Molecular mechanism of formation of supported platinum catalysts of the Pt/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> family

Certain stages of the classical procedure for preparing aluminum-platinum catalysts, whose understanding is important from both the basic and practical viewpoints, are considered on the molecular level. Properties of both participants (active component precursor solution and oxide surface) are shown to be inhomogeneous, which can affect interaction of the components at the fixing stage. Existing views (and their evolution) on the mechanism of adsorption of platinum complexes from aqueous solutions on aluminum oxide surface are discussed. The role of chemical processes on the stage of fixing precursor on the electronic and structural properties of the supported metal is demonstrates. Strong metal-support interaction is shown to endow platinum with specific adsorption and catalytic properties in hydrocarbon transformation reactions.     

Kinetic studies on the hydrogenation of nitrate in water using Rh/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Rh-Cu/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Liquid-phase reduction NO ₃ ⁻ using monometallic and bimetallic catalysts (5% Rh/Al₂O₃, 5% Rh-0.5% Cu/Al₂O₃, 5% Rh-1.5% Cu/Al₂O₃, 5% Rh-5% Cu/Al₂O₃ and a physical mixture of 5% Rh/Al₂O₃ and 1.5% Cu/Al₂O₃) was studied in a slurry reactor operating at atmospheric pressure. Kinetic measurements were performed for a low concentration of nitrate (0.4 × 10⁻³−3.2 × 10⁻³ mol dm⁻³) and the temperature range 293–313 K. From the experimental data, it was found that the reduction of nitrate is first order with respect to nitrate. On the basis of the rate constants, the apparent activation energy was established using a graphic method. Published in Russian in Kinetika i Kataliz, 2007, Vol. 48, No. 6, pp. 881–886. This article was submitted by the authors in English.     

One-pot synthesis of Nb-modified Al<Subscript>2</Subscript>O<Subscript>3</Subscript> support for NiMo hydrodesulfurization catalysts

The effect of Nb as a support modifier on the NiMo₆/Al₂O₃–Nb₂O₅(x) (x?=?0, 1, 4, and 8?wt% Nb) catalysts was studied. The supports were prepared by one-pot coprecipitation from soluble precursors. The XRF analysis of the catalysts showed that the contents of Mo and Ni increased slightly with the presence of Nb. Micropore area and pore volume augmented importantly with Nb content, resulting in pore diameters between 5.3 and 9.3?nm. XPS analysis showed that the presence of Nb decreases the active metal–support interaction, improving the Mo and Ni sulfidation degree. The Raman spectra of sulfided catalysts suggested an increase in the number of layers of MoS₂ in the presence of Nb. Generally, the thiophene HDS activity at normal pressure of sulfided NiMo₆/Al₂O₃–Nb₂O₅(8) was greater than that of the sulfided catalysts with x?=?0, 1, and 4?wt% Nb, which can be attributed to the Nb promotion that would have an effect on the type of active site (Brønsted or Lewis acidic sites), since the number of sites by CO chemisorption for sulfided NiMo₆/Al₂O₃–Nb₂O₅(x) did not show correlation with the catalytic activity. The high-pressure HDS activity of dibenzothiophene was also greater in the presence of Nb, and the hydrogenation route was preferred for the Nb-promoted solid, while the unpromoted one showed a larger yield of direct desulfurization products.

Open image in new window

     

Reactivation of CoMo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> hydrotreating catalysts with chelating agents

Effect of various chelating components, multibasic carboxylic acids and glycols, used to prepare hydrotreating catalysts on the activity regeneration of calcined hydrotreating catalysts was studied. Reactivated catalyst samples were tested in a model reaction of hydrodesulfurization of dibenzothiophene. It was shown that the treatment of calcined catalysts with the chelating components leads to an increase in the catalytic activity. The best catalytic characteristics are observed for the catalyst reactivated with a solution containing citric acid and triethylene glycol.     

