipitation method without any subsequent calcination. The effects of precipitation temperature in the range 20–80 °C on the structural and the magnetic properties of zinc ferrite nanoparticles were investigated. The crystallite size, microstructure and magnetic properties of the prepared nanoparticles were studied using X-ray diffraction (XRD), Fourier transmission infrared spectrum, transmission electron microscope (TEM), energy dispersive X-ray spectrometer and vibrating sample magnetometer. The XRD results showed that the coprecipitated nanoparticles were single phase zinc ferrite with mixture of normal and inverse spinel structures. Furthermore, ZnFe₂O₄ nanoparticles have the crystallite size in the range 5–10 nm, as confirmed by TEM. The magnetic measurements exhibited that the zinc ferrite nanoparticles synthesized at 40 °C were superparamagnetic with the maximum magnetization of 7.3 emu/g at 10 kOe.     

Synthesis and characterization of cobalt/gold bimetallic nanoparticles

Cobalt/gold (Co/Au) bimetallic nanoparticles are prepared by chemically reducing gold (III) chloride to gold in the presence of pre-synthesized Co nanoparticles. Transmission electron microscopy (TEM), ultraviolet-visible (UV-vis) absorption spectrometry, and a superconducting quantum interference device (SQUID) magnetometer have been used to characterize as-prepared bimetallic nanoparticles. Our findings demonstrate Au not only grows onto Co nanoparticles, forming a surface coating, but also diffuses into Co nanoparticles. The introduction of Au alters the crystalline structure of Co nanoparticles and changes their magnetic properties. Dodecanethiols induce a reorganization of as-prepared Co/Au bimetallic nanoparticles.     

Synthesis and characterization of lithium ferrite by oxalate precursor route

Nanocrystalline lithium ferrite (LiFe₅O₈) powders have been synthesized by oxalate precursor route. The effects of Fe³⁺/Li⁺ mole ratio, and annealing temperature on the formation, crystalline size, morphology and magnetic properties were systematically studied. The Fe³⁺/Li⁺ mole ratio was controlled from 5 to 3.33 while the annealing temperature was controlled from 600 to 1100 °C. The resultant powders were investigated by differential thermal analyzer (DTA), X-ray diffractometer (XRD), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). DTA results showed that LiFe₅O₈ phase started to form at around 520 °C. XRD indicated that LiFe₅O₈ phase always contained α-Fe₂O₃ impurity and the hematite phase formation increased by increasing the annealing temperature ?850 °C for different Fe³⁺/Li⁺ mole ratios 5, 4.55 and 3.85. Moreover, lithium ferrite phase was formed with high conversion percentage at critical annealing temperature 750–800 °C. Single well crystalline LiFe₅O₈ phase was obtained at Fe³⁺/Li⁺ mole ratio 3.33 and annealing temperatures from 800 to 1000 °C. Maximum saturation magnetization (68.7 emu/g) was achieved for the formed lithium ferrite phase at Fe³⁺/Li⁺ mole ratio 3.33 and annealing temperature 1000 °C.     

Cobalt ferrite nanoparticles: The control of the particle size and surface state and their effects on magnetic properties

In order to improve the efficacy of magnetic fluid hyperthermia (MFH) mediators, we synthesised cobalt ferrite nanoparticles with different sizes (between 5 and 7 nm) via successive polyol synthesis. The static and dynamic magnetic properties of the prepared particles, dispersed in a solid matrix, were investigated in order to evaluate the possibility of applying cobalt ferrite as magnetic susceptors in MFH. The effect on magnetic properties coming from the surface anchoring of the model molecule cetyl phosphate, was also investigated.     

Structural and magnetic properties of nanocrystalline stannic substituted cobalt ferrite

The structural and magnetic properties of the spinel ferrite system Co_1+xFe_2−2xSn_xO₄ (x=0.0–1.0) have been studied. Samples in the series were prepared by the ceramic technique. The structural and microstructural evolutions of the nanophase have been studied using X-ray powder diffraction and the Rietveld method. The refinement result showed that the type of the cationic distribution over the tetrahedral and octahedral sites in the nanocrystalline lattice is partially an inverse spinel. Far infrared absorption spectra show two significant absorption bands, around 600 cm⁻¹ and 425 cm⁻¹, which are respectively attributed to tetrahedral (A) and octahedral [B] vibrations of the spinel. Scanning Electron Microscopy (SEM) was used to study surface morphology. SEM images reveal particles in the nanosize range. The transmission electronic microscope (TEM) reveals that the grains are spherical in shape. TEM analysis confirmed the X-ray results. The magnetic properties of the prepared samples were characterized by using a vibrating sample magnetometer.     

Fabrication and magnetic property analysis of monodisperse manganese-zinc ferrite nanospheres

Monodisperse Mn-Zn ferrite (Mn_1−xZn_xFe₂O₄) nanospheres have been prepared via a simple solvothermal method. The as-synthesized samples were characterized in detail by X-ray diffraction pattern (XRD), transmission electron microscope (TEM), high-solution transmission electron microscope (HRTEM), select area electron diffraction pattern (SAED), scanning electron microscope (SEM), and vibrating sample magnetometer (VSM). The results show that a large number of the high-purity Mn_1−xZn_xFe₂O₄ nanocrystallites were synthesized and these nanocrystallites oriented aggregated to nanospheres. The dependence of magnetic properties of Mn_1−xZn_xFe₂O₄ nanospheres on the composition content x of Zn was studied. The maximum saturation magnetization value of the as-prepared sample (Mn_0.6Zn_0.4Fe₂O₄) reached 52.4 emu g⁻¹.