Effect of A-site element on the performance of three-dimensionally ordered macroporous manganese-based perovskite catalyst

Three-dimensionally ordered macroporous manganese-based perovskite catalyst (3DOM AMnO₃, A = Ce, La, Ni) were synthesized by PMMA hard-templating and impregnation method. Physicochemical properties of the samples were characterized by means of various techniques including XRD, BET, SEM, TEM, XPS and H₂-TPR, and their catalytic activities were evaluated by toluene combustion. It was found that the 3DOM AMnO₃ in each of the samples was perovskite in crystal structure, and only the samples possessed a good quality 3DOM architecture with a surface area of 48.8 m²/g. Due to the highest adsorbed oxygen species concentration (O_ads/O_latt = 2.330), the best low-temperature reducibility (The low-temperature reduction peaks of 3DOM CeMnO₃ catalysts occur at 425 °C) and the strong interaction between CeO₂ and MnO_x formed during calcination. The 3DOM CeMnO₃ sample showed lower apparent activation energy (34.51 kJ·mol⁻¹, SV = 15,000 h⁻¹) and the best catalytic activity for toluene combustion, with the reaction temperatures (T50%, and T90%) required for achieving toluene conversions of 50%, and 90% being 100 °C, 172 °C at SV = 15,000 h⁻¹, respectively.     

Effect of surface hydration on the photocatalytic activity of oxide catalysts in the CO oxidation

The effect of the state of hydrated surface of the bulk oxide photocatalysts, TiO₂, CeO₂, and ZnO on the rate of UV-induced oxidation of CO with atmospheric oxygen was studied. The activity of dehydroxylated catalyst samples evacuated at temperatures of >350 °C toward CO photooxidation decreases in the series CeO₂ > ZnO ≈ TiO₂, while that of partially hydrated samples after pretreatment at 20 °C changes in the order TiO₂ > ZnO ≥ CeO₂ ≈ 0. According to the results, the difference in the photocatalytic activity toward CO oxidation on the dehydrated ZnO, TiO₂, and CeO₂ catalysts is attributable to different concentrations of oxygen vacancies, which are formed more readily after high-temperature treatment on ZnO and CeO₂ and thus promote higher rate of CO photooxidation. Using a new technique for recording transmittance IR spectra, it was found that photoirradiation in the presence of adsorbed water and O₂ gives peroxides and hydroperoxides, with their concentrations decreasing in the series TiO₂ >> ZnO >> CeO₂. Most likely, these species are active intermediates of CO photooxidation with oxygen in the presence of adsorbed water. The hydrophobization effect was detected upon TiO₂ modification with zinc, resulting in removal of surface acid sites capable of adsorbing water. The TiO₂ modification with zinc increases the activity of CO photooxidation with respect to the oxidation catalyzed by samples pretreated at low temperatures (20—60 °C).     

Surface and structural properties of pt/ceo2catalyst under preferential co oxidation in hydrogen (PROX)

Summary Preferential oxidation of CO in the presence of excess hydrogen was studied on Pt/CeO₂with 5% metal loading. Catalytic data were similar to those observed on 1% Pt/CeO₂earlier [16]. The optimum temperature region is T￡373 K; conversion and selectivity of CO oxidation strongly decreased at higher temperatures. High-pressure XPS indicated CO adsorbed on platinum particles and significant amount of water on the ceria surface. The top-most ceria surface re-oxidized as small amount of oxygen (3%) was introduced into the H₂/CO feed. Despite this surface re-oxidation, high-resolution TEM after reaction indicated oxygen deficient ceria bulk structure, in which the defects formed a super-cell, with CeO_1.695structure. The defective ceria is suggested to play an important role stabilizing the hydrogen bonded surface water, which (i) suppresses further hydrogen oxidation and (ii) reacts at the metal/support interface with linearly adsorbed CO in a low temperature water-gas-shift type reaction to produce CO₂.</o:p>     

Construction of Cu-Ce interface for boosting toluene oxidation: Study of Cu-Ce interaction and intermediates identified by in situ DRIFTS

