Study of the Lead Environment in Liquid and As-Dried Precursors of PZ, PT and PZT Thin Films

The environment of lead and zirconium atoms in liquid and as-dried precursors for PbZrO3 (PZ), PbTiO3 (PT) and Pb1.1Zr0.53Ti0.47O3 (PZT) thin film deposition were analyzed by EXAFS. The sols were prepared by 2-methoxyethanol route with lead acetate and lead oxide as lead sources. Pb—O—M (M = Zr and/or Ti, depending on the sol composition) linkages were determined in all sols. The choice of lead source weakly influences the lead environment, and strongly influences that of zirconium in both PZ and PZT sols. By drying lead oxide based sols the Pb–M correlation is moderately reduced in PZ, PT and is strongly reduced in PZT.     

A Study of Amorphous Precursors for PbZrO3-PbTiO3 Based Ceramic Materials

Amorphous precursors for PbZrO₃ and PbTiO₃ ceramics were prepared from lead acetate and the transition metaln-propoxide inn-propanol orn-butoxide inn-butanol and hydrolysed with an excess of water. According to GLC and TGA/EGA analyses, the type of alkoxide group influences distinctly the structure of heterometallic precursors, i.e., oxo or acetate bridging, and the amounts of hydroxyl and organic groups bound to the metal network. The local environments of metal atoms in the amorphous precursors were also studied by EXAFS. The analysis reveals that in Pb−Zr precursors alkoxide groups modify the coordination spheres of the zirconium atoms. Conversely, local environments of both lead and titanium atoms within the analysed range of 3.4 A depend weakly on the type of alkoxide used.     

29Si and 17O NMR investigations on Si−O−Ti bonds in solutions of diphenylsilanediol and titanium-tetra-isopropoxide

The structural units in diphenylsilanediol/titanium-isopropoxide solutions with molar ratio Si:Ti between 1:0.1 and 1:5 were examined by means of ²⁹Si and ¹⁷O NMR. The main component in solutions with molar ratio Si/Ti=1:0.1 is the chain-like octaphenyltetrasiloxanediol. With increasing Ti-isopropoxide content (1:0.25–1:05) Si–O–Ti units of the spirocyclic titanosiloxane Ti[O₅Si₄(C₆H₅)₈]₂ prevail in the solutions accompanied by the chain-like tetrasiloxanediol. The ²⁹Si NMR spectra of 1:1 solutions indicate a lot of different Si containing building units with chemical shifts mainly between-40 and-46 ppm. The signals with a chemical shift between-40 and-46 ppm are probably caused by Si atoms which are connected via oxygen bridges directly (Si–O–Ti) or indirectly (Si–O–Si–O–Ti) with titanium. Contrary to the 1:1 solutions only one or two different species with Si–O–Ti units are present in high Ti-alkoxide containing solutions (1:5). ²⁹Si and ¹⁷O NMR results reveal a quick hydrolysis of the Ti–O–Si bonds to titanium-oxo-hydroxo-polymers and phenylsiloxanediols or their isopropyl esters after the addition of water to the solutions. This separation into species only containing either Ti–O–Ti or Si–O–Si bonds can entail a decreased homogeneity of the reaction products on a molecular level.     

Syntheses and Characterization of Polymetallosiloxanes from Silicic Acid and Metal Chlorides

Syntheses and characterization of polymetallosiloxanes by the non-hydrolysis sol-gel process using no metal alkoxides were investigated. The reaction of silicic acid (SA) with MCl₄ (M = Ti, Zr) in the molar ratios SA/MCl₄ = 0.5–3.0 using a tetrahydrofuran-methanol solvent formed polymetallosiloxane (PMS), which was insoluble in organic solvents regardless of the molar ratio. The PMS was isolated as esterified polymetallosiloxane by esterification with isopropyl alcohol for various periods, which were soluble in methanol, acetone, and tetrahydrofuran. The number average molecular weight was 1000–3200 for esterified polytitanosiloxane and 3400–11000 for esterified polyzirconosiloxane. Esterified polymetallosiloxanes had no melting point but decomposition point. The results of analytical data indicated that esterified polymetallosiloxane and/or polymetallosiloxane consisted of the main chain of Si–O–Si and Si–O–M linkage with the pendants of alkoxy, silanol, and chloro group.     

