Competitive Occupying of Fe~(3+) and Co~(3+) Ions into the Lattice B-Sites of Perovskite Crystalline Structure

Perovskite-type oxide has a general formula ABO_3. Both the lattice A- and lattice B-sites can be occupied by two kinds of metallic ions, forming substituted perovskites such as La_(1-x)Sr_xCoO_3-d and LaFe_xCo_(1-x)O_3. In the present work, we aim to investigate competitive occupying of Fe~(3+) and Co~(3+) ions into the lattice B-sites of perovskite LaFe_xCo_(1-x)O_3 formed under the condition of excess feeding of Fe~(3+) and Co~(2+) ions relative to the La~(3+) ions. For this purpose, standard curve of normalized cell volumes(NCVs) of a defined series of perovskites LaFe_xCo_(1-x)O_3 versus the x values was plotted. Lattice occupancy of Fe~(3+) ions at the B-sites of the perovskite LaFe_xCo_(1-x)O_3 was then determined from the standard curve. It is proved that Fe~(3+) ions were capable of occupying preferentially into the lattice B-sites of the perovskite crystalline structure.     

六氰合铁酸铜钴薄膜修饰铂电极的电化学、XRD及XPS研究

采用循环伏安法在铂电极上电聚合了六氰合铁酸铜钴薄膜,并用电化学、XRD 和XPS对该薄膜进行了表征。研究表明此薄膜属于取代型的多核六氰合铁酸盐,由 Cu~(2+),Co~(2+)和Fe~(2+)共同占据晶格格点。通过改变Cu~(2+),Co~(2+)和 Fe~(3+)在沉积液中的比例可以改变聚合膜的性质。随沉积液中Cu~(2+)含量的增加 ,聚合膜中铜的含量相应增加而晶格常数则逐渐减小,但保持着面心立方的晶格对 称性。当沉积液中Cu~(2+):Co~(2+):Fe~(3+) = 1:1:2时,得到的聚合膜具有比较 典型的性质,该薄膜修饰的铂电极在pH 4～10之间均能保持着稳定的电化学响应。 其对一价阳离子的选择性顺序为K~+ > Li~+ > Na~+ > NH_4~+,与单组分的六氰铁 酸酮和六氰合铁酸钴都存在着较大的差别。XPS实验表明氧化态薄膜中铁元素以Fe (III)存在,并且在X射线的照射下很快转化为Fe(II)。     

钙钛矿型甲醇水蒸气重整制氢催化材料的研究

采用溶胶凝胶法合成了钙钛矿复合氧化物,负载氧化铜后得钙钛矿负载型催化材料,通过XRD(X射线衍射分析)、BET(比表面积测试)、H2-TPR(程序升温还原分析)、XPS(X射线光电子能谱)等手段对催化材料进行了表征,考察了不同种类钙钛矿负载纳米铜催化材料的结构、性质对甲醇水蒸气重整制氢性能的影响.结果显示,钙钛矿负载纳...     

CaO/MgO负载的钙钛矿型氧化物用于甲烷化学链蒸汽重整

甲烷化学链蒸汽重整(Chemical-looping steam methane reforming,CL-SMR)是基于化学链燃烧的概念而提出的一种新颖的技术。在重整反应器中,甲烷与载氧体中的晶格氧发生部分氧化反应生成合成气(H₂/CO物质的量比为2.0),还原后的载氧体进入到水蒸气反应器中,与水蒸气反应恢复晶格氧的同时生成H₂。以钙钛矿型氧化物LaFeO₃为载氧体用于甲烷化学链蒸气重整过程,同时通过碱金属CaO和MgO对LaFeO₃进行负载,以增大载氧体的比表面积、热稳定性和抗积炭能力。通过X射线衍射(XRD)、H₂程序升温还原(H₂-TPR)、BET比表面积分析(BET)和X光电子能谱(XPS)对载氧体进行表征。结果表明,三种载氧体均表现出较高的反应活性和合成气选择性,循环后仍能保持钙钛矿的结构。从反应性能、选择性和抗积炭能力等方面综合考虑,LaFeO₃-CaO的效果最好,五次循环后具有很好的再生性。     