A facile hydrothermal method was applied to gain stably and highly efficient CuO-CeO₂ (denoted as Cu1Ce2) catalyst for toluene oxidation. The changes of surface and inter properties on Cu1Ce2 were investigated comparing with pure CeO₂ and pure CuO. The formation of Cu-Ce interface promotes the electron transfer between Cu and Ce through Cu²⁺ + Ce³⁺ ↔ Cu⁺ + Ce⁴⁺ and leads to high redox properties and mobility of oxygen species. Thus, the Cu1Ce2 catalyst makes up the shortcoming of CeO₂ and CuO and achieved high catalytic performance with T₅₀ = 234 °C and T₉₉ = 250 °C (the temperature at which 50% and 90% C₇H₈ conversion is obtained, respectively) for toluene oxidation. Different reaction steps and intermediates for toluene oxidation over Cu1Ce2, CeO₂ and CuO were detected by in situ DRIFTS, the fast benzyl species conversion and preferential transformation of benzoates into carbonates through C=C breaking over Cu1Ce2 should accelerate the reaction.     

Toluene abatement on Ag-CeO2/SBA-15 catalysts: synergistic effect of silver and ceria

As a typical volatile organic compound, toluene is a hazardous material for human health and the environment, and currently, the development of catalysts for its oxidation into CO₂ and water is crucial. The series of Ag-CeO₂/SBA-15 catalysts is synthesized by wetness impregnation techniques and characterized by a number of physical-chemical methods (nitrogen [N₂] physisorption, small angle X-ray scattering [SAXS], transmission electron microscopy [TEM], and temperature-programmed reduction [TPR]). The toluene sorption and catalytic properties in toluene oxidation are studied. Small silver [Ag] and cerium oxide [ceria, CeO_2] particles with sizes below 3 nm are predominantly formed in the ordered structure of Santa Barbara Amorphous-15 [SBA-15]. The interactions between the Ag and CeO₂ nanoparticles are established. Temperature-programmed desorption of toluene [TPD-C₇H₈] analysis shows that physical adsorption of toluene occurs on pristine SBA-15 material, while the introduction of either silver or ceria to SBA-15 leads to the appearance of additional strongly bound chemisorbed toluene on such sites. When both Ag and CeO₂ are introduced, only chemisorbed toluene is formed over the Ag-CeO₂/SBA-15 catalyst, and the highest catalytic activity in toluene oxidation is observed over this catalyst (T_98% = 233 °C, 0.2% C₆H₅CH₃) that is attributed to the synergistic effect of ceria [CeO_2] and silver [Ag].     

非晶态ZrO_2镶嵌的超细CeO_2催化HCl氧化

采用不同方法制备了铈锆复合氧化物催化剂用于催化HCl氧化反应。自发沉积策略制备的CeO_2@ZrO_2催化剂中,超细CeO_2纳米粒子均匀的镶嵌于非晶态ZrO_2中。CeO_2粒子显著的"尺寸效应"使得该催化剂具有更高的Ce~(3+)和氧空位浓度,而较高的Ce~(3+)和氧空位浓度使得催化剂具有优异的低温氧化还原性能和储释氧能力。催化性能测试表明,CeO_2@ZrO_2催化剂展现出最好的催化活性(1.90 gCl2·gcat~(-1)·h~(-1)),同时CeO_2粒子周围非晶态的ZrO_2阻碍CeO_2的高温烧结,提高了该催化剂的稳定性。     

Roles of Oxygen Vacancies of CeO2 and Mn-Doped CeO2 with the Same Morphology in Benzene Catalytic Oxidation

Mn-doped CeO₂ and CeO₂ with the same morphology (nanofiber and nanocube) have been synthesized through hydrothermal method. When applied to benzene oxidation, the catalytic performance of Mn-doped CeO₂ is better than that of CeO₂, due to the difference of the concentration of O vacancy. Compared to CeO₂ with the same morphology, more oxygen vacancies were generated on the surface of Mn-doped CeO₂, due to the replacement of Ce ion with Mn ion. The lattice replacement has been analyzed through XRD, Raman, electron energy loss spectroscopy and electron paramagnetic resonance technology. The formation energies of oxygen vacancy on the different exposed crystal planes such as (110) and (100) for Mn-doped CeO₂ were calculated by the density functional theory (DFT). The results show that the oxygen vacancy is easier to be formed on the (110) plane. Other factors influencing catalytic behavior have also been investigated, indicating that the surface oxygen vacancy plays a crucial role in catalytic reaction.     

