钴/氧化铝纳米有序阵列复合结构的光学特性研究

关键词：     

Comparison of optical properties of Cu-Al2O3 and Ag-Al2O3 nano-array composite structure

Cu-Al2O3 (Ag-Al2O3) nano-array composite structures were obtained by alternating current (AC) electrodeposition Cu (Ag) into the pores of anodic alumina.     

Optical properties of Ag–Al2O3 nano-array composite structure

Ag/Al₂O₃ nano-array composite structures were obtained by alternating current (AC) electrodeposition of Ag into the pores of anodic alumina membrane (AAM). The ordered wire-grid structure of Ag nanowires formed along a preferential direction, typically 20 nm in diameter, was fabricated. XRD revealed that Ag₂O is also preserved in the pores of AAM. Optical properties of Ag/Al₂O₃ prepared at different annealing temperatures were measured by using spectrometer. Transmission spectra indicate that the transmittance of Ag/Al₂O₃ increases obviously with the increasing of annealing temperature. Polarization spectra indicate that Ag/Al₂O₃ has good polarization in the range of 900–2000 nm, and the extinction ratio increases with the increasing of the annealing temperature or incident angle.     

Structural and Magnetic Properties of the Al2O3/Ge-p/Al2O3/Co System

Technical Physics - The Al2O3/Ge-p/Al2O3/Co system with an Al2O3 buffer layer deposited by ion-plasma sputtering has been experimentally investigated. The dependences of the magnetic properties of...     

Apparent spin polarization decay in Cu-dusted Co/Al2O3/Co tunnel junctions

Co/Al2O3/Co magnetic tunnel junctions with an interfacial Cu layer have been investigated with in situ growth characterization and ex situ magnetotransport measurements. Cu interlayers grown on Co give an approximately exponential decay of the tunneling magnetoresistance with xi approximately 0.26 nm while those grown on Al2O3 have a decay length of 0.70 nm. The difference in decay lengths can be explained by different growth morphologies, and in this way clarifies a present disagreement in the literature. For monolayer coverage of Cu, we show that the tunneling spin polarization is suppressed by at least a factor of 2 compared to Co and beyond approximately 5 ML it becomes vanishingly small.     

Optical properties of ZnO and Al2O3 implanted with silver ions

ZnO and Al₂O₃ samples implanted with 30-keV silver ions with fluences in the interval (0.25–1.00) × 10¹⁷ ions/cm² are studied by the method of optical photometry in the visible part of the spectrum. The optical transmission spectra of the implanted samples exhibit a selective band associated with surface plasmon resonance absorption of silver nanoparticles. The intensity of this band nonmonotonically depends on the implantation fluence. The silver ion depth distribution in the samples is calculated. It is shown that the non-monotonicity observed in experiments is due to an increase in the substrate sputtering ratio with increasing implantation fluence. It is found that vacuum thermal annealing of the implanted Al₂O₃ layers up to 700°C causes a considerable narrowing of the plasmon absorption bandwidth without a tangible change in its intensity. At higher annealing temperatures, the plasmon absorption band broadens and its intensity drops. Annealing of the ZnO films under such conditions causes their complete vaporization.     

Ag/AAO纳米有序阵列复合结构等效光学参量的确定

引入厚度偏差Δd, 修正了薄膜透射率表达式.基于Ag/AAO纳米有序阵列复合结构实验透射光谱(500—2700nm)的两条极值包络线, 定义了一个优化函数, 结合最优化数值算法尝试确定具有较强吸收的Ag/AAO纳米有序阵列复合结构的等效光学参量. 由此计算了该结构的等效折射率n、等效消光系数k、平均等效厚度d以及厚度偏差Δd. 该方法对Ag/AAO纳米复合结构平均等效厚度的相对计算误差仅为0.3%, 与实测厚度基本一致, 且Ag/AAO纳米复合结构的模拟透射谱与实验透射光谱在500—2700nm波段范围内相符. 这表明该计算方法可有效确定Ag/AAO纳米复合结构的等效光学参量, 并与实验结果是自洽的. 关键词： 薄膜光学 光学参量 纳米复合结构 最优化算法     

微弧等离子喷涂碳纳米管/纳米Al2O3-TiO2复合涂层的吸波性能研究

将碳纳米管与纳米Al₂O₃-TiO₂陶瓷粉末超声共混制备了碳纳米管/纳米Al₂O₃-TiO₂复合粉末,测试了复合粉末在2—18GHz波段的电磁参数.研究表明：随着碳纳米管质量分数的增加,碳纳米管/纳米Al₂O₃-TiO₂复合粉末的复介电常数和损耗角不断增大.当碳纳米管质量分数和厚度增加时,复合粉末对电磁波的反射率峰值先增加后减小,而谐振频率不断向低频移动.采用微弧等离子喷涂制备了7wt%碳纳米管/纳米Al₂O₃-TiO₂复合吸波涂层,当厚度为1.5mm时,涂层最小反射率为-24.0dB,当厚度为2.0mm时,涂层小于-10dB的频带宽为3.60GHz,当温度为500℃高温时,1.0mm厚的涂层最小高温反射率为-12.2dB,小于-10dB频带宽为2.0GHz.复合涂层的实际厚度D与理论厚度d呈线关系：d=0.898D+0.515. 关键词： 等离子喷涂 碳纳米管 2O₃-TiO₂')" href="#">纳米Al₂O₃-TiO₂ 吸波性能     

