Microwave-assisted covalent sidewall functionalization of multiwalled carbon nanotubes

Thermal cycloaddition of 1,3-dipolar azomethine ylides to the sidewalls of multiwalled carbon nanotubes (MWNTs) has been used to prepare MWNTs that contain 2-methylenethiol-4-(4-octadecyloxyphenyl) (4), N-octyl-2-(4-octadecyloxyphenyl) (5) or 2-(4-octadecyloxyphenyl)pyrrolidine (6) units. All these contain the 4-octadecyloxyphenyl substituent that acts as a solubilizing group. Microwave (MiW)-assisted heating was found to be highly efficient for soluble MWNTs, for which the amount of added groups after only 2 h of MiW heating at 200 degrees C, determined by using thermogravimetric analysis, was found to be in the same range as that obtained after 100-120 h of conventional heating of soluble and insoluble MWNTs. Solubility is a key feature for a successful MiW-heated reaction; MWNTs insoluble in the reaction medium yielded considerably less addends in the MiW-heated reactions than in the conventionally heated reaction. The location and even distribution of the pyrrolidine units over the outermost layer of the MWNTs was verified by transmission electron microscopy analysis of 4 that had been treated with gold nanoparticles and thoroughly washed to remove gold particles adsorbed on nonfunctionalized parts of the MWNTs.     

Optimizing functionalization of multiwalled carbon nanotubes using sodium lignosulfonate

Multiwalled carbon nanotubes (MWCNTs) were functionalized with sodium lignosulfonate (SLS) at various SLS/MWCNT ratios, and the solubility of the functionalized MWCNTs was examined using ultraviolet-visible (UV-Vis) spectroscopy. Then, the effects of SLS on the dispersion and conductivity of MWCNTs were investigated. A calibration curve was constructed to measure the concentration of MWCNTs in water using the absorbance measured from UV-Vis spectroscopy. Using the curve, the change in the functionalized MWCNT concentration was investigated as a function of time. The results showed that the solubility of the MWCNTs did not increase significantly with further increases in SLS after the appropriate amount of SLS was employed. Excessive use of SLS rather decreased the conductivity of functionalized MWNTs. Also, the solubility of MWCNTs was influenced by dispersing method even when the same amount of SLS was used. Our method could functionalize the MWCNTs with a small amount of SLS, and the solution could remain stable for lengthy periods of time.     

Controlled functionalization of multiwalled carbon nanotubes by in situ atom transfer radical polymerization

The in situ ATRP (atom transfer radical polymerization) "grafting from" approach was successfully applied to graft poly(methyl methacrylate) (PMMA) onto the convex surfaces of multiwalled carbon nanotubes (MWNT). The thickness of the coated polymer layers can be conveniently controlled by the feed ratio of MMA to preliminarily functionalized MWNT (MWNT-Br). The resulting MWNT-based polymer brushes were characterized and confirmed with FTIR, 1H NMR, SEM, TEM, and TGA. Moreover, the approach has been extended to the copolymerization system, affording novel hybrid core-shell nanoobjects with MWNT as the core and amphiphilic poly(methyl methacrylate)-block-poly(hydroxyethyl methacrylate) (PMMA-b-PHEMA) as the shell. The approach presented here may open an avenue for exploring and preparing novel carbon nanotubes-based nanomaterials and molecular devices with tailor-made structure, architecture, and properties.     

Noncovalent functionalization of multiwalled carbon nanotubes: application in hybrid nanostructures

We developed a reproducible, noncovalent strategy to functionalize multiwalled carbon nanotubes (MWNTs) via embedding nanotubes in polysiloxane shells. (3-Aminopropyl)triethoxysilane molecules adsorbed to the nanotube surfaces via hydrophobic interactions are polymerized simply by acid catalysis and form a thin polysiloxane layer. On the basis of the embedded MWNTs, negatively charged gold nanoparticles are anchored to the nanotube surfaces via electrostatic interactions between the protonated amino groups and the gold nanoparticles. Furthermore, these gold nanoparticles can further grow and magnify along the nanotubes through heating in HAuCl4 aqueous solution at 100 degrees C; as a result these nanoparticles are joined to form continuous gold nanowires with MWNTs acting as templates.     

