Ni-M/SiO2催化1,4-丁炔二醇加氢的金属助剂效应

以SiO₂气凝胶为载体,采用等体积浸渍法制备了Ni/SiO₂及不同金属助剂改性的Ni-M/SiO₂（M=Fe、Co、Cu）催化剂,利用ICP、BET、XRD、H₂-TPR、H₂-TPD等手段对催化剂进行了表征,考察了不同第二金属对催化剂结构与1,4-丁炔二醇加氢性能的影响.结果表明,第二金属与Ni物种具有不同程度的双金属协同效应,其中Cu的加入不仅能够提高Ni活性物种的分散度,而且Ni-Cu双金属间的相互作用改善了NiO物种的还原性能及氢活化能力,有利于氢和1,4-丁炔二醇在活性位点的快速转化.在反应温度50℃,氢压1 MPa,反应时间3 h的加氢评价条件下,15Ni5Cu/SiO₂催化剂不仅可以实现1,4-丁炔二醇的完全转化,而且能够有效降低难分离副产物2-羟基四氢呋喃的含量,具有最优的加氢活性和对1,4-丁烯二醇的选择性.     

钴基催化剂在费-托反应过程中的失活行为

 考察了 Co/SiO₂, Co/Ru/SiO₂ 和疏水改性 Co/Ru/SiO₂ 催化剂在费-托合成过程中的稳定性.结果发现, 随着反应的进行, 三种催化剂都呈现一定程度的失活,它们稳定性高低顺序为: 疏水改性 Co/Ru/SiO₂ > Co/SiO₂ > Co/Ru/SiO₂. Co/SiO₂ 催化剂的失活是由于催化剂上 Co 晶粒的长大和硅酸钴物种的生成, 而 Co/Ru/SiO₂和疏水改性 Co/Ru/SiO₂的失活则是由于催化剂上 Co 晶粒的长大所致. 由于 Co/Ru/SiO₂ 催化剂的 Co 晶粒比 Co/SiO₂催化剂的小得多, 在反应过程中更容易长大, 所以 Co/Ru/SiO₂催化剂稳定性更差; 而疏水改性 Co/Ru/SiO₂催化剂表面的疏水性既抑制了硅酸钴物种的形成, 又使 Co 晶粒长大较慢, 因此其稳定性最高.     

选择氧化物载体调变乙醇重整和1,3-丁二烯加氢反应双金属催化剂

研究了不同载体负载的Pt-Ni双金属和单金属催化剂上乙醇重整和1,3-丁二烯加氢反应性能, 以考察氧化物载体对双金属结构和催化活性的影响. 所用的氧化物载体包括γ-Al₂O₃, SiO₂, TiO₂, CeO₂以及高比表面积(HSA)和低比表面积(LSA)ZrO₂. 采用共浸渍法制备催化剂, 用CO化学吸附、透射电镜和扩展X射线吸收精细结构光谱进行催化剂表征, 采用傅里叶变换红外间歇反应器进行化学反应评价. 对于乙醇重整反应, Pt-Ni双金属催化剂优于单金属催化剂, Pt-Ni双金属催化剂活性顺序为TiO₂ > SiO₂ > γ-Al₂O₃ ≈ LSA-ZrO₂ > CeO₂ > HSA-ZrO₂. 对于1,3-丁二烯加氢反应, 在SiO₂, TiO₂和HSA-ZrO₂载体上双金属催化剂优于单金属催化剂, Pt-Ni双金属催化剂活性顺序为SiO₂ > CeO₂ > γ-Al₂O₃ > LSA-ZrO₂ > HSA-ZrO₂ ≈ TiO₂.     

催化剂载体对CVD法制备碳纳米管的影响

用DTA、TEM和XRD方法研究了碳氢化合物催化裂解制备碳纳米管(CNTs)反应中催化剂载体的影响。实验结果表明:当以金属Co作为活性组分时,对于催化剂Co/Al₂O₃,在最佳反应温度(650℃)条件下,碳纳米管粗产品的产率为457g/100g·cat,明显高于以Co/SiO₂作载体时的产率131g/100g·cat,且碳纳米管直径小,直径分布范围窄(10nm～20nm)。但在空气气氛中的DTA结果表明,在催化剂Co/SiO₂上生成的碳纳米管的抗氧化能力较在催化剂Co/Al₂O₃上生成的碳纳米管强。通过TEM和XRD方法进一步研究发现:反应过程中,催化剂Co/Al₂O₃中的Co微晶粒度随反应温度升高(从650℃到750℃)而增大(从15.8nm到16.7nm)的速率小于催化剂Co/SiO₂中的Co微晶粒度随反应温度升高而增大(从11.0nm到13.4nm)的速率;相应地,在催化剂Co/Al₂O₃上生成的碳纳米管的(外)直径随反应温度升高而增大的速率(从10～20nm到20～25nm)亦小于在催化剂Co/SiO₂上生成的碳纳米管的(外)直径随反应温度升高而增大的速率(从10～30nm到30～50nm)。     

