Distribution of charge in the process of coating Fe powder by electrolysis in a fluidized bed

Theoretical calculations of the amount of Ni that is applied electrolytically in the form of a coating on Fe powder particles in a fluidized bed are based upon the assumption of distribution of charge between the surface of the solid cathode and the powder particles present in the working volume of the electrolyte. The experimentally measured data show good agreement with theory. The efficiency of the coating process is rather low because of inhibition of the process by hydroxocomplexes formed in the course of electrolysis. The inhibition effect becomes more significant in the case of high suspension density, small powder particles, high current density, and prolonged time of electrolysis. Received: 5 May 1997 / Accepted: 30 June 1997     

Dynamic relaxation behavior of copolymers of n-butyl methacrylate with n-butyl acrylate and of 2-hydroxyethyl methacrylate with ethyl acrylate,n-butyl acrylate,and dodecyl methacrylate

The effect of the α-methyl group on the mobility of the main and side chains of methacrylateacrylate copolymers has been investigated. Poly(ethyl acrylate) shows a small secondary loss maximum (attributed to the rotation of ? COOR side chains) at 145 K, while in the case of poly(n-butyl acrylate) this relaxation process is smeared out or possibly absent. On the contrary, poly(n-butyl methacrylate) and poly(2-hydroxyethyl methacrylate) exhibit secondary relaxations at about 278 and 301 K, respectively. From the dynamic mechanical response spectra of methacrylate-acrylate copolymers one can see that the removal of the α-methyl group causes a qualitative change in the molecular mechanism of the secondary relaxation, presumably as a consequence of the different participation of the main chains. The existing data, however, are insufficient to quantify these differences. The low-temperature relaxation attributed to internal motion within the side groups is not distinctly affected by the presence of α-methyl groups. If both components of the copolymer display the low-temperature relaxation (above 77 K), the loss maxima preserve their identity to a large extent. The effect of copolymer composition on the main (glass) transition temperature has been described by means of a one-parameter equation.     

Analysis and purification of 2-hydroxyethyl methacrylate by means of thin-layer chromatography.

Poly(2-hydroxyethyl methacrylate) is nowadays accepted as a biocompatible, safe and stable hydrogel for medical use. In this paper, the use of thin-layer chromatography for the analysis and small-scale preparation of the initial monomer, 2-hydroxyethyl methacrylate, is described. Development on silica gel, with n-hexane-diethyl ether (1:1, v/v) and/or n-hexane-isobutyl methyl ketone-n-octanol (9:2:1, v/v; saturated with 25% nitric acid) is recommended for qualitative analysis. Preparative-scale work is preferably carried out on sulphuric acid-impregnated silica gel, with n-hexane-diethyl ether (1:1, v/v) as mobile phase. Inhibitors are detected by thin-layer chromatography and a drop-test procedure with diazotised sulphanilic acid. The nature of the contaminants present in several commercial samples of 2-hydroxyethyl methacrylate is discussed. n20D values are reported for the system 2-hydroxyethyl methacrylate-water.     

Electrospinning of the hydrophilic poly (2-hydroxyethyl methacrylate) and its copolymers with 2-ethoxyethyl methacrylate

The goal was to electrospin 2-hydroxyethyl methacrylate — based biocompatible polymers and prepare submicron fibres (nanofibers) for biomedicinal applications. Syntheses of poly(2-hydroxyethyl methacrylate) (HEMA) and its copolymer with 2-ethoxyethyl methacrylate (EOEMA), and their characterization by viscometry and molecular weight are described. Their relation to electrospinning is discussed. Electrospinning of HEMA homopolymer from water-ethanol is successful for molecular weights 6.31 × 10⁵ and 1.80 × 10⁶ g/mol. Electrospinning of HEMA/EOEMA copolymers is feasible from ethanol.      

Kinetics and mechanism of emulsifier-free emulsion polymerization. III. Styrene/nonionic comonomer (2-hydroxyethyl methacrylate) system

The emulsifier-free emulsion polymerizations of styrene in the presence of about 0.33–2.7% (relative to styrene) of the water soluble comonomer, 2-hydroxyethyl methacrylate (HEMA), and of the initiator, potassium persulfate (KPS), were carried out. It was found that KPS plays a predominant role in the particle nucleation process, since the number density of polymer particles (N_p) was dependent on the 0.97-power of [KPS]. The nucleation ability of HEMA was weak, since N_p was dependent only on the 0.17-power of [HEMA]. The particle nucleation stage ceased quite early before 1% conversion, leading to nearly monodispersed polymer particles. The nucleation is suggested to be via the homogeneous nucleation mechanism. The particles grow via the core-shell structure mechanism (shell region polymerization), since the particle size is rather large—from 1500 to 6000 Å. The amount of HEMA can affect the shell thickness and physical properties of the shell, such as the monomer swelling capacity and monomer diffusion rate.     

