Trace determination of beta-lactam antibiotics in environmental aqueous samples using off-line and on-line preconcentration in capillary electrophoresis

A sensitive and reliable method using capillary zone electrophoresis with UV-diode array detection (CZE-DAD) has been developed and validated for trace determination of beta-lactam antibiotics in waste, well and river water matrices. Due to the lack of sensitivity of the UV-vis detection, a solvent extraction/solid-phase extraction (SPE) method applied for off-line preconcentration and cleanup of water samples, in combination with an on-line preconcentration methodology named large volume sample stacking (LVSS) have been applied. The analytes included nafcillin, dicloxacillin, cloxacillin, oxacillin, ampicillin, penicillin G and amoxicillin. Average recoveries for water samples fortified with the studied beta-lactams at different concentration levels (1.0, 2.0 and 4.0 microg/L) were ranging between 94 and 99%, with relative standard deviations (RSDs) lower than 10%. The precision, calculated as intra-day and inter-day standard deviations fell within acceptable ranges (3.3-7.2%). The limits of detection were estimated to range between 0.08 and 0.80 microgL(-1) for the studied compounds. All the samples analyzed were negative for all the analytes at these levels of concentration and the method showed its usefulness for the detection of these widely applied beta-lactam antibiotics in different kinds of waters.     

Profiling and quantifying polar lipids in milk by hydrophilic interaction liquid chromatography coupled with evaporative light-scattering and mass spectrometry detection

In this work, a high-performance liquid chromatography with evaporative light scattering detection method has been developed and applied for quantification of the polar content of the lipid fraction in milk samples of different origin. From a chromatographic stand-point, a 4.6-mm I.D. hydrophilic interaction liquid chromatography column was employed to attain a baseline separation of major phospholipid classes contained in the various milk samples tested. Quantitative analysis was performed by the external calibration method using reference material solutions in the 5–100 mg/L concentration range. Analytical recoveries ranging from 57 to 100 %, and repeatability data lower than 8.04 % were obtained on a skimmed cow’s milk sample. The crude cow milk was the most abundant (0.04 %) in phospholipids and donkey milk was the poorest (0.004 %). Quantitative differences were determined in the phospholipid content of the milk samples tested. Finally, characterization of phospholipid profile and fatty acid composition of the different samples was carried out by an ion trap-time of flight mass spectrometer and gas chromatography coupled to flame ionization and mass spectrometry detection. A thorough screening of the polar lipid composition of milk samples of different origin is here outlined, for the first time.     

Application of capillary zone electrophoresis with large-volume sample stacking to the sensitive determination of sulfonamides in meat and ground water

A CZE method with UV-Vis detection has been established and validated for the determination of nine sulfonamides: sulfapyridine, sulfamethazine, sulfamerazine, sulfamether, sulfadiazine, sulfadimethoxine, sulfamethoxazole, sulfachlorpyridazine, and sulfamethizole. Optimum separation was obtained on a 64.5 cm x 75 microm bubble cell capillary using a buffer containing 45 mM sodium phosphate and 10% methanol at pH 7.3, with temperature and voltage of 27 degrees C and 25 kV, respectively. p-Aminobenzoic acid was used as an internal standard . Taking into account the lack of sensitivity of the UV-Vis detection, the application of an on-line preconcentration methodology, such as large-volume sample stacking with polarity switching has been proposed. This procedure combined with a solvent extraction/SPE method applied for off-line preconcentration and cleanup provides a significant improvement in the LODs, ranging from 2.59 to 22.95 mug/L for the studied compounds; the quantification of these residues being possible below the levels established by EU legislation in animal food products, such as meat. Satisfactory recoveries were also obtained in the analysis of these compounds in ground water.     