Refractive Index Adjustment of SiO<Subscript>2</Subscript> Gel Glass with Zirconium Oxychloride

ZrO₂-SiO₂ binary oxide gel glasses with various Zr contents were prepared by the sol–gel method with zirconium oxychloride and tetraethoxysilane as precursors. It is found that the refractive index of mixed oxide gel glass is linear with the Zr content and suitable heat treatment will give rise to an increase in the refractive index. By employing FTIR techniques, a new Zr—O—Si bond has been investigated with part of the zirconium ions being incorporated into the silica network. The capability to tune the refractive index for the blend sample with Zr ions and to obtain a stable refractive index at relative low treatment temperature suggests that the gel glass is potential matrix for doping with near IR fluorescence organic dyes and make them promising materials for active optical waveguides.     

Design of Homogeneous Hybrid Materials through a Careful Control of the Synthetic Procedure

Sols for the synthesis of hybrid organic-inorganic materials have been prepared by mixing zirconium n-propoxide and methacryloxypropyltrimethoxysilane (MPS). The synthesis was done in two steps: a 15 minute hydrolysis of a MPS : H₂O : EtOH 1 : 1 : 2 mixture and then addition of 0.5 molar equivalent of zirconium alkoxide. All the experimental parameters—hydrolysis ratio, pH, dilution, pre-hydrolysis time—have been optimized through a detailed ²⁹ Si and ¹⁷O NMR analysis. Immediately after the addition, 94% of the initial water was consumed for the formation of Si–O–Zr bridges. Cleavage of these bonds, associated with formation of Si–O–Si and Zr–O–Zr bridges are then observed during the aging time.     

Single crystal structure determination of a new zirconium N-ethylpyridinium phosphonate: Zr(O(3)PCH(2)CH(2)NC(5)H(5))(F(-))(3)

We describe the structure of a new zirconium N-ethylpyridinium phosphonate, Zr(O(3)PCH(2)CH(2)NC(5)H(5))(F(-))(3), that has been determined by single-crystal X-ray analysis (monoclinic, P2(1)/c (No. 14), a = 12.3634(12) A, b = 9.3090(17) A, c = 9.8077(13) A, beta = 112.819(8) degrees, V = 1040.4(3) A(3), Z = 4). This structure is unlike any other reported zirconium phosphonate. Octahedral coordination about zirconium is completed by three oxygen atoms of three different phosphonate groups and three fluoride ligands. The structure is composed of corrugated infinite layers of these Zr octahedra that corner share their three oxygen atoms with the phosphonate tetrahedra. The appended cationic pyridinium groups lie between the inorganic sheets and are charge-balanced by the [Zr(O(3)P-)(3)F(3)](-) octahedra. This structure represents a new example of the structure-directing influence of cationic organic ligands on the zirconium phosphonate framework.     

Influence of structural disorder on the photoluminescence emission of PZT powders

Intense and broad visible photoluminescent (PL) band was observed at room temperature in disordered Pb(Zr0.53Ti0.47)O3 powders. Structural order-disorder was evaluated by different methods. XANES results pointed to the presence of different coordination modes of disordered Ti powders, and in the ordered sample the local structure around titanium atoms is characteristic of the structurally ordered PZT with only TiO6 units. Only samples containing simultaneous structural order and disorder in their network present the intense visible PL emission at room temperature.     

Titanium and zirconium complexes of preorganized tripodal triaryloxide ligands

Tri(2-oxy-3,5-di-tert-butylphenyl)methane, [O3]3- has been used to prepare titanium and zirconium complexes of the general formula [O3]MX (M = Ti, X = NEt2, Cl, CH2Ph; M = Zr, X = CH2Ph). The tripodal [O3] ligand in titanium complexes adopt the syn- and the anti-conformation, while the syn complex of zirconium undergoes facile C-H activation to give a 5-carbametalatrane [O3C]Zr(THF)3.     