Metal–Organic Framework (MOF)-Derived Carbon-Mediated Interfacial Reaction for the Synthesis of CeO2−MnO2 Catalysts

CeO₂-based catalysts are widely studied in catalysis fields. Developing one novel synthetic approach to increase the intimate contact between CeO₂ and secondary species is of particular importance for enhancing catalytic activities. Herein, an interfacial reaction between metal–organic framework (MOF)-derived carbon and KMnO₄ to synthesize CeO₂−MnO₂, in which carbon is derived from the pyrolysis of Ce-MOFs under an inert atmosphere, is described. The MOF-derived carbon is found to restrain the growth of CeO₂ crystallites under a high calcination temperature and, more importantly, intimate contact within CeO₂/C is conveyed to CeO₂/MnO₂ after the interfacial reaction; this is responsible for the high catalytic activity of CeO₂−MnO₂ towards CO oxidation.     

Novel Ni/CeO2-Al2O3 composite catalysts synthesized by one-step citric acid complex and their performance in catalytic partial oxidation of methane

A series of novel Ni/CeO2-Al2O3composite catalysts were synthesized by one-step citric acid complex method. The as-synthesized catalysts were characterized by N2physical adsorption/desorption, X-ray diffraction(XRD), Fourier transform infrared(FT-IR) spectroscopy, hydrogen temperature-programmed reduction(H2-TPR), X-ray photoelectron spectroscopy(XPS) and thermogravimetry analysis(TGA). The effects of nickel content, calcination and reaction temperatures, gas hourly space velocity(GHSV) and inert gas dilution of N2on their performance of catalytic partial oxidation of methane(CPOM) were investigated. Catalytic activity test results show that the highest methane conversion(85%), the best selectivities to carbon monoxide(87%) and to hydrogen(95%), the excellent stability and perfect H2/CO ratio(2.0) can be obtained over Ni/CeO2-Al2O3with 8 wt% Ni content calcined at 700 ℃ under the reaction condition of 750 ℃, CH4/O2ratio of 2 : 1 and gas hourly space velocity of 12000 mL h-1 g-1. Characterization results show that the good catalytic performance of this composite catalyst can be contributed to its large specific surface area(～108 m2 g-1), small crystallite size, easy reducibility and low coking rate.     

Revealing the unexpected promotion effect of EuOx on Pt/CeO2 catalysts for catalytic combustion of toluene

Pt/Eu₂O₃-CeO₂ materials with different Eu concentrations were prepared and applied to toluene destruction, and the remarkable promotion impact of EuO_x on Pt/CeO₂ can be observed. The characterization results reveal that the presence of EuO_x significantly enhances the redox property, lattice O concentration, and Ce³⁺ ratio of the Pt/CeO₂ material, which facilitates the dispersion and activity of Pt active sites and thus accelerates the decomposition process of toluene. Among all catalysts, a sample with an Eu content of 2.5 at.% (Pt/EC-2.5) possesses the best catalytic activity with 0.09 vol% of toluene completely destructed at 200 °C under a relatively high GHSV of 50000 h^?1. The possible reaction pathway and mechanism of toluene combustion over Pt/Eu₂O₃-CeO₂ samples are presented according to in-situ DRIFTS, which confirms that the toluene oxidation process obeys the Mars-van Krevelen mechanism with aldehydes and ketones as primary organic intermediates.     

