Ultra-trace analysis of nitrite in food samples by flow injection with spectrophotometric detection

A flow injection system with spectrophotometric detection is proposed for the determination of low levels of nitrite based on its catalytic effect on the oxidation of gallocyanine by bromate in acidic media. Various analytical parameters such as acidity, reagent concentration, flow rate, sample size, time, temperature, and interfering species were studied. The calibration graph was linear for 0.020–0.500 μg/mL of nitrite. The method is successfully applied to food samples. Up to 30 ± 5 samples can be analyzed per hour. Received: 8 April 1998 / Revised: 3 June 1998 / Accepted: 31 July 1998     

Design of a field flow system for the on-line spectrophotometric determination of phosphate, nitrite and nitrate in natural water and wastewater

This study describes the design and optimisation of a field flow system for the in-situ collection and on-line determination of phosphate, nitrate and nitrite by flow injection analysis-spectrophotometry. The method is based on the initial determination of phosphate as its phosphoantimonylmolybdenum blue complex which is then oxidized on-line by nitrite and the decrease in absorbance is monitored at 880 nm. Nitrate is determined as the difference between total and initial nitrite content in a separate flow after reduction to nitrite in a cadmium reductive column. The calibration curves were linear in the range 0–2.00 mg L⁻¹ P-phosphate, 0–10.00 mg L⁻¹ nitrite and 0–7.00 mg L⁻¹ nitrate with correlation coefficients of 0.9979, 0.9993 and 0.9995, respectively. The detection limits, calculated as 3S/N, were 0.15 mg L⁻¹ for P-phosphate, 0.17 mg L⁻¹ for nitrite and 0.09 mg L⁻¹ for nitrate. The reproducibility was below 3.0% (n = 7). Method validation in the analysis of natural water and wastewater samples revealed that it can efficiently be applied to the determination of the target analytes, with recoveries in the range of 92–108%. Correspondence: Athanasios G. Vlessidis, Laboratory of Analytical Chemistry, Department of Chemistry, University of Ioannina, Ioannina 45110, Greece     

FI spectrophotometric determination of Pd with DBOK-chlorophosphonazo

A flow injection method was developed for the determination of palladium, based on the reaction of palladium with DBOK-chlorophosphonazo with a detection limit of 0.07 μg/mL and a linear calibration range from 0.1 to 3.2 μg/mL of palladium. The reaction product has a maximum absorption at 630 nm. The method was applied to determine Pd²⁺ in catalysts and in anode mud samples. The relative error is less than 3% and the recovery of palladium is in the range 95% to 105% Received: 27 April 1998 / Revised: 24 August 1998 / Accepted: 26 August 1998     

FI spectrophotometric determination of Pd with DBOK-chlorophosphonazo

A flow injection method was developed for the determination of palladium, based on the reaction of palladium with DBOK-chlorophosphonazo with a detection limit of 0.07 μg/mL and a linear calibration range from 0.1 to 3.2 μg/mL of palladium. The reaction product has a maximum absorption at 630 nm. The method was applied to determine Pd²⁺ in catalysts and in anode mud samples. The relative error is less than 3% and the recovery of palladium is in the range 95% to 105% Received: 27 April 1998 / Revised: 24 August 1998 / Accepted: 26 August 1998     

Determination of nitrite and bromate in disinfected water samples at the low μg/L level by means of a high-capacity anion exchanger

Bromate and nitrite are formed during the disinfection of water. The German threshold value for nitrite in drinking water is 100 μg/L, for bromate a limit below 50 μg/L has to be established. A self-made high-capacity resin with 2-(dimethylamino)-ethanol functionality in combination with a UV-transparent elution system based on perchloric acid allows the separation and sensitive photometric detection of nitrite and bromate, even if high chloride concentrations are present. The high capacity of the strongly basic resin allows sample volumes of up to 400 μL without disturbance of the separation. Detection limits for bromate and nitrite are 15 and 10 μg/L, respectively. The direct analysis of water samples with high salt contents, such as disinfected pool water, is possible by insertion of an on-line chloride removal step. Received: 30 September 1996 / Revised: 20 December 1996 / Accepted: 28 December 1996     