Silica-Zirconia Sol–Gel Coatings Obtained by Different Synthesis Routes

Homogeneous xSiO₂-(1−x)ZrO₂ coatings have been prepared onto glass-slides, monocrystalline Si and stainless steel (AISI 304) using sols prepared via acid and basic catalysis. Zirconium tetrabutoxide (TBOZr), zirconium n-propoxide (TPZ), tetraethoxysilane (TEOS) and methyltriethoxysilane (MTES) were used as precursors of zirconia and silica, respectively. The different parameters involved in the synthesis procedure, as molar ratios H₂O/alkoxides, NaOH/alkoxides, and sintering temperature have been analysed, correlating the stability and rheological properties of the sols. The evolution and structure of the sols and coatings have been studied by FTIR. Coatings have been prepared by dipping from acid and basic sols. Electrophoretic Deposition (EPD) technique has also been used to prepare coatings onto stainless steel from basic particulate sols in order to increase the critical thickness. A maximum thickness of 0.5 μ m was reached by both dipping and EPD process for 75SiO₂: 25 ZrO₂ composition. The critical thickness decreases with ZrO₂ amount depending strongly of the drying conditions. Si–O–Zr bonds have been identified by FTIR, indicating the existence of mixed network Si–O–Zr in the coatings obtained by the different routes. Crystallisation of ZrO₂(t) was only observed at high sintering temperature (900^∘C) by FTIR and confirmed by DRX.     

环戊二烯基二硫代氨基甲酸钛(Ⅳ), 锆(Ⅳ)配合物的合成及结构表征

(RCp)~2MCl~2, (RCp)TiCl~3分别与N-(4-苯基-2-噻唑基)二硫代氨基甲酸钾和3-苯基-5-(2-呋喃基)-吡唑啉-1-二硫代甲酸钠进行反应, 合成了三十二个未见报道的(RCp)M(S~2CNHR')~nCl~3~-~n,(RCp)~2M-(S~2CNHR')~nCl~2~-~n [R=H, Me; M=Ti, Zr; R'=4-苯基噻唑基(PTDTC), n=1,2,3] 以及(RCp)M(S~2CR^2)~nCl~3~-~n,(RCp)~2M(S~2CR^2)~nCl~2~n[R=H,Me;M=Ti,Zr,R^2=3-苯基-金-(呋喃-2)吡唑啉基(PFPDTC), n=1,2,3]型配合物。所有配合物经元素分析、UV、IR和^1H NMR谱证实, 二硫代氨基甲酸是以双齿配体键合的。     

环戊二烯基二硫代氨基甲酸钛(Ⅳ)、锆(Ⅳ)配合物的合成及结构表征

(RCp)_2MCl_2,(RCp)TiCl_3分别与N-(4-苯基-2-噻唑基)二硫代氨基甲酸钾和3-苯基-5-(2-呋哺基)-吡唑啉-1-二硫代甲酸钠进行反应,合成了三十二个未见报道的(RCp)M(S_2CNHR′)_nCl_(3-n),(RCp)_2M-(S_2CNHR′)_nCl_(2-n),[R=H,Me;M=Ti,Zr;R′=4-苯基噻唑基(PTDTC),n=1,2,3]以及(RCp)M(S_2CR~2)_nCl_(3-n),(RCp)_2M(S_2CR~2)_nCl_(2-n)[R=H,Me;M=Ti,Zr,R~2=3-苯基-15-(呋喃-2)吡唑啉基(PFPDTC),n=1,2,3]型配合物。所有配合物经元素分析、UV、IR和'H NMR谱证实,二硫代氨基甲酸是以双齿配体键合的。     

Coordination Polyhedra TiOn in Crystal Structures

The Voronoi–Dirichlet polyhedra (VDP) and the method of intersecting spheres were used to perform crystal-chemical analysis of 532 compounds containing 940 crystallographic sorts of titanium atoms in TiO _n coordination polyhedra. It was found that Ti(IV) or Ti(III) atoms can coordinate four to eight oxygen atoms. For a constant valence state and a constant coordination number (C.N.) of titanium, the Ti–O bond lengths vary by 0.1–1.0 Å. At C.N. #gt; 5, the volume of the metal VDP remains virtually unchanged; when the C.N. decreases to 4, the VDP volume increases by 2–3 ų. For a constant C.N., Ti(IV) Ti(III) transition is accompanied by an increase in the VDP volume of metal atoms of 0.5–1.9 ų. The VDP characteristics of the Ti atoms can be used to determine their valence state and to identify the titanium–metal bonds in the structures of compounds.     