合成气制乙醇的铑基催化剂中助剂铁,锂的作用本质研究

催化活性测试表明,助剂Fe具有显著提高乙醇生成选择性及铑催化活性的双重作用;助剂Li具有显著提高乙醇选择性的作用,对铑催化活性影响不大。基于H_2/D_2同位素效应结果及CO化学吸附、IR、XRD、XPS等的表征结果,认为助剂Fe经活化处理后大部分与Rh形成RhFe合金,使Rh分散度显著提高,从而提高了乙醇的选择性;Rh分散度的提高以及小部分以Fe~(2+)(Fe~(3+))形式存在的助剂Fe促进甲酰基的生成及随后的氢解断C-O键反应是助剂Fe促使铑催化活性提高的两个因素。Li的主要作用在于通过与C_2含氧中间体乙烯酮氧端的弱亲合作用,促进了乙醇前驱体的生成,从而使乙醇生成选择性提高。     

无气相氧条件下La0.8Sr0.2Fe0.9Co0.1O3钙钛矿氧化物的氧物种直接氧化甲烷

以La0.8Sr0.2Fe0.9CO0.1O3钙钛矿氧化物作氧载体,采用连续流动反应和连续顺序Redox反应考察了氧物种氧化甲烷的反应性能.结果表明,连续流动反应中La0.8Sr0.2Fe0.9CO0.1O3氧化物的氧物种能选择氧化甲烷生成合成气.在适宜的再氧化条件下,通过连续顺序Redox反应实现了La0.8Sr0.2Fe0.9CO0.1O3氧化物的氧物种氧化甲烷连续生成合成气,消耗的氧物种可通过与气相氧反应而得到补充.但随着Redox反应的进行,氧化物的持续供氧性能下降,钙钛矿结构被破坏.     

用XPS对La1-xSrxCoO3的研究——Ⅲ. LaCoO3的还原及表面状态

本文用XPS研究了LaCoO_3在不同温度下氢气还原的情况, 并表征了钴的还原度。用X-光衍射了解还原后LaCoO_3为金属钴和La_2O_3二相。通过La 3d_(5/2)峰与其shake-up伴峰之间的距离确定La是以La(OH)_3的形式存在于表面。     

Co(III)离子在二氧化铅电极上的阳极形成

文献上曾报导过Co(Ⅱ)离子具有加速PbO_2电极上氧阳极析出过程的作用,并表明当Co(Ⅱ)离子存在时,氧的析出过程有可能通过表面吸附的高价钴氧化物氧化水分子而形成.本文通过浓硫酸溶液中Co(Ⅱ)阳极氧化为Co(Ⅲ)以及O_2阳极析出动力学的研究,表明了O_2的析出和Co(Ⅲ)的形成是通过吸附在电极表面的高价钴(Ⅳ)的OH 基配合物分别氧化水分子和Co(Ⅱ)离子形成的,它与Cr(Ⅲ)、Mn(Ⅱ)离子的阳极氧化过程相类似,而不是通过Co(Ⅱ)离子直接放电形成的.本文利用文献所述的研究方法.在固定硫酸浓度(3.4mol·kg~(-1))下,研究CoSO_4浓度(0.05—0.35mol·drn~(-3))对于O_2和Co(Ⅲ)阳极形成过程分别的影响.在固定CoSO_4(0.2mol·     

水热合成Fe3+掺杂ZnO复合材料及其光催化活性

以Zn(Ac)2·2H2O、Fe(NO3)3·9H2O和NaOH为原料,采用水热法合成了Fe3+掺杂ZnO复合材料. 并用X射线衍射和扫描电子显微镜测试技术对合成样品的结构和形貌进行了表征. 结果表明,Fe3+掺杂ZnO合成产物为直棒状,直径为500 nm,长度为3 μm左右. 样品的紫外可见漫反射分析结果表明,在300～500 nm紫外可见光区域均有强的吸收. Fe3+掺杂ZnO作为光催化剂降解有机染料性能优于纯ZnO材料.     