Modification of multiwalled carbon nanotubes by carboxy groups and determination of the degree of functionalization

Multiwalled carbon nanotubes were modified by carboxy groups. Four independent methods for the determination of the degree of functionalization of the surface were proposed: ¹³C NMR spectroscopy, thermogravimetry, titrimetry, and fluorimetry. The first two methods show the total content of carboxy groups in the sample, and the latter two methods give information about the content of the surface groups only. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2, pp. 291–295, February, 2008.     

Controlled chemical functionalization of multiwalled carbon nanotubes by kiloelectronvolt argon ion treatment and air exposure

The chemical and morphological modifications of multiwalled carbon nanotubes (MWCNTs), by 2 keV Ar(+) treatment, have been followed by field emission scanning (FESEM) and high-resolution transmission (HRTEM) electron microscopies and by X-ray photoelectron (XPS) and Raman spectroscopies. Morphological changes were followed, both in situ and on subsequent air exposure, and the data indicate that free radical defects, initially produced under low Ar(+) treatment doses ( approximately 10(13) ions/cm(2)), act as the nuclei for the formation of localized asperities that form along the walls of the CNTs. Continued treatment results in their stublike elongation that continues with further treatment, forming extensions under heavy treatment doses. The chemical changes that occur, on reaction with air, reveal that the defects initially created are secondary C atoms, formed when a single bond breaks; further treatment breaks an additional bond to form primary C atoms; free radical fragments, lost when the third bond breaks, condense on the free radical defects to form the asperities. The extent of primary and secondary C atoms, and thus their functionalization on air exposure, may be controlled by the extent of treatment, offering a method for the controlled surface functionalization of CNTs by low-energy Ar(+) treatment.     

Aqueous noncovalent functionalization and controlled near-surface carbon doping of multiwalled boron nitride nanotubes

Noncovalent functionalization of boron nitride nanotubes (BNNTs) in aqueous solution was achieved by means of pi-stacking of an anionic perylene derivative, through which carboxylate-functionalized BNNTs were prepared for the first time. Starting from the functionalized nanotubes, an innovative methodology was designed and demonstrated for the controlled near-surface carbon doping of BNNTs. As a result of such delicate doping, novel B-C-N/BN coaxial nanotubes have been fabricated, and their p-type semiconducting behaviors were elucidated through gate-dependent transport measurements.     

Controlled functionalization of multiwalled carbon nanotubes with various molecular-weight poly(L-lactic acid)

Multiwalled carbon nanotubes (MWNT) were functionalized with poly(L-lactic acid) (PLLA) with different molecular weights using a "grafting to" technique. The oxidized MWNT (MWNT-COOH) were converted to the acyl-chloride-functionalized MWNT (MWNT-COCl) by treating them with thionyl chloride (SOCl2) and reacting them with PLLA to prepare the MWNT-g-PLLA. FTIR and Raman spectroscopy revealed that the PLLA was covalently attached to the MWNT, and the weight gain due to the functionalization was determined by thermogravimetric analyses (TGA). The Raman signals of the MWNT were greatly weakened as a result of the PLLA grafting. The morphology of the grafted PLLA was examined by using SEM and TEM. The amount of grafted PLLA depended on the molecular weight of the PLLA. The PLLA coated on the MWNT became thicker and more uniform with increasing PLLA molecular weight from 1000 to 3000. However, the amount of grafted PLLA became lower when the molecular weight of PLLA was further increased to 11,000 and 15,000, and the PLLA attached to the MWNT showed a squid leglike morphology forming blobs and leaving much of the MWNT surface bare.     

Covalent functionalization of multiwalled carbon nanotubes with poly(styrene-co-acrylonitrile) by reactive melt blending

A small amount of cyano groups in poly(styrene-co-acrylonitrile) (SAN) was converted to oxazoline groups through reaction with 2-aminoethanol. Reactive melt blending of oxazoline-containing SAN and acidified multiwalled carbon nanotubes (MWCNTs) leads to the grafting of polymer chains onto MWCNTs arising from reactions between oxazoline and carboxylic acid groups. Spectroscopic, thermal and microscopic techniques confirmed the successful grafting of SAN onto MWCNTs. This method is comparatively simpler and greener than a previously reported method, and can be adopted to graft other acrylonitrile-containing polymers onto MWCNTs.     