Synthesis, characterization and application of modified Pd nanoparticles as preconcentration probes for selective enrichment/analysis of proteins via hydrophobic interactions from real-world samples using nanoparticle-liquid-liquid microextraction coupled to matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

We introduce a novel preconcentrating technique by using surface modification of palladium nanoparticles (Pd-NPs) with octadecane thiol (ODT) prepared in toluene for selective and sensitive extraction of proteins (insulin, ubiquitin, lysozyme) from a variety of real-world samples including pancreas, mushroom, soybean and milk using nanoparticle-liquid-liquid microextraction (NP-LLME) coupled to matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-MS). The limit of detection (LOD) values obtained for gramicidin D and insulin in water and urine are between 17-37 nM (17-37 fmol) (with RSDs ranging from 5.3-7.2%) which are 10-20-fold enhancement in detection sensitivity compared with conventional MALDI-MS. The optimal sample pH for highest extraction efficiency of insulin, ubiquitin and lysozyme from biological samples was observed at sample pH ～ pI which could be due to the enhancement of hydrophobic interactions between proteins with the hydrophobic ligands of Pd-ODT NPs. In addition, we also found that with the addition of 1?M NaCl, signals could be significantly enhanced by using the current approach. It is an efficient, straightforward, sensitive and selective nanoprobe which can be widely applied for separation, enrichment and preconcentration of peptides or proteins from complex biological samples in proteome research.     

Determination of quinolones in milk samples using a combination of magnetic solid-phase extraction and capillary electrophoresis

A magnetic solid-phase extraction (MSPE) method combined with capillary electrophoresis for the simultaneous determination of seven quinolones (QNs) (danofloxacin, ciprofloxacin, marbofloxacin, enrofloxacin, difloxacin, oxolinic acid, and flumequine), using (S)-(+)-6-methoxy-α-methyl-2-naphthaleneacetic acid as internal standard, in milk samples was developed. The variables involved in the preconcentration magnetic procedure were: the composition of the magnetic support composition, the sample pH, and the weight of magnetic adsorbent used. The variables were optimized using a simplex-lattice design. Different magnetite covered with octyl-phenyl silica adsorbents were synthesized by varying the molar ratio of phenyltrimethylsilane and octyltrimethoxysilane; the solids were evaluated for QN preconcentration. Under optimal conditions, a linear range was obtained from 27 to 1000 μg L(-1) with limits of detection ranging from 9 to 12 μg L(-1) for the seven QNs. The absolute recoveries of the seven QNs at three different spiked levels (40, 150, and 400 μg L(-1) ) ranged from 74% to 98% with a relative standard deviation less than 10% in all cases. The proposed method was applied to analyze 20 whole milk samples of different brands. All samples were positive for the presence of QN residues; in some cases, extract dilution was required. The concentrations found are in the range from 31.1 to 5047.3 μg L(-1) . Marbofloxacin was the most frequently found. The method proposed offers advantages in terms of simplicity, sensitivity, efficiency, cost, and analysis time making it an alternative for the analysis of QNs in whole milk samples.     

磺化改性聚四氟乙烯纤维固相萃取-高效液相色谱联用测定奶制品中的三聚氰胺

采用新型固相萃取材料磺化的甲基丙烯酸缩水甘油酯接枝聚四氟乙烯（PTFE-g-GMA-SO3H）纤维填充微柱预富集和流动注射(FI)与高效液相色谱(HPLC)联用测定样品中痕量的三聚氰胺。 建立了以该纤维作为吸附剂在线测定奶制品中三聚氰胺的新方法。 对三聚氰胺的富集与洗脱条件进行了优化,并得出三聚氰胺的分析特性：该方法对三聚氰胺的检出限为1.13×10-2 mg/L,富集倍数为300,RSD为7.6%（n=9,三聚氰胺质量浓度为0.2 mg/L）。 该方法应用于2种奶制品中的痕量三聚氰胺的测定,样品加标回收率分别为98%和102.5%。     

Development and validation of a solid-phase extraction method coupled to liquid chromatography with fluorescence detection for the determination of fluoroquinolone residues in powdered infant formulae. Application to the analysis of samples from the Spanish and Latin American market