Comparison of LaFeO3, La0.8Sr0.2FeO3, and La0.8Sr0.2Fe0.9Co0.1O3 perovskite oxides as oxygen carrier for partial oxidation of methane

Comparison of LaFeO3, La0.8Sr0.2FeO3, and La0.8Sr0.2Fe0.9Co0.1O3 perovskite oxides as oxygen cartier for partial oxidation of methane in the absence of gaseous oxygen was investigated by continuous flow reaction and sequential redox reaction. Methane was oxidized to syngas with high selectivity by oxygen species of perovskite oxides in the absence of gaseous oxygen. The sequential redox reaction revealed that the structural stability and continuous oxygen supply in redox re-action decreased over La0.8Sr0.2Fe0.9Co0.1O3 oxide, while LaFeO3 and Lao.sSro.2FeO3 exhibited excellent structural stability and continuous oxygen supply.     

Ce-Fe-Zr-O/MgO整体型氧载体用于化学链部分氧化甲烷制合成气

以MgO为载体,采用球磨法制备了Ce-Fe-Zr-O/MgO粉末状氧载体,进而采用挤压成型法制备了整体型氧载体。研究了两种氧载体化学链部分氧化甲烷制合成气的性能,并通过XRD、H₂-TPR对氧载体进行表征。结果表明,粉末状氧载体中的储氧组分以Ce-Fe-Zr-O固溶体形式存在,而整体型氧载体的制备过程会导致Zr、Fe游离氧化物的形成。粉末状氧载体和整体型氧载体上均存在表面晶格氧和体相晶格氧,其中,体相晶格氧具有高选择性氧化甲烷的性能,可以将甲烷转化成CO和H₂。粉末状氧载体与甲烷反应活性较高,但其存在高含量的表面氧,易导致甲烷的完全氧化。整体型氧载体上体相晶格氧占据优势,可将甲烷选择性氧化为CO和H₂。氧化还原循环实验表明,粉末状氧载体在还原反应发生短时间内容易引起甲烷裂解导致产物气中的H₂/CO物质的量比显著大于2.0,同时产生大量积炭,制约了其循环性能。而整体型氧载体经10次循环实验后,全程反应过程中合成气H₂/CO物质的量比一直维持在2.0附近,显示了较高的循环稳定性能。     

Hydrogen production from a combination of the water-gas shift and redox cycle process of methane partial oxidation via lattice oxygen over LaFeO3 perovskite catalyst

A redox cycle process, in which CH4 and air are periodically brought into contact with a solid oxide packed in a fixed-bed reactor, combined with the water-gas shift (WGS) reaction, is proposed for hydrogen production. The sole oxidant for partial oxidation of methane (POM) is found to be lattice oxygen instead of gaseous oxygen. A perovskite-type LaFeO3 oxide was prepared by a sol-gel method and employed as an oxygen storage material in this process. The results indicate that, under appropriate reaction conditions, methane can be oxidized to CO and H2 by the lattice oxygen of LaFeO3 perovskite oxide with a selectivity higher than 95% and the consumed lattice oxygen can be replenished in a reoxidation procedure by a redox operation. It is suggested that the POM to H2/CO by using the lattice oxygen of the oxygen storage materials instead of gaseous oxygen should be possibly applicable. The LaFeO3 perovskite oxide maintained relatively high catalytic activity and structural stability, while the carbonaceous deposits, which come from the dissociation of CH4 in the pulse reaction, occurred due to the low migration rate of lattice oxygen from the bulk toward the surface. A new dissociation-oxidation mechanism for this POM without gaseous oxygen is proposed based on the transient responses of the products checked at different surface states via both pulse reaction and switch reaction over the LaFeO3 catalyst. In the absence of gaseous-phase oxygen, the rate-determining step of methane conversion is the migration rate of lattice oxygen, but the process can be carried out in optimized cycles. The product distribution for POM over LaFeO3 catalyst in the absence of gaseous oxygen was determined by the concentration of surface oxygen, which is relevant with the migration rate of lattice oxygen from the bulk toward the surface. This process of hydrogen production via selective oxidation of methane by lattice oxygen is better in avoiding the deep oxidation (to CO2) and enhancing the selectivity. Therefore, this new route is superior to general POM in stability (resistance to carbonaceous deposition), safety (effectively avoiding accidental explosion), ease of operation and optimization, and low cost (making use of air not oxygen).     