Production of anomalous particles in the process of emulsifier-free emulsion copolymerization of styrene and 2-hydroxyethyl methacrylate

It was found that copolymer particles produced by emulsifier-free emulsion copolymerization of styrene and 2-hydroxyethyl methacrylate had an anomalous shape with uneven surface. The formation mechanism is discussed.     

Controlled/living polymerization of 2‐(diethylamino)ethyl methacrylate and its block copolymer with tert‐butyl methacrylate by atom transfer radical polymerization

Polymerization of 2‐(diethylamino)ethyl methacrylate (DEAEMA) via homogeneous atom transfer radical polymerization under various reaction conditions is described. The effects of the initiators and solvents were examined. With 1,1,4,7,10,10‐hexamethyl triethylenetetramine/copper(I) chloride/p‐toluenesulfonyl chloride as the ligand/catalyst/initiator system in methanol, poly(DEAEMA) with a polydispersity index as low as 1.07 was synthesized. Kinetic studies demonstrated the polymerization was very well controlled and exhibited the living characteristic of the process. Well‐defined block copolymers of DEAEMA and tert‐butyl methacrylate (tBMA) were successfully synthesized. The copolymers could be synthesized with equally good results by starting with either p(DEAEMA) or p(tBMA) as the macroinitiators. However, only the macroinitiators terminated with chlorine should be used. The corresponding macroinitiators with bromine as a transferable group did not yield well‐defined copolymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2688–2695, 2003     

Controlled polymerization of 2‐(diethylamino)ethyl methacrylate and its block copolymer with N‐isopropylacrylamide by RAFT polymerization

Poly(2‐(diethylamino)ethyl methacrylate) (PDEAEMA) homopolymers with low polydispersities were synthesized by reversible addition fragmentation chain transfer (RAFT) radical polymerization. The performances of two chain transfer agents, 2‐cyanoprop‐2‐yl dithiobenzoate and 4‐cyanopentanic acid dithiobenzoate (CPADB), were compared. It was found that the polymerization of 2‐(diethylamino) ethyl methylacrylate was under good control in the presence of CPADB with 4,4′‐azobis(4‐cyanopentanoic acid) (ACPA) as initiator in 1,4‐dioxane at 70 °C. The kinetic behaviors were investigated under different CPADB/ACPA molar ratios. A long polymerization inhibition period was observed at high [CPADB]/[ACPA] ratio. The influences of [CPADB]/[ACPA] ratio, monomer/[CPADB] ratio, and temperature were studied with respect to monomer conversion, molecular weight control, and polydispersity index (PDI). The PDI decreased from 1.21 to 1.12, as the CPADB/ACPA molar ratio changed from 2 to 10. The molecular weight of PDEAEMA could be controlled by monomer/CPADB molar ratio. The control over MW and PDI was improved as the temperature increased from 60 to 70 °C; however, an additional increase to 80 °C led to a loss of control. Using PDEAEMA macroRAFT agent, pH/thermo double‐responsive block copolymers of PDEAEMA and poly(N‐isopropylacrylamide) (PDEAEMA‐b‐PNIPAM) with narrow polydispersity (PDI, 1.24) were synthesized. The lower critical solution temperature of PDEAEMA‐b‐PNIPAM block copolymer depended on the environmental pH. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3294–3305, 2008     

Granulation of core particles suitable for film coating by agitation fluidized bed II. A proposal of a rapid dissolution test for evaluation of bitter taste of ibuprofen

To prepare powdered drugs that do not have a bitter taste, a film coating covering the surfaces of the core particles is required. The dissolution rate of ibuprofen from the coated particles changes according to the physical properties of the core particles. In this study, the effects of the physical properties of granules prepared by using several scales of agitation fluidized beds on the drug dissolution rate were investigated. The dissolution rate of ibuprofen decreased when the apparent density and shape factor of the granules increased. In contrast, the dissolution rate of the drug increased with the friablility of the granules increased. Thus, the structures of the granules appear to affect the dissolution rate of the drug to a large degree. A rapid dissolution test that can be used to investigate the early dissolution rate of ibuprofen in vitro was proposed to evaluate the taste-masking level of the coated particles. The bitter taste-masking level of the coated particles was successfully confirmed by using this novel test method.     