This paper describes a new method for the effective extraction, clean-up and chromatographic analysis of residues of four fluoroquinolones (ciprofloxacin, enrofloxacin, danofloxacin and sarafloxacin) in powdered infant formulae and follow-on preparations. Samples were reconstituted following the manufacturer's recommendations and treated with trichloroacetic acid in methanol 10% (w/v) for deproteinization. Two solid-phase extraction cartridges have been evaluated for sample clean-up and preconcentration, Strata Screen A and Strata X and the later provided the best recoveries for all the analytes tested. Chromatographic analysis has been carried out using a polar endcapped column (AQUA C(18)) and fluorescence detection, with lomefloxacin (LOME) as internal standard. Method validation has been performed according to European Commission Decision 2002/657/EC criteria, in terms of linearity, recovery, precision, specificity, decision limit (CC(alpha)) and detection capability (CC(beta)). Typical recoveries ranged between 70 and 110% at levels below and above the maximum residue limits of the target analytes in bovine milk, with an excellent intralab reproducibility (RSDs<7%). Matrix effects did not significantly affect method accuracy, as evidenced by analyzing different brands of milk. The method has been successfully applied to the analysis of 100 samples of infant and follow-on formulae of the Spanish and Latin American market, using LC-MS/MS as confirmatory technique.     

Separation and preconcentration of cadmium ions in natural water using a liquid membrane system with 2-acetylpyridine benzoylhydrazone as carrier by flame atomic absorption spectrometry

A method for the determination of Cd in natural water by flame atomic absorption spectrometry after separation and preconcentration with a bulk liquid membrane containing 2-acetylpyridine benzoylhydrazone as mobile carrier dissolved in toluene has been developed. Effects of carrier concentration, volume of organic phase and pH of feed and receiving solutions on the flux for Cd across the membrane have been studied, being optimized by the modified simplex method. Optimum values for these variables were: carrier concentration of 0.84 g l⁻¹, 74 ml of toluene, pH 7.8 in the feed solution and 0.06 mol l⁻¹ of HNO₃ in the receiving solution, allowing a preconcentration factor of 17.9. The preconcentration step required 7 h to be accomplished. The recovery of Cd at optimum conditions was 101.0±2.7%, even with saline matrix, with good relative standard deviation (2.5%) at 95% confidence level. The detection limit of blank sample was 6 ng l⁻¹ of Cd. The method was validated using a certified reference material (TMDA-62) and also applied successfully to the analysis of Cd in four samples of seawater collected from the coast of Huelva (Spain). The relative errors of determinations were −7.6% for certified reference material and ranging between +2.4 and +7.1%, for samples of seawater (obtained between the results of the proposed and differential pulse anodic stripping voltammetry methods).     

Solid phase extraction of trace amounts of uranium(VI) from water samples using 8-hydroxyquinoline immobilized on surfactant-coated alumina

A simple and reliable method has been developed for the determination of uranium(VI). The method is based on the separation and preconcentration of uranium(VI) using a column packed with 8-hydroxyquinoline immobilized on surfactant coated alumina prior to its spectrophotometric determination with arsenazo III. The effect of pH, sample flow rate and volume, elution conditions, and foreign ions on the sorption of uranium(VI) has been investigated. A preconcentration factor of 200 was achieved by passing 1000 mL of sample through the column. The relative standard deviation for 10 replicate analyses at the 100 ng/mL level of uranium(VI) was 2.1% and the detection limit was 0.12 ng/mL. The method was success-fully applied to the determination of uranium in natural water samples. The accuracy was assessed through recovery experiments and the analysis of a certified reference material.     

Solid phase extraction of trace amounts of uranium(VI) from water samples using 8-hydroxyquinoline immobilized on surfactant-coated alumina

A simple and reliable method has been developed for the determination of uranium(VI). The method is based on the separation and preconcentration of uranium(VI) using a column packed with 8-hydroxyquinoline immobilized on surfactant coated alumina prior to its spectrophotometry determination with Arsenazo III. The effect of pH, sample flow rate and volume, elution conditions, and foreign ions on the sorption of uranium(VI) has been investigated. A preconcentration factor of 200 was achieved by passing 1000 mL of sample through the column. The relative standard deviation for 10 replicate analyses at the 100 ng/mL level of uranium(VI) was 2.1% and the detection limit was 0.12 ng/mL. The method was successfully applied to the determination of uranium in natural water samples. The accuracy was assessed through recovery experiments and the analysis of a certified reference material.     