Partial Oxidation of Methane Over the Perovskite Oxides

Introduction The conversion of methane to syngas is a very appealing route for the conversion of the large reserves of natural gas1, from which a wide variety of valuable hydrocarbons and oxygenates, such as methanol and formaldehyde, can be synthesized. A great research effort is presently being carried out on the catalytic partial oxidation of methane to syngas2. In the present work, two oxides with the perovskite structure, Ba0.5Sr0.5Co0.8Fe0.2O3- and Ba0.5Sr0.5Co0.8Ti0.2O3-?were sys…     

球形尖晶石型钴铁氧体:合成方法及其影响因素

实现了在低温、常压条件下由含铁水滑石微晶到球形尖晶石型铁氧体的合成。结果表明,所合成的铁氧体系平均粒径为1.0μm的规整球。进一步研究发现,铁氧体微球的成型过程受到很多因素影响,例如,球型铁氧体磁性粒子的大小随着晶化过程中溶液的酸碱度的升高而变大;同时外加磁场的存在不但会使球型铁氧体磁性粒子的粒径变大,而且也会使晶化产物的粒子形貌更加趋于规整。另外,还对不同组成的尖晶石型铁氧体微球的形成进行横向比较时发现,合成初期的化合物投料组成对终产物形貌的影响是巨大的,随着投料组成中Fe2+含量的增加,转化过程变得容易,且在投料金属离子组成nCo2+∶nFe2+∶nFe3+为1∶1∶1时,所得的球型铁氧体磁性粒子的粒径最大。相同条件下不同组成的铁氧体微球粒径差异明显,MgFe2O4不能形成球形颗粒,NiFe2O4和CoFe2O4可以形成球形颗粒,其中CoFe2O4形成的颗粒粒径最大。     

气相中Fe~(2+)和H_2O_2作用生成OH自由基的理论研究

利用B3LYP方法，在6-311G基组下研究了气相中Fe~(2+)与H_2O_2作用生成OH自 由基的反应途径，探讨了铁离子对生成羟基自由基所起的作用。结果表明反应的途 径为：Fe~(2+)与H_2O_2首先形成中间体（FeO_2H_2）~(2+)，然后能过O-O键的断 裂生成中间体（HOFeOH）~(2+)，再断Fe-OH键生成羟基自由基，Fe~(2+)和H_2O_2 的电荷强烈相互作用以及Fe~(2+)的d轨道上的电子促进H_2O_2中的O-O键断裂，生 成羟基自由基。     

Double perovskite oxides Sr_2Mg_(1-x)Fe_xMoO(6-δ) for catalytic oxidation of methane

The double perovskite oxides Sr2Mg1-xF exMoO6-δ were investigated as catalysts for the methane oxidation.The structural properties of catalysts were characterized in detail by X-ray diffraction,X-ray photoelectron spectroscopy and X-ray absorption spectroscopy.The catalytic property was strongly influenced by the Fe substitution.The relation between catalytic performance and the degree of Fe substitution was examined with regard to the structure and surface characteristics of the mixed oxides.The Fe-containing catalysts exhibited higher activity attributable to the possible(Fe2+,Mo6+) and (Fe3+,Mo5+)valency pairs,and the highest activity was observed for Sr2Mg0.2Fe0.8MoO6-δ.The enhancement of the catalytic activity may be correlated with the Fe-relating surface lattice oxygen species and was discussed in view of the presence of oxygen vacancies.     