Surface properties and liquid crystal alignment behavior of poly(2-hydroxyethyl methacrylate) derivatives with alkyl ester side chains

Poly(2-hydroxyethyl methacrylate) derivatives with amphiphilic side chains composed of polar ester and non-polar alkyl groups (PHEMA#C, #=9, 11, 13, 15, and 17), where # is the number of carbon atoms in the alkyl side groups, were synthesized. In this paper, the influence of ester and alkyl groups on the molecular structure and wettability of the polymers were studied through varying # in the alkyl side groups. PHEMA#Cs with relatively longer alkyl side groups (#≥15) show bilayer lamellar structures with well aligned side chains giving rise to the very low surface energies, calculated from advancing contact angles, in the range of 22.7-22.8 mN/m. In contrast, PHEMA#Cs with shorter alkyl side groups with #≤13 have disordered structures on the polymer surfaces and stick-slip behavior was observed when water was used as the test liquid for the advancing contact angle measurements. Furthermore, the alignment behavior of nematic liquid crystal, 5CB on the PHEMA#C films could be correlated with the molecular structure and wettability of the polymers.     

Photocatalytic production of hydrogen peroxide using polymer bound anthraquinone. I. Photoproducts in 2-hydroxyethyl methacrylate hydrogels swollen with water and 2-propanol

Photoreductions of polymer-bound anthraquinone in degassed water- and 2-propanolswollen 2-hydroxyethyl methacrylate hydrogel films were performed at 313 and 334 nm, and in sunlight for the water-swollen system. The quantum yield at 334 nm for production of anthrahydroquinone was 0.31 in water and 0.94 in 2-propanol. Results at 313 nm were very similar. A reversible oxygen insensitive side product, indentified as 10-hydroxyanthrone, was produced simultaneously to the anthrahydroquinone in water-swollen films, but not for 2-propanol. A small amount of irreversible side product, believed to be hydroxylated anthraquinone, was also formed in the water system. A photochemical reaction scheme is suggested to account for these observations. Hydrogen peroxide production from photoreduction-reoxidation cycling of the hydrogels is reported.     

Study of the miscibility of poly(styrene-co-4-vinylbenzoic acid) with poly(ethyl methacrylate) or with poly[ethyl methacrylate-co-(2-N,N-dimethylaminoethyl) methacrylate] by inverse gas chromatography

Poly(styrene) is immiscible with poly(ethyl methacrylate). The introduction of a small amount of 4-vinylbenzoic acid units along poly(styrene) chains (PS-VBA) enhanced its miscibility with poly(ethyl methacrylate) (PEMA) or with poly[ethyl methacrylate-co-(2-N,N-dimethylaminoethyl) methacrylate] (PEMA-DAE), as observed from the appearance of a single composition dependent glass transition temperature for each binary system using inverse gas chromatography. The negative values of the apparent polymer-polymer interaction parameter, chi(23)app, determined with different families of molecular probes, for three blend compositions and over a range of temperature confirm quantitatively the miscibility of these blends. The chi(23)app values for PEMA(PS-VBA) and (PEMA-DAE)-(PS-VBA) blends are dependent of the chemical nature of the probes, the temperature and the blend composition.     

Evaluation of physicochemical properties on the blending process of pharmaceutical granules with magnesium stearate by thermal effusivity sensor

Magnesium Stearate (MgSt) is a widely used lubricant for preventing tablet compression trouble. It is known that the powder characteristic of MgSt is different among MgSts manufactured by different methods and conditions. These differences affect blending efficiency with pharmaceutical additives. The purpose of this study is to evaluate the physicochemical properties of MgSt by thermal effusivity sensor for in-process monitoring of powder blending. MgSts having different physicochemical properties and granulated sugar spheres were used for model excipients. V-blender was used for powder blending. Thermal effusivity values of each of the ingredients in the blend were measured using one of the sensors prior to placing the ingredient in the blender. The effect of magnesium stearate addition to uniform ingredients can be clearly identified using the sensors. Compared to effusivity data and powder density, effusivity data correlated with the powder characteristics of magnesium stearate. These results suggested that effusivity can be used for end point detection of blending process for various magnesium stearates with sugar sphere. When various magnesium stearates were added to the granule, required time for achieving homogeneous powder blend was different. Blending behavior would be affected by the physicochemical characters. Blend uniformity and blended states of granules containing magnesium stearate can be detected nondestructively without intricate sampling process. Thermal effusivity sensors are an efficient tool to monitor the real time blending behavior of pharmaceutical ingredients.     