Catalytic properties of Pt/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts in the aqueous-phase reforming of ethylene glycol: Effect of the alumina support

The influence of the alumina support on the catalytic activity of Pt/Al₂O₃ catalysts in aqueous phase reforming of ethylene glycol to hydrogen was studied. The catalysts were prepared by impregnation of γ-, δ-, and α-alumina with H₂PtCl₆. The highest rate of hydrogen production (452 μmol min⁻¹ g⁻¹) obtained with the Pt/α-Al₂O₃ catalyst can be related to the highest extent of dispersion of Pt on α-Al₂O₃. XPS, TEM-EDX and TPR-H₂ measurements showed the absence of chloride-containing surface complexes in the Pt/α-Al₂O₃ catalyst. However, chloride-containing entities were found on the surface of Pt/γ-Al₂O₃ and Pr/δ-Al₂O₃ catalysts. When chloride ions are removed chlorinated Pt species facilitate the sintering of Pt crystallites and in this way affect the extent of Pt dispersion. Moreover, depending upon the particular crystalline form, alumina atoms have different coordination and alumina surfaces contain varying amounts of OH groups of different nature which affect the interaction between Pt and the support.     

Co-Mo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Ni-W/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts: Potential and prospects for use in hydrotreating of light cycle oil from catalytic cracking

Со-Мо/Al₂O₃ and Ni-W/Al₂O₃ catalysts were tested in hydrotreating of light cycle oil from catalytic cracking, of the straight-run gasoil, and of their mixture under typical hydrotreating conditions used in industry. The catalysts prepared using PMo₁₂ and PW₁₂ heteropoly acids exhibit high catalytic activity. The Со-Мо/Al₂O₃ catalyst is more active in hydrodesulfurization and hydrogenation of olefin and diene hydrocarbons, whereas the Ni-W/Al₂O₃ catalysts are more active in hydrogenation of mono- and polycyclic aromatic hydrocarbons. Comparison of the quality characteristics of the hydrogenizates obtained with the requirements of the technical regulations shows that the required levels of the sulfur content and cetane number of the hydrogenizates at practically accessible process parameters can be reached for mixtures of the straight-run gasoil and light cycle oil from catalytic cracking with high content of the latter component only when the process with the Со-Мо/Al₂O₃ system and Ni-W/Al₂O₃ catalysts is performed in two steps.     

Gold catalysts supported on ZnO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for low-temperature CO oxidation

Gold catalysts with loadings ranging from 0.5 to 7.0 wt% on a ZnO/Al₂O₃ support were prepared by the deposition–precipitation method (Au/ZnO/Al₂O₃) with ammonium bicarbonate as the precipitation agent and were evaluated for performance in CO oxidation. These catalysts were characterized by inductively coupled plasma-atom emission spectrometry, temperature programmed reduction, and scanning transmission electron microscopy. The catalytic activity for CO oxidation was measured using a flow reactor under atmospheric pressure. Catalytic activity was found to be strongly dependent on the reduction property of oxygen adsorbed on the gold surface, which related to gold particle size. Higher catalytic activity was found when the gold particles had an average diameter of 3–5 nm; in this range, gold catalysts were more active than the Pt/ZnO/Al₂O₃ catalyst in CO oxidation. Au/ZnO/Al₂O₃ catalyst with small amount of ZnO is more active than Au/Al₂O₃ catalyst due to higher dispersion of gold particles.     

Effect of hydrothermal treatment on the composition and structure of Pt(IV) hydroxo complexes as model precursors of the active component in Pt/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

The influence of hydrothermal treatment conditions (temperature, duration, acidity of the medium) on the structural and chemical transformations of the complex H₂[Pt(OH)₆] was studied. The composition and structure of the resulting compounds were determined by several physicochemical methods. Thermal analysis coupled with mass spectrometry showed that, as the hydrothermal treatment temperature is raised from 25 to 120 and 150°C, the product composition in terms of empirical formulas changes as follows: PtO₂ · 4H₂O → PtO₂ · 3.5H₂O → PtO₂ · 1.5H₂O. X-ray diffraction and UV and IR spectroscopy demonstrated that the changes in the chemical composition are accompanied by the amorphization of the structure and Pt-O bond strengthening. X-ray structure determination using the radial electron density distribution method showed that polynuclear species ～10–15 Å in size with a structure similar to that of orthorhombic PtO₂ form in the complexes subjected to “hard” hydrothermal treatment (T ≥ 150°C).     

