一种高容量的层状Co-MOF基超级电容器电极材料

通过简单的溶剂热反应合成了一种钴基层状MOF（[Co（4,4''-bpy）（tfbdc）（H₂O）₂],Co-BTH,4,4''-bpy=4,4''-联吡啶,H₂tfbdc=四氟对苯二甲酸）,并考察了其作为超级电容器电极材料的性能。研究结果表明：Co-BTH电极具有良好的赝电容性能,包含高比电容和较好的倍率性能。在1 A·g^-1电流密度下和1 mol·L^-1 KOH溶液中,其比电容最大可达2 316 F·g^-1。在2 A·g^-1的电流密度下,循环1 000次后,电极的比电容仍然还有847 F·g^-1。良好的赝电容性能与Co-BTH的层状结构和小尺寸的纳米片有关。     

壳聚糖基多孔碳材料的制备及其超级电容性能

以胶态SiO₂纳米粒子为模板,壳聚糖为碳源,ZnCl2为活化剂,制备了具有不同比表面积和孔体积的氮掺杂介孔碳。采用多种表征手段对碳材料的微观形貌、比表面积和孔道结构进行了表征,探究了壳聚糖与SiO₂纳米粒子的比例以及ZnCl2活化剂对碳材料孔体积和比表面积的影响。结果表明,在未使用活化剂时碳材料(CSi-1.75)的孔体积高达4.53 cm³·g^-1,但其比表面积最小(729 m²·g^-1);使用ZnCl₂作为活化剂制备的碳材料(CSi-1.75-Zn)比表面积为1032 m²·g^-1,但其孔体积下降到1.99 cm³·g^-1,且具有最多的吡啶氮和吡咯氮。在以6.0 mol·L^-1 KOH为电解液的三电极体系中,当电流密度为0.5 A·g^-1时,CSi-1.75-Zn的比电容为344 F·g^-1,而CSi-1.75的比电容仅为255 F·g^-1。这表明碳材料的比表面积对超级电容性能影响最大,而孔体积影响较小。电容贡献分析结果表明,相对于CSi-1.75,CSi-1.75-Zn的双电层电容和赝电容都得到了提高,这表明更大的比表面积和更多的吡啶氮和吡咯氮有利于提高碳材料的超级电容性能。     

惰性盐辅助合成介孔石墨化碳片及其电容性能

以惰性盐KCl为模板、硝酸镍为金属催化剂镍源、葡萄糖为碳源,通过碳化处理制备了介孔石墨化碳片。利用扫描电子显微镜、透射电子显微镜、X-射线衍射仪和比表面测试仪对介孔石墨化碳片进行了表征。探讨了碳片形成的机理,采用三电极测试体系研究了介孔石墨化碳片电极材料的电化学性能。结果表明,10gKCl制备的碳片比表面积最大（989m²·g^-1）,在6mol·L^-1KOH电解液中,当电流密度为0.5A·g^-1时,比电容达到180F·g^-1;当电流密度达到10A·g^-1时,比电容维持在148F·g^-1,显示了电极具有较好的倍率性能;在10A·g^-1条件下,2000次循环充放电测试后电容没有发生衰减,展示了在超级电容器方面的应用潜力。     

超高比表面积氮掺杂多孔碳材料的制备及其超级电容性能

以蔗糖为碳源,尿素为氮源,草酸钾为活化剂,通过简单的研磨和高温碳化制备了具有超高比表面积(大于3 000 m²·g^-1)的氮掺杂多孔碳材料。采用多种手段对多孔碳材料的微观形貌、比表面积、孔结构和表面氮物种进行了表征,探究了不同温度下草酸钾和尿素对碳材料的比表面积、氮含量和超级电容性能的影响。结果表明,仅使用草酸钾作为活化剂制备的碳材料KC-800 的比表面积为 1 114 m2·g^-1,而同时使用草酸钾和尿素制备的样品 KNC-800 的比表面积高达 3 033 m²·g^-1。在以 6.0mol·L^-1 KOH 为电解液的三电极体系中,当电流密度为 0.5 A·g^-1时,KNC-800 的比电容为 405 F·g^-1,而 KC-800 的比电容仅为248 F·g^-1。这表明草酸钾和尿素的加入显著提高了多孔碳材料的比表面积和超级电容性能。电容贡献分析表明,KNC-800的双电层电容值和赝电容值均高于KC-800。KNC-800在电流密度为0.5 A·g^-1时经过10 000次循环后仍能保持98.3%的初始比电容,表现出优异的循环性能。     