Application of multiwalled carbon nanotubes as solid phase extraction sorbent for preconcentration of trace copper in water samples

The adsorption behavior of multiwalled carbon nanotubes (MWNTs) toward copper has been investigated systemically, and a new method has been developed for the determination of trace copper in water samples based on preconcentration with a microcolumn packed with MWNTs prior to its determination by flame atomic absorption spectrometry. The optimum experimental parameters for preconcentration of copper, such as pH of the sample, sample flow rate and volume, elution solution and interfering ions, have been investigated. Copper can be quantitatively retained by MWNTs in the pH range 5-8, and then eluted completely with 0.5 M HNO3. The detection limit of this method for Cu was 0.42 ng/mL, and the RSD was 3.5% at the 10 ng/mL Cu level. The method was validated using a certified reference material, and has been successfully applied for the determination of trace copper in water samples.     

Trace analysis of aminoglycoside antibiotics in bovine milk by MEKC with LIF detection

This work describes a straightforward and sensitive method for the multi-residue analysis of aminoglycoside antibiotics (kanamycin B, amikacin, neomycin B and paromomycin I) in bovine milk samples. The method involves the pre-capillary derivatization of antibiotics with sulfoindocyanine succinimidyl ester (Cy5) and their separation and determination by MEKC with LIF detection. The optimum procedure includes a derivatization step of the antibiotics at 25 degrees C for 30 min and direct injection for MEKC analysis, which is performed in about 20 min by using borate buffer (35 mM; pH 9.2) with 55 mM SDS as an anionic surfactant and 20% ACN as the organic modifier. Under these conditions, dynamic ranges of 10-500 microg/L and RSDs (within-day precision) from 3.8 to 5.3% were obtained. These results indicate that the proposed MEKC-LIF method is useful as a selective and sensitive tool for the determination of these antibiotics and surpasses other reported electrophoretic alternatives. Finally, the method was successfully applied to bovine milk samples after a simple solid-phase extraction clean-up and preconcentration procedure. The aminoglycosides were readily detected at 0.5-1.5 microg/kg levels with average recoveries ranging from 89.4 to 93.3%.     

Improved liquid chromatographic determination of nine currently used (fluoro)quinolones with fluorescence and mass spectrometric detection for environmental samples

An HPLC method using C18-modified silica as stationary phase has been developed for environmental trace analysis of nine (fluoro)quinolones. Detection is done by fluorescence measurement or MS using the modes of SIM and selected reaction monitoring (SRM). Best separation is achieved with a gradient consisting of 50 mM formic acid and methanol, which is fully compatible with MS coupling. LOQs (S/N of 10) for fluorescence detection are between 10 and 60 microg/L, depending on the analyte. MS detection (SIM and SRM) yields LOQs that are better by a factor of at least an order of magnitude. Sample preconcentration and sample clean-up is accomplished by SPE (preconcentration factor of 1000), leading to LOQs in the low ng/L range. Recoveries of the preconcentration procedure are better than 80% for all analytes. The suitability for real samples has been demonstrated by analyzing surface waters, municipal waste waters, sewage treatment plant effluents, sewage sludge, and sediment taken from rivers and fish ponds. The method should also be useful for determination of residues of (fluoro)quinolones in food or other matrices. The degradation of the (fluoro)quinolones has been examined over 5 days in order to get information about the decomposition rate and the degradation products eventually occurring in the environment.     

Flow-injection flame atomic absorption spectrometric determination of trace amounts of cadmium in solid and semisolid milk products coupling a continuous ultrasound-assisted extraction system with the online preconcentration on a chelating aminomethylphosphoric acid resin