Selective voltammetric determination of chromium (VI) with DTPA and nitrate

A voltammetric determination of Cr(VI) in a flow system is described based on the selective accumulation of the reduction product of Cr(VI) on an HMDE, its complexation with DTPA and subsequent reduction of the complex in presence of nitrate. The calibration graphs were linear up to 100 and 5 nmol/L for deposition times 120 and 600 s, respectively. The relative standard deviation was 2.8% (n = 5) for Cr(VI) concentrations of 5 × 10^–8 mol/L. The detection limits (3 σ) for Cr(VI) were 1.0 and 0.12 nmol/L at deposition times of 120 and 600 s, respectively. Typical interferences derived from real water samples are discussed. The method has been applied for the determination of Cr(VI) in spiked natural water samples. Received: 18 June 1998 / Revised: 28 September 1998 / Accepted: 5 October 1998     

Determination of Cr(III) in urine, blood serum and hair using flow injection chemiluminescence analysis

A flow injection (FI) chemiluminescence method for the determination of Cr(III) in blood serum, urine and hair samples is reported. It is based on the chromium-catalyzed light emission from the luminol oxidation by hydrogen peroxide. The apparatus consists of an FI system with a flow cell formed by a coiled transparent tube suitable for chemiluminescence detection. The specificity of the method is achieved in presence of EDTA. The detection limit under optimum conditions is 0.01 μg L^–1 of Cr(III). Precision and accuracy were evaluated by determining Cr(III) concentrations in urine standards from the National Institute of Standard and Technology (NIST). Received: 30 June 1997 / Revised: 16 January 1998 / Accepted: 23 January 1998     

Preconcentration technique for manganese by adsorption onto a tantalum wire for tungsten tube atomizer electrothermal atomization atomic absorption spectrometry

A multi-pumping flow system for the spectrophotometric determination of nitrite and nitrate is described. The determination of nitrite is based on the Griess-Ilosvay reaction. Nitrate can be determined after its on-line reduction to nitrite using hydrazine sulphate in alkaline medium. Calibration was linear up to 3 mg NO₂ ⁻ L⁻¹ with a limit of detection (3s_b/S) of 0.013 mg NO₂ ⁻ L⁻¹ an injection throughput of 55 injections h⁻¹ and a repeatability (RSD) of 0.5% for the direct determination of nitrite. Two calibration graphs within the ranges 0.039–7 mg NO₃ ⁻ L⁻¹ and 0.026–5 mg NO₂ ⁻ L⁻¹ were run for the determination of nitrate and nitrite under reducing conditions, respectively. A limit of detection of 0.039 mg NO₃ ⁻ L⁻¹ was obtained. An injection throughput of 27 injections h⁻¹ and an RSD lower than 1.5% were achieved. The method was successfully applied to the determination of nitrite and nitrate in water samples. Correspondence: Víctor Cerdà, Department of Chemistry, University of the Balearic Islands, Carretera de Valldemossa Km7.5, 07122 Palma de Mallorca, Spain     

Direct multiparametric determination of anions in soil samples by integrating on-line automated extraction/filtering with capillary electrophoresis

An integrated continuous flow-capillary electrophoresis for the determination of soluble anions in soil samples is presented. A filtration probe coupled with the flow system, which is located before the capillary electrophoresis instrument, was designed to simplify sample pretreatment and to perform clean-up of aqueous soil suspensions. Only the manual weighing of the samples is needed. The extraction process for soil samples was optimized. The clear filtrate containing the soluble anions from soil was then passed to the capillary electrophoresis equipment by a home-made programmable arm. Chloride, sulfate, nitrite and nitrate were determined in soil samples at μg g^–1 level and the results compared to manual reference methods. The precision expressed as relative standard deviation was in the range of ± 1.6 to ± 2.5% for the set of analytes determined. The procedure is up to 4 times faster than the competitive manual methods. Received: 29 July 1997 / Revised: 10 September 1997 / Accepted: 13 September 1997     

An integrated reaction-retention and spectrophotometric detection flow system for the determination of nickel

An integrated flow-through photometric sensor for the determination of nickel in real samples of various origins has been developed. The sensor is based on the reaction of Ni(II) with 1-(2-pyridylazo)-2-naphthol (PAN) immobilized on a cationic resin which was placed in a flow-cell using a spectrophotometer tuned at 566 nm as detector. The Ni(II) ion from the sample injected into the carrrier stream (pH = 5.0) of a monochannel continuous flow system reacts with the immobilized chromogenic reagent to form a red chelate which remains on the active solid support and generates the analytical signal. When this reached its maximum value the Ni(II)-PAN chelate was destroyed using 1 M H₂SO₄ as eluents, leaving the sorbed PAN untouched. The response of the sensor was linear in the three concentration ranges assayed: 0.3–4.0, 0.1–1.6 and 0.05–0.8 μg mL^–1 for sample volumes of 100, 400 and 800 μL, respectively, and the R.S.D.(%) (n = 10) were 1.80(100 μL), 3.04(400 μL) and 2.29(800 μL). The sensor showed an excellent selectivity which could also be increased with a simple on-line modification to avoid interference from copper. It was applied to a variety of real samples with very good results in all cases. Received: 15 April 1998 / Revised: 29 June 1998 / Accepted: 3 July 1998     