Novel UV initiator for functionalization of multiwalled carbon nanotubes by atom transfer radical polymerization applied on two different grades of nanotubes

A novel nonoxidative method for preparation of functionalized multiwalled carbon nanotubes (MWCNT) has been developed based on a UV sensitive initiator for atom transfer radical polymerization (ATRP). The method has been investigated with respect to ligands and polymerization time for the preparation of polystyrene functionalized MWCNT. It was found that pentamethyldiethylenetriamine (PMDETA) gave superior results with higher loading in shorter polymerization time. A comparative study of the method applied on two different grades of nonoxidized MWCNT has been performed, illustrating large differences in reactivity and polymer loading, underlining the importance of the choice of MWCNT starting material. In addition to styrene, also poly(ethylene glycol) methacrylate (PEGMA) was shown to polymerize from the surface of the MWCNT. Finally, initial results from composites of polystyrene or polyphenylenesulfide are presented. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Solvent-free functionalization of carbon nanotubes

A fundamentally new single-walled and multiwalled carbon nanotube sidewall functionalization technique has been developed in which solvent is not required and the reaction times are greatly shortened (1 h at 60 degrees C). Exploiting the long linear dimension of the nanotube ropes by macroscopic mechanical deformation, reactive sites are generated merely by mechanically deforming the tubes using a stir bar. This approach eliminates the need for large volumes of solvent ( approximately 2 L/g), which were formerly considered essential due to the insolubility of carbon nanotubes. Using a series of 4-substituted anilines and a nitrite, the aryl diazonium intermediates were generated in situ and permitted to react with the tubes. Raman, IR, and UV spectroscopies, coupled with thermogravimetric analyses and solubility studies, support the assignments.     

Organic functionalization of carbon nanotubes

A very general and versatile method for functionalizing different types of carbon nanotubes is described, using the 1,3-dipolar cycloaddition of azomethine ylides. Approximately one organic group per 100 carbon atoms of the nanotube is introduced, to yield remakably soluble bundles of nanotubes, as seen in transmission electron micrographs. The solubilization of the nanotubes generates a novel, interesting class of materials, which combines the properties of the nanotubes and the organic moiety, thus offering new opportunities for applications in materials science, including the preparation of nanocomposites.     

Enzymatic degradation of multiwalled carbon nanotubes

Because of their unique properties, carbon nanotubes and, in particular, multiwalled carbon nanotubes (MWNTs) have been used for the development of advanced composite and catalyst materials. Despite their growing commercial applications and increased production, the potential environmental and toxicological impacts of MWNTs are not fully understood; however, many reports suggest that they may be toxic. Therefore, a need exists to develop protocols for effective and safe degradation of MWNTs. In this article, we investigated the effect of chemical functionalization of MWNTs on their enzymatic degradation with horseradish peroxidase (HRP) and hydrogen peroxide (H(2)O(2)). We investigated HRP/H(2)O(2) degradation of purified, oxidized, and nitrogen-doped MWNTs and proposed a layer-by-layer degradation mechanism of nanotubes facilitated by side wall defects. These results provide a better understanding of the interaction between HRP and carbon nanotubes and suggest an eco-friendly way of mitigating the environmental impact of nanotubes.     

Fast functionalization of multi-walled carbon nanotubes by an atmospheric pressure plasma jet

The afterglow of an atmospheric pressure plasma has been used for the fast oxidative functionalization of multi-walled carbon nanotubes (MWCNTs). Scanning electron microscopy and Raman spectroscopy demonstrate that the MWCNT morphology is mostly preserved when the MWCNTs are dispersed in a solvent and injected as a spray into the plasma. Contact angle measurements show that this approach enhances the wettability of MWCNTs and reduces their sedimentation in an aqueous dispersion. X-ray photoelectron spectroscopy, IR spectroscopy, and electrokinetic measurements show that oxygen plasma incorporates about 6.6 at.% of oxygen and creates mainly hydroxyl and carboxyl functional groups on the MWCNT surface. The typical effective treatment time is estimated to be in the range of milliseconds. The approach is ideally suited for combination with the industrial gas phase CVD synthesis of MWCNTs.     

Electro-oxidation of amino-functionalized multiwalled carbon nanotubes

We report the electrochemistry of amino-functionalized multiwalled carbon nanotubes (MWCNTs-NH₂) in the pH range from 0.3 to 6.4 using quantitative cyclic voltammetry (CV) and single entity electrochemistry measurements, making comparison with non-functionalized MWCNTs. CV showed the latter to both catalyze the solvent (water) decomposition and to undergo irreversible electro-oxidation forming oxygen containing surface functionality. The MWCNTs-NH₂ additionally undergo an irreversible oxidation to an extent which is dependent on the pH of the solution, reflecting the variable amount of deprotonated amino groups present as a function of pH. Nano-impact experiments conducted at the single particle level confirmed the oxidation of both types of MWCNTs, showing agreement with the CV. The pK_a of the amino groups in MWCNTs was determined via both electrochemical methods giving consistent values of ca. 2.5.