A new sensitive and low-cost method that combines continuous acid extraction, online preconcentration, and flame atomic absorption spectrometry for cadmium determination at microg levels in solid and semisolid milk products is described. A continuous ultrasound-assisted extraction system is used to carry out the dynamic acid extraction step. The acid extract is preconcentrated online on a minicolumn packed with a chelating resin (Chelite P, with aminomethylphosphoric acid groups), and the retained cadmium is eluted with hydrochloric acid and continuously monitored by flame atomic absorption spectrometry. An experimental design (Plackett-Burman 2-6*3/16) is used to optimize the continuous extraction and the preconcentration step. The method allowed a total sampling frequency of 28 samples/h. A good precision of the whole procedure (3.0% relative standard deviation) for a cheese sample containing 0.103 +/- 0.004 microg/g Cd (dry mass), a high enrichment factor (20.5), and detection and quantification limits of 0.014 and 0.067 microg/g, respectively, for a 60 mg of sample were obtained with this methodology. The method was successfully applied to the determination of trace amounts of cadmium in solid and semisolid milk products, such as cheese and yogurt samples.     

Application of flow injection on-line electrothermal atomic absorption spectrometry to the determination of rhodium

A fully automated procedure for the determination of rhodium has been developed using flow injection (FI) on-line microcolumn preconcentration coupled with electrothermal atomic absorption spectrometry (ETAAS). The proposed FI manifold and its operation make possible the introduction of the total eluate volume into the graphite atomizer, avoiding the necessity for optimisation of subsampling the eluate. Rhodium is adsorbed on a microcolumn packed with 1,5-bis(di-2-pyridyl)methylene thiocarbohydrazide immobilized on silica gel (DPTH-gel). Under the optimum conditions, using a 60 s preconcentration time, a sample flow rate of 3.5 mL min(-1) and an injection volume of eluent of 50 microL, a linear calibration graph was obtained from 1 to at least 40 ng mL(-1) and the detection limit was 1 ng mL(-1). The proposed method has been successfully applied to the analysis of samples. Its performance was investigated against certified reference catalyst sample SRM-2557 and by recovery measurements on spiked samples (soil, foods and beverages).     

On-line preconcentration and speciation of arsenic by flow injection hydride generation atomic absorption spectrophotometry

A flow injection-column preconcentration-hydride generation atomic absorption spectrophotometric (FI-column-HGAAS) method was developed for determining μg/l levels of As(III) and As(V) in water samples, with simultaneous preconcentration and speciation. The speciation scheme involved determining As(V) at neutral pH and As(III + V) at pH 12, with As(III) obtained by difference. The enrichment factor (EF) increased with increase in sample loading volume from 2.5 to 10 ml, and for preconcentration using the chloride-form anion exchange column, EFs ranged from 5 to 48 for As(V) and 4 to 24 for As(III + V), with corresponding detection limits of 0.03-0.3 and 0.07-0.3 μg/l. Linear concentration range (LCR) also varied with sample loading volume, and for a 5-ml sample was 0.3-5 and 0.2-8 μg/l for As(V) and As(III + V), respectively. Sample throughput, which decreased with increase in sample volume, was 8-17 samples/h. For the hydroxide-form column, the EFS for 2.5-10 ml samples were 3-23 for As(V) and 2-15 for As(III + V), with corresponding detection limits of 0.07-0.4 and 0.1-0.5 μg/l. The LCR for a 5-ml sample was 0.3-10 μg/l for As(V) and 0.2-20 μg/l for As(III + V). Sample throughput was 10-20 samples/h. The developed method has been effectively applied to tap water and mineral water samples, with recoveries ranging from 90 to 102% for 5-ml samples passed through the two columns.     

Method validation for the determination of lead in raw cow's milk by electrothermal atomic absorption spectrometry

In this study, lead in raw cow's milk has been determined by validated electrothermal atomic absorption spectrometry (ETAAS) with Zeeman-effect background correction. Maximum pyrolysis and optimum atomization temperatures of lead were determined in the presence of modifiers. Pd + Mg(NO3)2 has been found a powerful modifier mixture for the determination of lead. The analytical parameters of the method such as limit of detection, limit of quantification and the effect of interfering ions have been investigated. The detection limit (3sigma) achieved by the method was calculated to be 0.62 ng/mL for Pb. Repeatability of the method evaluated as the relative standard deviation of 16-17 replicates using 5 ng/mL, under optimum experimental conditions were about 1.5% for synthetic sample solution and about 3% for real sample (N = 5). The described method has been validated by analyzing certified reference material (BCR-CRM 150) and by comparing the results with those obtained by inductively coupled plasma mass spectrometry (ICP-MS). The validated method was applied to raw cow's milk samples produced in 7 different regions of Turkey in 2003-2004. Raw cow's milk contained a mean (range) of 31.4 (2.5 - 313) microg kg(-1) lead with a relative error below 2%.     