Ni/SiO2-ZrO2催化剂焙烧温度对其催化愈创木酚加氢脱氧性能的影响简

采用化学沉淀法合成了SiO₂-ZrO₂复合氧化物载体,并以浸渍法制备了Ni/SiO₂-ZrO₂双功能催化剂,考察了焙烧温度对催化剂结构及其催化愈创木酚加氢脱氧制环己烷性能的影响. 结果表明,经500℃焙烧催化剂的加氢脱氧活性最高,在Ni金属中心和SiO₂-ZrO₂载体材料的协同作用下,愈创木酚转化率为100%,环己烷选择性为96.8%. 对催化剂进行N₂物理吸附、H₂化学吸附、X射线衍射分析、H₂程序升温还原、NH₃程序升温脱附与Raman光谱等表征后发现,合成的SiO₂-ZrO₂为无定形的酸碱两性氧化物;经500℃焙烧的催化剂样品的有效比表面积和孔体积均明显增大,表面酸量最多,硝酸镍分解成小颗粒的NiO较易被H₂还原,这些特性是该催化剂样品具有高效加氢脱氧活性的原因.     

H2S预处理对Ni2P/SiO2催化剂结构及氯苯加氢脱氯性能的影响

采用10% H₂S/H₂对Ni₂P/SiO₂催化剂进行预处理,利用X射线衍射、电感耦合等离子发射光谱、X射线光电子能谱、CO化学吸附、H₂程序升温脱附、NH₃程序升温脱附及活性评价等方法研究了H₂S预处理对催化剂结构和氯苯加氢脱氯反应性能的影响.结果表明,即使在873K进行H₂S预处理,Ni₂P/SiO₂催化剂体相结构及Ni₂P晶粒大小没有发生变化,但导致Ni₂P晶粒表面形成了磷硫镍相(NiP_xS_y),同时使表面溢流氢数量增加.硫物种的存在不仅阻塞了部分镍中心,使催化剂表面镍中心密度降低,也导致镍中心的缺电子性进一步增加.经H₂S预处理后Ni₂P/SiO₂催化剂上氯苯加氢脱氯反应的转化频率(TOF)明显提高,这可能与催化剂表面Ni物种的缺电子性增强及溢流氢数量增多有关.     

镍基催化剂：制备及水相催化糠醛加氢脱氧反应性能

以SiO₂-Al₂O₃、γ-Al₂O₃为载体采用浸渍法制备了不同负载量的镍基催化剂,以XRD、H₂-TPR、NH₃-TPD与低温N₂吸附等技术对催化剂特性进行了表征,并进行了水相催化糠醛加氢脱氧实验研究以制备以C₅为主要成分的生物汽油。重点考察了催化剂的镍负载量、载体种类及反应温度对糠醛转化率、目标产物C₅选择性的影响,并对催化剂的重复利用性能和糠醛水相加氢脱氧反应机理进行了探讨。结果表明,Ni/SiO₂-Al₂O₃催化性能明显优于Ni/γ-Al₂O₃。在140 ℃、氢冷压3.0 MPa的优化反应条件下,14wt% Ni/SiO₂-Al₂O₃催化糠醛反应的转化率为63%,C₅选择性高达93%。升高反应温度可以提高糠醛的转化率,但反应产物的选择性降低。催化剂在第3次重复使用时糠醛的转化率明显降低,催化剂表面有明显的残留有机聚合物和积碳,达到25wt%左右。     

Cu对Ni-Cu/SiO2催化1,4-丁炔二醇加氢性能的影响

采用超临界干燥法和等体积浸渍法制备了不同Ni/Cu比例的Ni-Cu/SiO₂双金属催化剂,利用ICP、BET、XRD、H₂-TPR、H₂-TPD、NH₃-TPD等手段对催化剂进行了结构表征,考察了不同Ni/Cu比例对催化剂结构以及1,4-丁炔二醇加氢性能的影响.结果表明,少量Cu的引入不仅能够提高Ni活性物种的分散性,而且Ni-Cu双金属间的相互作用改善了NiO物种的还原性能及氢活化能力,有利于氢和1,4-丁炔二醇在活性位点的快速转化.在反应温度50℃,氢压1 MPa,反应时间3 h的加氢评价条件下,Ni/Cu比为3：1时,15Ni5Cu/SiO₂催化材料不仅可以实现BYD的完全转化,而且能够有效降低难分离副产物2-羟基四氢呋喃的含量,具有最优的加氢活性和对1,4-丁烯二醇及1,4-丁二醇的选择性.     