Catalytic thermal and photo-induced CH and CC activation reactions of alkanes with ansa amido functionalized half-sandwich complexes and methylalumoxane

In the literature most of the dehydrogenation reactions of alkanes are described as CH activation reactions of cyclooctane. The best results of CH activation reactions have been found for the reaction of MAO activated metallocene complexes and cyclooctane at temperatures over 300 °C.The application of ansa amido functionalized half sandwich compounds of the type Ind′Si(Me)2NtBuMCl2 (Ind′= monosubstituted indenyl); M = Ti, Zr, Hf) for CH and CC activation reactions is completely unknown in the literature.In contrast to the dehydrogenation reactions of cyclooctane and the metallocene complexes of the group 4 metals, where the zirconocene complexes give higher TONs than the titanocene complexes the ansa amido functionalized titanium complexes give more than two times higher TONs than the corresponding Zr or Hf complexes. The ansa amido functionalized ligand increases the TONs for the Ti complexes and decreases the TONs of the Zr complexes.In contrast to the metallocene complexes, the ansa amido functionalized dichloride complexes of Ti show also a higher activity than the corresponding Zr complexes. It is known that the photolysis of organometallic titanium, zirconium and hafnium (IV) compounds can give M(III) radicals. The formation of the active Ti metal centre is easier than in the case of the corresponding Zr and Hf metal compounds.     

Metal-carbon clusters: the origin of the delayed atomic ion

Studies of the emission of electrons from excited metal-carbon cluster systems that include the Met-Car (M(8)C(12), where M is Ti, Zr, and V) also have revealed the evolution of a delayed atomic ion. The source of the delayed atomic ion, which involves the emission of ionized atoms on the microsecond time scale, is the focus of this investigation. By studying the delayed ionization of mixed zirconium and titanium carbon complexes produced in a laser vaporization source coupled to a time-of-flight mass spectrometer, for the first time both the zirconium and titanium delayed atomic ions were observed to be emitted in the same experiment. These studies allowed a determination that the source of the delayed atomic ion is an excited metal dicarbide. A plausible mechanism involving the excitation of a high Rydberg state of the metal dicarbide prior to an excited ion pair separation is proposed.     

Synthesis, structure, and photoluminescence property of a new layered zirconium phosphate |Co(dien)(2)|[Zr(4)H(8)P(5)O(26)] x 3H(2)O

A new layered zirconium phosphate |Co(dien)(2)|[Zr(4)H(8)P(5)O(26)] x 3H(2)O (denoted ZrPO-CJ37) has been synthesized hydrothermally by using a racemic mixture of a chiral cobaltammine complex Co(dien)(2)Cl(3) as the template. Its structure is determined by single-crystal X-ray diffraction analysis and further characterized by X-ray powder diffraction, inductively coupled plasma, thermogravimetric, UV-vis, and photoluminescence analyses. The inorganic layer of ZrPO-CJ37 is built up from the linkage of Zr-centered octahedra and P-centered tetrahedra via vertex oxygen atoms forming a 4.6-net sheet. Its structure features the edge-sharing chains of Zr(OM)(6) (M = P, H) octahedra. The cobaltammine complex cations are located in the interlayer region and interact with the host network through H bonds. ZrPO-CJ37 exhibits interesting photoluminescence in the UV-vis spectral region. The edge-sharing chains of Zr(OM)(6) octahedra in the inorganic layer might be responsible for this unusual photoluminescence.     

Sol-Gel Synthesis of Nanocrystalline PZT Using a Novel System

A simple system has been developed for the preparation of lead zirconate titanate, Pb(Zr _x Ti_{1 – x} )O₃ powders by sol-gel process. To achieve stable and homogeneous precursor solutions, chelating ligands such as acetic acid and acetylacetone have been used for the chemical modification of titanium and zirconium starting precursors. Phase-pure PZT powders were obtained, through a pyrochlore-free pathway, from the amorphous xerogel after heat treatment at 600°C. The formation of the crystalline phase, compositional homogeneity, sinterability, dielectric and piezoelectric characteristics of PZT are reported.     