Sensitive reaction rate method for the determination of low levels of formaldehyde with photometric detection

A simple and rapid method is proposed for the determination of ultra trace amounts of formaldehyde. It is based on the catalytic effect of formaldehyde on the oxidation of Brilliant cresyl blue by bromate. The reaction is monitored photometrically by measuring the decrease in absorbance of the dye. Formaldehyde in the range of 0.005–2.300 μg/mL can be determined with a limit of detection of 0.003 μg/mL. The relative standard deviation for ten replicate measurements of 1.5 μg/mL formaldehyde is 0.1%. The method was used for the determination of formaldehyde in real samples with satisfactory results. Received: 26 May 1998 / Revised: 30 September 1998 / Accepted: 3 October 1998     

Determination of citric acid in soft drinks using flow injection with potentiometric detection

A flow injection analysis (FIA) system with potentiometric detection has been developed for the determination of citric acid in commercial fruit juices using a copper-selective tubular electrode. It consists of the complexation of citrate ion with copper (II) ion, monitoring the free copper (II) concentration. Linear relationships between the potential and log concentrations of citric acid in the range of 1 × 10^–3 mol/L – 1 × 10^–2 mol/L were attained with samples injected in the system without prior treatment. Repeatability was determined by assessing the relative standard deviation for ten replicate injections of different juice samples which varied from 1.2% to 3.0%. The results provided by the automated system were compared with those of an enzymatic conventional method used for the analysis of citric acid in food and a relative deviation of less than 4.0% was found. Recovery trials resulted in values from 97.0% to 101.0%. The system allows a sampling frequency of 60 samples/h. Received: 22 October 1998 / Revised: 14 December 1998 / Accepted: 16 December 1998     

Application of derivative UV spectrophotometry to the simultaneous determination of nitrate and nitrite ions in bath solutions for alkaline black-oxidation of steel

Second order derivative spectrophotometry was applied to the determination of nitrite and nitrate ions in bath solutions for alkaline black-oxidation of steel. The measurements were directly taken after dilution of the samples at λ = 336.4 nm for NO₃ ^– and λ = 390 nm for NO₂ ^–. The method was checked on artificial mixtures and applied to real samples containing approximately 5.5% NaNO₂ and 6% NaNO₃. The results agree well with those obtained by the standard manganometric method. Received: 8 July 1996 / Revised: 24 September 1996 / Accepted: 28 September 1996     

Validation of a high-performance chromatographic method for determination of cefotaxime in biological samples

An analytical method for detecting and quantifying cefotaxime in plasma and several tissues is described. The method was developed and validated using plasma and tissues of rats. The samples were analyzed by reversed phase liquid chromatography (HPLC) with UV detection (254 nm). Calibration graphs showed a linear correlation (r > 0.999) over the concentration ranges of 0.5–200 μg/mL and 1.25–25 μg/g for plasma and tissues, respectively. The recovery of cefotaxime from plasma standards prepared at the concentrations of 25 μg/mL and 100 μg/mL was 98.5 ± 3.5% and 101.8 ± 2.2%, respectively. The recovery of cefotaxime from tissue standards of liver, fat and muscle, prepared at the concentration of 10 μg/g was: 89.8 ± 1.2% (liver), 103.9 ± 6.5% (fat) and 97.8 ± 2.1% (muscle). The detection (LOD) and quantitation (LOQ) limits for plasma samples were established at 0.11 μg/mL and 0.49 μg/mL, respectively. The values of these limits for tissues samples were approximately 2.5 times higher: 0.3 μg/g (LOD) and 1.25 μg/g (LOQ). For plasma samples, the deviation of the observed concentration from the nominal concentration was less than 5% and the coefficient of variation for within-day and between-day assays was less than 6% and 12%, respectively. The method was used in a pharmacokinetic study of cefotaxime in the rat and the mean values of the pharmacokinetic parameters are given. Received: 25 May 1998 / Revised: 27 July 1998 / Accepted: 1 August 1998     