Ni/SiO2-Al2O3催化乙酰丙酸加氢制γ-戊内酯

采用溶胶-凝胶法制备了一系列不同Al₂O₃含量的SiO₂-Al₂O₃复合氧化物,以该系列复合氧化物为载体,采用等体积浸渍法制备了Ni负载量15%（重量百分比）的催化剂,用于催化乙酰丙酸加氢制γ-戊内酯.采用N₂物理吸附、X射线衍射（XRD）、H₂程序升温还原（H₂-TPR）、H₂程序升温脱附（H₂-TPD）、NH₃程序升温脱附（NH₃-TPD）和吡啶吸附红外（Py-IR）等手段对催化剂进行了表征.结果表明,不同载体催化剂的活性组分分散度及表面酸性质存在明显差异,显著影响了催化剂吸附、活化H₂与C=O键的能力,进而影响了催化剂的乙酰丙酸加氢活性.其中,Ni/SiO₂-Al₂O₃催化剂上的L酸中心能够促进C=O键的吸附、活化,与金属Ni上的H₂吸附活性位协同作用,大大提高了乙酰丙酸加氢活性.因此,具有最多L酸中心和丰富H₂吸附活性位的Ni/SiO₂-8Al₂O₃催化剂表现出最高的乙酰丙酸加氢活性,在180℃、4 MPa氢气压力下,乙酰丙酸转化率达到90.5%,目标产物γ-戊内酯选择性为100%.     

Ce助剂对V/SiO2催化CO2氧化乙苯脱氢性能的影响

通过N₂吸附、X射线衍射(XRD)、X射线光电子能谱(XPS)、H₂程序升温还原(H₂-TPR)、CO₂程序升温脱附(CO₂-TPD)和热重分析(TGA)等多种表征手段和催化反应性能评价,研究了铈助剂的添加对V/SiO₂催化CO₂氧化乙苯脱氢性能的影响. 结果表明,Ce助剂不仅提高了催化剂活性组分分散性和氧化还原性能,抑制了钒物种的深度还原,而且增强了催化剂碱性和CO₂吸附能力,减缓了积炭生成,从而显著提高了V-Ce/SiO₂对CO₂氧化乙苯脱氢反应的催化活性和稳定性. 在本实验中,V(0.8)-Ce(0.25)/SiO₂催化剂表现出最佳的催化性能,苯乙烯(ST)收率可达55.6%,选择性为98.5%,反应12 h 后,催化剂活性基本不变,与惰性N₂气氛比较,CO₂明显促进了乙苯脱氢反应,归因于CO₂能保持催化剂表面钒物种的高价态.     

Preparation of Cu/SiO2 Catalyst by Solution Exchange of Wet Silica Gel

Structural formation process of Ni/SiO₂ and Cu/SiO₂ catalysts prepared by solution exchange of wet silica gel was investigated. Microstructures of Cu/SiO₂ and Ni/SiO₂ were quite different from each other. In the case of Cu/SiO₂, Cu particles with diameter of ca. 3–5 nm dispersed homogeneously at less Cu content, and the particle size of Cu as well as pore size of silica gel support increased with increasing Cu content. In the Ni/SiO₂, the Ni particles with diameter of ca. 6–10 nm gathered densely to form aggregates in silica matrix resulting in sea-island structure, whereas the size of Ni particle slightly increased with increasing Ni content. The difference in the structure of the metal-silica composites is probably caused by the difference in interaction between silica gel network and metal ions during drying and heating processes.     

Monolayer oxide catalysts from alkoxide precursors, part IV. Vanadia, titania and stibia on SiO2, SnO2, and TiO2 in 2-propanol oxidation

Vanadia monolayer catalysts supported on SnO₂, ZrO₂, TiO₂, and SiO₂, similarly as titania and stibia monolayers deposited on SiO₂, have been synthesized by reacting the corresponding metal alkoxides with hydroxyls on the carrier surfaces. The metal ions loads in monolayer systems were determined. The catalysts activity was tested in 2-propanol transformations. The nature of carrier has a strong influence on the dehydrating to dehydrogenating activity ratio of vanadia monolayer.     