A comparative study of Ir/Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>, Pt/Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>, and Ru/Ga<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts in selective hydrogenation of crotonaldehyde

Catalytic performance of gallia-supported iridium catalysts in the reaction of selective hydrogenation of crotonaldehyde in the gas phase was studied and compared to that of platinum and ruthenium catalysts. The best catalytic properties in terms of the selectivity to crotyl alcohol are shown by 5 wt % Pt/α-Ga₂O₃ and 5 wt % Ir/α-Ga₂O₃ catalysts prepared from nonchlorine precursors: Pt(acac)₂ and Ir(acac)₃, but for the 5 wt % Pt/α-Ga₂O₃ a very high selectivity of 75% at the high conversion (ca. 60%) is observed. A high selectivity of galia-supported iridium and platinum catalysts was explained by the surface reducibility of gallium oxide leading to covering (decoration) of platinum and iridium by gallium suboxides and the promoting effect of gallium.     

Hydrogenolysis of glycerol to propanediols over heteropolyacids promoted AgCu/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Various amounts and different types of heteropolyacids promoted 5Ag15Cu/Al₂O₃ catalysts were prepared by impregnation method and analyzed through many techniques. The synthesized catalysts were evaluated for hydrogenolysis of glycerol to propanediols. The results demonstrated that heteropolyacids loading facilitated the reduction, promoted the dispersion, enhanced the acidity, and increased Broensted acid sites of the AgCu catalysts, which benefited the generation of 1,3-propanediol. Compared with phosphotungstic acid and phosphomolybdic acid, silicotungstic acid promoted AgCu catalyst had a better performance for 1,3-propanediol due to the better Cu dispersion and higher Broensted acidity. In addition, when the reaction was performed at 220 °C under 3.5 MPa for 8 h, the chosen 5Ag15Cu-10HSiW/Al₂O₃ achieved a 69.6% glycerol conversion with 35.6% 1,2-propanediol selectivity and 21.5% 1,3-propanediol selectivity.     

Comparative Study of the Oxygen Storage Capacity of Pt/M<Subscript>x</Subscript>O<Subscript>y</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Systems

The oxygen storage capacity of 1% Pt/15% M_xO_y/Al₂O₃ systems containing a rare-earth or an alkaline-earth metal oxide or TiO₂ as the oxygen-storing component was studied. Oxygen storage capacity was evaluated as the amount of C₃H₈ reacting at 400°C with oxygen that was taken up by the catalyst during oxidative treatment. The systems containing a rare-earth metal oxide or TiO₂ possess the highest oxygen storage capacity among the catalysts examined (80 and 75 µmol C₃H₈/g Cat, respectively). Of the BaO and SrO systems, the latter is of interest, although its oxygen storage capacity (∼27 µmol C₃H₈/g Cat) is somewhat lower than the oxygen storage capacity of any rare-earth metal oxide or the TiO₂ system.__________Translated from Kinetika i Kataliz, Vol. 46, No. 4, 2005, pp. 585–589.Original Russian Text Copyright © 2005 by Sinel’nikov, Tolkachev, Stakheev.     

Composition of the gas phase over Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and the enthalpies of atomization of AlO,Al<Subscript>2</Subscript>O,and Al<Subscript>2</Subscript>O<Subscript>2</Subscript>

The A1, O, AlO, A1₂O, Al₂O₂, WO₂, and WO₃, partial pressures in the vapor over Al₂O₃ in a tungsten Knudsen effusion cell between 2300 and 2600 K were derived from A1⁺, O⁺, AlO⁺, A1₂O⁺, Al₂O₂⁺, WO₂⁺, and WO₃⁺, ion intensities. The mass spectrometer was calibrated against the equilibrium constant of the WO₃(g) = WO₂(g) + O(g) reaction. Refined values of the ionization cross sections of AlO and A1₂O₂ were used in the partial pressure calculations. The enthalpies of atomization of aluminum suboxides were determined to be Δ_at H ^o(AlO, g, 0) = 510.7 ± 3.3 kJ mol⁻¹, Δ_at H ^o(Al₂O, g, 0) = 1067.2 ± 6.9 kJ mol⁻¹, and Δ_at H ^o(Al₂O₂, g, 0) = 1556.7 ± 9.9 kJ mol⁻¹.     