Speciation of Cr(III) and Cr(VI) in water after preconcentration of its 1,5-diphenylcarbazone complex on amberlite XAD-16 resin and determination by FAAS

A simple and sensitive method for the speciation, separation and preconcentration of Cr(VI) and Cr(III) in tap water was developed. Cr(VI) has been separated from Cr(III) and preconcentrated as its 1,5-diphenylcarbazone complex by using a column containing Amberlite XAD-16 resin and determined by FAAS. Total chromium has also been determined by FAAS after conversion of Cr(III) to Cr(VI) by oxidation with KMnO₄. Then, Cr(III) has been calculated by subtracting Cr(VI) from the total. The effect of acidity, amount of adsorbent, eluent type and flow rate of the sample solution on to the preconcentration procedure has been investigated. The retained Cr(VI) complex was eluated with 10 ml of 0.05 mol l⁻¹ H₂SO₄ solution in methanol. The recovery of Cr(VI) was 99.7±0.7 at 95% confidence level. The highest preconcentration factor was 25 for a 250 ml sample volume. The detection limit of Cr(VI) was found as 45 μg l⁻¹. The adsorption capacity of the resin was found as 0.4 mg g⁻¹ for Cr (VI). The effect of interfering ions has also been studied. The proposed method was applied to tap water samples and chromium species have been determined with the relative error <3%.     

Multiresidue method for the analysis of multiclass pesticides in agricultural products by gas chromatography-tandem mass spectrometry

A multiresidue method is described for determining 55 organophosphorus and organochlorinated compounds and pyrethroids commonly used in crop protection. Pesticide residues are extracted from samples with a mixture of ethyl acetate and sodium sulfate, obtaining a final preconcentration of I mg sample (ml extract)(-1). No additional clean-up steps are necessary. Analysis is performed by gas chromatography by using a combination of positive chemical ionisation (PCI) and electron impact (EI) ionisation modes and tandem mass spectrometry (GC-PCI/EI-MS-MS). Good sensitivity and selectivity of the method are obtained with limits of detection (LODs) ranging from 0.07 to 4.21 microg kg(-1) in all the cases, except for methamidophos, permethrin, cypermethrin and difenconazol. Average recoveries between 52 and 114% are obtained and good linearity is observed in the studied ranges (r > or = 0.994). The RSD values are < or = 29% in all the cases. The method has been applied to the analysis of 178 vegetable samples, as a part of the monitoring programme of the Association of Producers and Exporters of Fruits and Vegetables of Almería (COEXPHAL) and quality control systems applied during the assays have demonstrated a good performance and stability with time.     

On-line complexation/preconcentration system for the determination of lead in wine by inductively coupled plasma-atomic emission spectrometry with ultrasonic nebulization

An on-line lead preconcentration and determination system implemented with inductively coupled plasma-atomic emission spectrometry (ICP-AES) with ultrasonic nebulization (USN) in association with flow injection was studied. For the preconcentration of lead, a Pb-quinolin-8-ol complex was formed on-line at pH 6.8 and retained on Amberlite XAD-16 resin. The lead was removed from the microcolumn by countercurrent elution with nitric acid. A total enhancement factor of 225 was obtained with respect to ICP-AES with pneumatic nebulization (15.0 for USN and 15.0 for the column). The detection limit for Pb for the preconcentration of a 10 mL wine sample was 0.15 microg/L. The precision for 10 replicate determinations at a Pb level of 25 microg/L was a relative standard deviation of 2.5%, calculated from the peak heights obtained. The calibration graph obtained by using the preconcentration system for lead was linear with a correlation coefficient of 0.9995 for levels near the detection limit up to > or = 1000 microg/L. The method was successfully applied to the determination of lead in wine samples.