Co或Ni促进的Cu/SiO2-Al2O3催化剂上丙三醇和苯胺气相合成3-甲基吲哚

对丙三醇和苯胺在Co或Ni促进的Cu/SiO2-Al2O3催化剂上气相合成3-甲基吲哚进行了研究.采用N2吸附、氢气程序升温还原(H2-TPR)、电感耦合等离子体(ICP)发射光谱、X射线衍射(XRD)、透射电子显微镜(TEM)、氨程序升温脱附(NH3-TPD)及热重(TG)分析等技术对催化剂进行了表征.结果表明,向Cu/SiO2-Al2O3催化剂加入钴或镍助剂改善了催化剂的催化性能,钴比镍更加有效.在催化剂Cu-Co/SiO2-Al2O3和Cu-Ni/SiO2-Al2O3上,反应第3 h,3-甲基吲哚收率分别达到47%和45%,而且催化剂经过6次再生收率仍能达到44%和42%.各种表征表明,向Cu/SiO2-Al2O3催化剂加入钴或镍助剂能增强铜和载体之间的相互作用,其结果不仅促进了铜粒子在载体表面的分散度,而且有效减少了反应过程中铜组分的流失.另外,加入钴或镍助剂还能减少催化剂的中强酸中心数,从而提高3-甲基吲哚的选择性,并且抑制积炭的形成.此外,钴助剂还能增加催化剂的弱酸中心数,促进3-甲基吲哚的生成.提出了金属铜与弱酸中心共同促进3-甲基吲哚合成的催化反应机理.     

Preparation and characterization of CuO/SiO2 and NiO/SiO2 with bimodal pore structure by sol-gel method

CuO/SiO₂ and NiO/SiO₂ with bimodal pore structure were prepared by sol-gel reactions of Tetra-methoxysilane (TMOS) and the respective metal nitrate in the presence of poly (ethylene oxide) (PEO) with an average molecular weight of 10 000 and the catalyst of acetic acid. In this process, the interconnected macroporous morphology was formed when transitional structures of spinodal decomposition were frozen by the sol-gel transition of silica. The addition of copper and nickel into the silica-PEO system had a negligible effect on the morphology formation. In gel formation, it was found that NiO crystalline sizes in the samples increased with decreasing Si/Ni molar ratio. It was considered that PEO interacted with both silica and nickel cations. In the CuO/SiO₂ with the presence of PEO_, CuO crystalline sizes were larger than those of NiO/SiO_2. It was considered that there was no obvious interaction between the Cu cation and PEO, most of the copper ions in wet silica gel were present in the outer solution. They easily aggregated as copper salts in the drying process of wet gel and decomposed into CuO particles in heating. While in the CuO/SiO₂ with the absence of PEO, the Cu was selectively entrapped as small particles in the gel skeleton due to the interaction between Cu aqua complex and silica gel network.     

Carbon Dioxide Reforming of Methane over Ni Catalysts Supported on Al2O3 Modified with La2O3, MgO, and CaO

The preparation of synthesis gas from carbon dioxide reforming of methane (CDR) has attracted increasing attention. The present review mainly focuses on CDR to produce synthesis gas over Ni/MO_x/Al₂O₃ (X = La, Mg, Ca) catalysts. From the examination of various supported nickel catalysts, the promotional effects of La₂O₃, MgO, and CaO have been found. The addition of promoters to Al₂O₃-supported nickel catalysts enhances the catalytic activity as well as stability. The catalytic performance is strongly dependent on the loading amount of promoters. For example, the highest CH₄ and CO₂ conversion were obtained when the ratios of metal M to Al were in the range of 0.04–0.06. In the case of Ni/La₂O₃/Al₂O₃ catalyst, the highest CH₄ conversion (96%) and CO₂ conversion (97%) was achieved with the catalyst (La/Al = 0.05 (atom/atom)). For Ni/CaO/Al₂O₃ catalyst, the catalyst with Ca/Al = 0.04 (atom/atom) exhibited the highest CH₄ conversion (91%) and CO₂ conversion (92%) among the catalysts with various CaO content. Also, Ni/MgO/Al₂O₃ catalyst with Mg/Al = 0.06 (atom/atom) showed the highest CH₄ conversion (89%) and CO₂ conversion (90%) among the catalysts with various Mg/Al ratios. Thus it is most likely that the optimal ratios of M to Al for the highest activities of the catalysts are related to the highly dispersed metal species. In addition, the improved catalytic performance of Al₂O₃-supported nickel catalysts promoted with metal oxides is due to the strong interaction between Ni and metal oxide, the stabilization of metal oxide on Al₂O₃ and the basic property of metal oxide to prevent carbon formation.     