Genesis of the active-component precursor in the synthesis of Pt/Al2O3 catalysts: II. Synthesis of platinum hydroxo complexes on the alumina surface as precursors of the active component of Pt/Al2O3 catalysts

The thermal hydrolysis of chloroplatinate adsorbed on γ-Al₂O₃ is a possible approach to the synthesis of surface platinum hydroxo complexes as precursors to the active component of supported platinum catalysts. It is demonstrated by EXAFS and diffuse reflectance spectroscopy that the surface chloro complexes undergo deep hydrolysis under hydrothermal conditions at various processing times and temperatures. The average oxygen coordination number of platinum in these complexes is as large as 4.5. According to gradient elution data obtained using both the competitive replacement of adsorbed complex anions and variation of the charged state of the oxide surface, the resulting hydrolyzed precursor differs from the conventional chloride precursor in the nature of binding to the surface and interacts with alumina via a coordination mechanism.     

Investigation of macro-/mesoporous Re<Subscript>2</Subscript>O<Subscript>7</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts prepared by a particle-template method for butylene metathesis

Macro-/mesoporous Al₂O₃ supports were prepared by using monodisperse polystyrene (PS) microspheres as a template. The pore volume and BET surface area of the Al₂O₃ supports increased considerably with increasing amounts of the PS microspheres; further investigation showed that PS template only increased the volume of macro-pores but did not change the volume of meso-pores or micro-pores. Macro-/mesoporous Re₂O₇/Al₂O₃ metathesis catalysts were prepared through loading Re₂O₇ onto the as-prepared macro-/mesoporous Al₂O₃ supports, and their catalytic performance was tested in a fixed-bed tubular reactor using the metathesis of normal butylenes as a probe reaction. The results showed that the prepared macro-/mesoporous Re₂O₇/Al₂O₃ catalyst had high activity with consistent selectivity; propylene and pentene accounted for more than 90 wt% of the metathesis products, while the amount of ethylene plus hexane was less than 10 wt%, the majority of which was hexane. These Re₂O₇/Al₂O₃ catalysts had not only higher activity, but also longer working life span and higher tolerance to carbon residues than conventional Re₂O₇/Al₂O₃ catalysts.     

Thermal stability and surface structure of Mo/CeO<Subscript>2</Subscript> and Ce-doped Mo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

In order to explore the influence of CeO₂ on the structure and surface characteristics of molybdena, an investigation was undertaken by using N₂ adsorption (BET method), thermal analysis and in-situ diffuse reflectance infrared (DRIFT) techniques. In this work, the Mo/CeO₂ and Ce-Mo/Al₂O₃ samples were prepared by impregnation and co-precipitation methods with high Mo loadings. Combining the results one may notice that the presence of ceria led to the increase of polymerized surface Mo species so as to forming Mo-O-Ce linkages besides the formation of coupled O=Mo=O bonds indicative of polymeric MoO₃. From thermal analysis, it can be inferred that Mo/Al₂O₃ is the thermally most stable material in the temperature range used in the experiment (up to 900°C), whereas Ce-Mo/Al₂O₃ and Mo/CeO₂ samples undergo morphological modifications above 700°C resulting in lattice defects, which motivate the mobility of Mo and Ce ions and thus enhance the possibility of interaction between them. Additionally, their activity towards CO adsorption needs reduced ceria and molybdena containing coordinatively unsaturated sites (CUS), oxygen vacancies and hydroxyl groups to form various carbonate species.     

Selective oxidation of carbon monoxide in hydrogen-containing gas on CuO-CeO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts prepared by surface self-propagating thermal synthesis

The CuO-CeO₂/Al₂O₃ catalysts for the selective oxidation of CO in hydrogen-containing mixtures were prepared by surface self-propagating thermal synthesis (SSTS) with the use of cerium nitrate Ce(NO₃)₃, the ammonia complex of copper acetate [Cu(NH₃)₄](CH₃COO)₂, and citric acid C₆H₈O₇ as a fuel additive. The effect of the C₆H₈O₇/Ce(NO₃)₃ molar ratio on the catalyst activity and selectivity for oxygen was studied. The catalyst samples were studied by X-ray diffraction (XRD) analysis, temperature-programmed reduction (TPR-H₂), IR spectroscopy of adsorbed CO, and transmission electron microscopy (TEM). It was found that an increase in the C₆H₈O₇/Ce(NO₃)₃ ratio resulted in an increase in the degree of dispersion of the resulting CeO₂ phase. The greatest amount of dispersed CuO particles, which are responsible for catalytic activity in the oxidation of CO, was formed at C₆H₈O₇/Ce(NO₃)₃ = 1.     