木糖-软模板水热法制备硼掺杂分级多孔炭球及其电化学性能

以D-木糖为炭源,月桂酸钠为模板剂,硼酸为掺杂剂,通过水热炭化方法制得硼掺杂分级多孔炭球（BPC_S）。通过扫描电子显微镜（SEM）、透射电子显微镜（TEM）、N₂吸附-脱附测试、X射线光电子能谱（XPS）、顺磁共振波谱（EPR）、傅里叶红外光谱（FT-IR）、拉曼光谱（Raman）、X射线粉末衍射（XRD）、热重（TG）分析对样品进行表征。结果表明：月桂酸钠作为介孔造孔剂的同时,通过与D-木糖间的氢键作用使有机-有机自组装过程自发进行并形成窄尺寸分布（2~5 μm）规整炭球;硼酸在水热中催化炭源脱水降解,并以BC₃、BCO₂和BC₂O的形式掺杂在炭球上,掺硼后炭球与水表面接触角降低,润湿性提高。经CO₂活化、月桂酸钠高温分解以及胶质炭球的堆积分别产生微孔（0.5~1.2 nm）、介孔（3.14~35.00 nm）和大孔（60~146 nm）并形成分级结构。当硼酸加入量为0.927 5 g时多孔炭球（BPC_S-1）的电化学性能最佳,在6 mol·L^-1 KOH三电极体系中电流密度为0.5 A·g^-1时,比电容达287.12 F·g^-1;两电极体系中电流密度为0.5 A·g^-1时比电容达151.34 F·g^-1,能量密度达5.3 Wh·kg^-1;电流密度为5 A·g^-1时进行1 000次充放电循环,电容保持率仍达96.43%。     

Zn掺杂Co9S8纳米材料的制备及其在超级电容器和电催化析氢中的应用

采用原位溶剂热生长法设计合成了锌掺杂Co₉S₈纳米颗粒。各种表征技术和性能测试结果表明：锌掺杂Co₉S₈纳米颗粒的孔尺寸为18 nm,比表面积为23 m²·g^-1;同时微量的锌掺杂显著增强了Co₉S₈的电催化析氢（HER）活性及电容器性能。在HER性能测试中,当电流密度为10 mA·cm^-2时电位为-361 mV,电流密度最高可达38.26 mA·cm^-2,且具有优异的循环稳定性。同时在电容器性能测试中具有较高的比电容,当电流密度为1 A·g^-1时,质量比电容和面积比电容分别为235.48 F·g^-1和812.4 mF·cm^-2。     

同构MOFs复合氧化石墨烯电极材料构筑高性能超级电容器

在水热条件下一步自组装合成系列同构X-MOF （X₆O （TATB）₄（H⁺）₂·（H₂O）₈·（DMF）₂,X=Zn、Co、Ni; H₃TATB=4,4'',4″-s-triazine-2,4,6-triyl-tribenzoic acid; DMF=N,N-二甲基甲酰胺）和氧化石墨烯（GO）的复合材料（X-MOF@GO）,并探究其作为超级电容器电极材料的电化学性能。通过X射线粉末衍射、X射线光电子能谱和扫描电子显微镜测试证明GO和MOFs复合成功。其中,性能最优的Ni-MOFs@1.5GO （GO的添加量为1.5 mL）的比电容高达694.8 F·g^-1（0.5 A·g^-1）,约是Ni-MOF的2倍。电化学测试结果表明：复合材料X-MOF@1.0GO较其原MOF表现出更大的比电容和更好的倍率性能。在3.5 A·g^-1的电流密度下,1 000次循环充放电后,Ni-MOFs@1.0GO仍保持初始比电容量的81.2%。与活性炭（AC）组装的非对称超级电容器Ni-MOF@1.5GO//AC的性能最优,其功率密度为754.3 W·kg^-1时,能量密度为15.4 Wh·kg^-1,且循环3 000次后比电容保持率约为70.0%,显示出较长的循环寿命。     