Effects of heat treatment on optical absorption properties of?Ni–P/AAO nano-array composite structure

Ni–P/AAO nano-array composite structure assemblies with Ni and P grown in the pores of anodic aluminum oxide (AAO) membranes were prepared by electroless deposition. The results of SEM, TEM and SAED show that as-deposited Ni–P nanowires have an amorphous structure and a few nanocrystallites form after annealing. The optical absorption spectra reveal that, as the annealing temperature increases, the absorption band edge of the Ni–P/AAO composite structure is obviously blue shifted, which is attributed to a decrease of the internal pressure after heat treatment. Meanwhile, the annealed Ni–P/AAO nano-array composite structure exhibits the absorption behavior of a direct band gap semiconductor. Details of this behavior are discussed together with the implications for potential device applications.     

The optimized preparation and electrochemical properties of LiMn1.95Co0.05O4 and Al2O3-coated LiMn1.95Co0.05O4

Cathode material LiMn_1.95Co_0.05O₄ for lithium ion battery was synthesized via solid state reaction, and calcination temperature and time were investigated, respectively. Thermogravimetry (TG) and differential thermal analysis (DTA) measurements were utilized to determine the calcination temperature of precursor sample. The optimized calcination temperature and time are 850 °C and 15 h. The surface of LiMn_1.95Co_0.05O₄ cathode is coated using Al₂O₃ coating materials. The phase structures, surface morphologies, and element types of the prepared LiMn_1.95Co_0.05O₄ and Al₂O₃-coated LiMn_1.95 Co_0.05O₄ were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), and energy spectrum analysis (EDS). The 0.5 wt% Al₂O₃-coated compound exhibited better specific capacity and capacity retention than bare sample. The initial discharge capacity was 140.9 mAh/g and capacity retention was 96.7 % after 10 cycles at 0.1 C. Such enhancements are attributed to the presence of a stable Al₂O₃ layer which acts as the interfacial stabilizer on the surface of LiMn_1.95Co_0.05O₄.     

Optical diagnostics of physicochemical properties of NiO/Al2O3 nanocomposites upon exposure to different gases and heat

We have studied nanostructural and optical properties of composites of nanostructured nickel oxide films on a substrate from porous aluminum oxide NiO/Al₂O₃ in the UV, visible, and IR spectral ranges on exposure of composites to different gases, vacuum, and heat. We have found that, upon irradiation of NiO/Al₂O₃ composites by laser radiation at a wavelength of 633 nm, they demonstrate a high sensitivity to carbon monoxide CO in the range of the excitonic absorption of nickel oxide. We assume that an increase in the transmission coefficient of the composite in the excitonic absorption band is determined by luminescence that is caused by the oxidation reaction of carbon monoxide. The sensitivity of composites to CO is enhanced with decreasing the size of NiO nanoparticles and after evacuation. The values of the diffuse reflection coefficient at the laser radiation wavelength of 633 nm correlate with the size of nickel oxide nanoparticles. Spectral changes in the range of the fundamental absorption band of NiO that occur in the IR range and in diffuse reflection spectra are related to the appearance of carbon-containing compounds in the composite exposed to CO.     

Properties of strontium titanate in the SrTiO3/CeO2/Al2O3 multilayered structure

Studies of the crystal structure, elemental composition, and dielectric properties of strontium titanate films in SrTiO₃/CeO₂/Al₂O₃ multilayered structures are reported. Data on the crystal lattice and impurity contents have been obtained, and temperature and electric field dependences of the dielectric properties of SrTiO₃ films in the microwave range have been measured. An analysis of the results is made to establish the reason for the nonmonotonic dependence of the small-signal dielectric permittivity of SrTiO₃ films on temperature. Fiz. Tverd. Tela (St. Petersburg) 39, 1024–1029 (June 1997)     

Electrochemical behavior of Al2O3/Al composite coated Al electrodes through surface mechanical alloying in alkaline media

The behavior of $A{l}_2{O}_3/Al$ composite coated Al electrodes fabricated by surface mechanical alloying ‘SMA’ was studied. The work was accomplished using Cyclic voltammetry and electrochemical impedance spectroscopy (EIS) techniques in alkaline media $2MKOH$ were done at room temperature. Results show hydroxyl ions accumulate on the surface due to Al deformation micro cavities filling with $A{l}_2{O}_3$ until full charge blockage reached. A barrier cover layer development causing an increase of both resistance and capacitance as it becomes more stable and thinner with exposure time increase. Migrating hydroxyl ion inside micro cavity changed its composition from Al₂O₃ to stable tetrahedral $Al{\left(OH\right)}_4^{?}$ aluminate ions. Therefore future benefits could be reached by developing such surfaces having charge accumulation that enables environmental interaction.     