Studies on the synthesis of higher alcohol over modified Cu/ZnO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst

Higher alcohol has been considered as a potential fuel additive. Higher alcohol, including C₂–C₄ alcohol was synthesized by catalytic conversion of syngas (with a ratio of CO/H₂?=?1) derived from natural gas over modified Cu/ZnO/Al₂O₃ catalyst. Modified Cu/ZnO/Al₂O₃ catalysts promoted by alkali metal (Li) for higher alcohol synthesis (HAS) were prepared at different pH (6, 6.5, 7, 8, and 9) by co-precipitation to control Cu surface area and characterized by N₂ physisorption, XRD, SEM, H₂-TPR and TPD. The HAS reaction was carried out under a pressure of 45 bar, GHSV of 4000 h^?1, ratio of H₂/CO?=?1, and temperature ranges of 240 and 280 °C. It was found that the malachite phase of copper causes the size of copper to be small, which is suitable for methanol synthesis. Methanol and HAS share a common catalytic active site and intermediate. It was also found that the productivity to higher alcohol was correlated with Cu surface area.     

Effect of cerium dioxide on the properties of monolithic CuO-ZnO-CeO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/cordierite catalysts in methanol decomposition

Cerium dioxide as a component of CuO-ZnO-CeO₂/Al₂O₃/cordierite catalysts stabilizes their action in the decomposition of methanol by preventing carbon deposition on the surface and facilitating hydrogen formation with selectivity and yield in the range 85–96%. The optimal indices for this reaction are obtained for a CeO₂-CuO/Al₂O₃/cordierite sample prepared using an ammonium precursor for cerium, (NH₄)₂Ce(NO₃)₆. This catalyst displays enhanced reductive capacity relative to the analogous CeO₂-CuO composition prepared using Ce(NO₃)₃·6H₂O.     

Sonochemical synthesis of vanadium complex nano-particles: a new precursor for preparation and evaluation of V<Subscript>2</Subscript>O<Subscript>5</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nano-catalyst in selective oxidation of methanol to methylal

In this study, an ionic complex of V(V) was synthesized by using ultrasonic method, and it was used as a precursor for production of a new catalyst for selective preparation of methylal or dimethoxymethane (DMM). By reaction between an ionic ligand [pyda.H₂]²⁺[pydc]^2? (LH₂), (pyda.H₂ = 2,6-pyridine diammonium and pydc = 2,6-pyridinedicarboxylate) and ammonium vanadate, the five coordinated V(V) complex, [pyda.H][V(pydc)O₂], {2,6- diaminopyridinum 2,6-pyridinedicarboxylatodioxovanadate(V)}, VLH₂ was synthesized. The prepared complex VLH₂ was characterized by SEM, thermal analysis TGA/DTA, FT-IR spectroscopy and X-ray diffraction studies. The results showed that the yield of the reaction was increased up to 64%. The average particle sizes of the obtained complex VLH₂ were about 50–60 nm. Also, the nano-catalyst of V₂O₅/Al₂O₃ was synthesized by impregnation method and was prepared as a nano-catalyst with average particles sizes of 50–60 nm, and its characterization was performed by XRD, EDX and SEM methods. Finally, the prepared catalyst was used to converting of methanol to methylal at different process conditions.     

Oxidative desulfurization of thiophene derivatives with H<Subscript>2</Subscript>O<Subscript>2</Subscript> in the presence of catalysts based on MoO<Subscript>3</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> under mild conditions

The catalysts based on MoO₃/Al₂O₃ were synthesized and tested using aqueous hydrogen peroxide as the oxidant in the oxidative desulfurization of thiophene, benzothiophene (BT) and dibenzothiophene (DBT) into the corresponding sulfones. Among catalysts tested, 15%(MoO₃–WO₃)/Al₂O₃ prepared by a conventional impregnation method was considerably active for the oxidation of thiophene, BT and DBT, which could achieve higher than 99.2% conversions at lower reaction temperature (≤338 K). The use of hexadecyltrimethyl ammonium bromide as the phase-transfer reagent in small amounts could promote the reaction efficiently.