表面官能团化增强碳纳米笼超级电容器性能

以具有多级孔结构、高比表面积、良好导电性等特征的碳纳米笼（CNCs）为前体,采用硝酸氧化法在CNCs表面引入含氧官能团。以CNCs为超级电容器电极材料,在相同电流密度下,官能团化样品的比电容显著高于纯CNCs;在1A·g^-1下比电容最高可达到255F·g^-1,比纯CNCs的188F·g^-1增加了34%,这表明表面含氧官能团化能够显著提高CNCs的超级电容器比电容。在100A·g^-1的大电流密度下,硝酸氧化后CNCs的比电容保持在111~167F·g^-1,表明具有良好的耐大电流充放电性能。在10A·g^-1的电流密度下循环10000圈后,CNC-6M样品的比电容由196F·g^-1下降到176F·g^-1,样品的比电容仍保留90%,具有良好的循环稳定性。表面含氧官能团化CNCs所表现出的这种优异的超级电容器性能归因于CNCs的多尺度分级孔结构、高比表面积、良好的导电性、表面亲水性含氧官能团化带来的浸润性提高和引入的赝电容。     

用于高性能超级电容器的金属有机骨架衍生Co(OH)2/C-N@GP纳米复合材料

本文报道一种制备β-Co（OH）₂/氮掺杂碳石墨烯纳米复合材料（Co（OH）₂/C-N@GP）的方法。首先,我们通过在含羧基的聚苯乙烯（PS）乙醇分散体中使Co（NO₃）₂·6H₂O与2-甲基咪唑反应,合成了ZIF-67/聚苯乙烯的复合材料。然后将ZIF-67/聚苯乙烯复合材料高温碳化,同时与硫代乙酰胺和石墨烯反应生成Co（SO₄）₂/C-N@GP。最后,Co（SO₄）₂/C-N@GP在KOH水溶液中浸泡以获得Co（OH）₂/C-N@GP纳米复合材料。所制备的Co（OH）₂/C-N@GP的扫描电镜图显示尺寸为10~20 nm的Co（OH）₂很好地分散在石墨烯上。电化学分析表明Co（OH）₂/C-N作为超级电容器的电极材料表现出典型的法拉第电荷转移行为,并且当石墨烯存在时,其比电容可显著增强。在2 mol·L^-1 KOH中,Co（OH）₂/C-N@GP在2 A·g^-1下表现出985.4 F·g^-1的高比电容,1 000次循环后的比电容保持率为76.6%。     

泡沫镍负载NiMoO4/NiMoS4复合材料的制备及其电化学性能

以泡沫镍作为基底，采用水热法原位生长出具有片状结构的NiMoO₄活性材料，然后通过水热硫化制备出NiMoO₄/NiMoS₄复合材料，研究了水热时间和硫脲添加量对样品形貌和电化学性能的影响。电化学结果表明，NiMoO₄/NiMoS₄电极在电流密度为 1 A·g^-1时，比电容为 1 560.7 F·g^-1，在电流密度为 40 A·g^-1时循环 2 000次后，比电容仍为初始比电容的 76.7%。将 NiMoO₄/NiMoS₄电极材料与活性炭(AC)分别作为正、负极组装的非对称超级电容器(ASC)在 400 W·kg^-1的功率密度下可提供 29.0 Wh·kg^-1的能量密度。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.