Synthesis characterization and catalytic evaluation of Ni/ZrO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> aerogels catalysts

The Ni/ZrO₂/SiO₂ aerogels catalysts were synthesized via three different routes: (i) impregnation ZrO₂–SiO₂ composite aerogels with a aqueous solution of Ni(NO₃)₂, (ii) impregnation SiO₂ aerogels with a mixed aqueous solution of Ni(NO₃)₂ and ZrO(NO₃)₂ · 2H₂O, (iii) one-pot sol–gel procedure from precursors Ni(NO₃)₂/ZrO(NO₃)₂ · 2H₂O/Si(OC₂H₅)₄. These catalysts were characterized by X-ray diffraction (XRD), temperature-programmed reduction (TPR), ammonia temperature-programmed desorption (NH₃-TPD), N₂ adsorption–desorption isotherms and Fourier transform infrared (FT-IR). The Liquid-phase hydrogenation of maleic anhydride (MA) was performed over these catalysts. The results revealed that the different preparation routes result in a difference between the obtained samples, concerning the crystal structure and composition, surface acidity, mixed level of each component, texture, and catalytic selectivity.     

Characterization and catalytic behavior of silica-supported copper catalysts prepared by impregnation and ion-exchange methods

Two kinds of Cu/SiO₂ catalysts were prepared by impregnation (IM) and ion-exchange (IE) methods, and tested in dehydrogenation of 2-butanol to methyl-ethyl-ketone. Some kinds of Cu²⁺ on the IE catalyst could not be reduced during the reaction, and it produced the butene. The copper oxide over the IM catalyst could be reduced during the reaction, and showed stable dehydrogenation activity for 2-butanol.     

Formation and Crystallization Behavior of Gels in the Na2O-SiO2-TiO2-ZrO2 System

SiO₂-TiO₂-ZrO₂ and 5Na₂O·95(SiO₂ + TiO₂ + ZrO₂) gels were synthesized and role of Na₂O in gel formation and crystallization behavior of gels were studied. From Si(OC₂H₅)₄, Ti(iso-OC₃H₇)₄, Zr(n-OC₃H₇)₄ and NaOCH₃ solutions in EtOH without H₂O, transparent and opaque gels were obtained. Opaque bulk gels, rich in TiO₂ or ZrO₂ composition in Na₂O containing SiO₂-TiO₂-ZrO₂ system, contain agglomerated spherical particles of diameter small <10 m, in contrast with opaque gels having large particles <30 m in alkali-free SiO₂-TiO₂-ZrO₂ system. Crystallization temperature (Tc) was measured by DTA on dried gels. Compared with the alkali-free SiO₂-TiO₂-ZrO₂ gels, 5 mol% Na₂O containing gels gave lower Tc in SiO₂ rich compositions and higher in TiO₂ rich or ZrO₂ rich compositions.     

Calorimetric Characterization of Surface Reactivity of Supported Ga2O3 Catalysts

The surface properties of supported gallium oxide catalysts prepared by impregnation of various supports (γ-Al₂O₃, SiO₂, TiO₂, ZrO₂) were investigated by adsorption microcalorimetry, using ammonia and water as probe molecules. In the case of acidic supports (γ-Al₂O₃, ZrO₂, TiO₂), the acidic character of supported gallium catalysts always decreased in comparison with gallium-free supports; on very weakly acidic SiO₂, new acidic centers were created when depositing Ga₂O₃. The addition of gallium oxide decreased the hydrophilic properties of alumina, titania and zirconia, but increased the amount of water adsorbed on silica. The catalytic performances in the selective catalytic reduction of NO by C₂H₄ in excess oxygenwere in the order Ga/Al₂O₃>Ga/TiO₂>Ga/ZrO₂>>Ga/SiO₂. This order is more related to the quality of the dispersion of Ga₂O₃ on the support than to the global acidity of the solids. This revised version was published online in July 2006 with corrections to the Cover Date.     

Methane steam reforming over rhodium promoted Ni/Al2O3 catalysts

The effect of Rh addition upon catalyst characteristics and performance in methane steam reforming was investigated using Rh-promoted Ni/Al₂O₃ catalysts. The number of reduced metal atoms exposed on the surface increased for the Rh-promoted catalysts. Rh-promoted catalysts showed an increase in CH₄ reforming activity; however, constant turnover frequencies for promoted and unpromoted catalysts suggest that the increase in the number of metal surface atoms caused the activity enhancement. Rh also facilitated reduction of Ni/Al₂O₃.