Al2O3/C复合微粒子散射强度分布的计算

利用A.L.Aden和M.Kerker复合微粒子Mie散射理论计算了Al2O3/C复合微粒子的散射强度分布函数,分析了影响散射强度分布的因素.     

Preparation and electrochemical properties of EG/Fe2O3/C composite

Ionics - The present paper deals with the studies concerning electrochemical properties of the expanded graphite/iron oxide/carbon (EG/Fe2O3/C) composite produced by deep cathodic reduction. The...     

Hydrothermal synthesis and electrochemical performance studies of Al2O3-coated LiNi1/3Co1/3Mn1/3O2 for lithium-ion batteries

LiNi_1/3Co_1/3Mn_1/3O₂ nanocrystallites were synthesized by a one-step hydrothermal method, and uniform second particles were formed by a subsequent calcination process. X-ray diffraction results indicate that the as-synthesized material can be indexed by α-NaFeO₂ layered structure with R-3 m space group. The results of Rietveld refinements show the I ₀₀₃/I ₁₀₄ value of the material is 2.032, and the nanostructured material presents low cation mixing, small cell volume, and a consequent suppression of lattice strain. The rate performances of the as-synthesized material can be further improved by coating Al₂O₃. The discharging capacity of Al₂O₃-coated material reaches 154.4 mAh g^?1, and the capacity retention maintains 80.3 % after 50 cycles at 5 C in the voltage range of 2.5 to 4.5 V, while those of the bare one is only 139.0 mAh g^?1 and 71.6 %, respectively. The transmission electron microcopy observation shows no zigzag layer exists on the surface of particle after cycles for Al₂O₃-coated LiNi_1/3Co_1/3Mn_1/3O₂. Compared to bare LiNi_1/3Co_1/3Mn_1/3O₂, the de-intercalation potential difference before and after cycles of Al₂O₃-coated one is smaller. This indicates that Al₂O₃ coating can reduce the electrochemistry polarization in the electrode bulk.     

Dielectric breakdown phenomena in Al2O3 filled DGEBA/MDA/SN composite system

Dielectric breakdown phenomena by electrical treeing deterioration was investigated in the new epoxy resin system DGEBA/MDA/SN filled with Al₂O₃. As the filler content increased, the maximum electric field at breakdown increased and then decreased with increase of defects such as voids, impurities and delamination or peeling between filler and matrix. As the electrode separation increased, the breakdown voltage increased, but the breakdown strength decreased and then saturated to 17 kV/mm. Also, the maximum electric field at the tip when the system was failed increased. The electrical tree initiated from the side of the needle electrode was not from the tip where the reinforced field is the highest. The electrical tree was blocked by the filler. The interface condition of filler and polymer matrix played an important role in the electrical treeing resistance. The final breakdown phenomena showed fan-type crack as observed in the non-filled system.     

Cole-Cole Analysis of the Superspin Glass System Co 80 Fe 20 /Al 2 O 3

Ac susceptibility measurements were performed on discontinuous magnetic multilayers [Co 80 Fe 20 ( t )/Al 2 O 3 (3 nm)] 10 , t = 0.9 and 1.0 nm, by Superconducting Quantum Interference Device (SQUID) magnetometry. The CoFe forms nearly spherical ferromagnetic single-domain nanoparticles in the diamagnetic Al 2 O 3 matrix. Due to dipolar interactions and random distribution of anisotropy axes the system exhibits a spin-glass phase. We measured the ac susceptibility as a function of temperature 20 h T h 100 K at different dc fields and as a function of frequency 0.01 h f h 1000 Hz. The spectral data were successfully analyzed by use of the phenomenological Cole-Cole model, giving a power-law temperature dependence of the characteristic relaxation time c and a high value for the polydispersivity exponent, f , 0.8, typical of spin glass systems.     

TiO2/Al2O3薄膜的原子层沉积和光学性能分析

采用原子层沉积技术在熔石英和BK7玻璃基片上镀制了TiO2/Al2O3薄膜,沉积温度分别为110℃和280℃。利用X射线粉末衍射仪对膜层微观结构进行了分析研究,并在激光损伤平台上进行了抗激光损伤阈值测量。采用Nomarski微分干涉差显微镜和原子力显微镜对激光损伤后的形貌进行了观察分析。结果表明,采用原子层沉积技术镀制的TiO2/Al2O3增透膜的厚度均匀性较好,Φ50 mm样品的膜层厚度均匀性优于99%;光谱增透效果显著,在1 064 nm处的透过率〉99.8%;在熔石英和BK7基片上,TiO2/Al2O3薄膜在110℃时的激光损伤阈值分别为（6.73±0.47）J/cm2和（6.5±0.46）J/cm2,明显高于在280℃时的损伤阈值。