A new and generic approach to the study of the oxidation of different forms of CNTs is found by using quantitative single entity and ensemble electrochemistry measurements.     

Characterization of an assortment of commercially available multiwalled carbon nanotubes

The objective of this study was to characterize an assortment of as received, commercially available, non-functionalized multiwalled carbon nanotubes (MWCNT) samples (n?=?24) using thermogravimetric analysis, energy dispersive X-ray fluorescence spectrometry, high-resolution transmission electron microscopy and scanning electron microscopy. Each sample was assigned to one of six types based on nominal length and diameter. Some of the samples from the product assortment exhibited significant differences in purity and morphology from their nominal values. Variability in the physicochemical properties of MWCNTs may be a significant factor in why many toxicological investigations have findings that are difficult to reproduce. Therefore, it is strongly recommended that investigators studying these materials present characterization information in addition to providing their source.

Sonochemical oxidation of multiwalled carbon nanotubes

Functionalization of carbon nanotubes (CNTs) is important for enhancing deposition of metal nanoparticles in the fabrication of supported catalysts. A facile approach for oxidizing CNTs is presented using a sonochemical method to promote the density of surface functional groups. This was successfully employed in a previous study [J. Phys. Chem. B 2004, 108, 19255] to prepare highly dispersed, high-loading Pt nanoparticles on CNTs as fuel cell catalysts. X-ray photoelectron spectroscopy (XPS), transmission electron microscopy, cyclic voltammetry, and settling speeds were used to characterize the degree of surface functionalization and coverage. The sonochemical method effectively functionalized the CNTs. A mixture of -C-O-/-C=O and -COO- was observed along with evidence for weakly bound CO at longer treatment times. The integrated XPS C 1s core level peak area ratios of the oxidized-to-graphitic C oxidation states, as well as the atom % oxygen from the O 1s level, showed an increase in peak intensity (attributed to -CO(x)()) with increased sonication times from 1 to 8 h; the increase in C surface oxidation correlated well with the measured atom %. Most of the CNT surface oxidation occurred between 1 and 2 h. The sonochemically treated CNTs were also studied by cyclic voltammetry and settling experiments, and the results were consistent with the XPS observations.     

Covalent surface functionalization of multiwalled carbon nanotubes through bergman cyclization of enediyne‐containing dendrimers

A method for covalent functionalization of multiwalled carbon nanotubes (MWCNTs) was developed using the free radicals generated through Bergman cyclization of enediyne‐containing compounds. Four enediyne‐bearing Frechet type dendrimers were synthesized in good quantities and characterized. Then, the enediyne‐containing molecules were reacted with MWCNTs in N‐methyl‐2‐pyrrolidinone at 206 °C under nitrogen. The structure and morphology of the resulting products were characterized by thermogravimetric analysis, ultraviolet–visible spectroscopy, Fourier transform infrared spectroscopy, Raman spectroscopy, and transmission electron microscopy. The dendrimer‐functionalized MWCNTs showed good solubility/dispersibility in common organic solvents and polymer solutions. They were used in the formation of polymer composites through electrospinning with polycaprolactone. The results confirmed the surface functionalization of MWCNTs. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Functionalization of multiwalled carbon nanotubes by mild aqueous sonication

Sonication has been widely used in the dispersal of carbon nanotubes (CNTs) in various liquids as well as in their functionalization in aqueous acids. Here, for the first time, we study the sonication of multiwalled CNTs (MWCNTs) in deionized water. Our results indicate an improvement in the aqueous dispersal of MWCNTs as well as an increase in their adhesive interaction with Au substrates. Field emission scanning electron and high-resolution transmission electron microscopies as well as X-ray photoelectron, photoacoustic Fourier transform IR, and Raman spectroscopies have shown this to be due to the production of low concentrations of O-containing functionalizations (alcohol, carbonyl, acid, with the total O concentration being approximately 2%), without damaging the basic CNT structure; this production of functional groups is mirrored by the disappearance of -CH(n) groups existing on the pristine CNTs. These new functional groups are capable of hydrogen bonding, which plays an important role in their aqueous dispersal and enhanced substrate interactions.