Flow-injection spectrofluorimetric determination of ethylenethiourea

A flow-injection configuration is proposed for the fluorimetric determination of ethylenethiourea. The procedure is based on the inhibitory effect of ethylenethiourea on the oxidation of thiamine to thiochrome by mercury(II). A linear calibration graph was obtained between 0.1 and 2.0 μg mL^–1, with a sampling rate of 40 samples per hour and a relative standard deviation of about 1.11%. The usefulness of the method was tested for the determination of ethylenethiourea residues in water, milk, potatoes, pear, grape and apple. Received: 26 January 1998 / Revised: 6 April 1998 / Accepted: 9 April 1998     

Flow-injection spectrofluorimetric determination of ethylenethiourea

A flow-injection configuration is proposed for the fluorimetric determination of ethylenethiourea. The procedure is based on the inhibitory effect of ethylenethiourea on the oxidation of thiamine to thiochrome by mercury(II). A linear calibration graph was obtained between 0.1 and 2.0 μg mL^–1, with a sampling rate of 40 samples per hour and a relative standard deviation of about 1.11%. The usefulness of the method was tested for the determination of ethylenethiourea residues in water, milk, potatoes, pear, grape and apple. Received: 26 January 1998 / Revised: 6 April 1998 / Accepted: 9 April 1998     

Kinetic Spectrophotometric Determination of Hydrazine with Neutral Red-Nitrite System

 A new kinetic spectrophotometric method for the determination of hydrazine is described. The method is based on the inhibitory effect of hydrazine on the reaction of neutral red with nitrite in acidic media and 28 °C. A product from the reaction of neutral red with nitrite was used to monitor the reaction spectrophotometrically at 352 nm. Hydrazine can be determined in the range 4.7×10⁻⁶∼3.1×10⁻⁵mol/L with a detection limit of 3.1×10⁻⁶mol/L. The method was applied to the determination of hydrazine in water samples. Received July 23, 1999. Revision January 10, 2000.     

Mass spectrometric identification of polychlorinated dibenzothiophenes (PCDBTs) in surface sediments of the River Elbe

HRGC/MS was applied to six sediment samples from River Elbe for the determination of polychlorinated dibenzothiophenes (PCDBTs). Among the studied tri-, tetra- and octa-chlorinated isomers, trichlorinated species were found to be the dominating ones. The estimated concentration levels of the compounds were in the range of approximately 0.02–2 μg/kg dry weight for trichlorinated and 0.1–0.3 μg/kg for octachlorinated species. Tetrachlorinated dibenzothiophenes could not be detected. Received: 7 October 1997 / Revised: 4 February 1998 / Accepted: 9 February 1998     

A nitrate-selective microelectrode based on a lipophilic derivative of iodocobalt(III)salen

The synthesis of iodo{2,2′-[1,2-octadecanediylbis(nitrilomethylidyne)]diphenolato}cobalt is described. Liquid membrane microelectrodes based on this carrier exhibit Nernstian behaviour with a selectivity sequence according to the Hofmeister series: I^– > NO₃ ^– > NO₂ ^– > Cl^– > HCO₃ ^– > AcO^–. The selectivity coefficient of nitrate over nitrite and chloride amounts to –1.6 and –2.7, respectively. The detection limit for nitrate in water amounts to 10^–5.2 mol/L. A nitrate profile measured in a nitrifying biofilm is presented as a practical application. Received: 11 November 1998 / Revised: 22 January 1999 / Accepted: 27 January 1999     

Automated continuous monitoring of drug dissolution process using a flow injection on-line dialysis sampling – solvent extraction separation spectrophotometric system

Inductively coupled plasma optical emission spectrometry (ICP-OES) was used for the element-specific determination of water-soluble organosilicon species separated by high-performance liquid chromatography (HPLC). Leachates from different waste deposit sites were investigated. The polydimethylsiloxane (PDMS) degradation product dimethylsilanediol (DMSD) could be detected in almost all samples in the low mg L^–1 range, and it was furthermore possible to determine trimethylsilanol (TMSOL) in some leachate samples in the μg L^–1 range. TMSOL was additionally analyzed by a method established before (LT-GC/ICP-OES). This study proved the occurrence of silanol compounds in leachates from locations were silicone material is deposited. Received: 10 July 1998 / Revised: 2 November 1998 / Accepted: 5 November 1998