Structure and properties of cellulose graft copolymers. III. Cellulose–methyl methacrylate graft copolymers synthesized by the ceric ion method

The ceric ion-initiated graft copolymerization of methyl methacrylate onto wood cellulose was found to depend on the concentrations of initiator, monomer, and cellulose. The structure of cellulose—methyl methacrylate graft copolymers was studied by hydrolyzing away the cellulose backbone to isolate the grafted poly(methyl methacrylate) branches. The molecular weights and molecular weight distributions of the grafted poly(methyl methacrylate) were determined by using gel-permeation chromatography. The number-average (M?_n) molecular weights ranged from 36 000 to 160 000 and the polydispersity ratios (M?_w/M?_n) varied from 4.0 to 7.0. The grafting frequency or the number of poly(methyl methacrylate) branches per cellulose chain calculated from the per cent grafting and molecular weight data varied from 0.38 to 3.2. The structure of cellulose—methyl methacrylate graft copolymers and the effect of stepwise addition of initiator on the structure are discussed.     

The reactions of non-gem-hexanedioxytetrachlorocyclotriphosphazene with 2-(2-hydroxyethyl)thiophene,benzyl alcohol and 1,1,3,3-tetramethylguanidine. Spectroscopic studies of the derived products

Abstract

Reactions of non-gem-hexanedioxytetrachlorocyclotriphosphazene (1) with monofunctional nucleophilic reagents, 2-(2-hydroxyethyl)thiophene (2), benzyl alcohol (3) and 1,1,3,3-tetramethylguanidine (4) were investigated. The reactions, using an excess of NaH, in THF solutions, under refluxing conditions and with 1:2?mole ratios allow the synthesis of the following novel cyclotriphosphazene derivatives: 2,4-dichloro-2,4-(hexane-1,6-dioxy)-6,6-[2-(2-ethoxy)hiophene]-cyclotriphosphazatriene, N₃P₃Cl₂[O(CH₂)₆O-(C₆H₈OS)₂] (5); 2,4-(hexane-1,6-dioxy)-2,4,6,6-[2-(2-ethoxy) thiophene]-cyclotriphosphazatriene, N₃P₃[O(CH₂)₆O-(C₆H₈OS)₄] (6); 2,4-dichloro-2,4-(hexane-1,6-dioxy)-6,6-(methoxybenzene)-cyclotriphosphazatriene, N₃P₃Cl₂[O(CH₂)₆O-(C₆H₅CH₂O)₂] (7); 2,4-(hexane-1,6-dioxy)-2,4,6,6-(methoxybenzene)-cyclotriphosphazatriene, N₃P₃[O(CH₂)₆O-(C₆H₅CH₂O)₄] (8); and 2,4-dichloro-2,4-(hexane-1,6-dioxy)-6,6-(1,1,3,3-tetramethyguanidine)-cyclotriphosphazatriene, N₃P₃Cl₂[O(CH₂)₆O-HN-CN₂(CH₃)₄] (9). The structures of the synthesized compounds (5–9) have been characterized by elemental analysis, TLC-MS, ¹H, ¹³C and ³¹P {+¹H} and {?¹H} NMR spectral data.     

Granulation of core particles suitable for film coating by agitation fluidized bed I. Optimum formulation for core particles and development of a novel friability test method

To prepare powdered medicines without bitter taste, film coating is required to cover the surface of core particles. In this study, effect of formulation and operating conditions of agitation fluidized bed on the core particle properties was investigated. In order to prevent breakage of the core particles during coating process, which sometimes causes variation of drug dissolution rate, addition of maltose syrup powder during the formulation process of the core particles was investigated. Also, a method for friability test in which the core particles were subjected to strong impact was proposed to evaluate strength of the core particles. The friability of the core particles determined by this test method correlated well with the actual friability of the particles during the coating process. Based on this result, we confirmed this novel friability test method could predict the core particle endurance during the coating process.