咪唑配位的夹心型杂多化合物Na_9[{Na(H_2O)}_3{Co(C_3H_4N_2)}_3(BiW_9O_(33))_2]·33H_2O的合成，结构和磁性质研究

在pH=7.5的水溶液中，咪唑与Na_2WO_4,Bi(NO_3)_3及Co(NO_3)_2反应，得到 了咪唑配位的新型杂多钨酸盐Na_9[{Na(H_2O)}_3{Co(C_3H_4N_2)}_3(BiW_9O_(33) )_2]·33H_2O，用X射线单晶衍射法及元素分析确定了其结构，晶胞参数为：空间 群P3，a=1.3904(4)nm, b=1.3904(4)nm, c=3.3169(13)nm, γ=120 °,V=5.553(3) nm~3, Z=2, R_1=0.0361，wR_2=0.0507(I>2σ)。杂多阴离子[{Na(H_2O)_3}{Co (C_3H_4N_2)}_3(BiW_9O_(33))_2]~(9-)为夹心式结构，两个三空缺Keggin离子α- B-BiW_9O_(33)~(9-)夹层中的中心离子为交替排列的三个Na(H_2O)~+和三个Co (C_3H_4N_2)~(2+)，中心离子钴的配位数为5，该杂多阴离子具有C_(3v)对称性。 对标题化合物进行了磁性质表征，拟合结果为J=6.90cm~(-1),g=2.10,θ=0.25K， 表明该化合物中的Co(II)三核簇存在着铁磁偶合。     

A computational modelling study of oxygen vacancies at LaCoO3 perovskite surfaces

Atomistic computational modelling of the surface structure of the catalytically-active perovskite LaCoO(3) has been undertaken in order to develop better models of the processes involved during catalytic oxidation processes. In particular, the energetics of creating oxygen ion vacancies at the surface have been investigated for the three low index faces (100), (110) and (111). Two mechanisms for vacancy creation have been considered involving dopant Sr(2+) cations at the La(3+) site and reduction of Co(3+) to Co(2+). For both mechanisms, there is a general tendency that the smaller the cation defect separation, the lower the energy of the cluster, as would be expected from simple electrostatic considerations. In addition, there are clear indications that oxygen vacancies are more easily created at the surface than in the bulk. The results also confirm that the presence of defects strongly influences crystal morphology and surface chemistry. The importance of individual crystal surfaces in catalysis is discussed in terms of the energetics for the creation of oxygen vacancies.     

LaMO3纳米复合钙钛矿氧载体化学循环重整甲烷制合成气

采用溶胶-凝胶法制备了不同B位可变价离子的LaMO3 (M= Cr,Mn,Fe,Co)复合氧化物氧载体,采用X射线衍射、N2吸附-脱附、扫描电镜及CH4程序升温表面反应等手段对氧载体进行了表征,并用于直接选择氧化CH4的反应中.结果表明,Cr,Mn,Fe 和Co均能形成LaMO3纳米复合钙钛矿结构,其氧物种氧化能力大小...     

Atomic‐Scale Insights into Surface Lattice Oxygen Activation at the Spinel/Perovskite interface of Co3O4/La0.3Sr0.7CoO3

Surface lattice oxygen in transition‐metal oxides plays a vital role in catalytic processes. Mastering activation of surface lattice oxygen and identifying the activation mechanism are crucial for the development and design of advanced catalysts. A strategy is now developed to create a spinel Co₃O₄ /perovskite La_0.3Sr_0.7CoO₃ interface by in situ reconstruction of the surface Sr enrichment region in perovskite LSC to activate surface lattice oxygen. XAS and XPS confirm that the regulated chemical interface optimizes the hybridized orbital between Co 3d and O 2p and triggers more electrons in oxygen site of LSC transferred into lattice of Co₃O₄ , leading to more inactive O^2? transformed into active O^2?x. Furthermore, the activated Co₃O₄/LSC exhibits the best catalytic activities for CO oxidation, oxygen evolution, and oxygen reduction. This work would provide a fundamental understanding to explain the activation mechanism of surface oxygen sites.