Structural evolution from the sol to the PbZrO<Subscript>3</Subscript> precursor powders prepared by an alkoxide-based sol–gel route

PbZrO₃ powders have been prepared by an alkoxide-based sol–gel route, starting from lead acetate, zirconium n-butoxide, and n-butanol as a solvent, and hydrolysed with different amounts of water in neutral and alkaline medium. The local environment of Zr and Pb atoms was pursued from the sol to the dried (150 °C) and heated (400 °C) powders, by extended x-ray absorption fine structure (EXAFS). The analysis of the sol revealed links between Pb and Zr, and even more links between Zr and Zr. The metal neighbourhoods in the dried powders are not influenced by the hydrolysis conditions. Pb-Zr correlations are gradually lost from the sol to the dried and heated powders, while the loss of Zr–Zr correlations is considerably lower.     

Synthesis, characterization, and materials chemistry of Group 4 silylimides

This paper focuses on the development of potential single source precursors for M-N-Si (M = Ti, Zr or Hf) thin films. The titanium, zirconium, and hafnium silylimides (Me(2)N)(2)MNSiR(1)R(2)R(3) [R(1) = R(2) = R(3) = Ph, M = Ti(1), Zr (2), Hf (3); R(1) = R(2) = R(3) = Et, M = Ti (4), Zr (5), Hf (6); R(1) = R(2) = Me, R(3) = (t)Bu, M = Ti (7), Zr (8), Hf (9); R(1) = R(2) = R(3) = NMe(2), M = Ti (10), Zr (11), Hf (12)] have been synthesized by the reaction of M(NMe(2))(4) and R(3)R(2)R(1)SiNH(2). All compounds are notably sensitive to air and moisture. Compounds 1, 2, 4, and 7-10 have been structurally characterized, and all are dimeric, with the general formula [M(NMe(2))(2)(μ-NSiR(3))](2), in which the μ(2)-NSiR(3) groups bridges two four-coordinate metal centers. The hafnium compound 3 possesses the same basic dimeric structure but shows additional incorporation of liberated HNMe(2) bonded to one metal. Compounds 11 and 12 are also both dimeric but also incorporate additional μ(2)-NMe(2) groups, which bridge Si and either Zr or Hf metal centers in the solid state. The Zr and Hf metal centers are both five-coordinated in these species. Aerosol-assisted CVD (AA-CVD) using 4-7 and 9-12 as precursors generates amorphous films containing M, N, Si, C, and O; the films are dominated by MO(2) with smaller contributions from MN, MC and MSiON based on XPS binding energies.     

On the Existence and Hydrolytic Stability of Titanosiloxane Bonds in the System: Glycidoxypropyltrimethoxysilane-Water-Titaniumtetraethoxide

Heterometal materials based on glycidoxypropyltrialkoxysilane and titaniumalkoxide are used for optical applications and require a high homogeneity on the molecular level. The presence of heterometal titanosiloxanes, their distribution and hydrolytic stability should influence the homogeneity of these materials. 29Si and 17O NMR spectroscopy has been used to investigate sols with molar ratios Si : Ti = 1 and H2O : OR (H) = 0.5 – 2.0 and their gels after heat treatment at 130°C. The presence of Si—O—Ti bonds in sols with a low water content (H < 0.2) and in the corresponding gels was identified by the high-field shift of the 29Si NMR signals of T1 and T2 units of up to 2–3 ppm compared to corresponding signals of homo-condensed Si—O—Si bonds. The existence of Si—O—Ti bonds in the sols is supported by 17O NMR spectra which show a characteristic signal around 340 ppm. A cleavage of the Si—O—Ti bonds occurs with increasing water/OR ratio in the sols. The cleavage of the heterometal bonds and the building up of homo-condensed species leads to a separation into areas with predominantly Ti—O—Ti and Si—O—Si bonds resulting in a decreased molecular homogeneity of the materials.