Oxidation of toluene on Bi-doped PbO<Subscript>2</Subscript> studied by electrochemical impedance spectroscopy and UV spectrophotometry

Oxidation of organics in the potential region of O₂ evolution is supposed to proceed through the oxidation of water to hydroxyl radicals, which then may either be further oxidized to give molecular oxygen or interact with organic molecules in an oxygen transfer reaction. Therefore, the electrode material must ensure (1) the preferential adsorption of the organic compound, (2) the production of adsorbed hydroxyl radicals able to react with this compound in a selective oxidation reaction (with as little as possible oxygen evolution), and (3) a long-term stability. In the present paper, the oxidative decomposition of toluene in sulfuric acid solution on PbO₂ coatings deposited on Ti substrate from acidic nitrate + fluoride baths containing Pb²⁺ and Bi³⁺ is investigated by voltammetry, electrochemical impedance spectroscopy, and UV spectrophotometry. The chemical composition and structure of the catalytic coatings is characterized with X-ray photoelectron spectroscopy and X-ray diffraction. The catalytic activity is estimated both from current density vs potential and polarization resistance vs potential plots using measurements on the same electrodes in sulfuric acid without toluene to eliminate the oxygen evolution reaction that proceeds in parallel to the oxidation of toluene. A skeletal reaction mechanism of the process is proposed to account for the steady-state and transient response of the catalytic electrodes during oxidation of toluene.     

非晶态ZrO2镶嵌的超细CeO2催化HCl氧化

采用不同方法制备了铈锆复合氧化物催化剂用于催化HCl氧化反应。自发沉积策略制备的CeO₂@ZrO₂催化剂中,超细CeO₂纳米粒子均匀的镶嵌于非晶态ZrO₂中。CeO₂粒子显著的“尺寸效应”使得该催化剂具有更高的Ce³⁺和氧空位浓度,而较高的Ce³⁺和氧空位浓度使得催化剂具有优异的低温氧化还原性能和储释氧能力。催化性能测试表明,CeO₂@ZrO₂催化剂展现出最好的催化活性（1.90 g_Cl2·g_cat^-1·h^-1）,同时CeO₂粒子周围非晶态的ZrO₂阻碍CeO₂的高温烧结,提高了该催化剂的稳定性。     

Controllable construction of Ce-Mn-Ox with tunable oxygen vacancies and active species for toluene catalytic combustion

A series of Ce-Mn-O_x catalysts synthesized under different hydrothermal conditions were evaluated by catalytic removal of toluene. The results of characterization showed that the contents of oxygen vacancies and active species in catalysts were crucial for the catalytic oxidation process. The concentration of Ce³⁺, Mn³⁺, and adsorbed oxygen associated with structural defects in Ce-Mn-O_x catalysts could be controlled by hydrothermal conditions, which were considered to promote redox capacity and improve catalytic oxidation performance. In addition, suitable synthetic conditions could increase the S_BET and V_p of catalysts. Among the prepared catalysts, CM-100 showed the best catalytic performance due to the generation of more defective oxygen and active species (Ce³⁺, Mn³⁺, and surface-adsorbed oxygen). In addition, the CM-100 catalyst showed satisfactory water resistance and stability.     

Co3O4−CeO2 Nanocomposites for Low-Temperature CO Oxidation

In an effort to combine the favorable catalytic properties of Co₃O₄ and CeO₂, nanocomposites with different phase distribution and Co₃O₄ loading were prepared and employed for CO oxidation. Synthesizing Co₃O₄-modified CeO₂ via three different sol-gel based routes, each with 10.4 wt % Co₃O₄ loading, yielded three different nanocomposite morphologies: CeO₂-supported Co₃O₄ layers, intermixed oxides, and homogeneously dispersed Co. The reactivity of the resulting surface oxygen species towards CO were examined by temperature programmed reduction (CO-TPR) and flow reactor kinetic tests. The first morphology exhibited the best performance due to its active Co₃O₄ surface layer, reducing the light-off temperature of CeO₂ by about 200 °C. In contrast, intermixed oxides and Co-doped CeO₂ suffered from lower dispersion and organic residues, respectively. The performance of Co₃O₄-CeO₂ nanocomposites was optimized by varying the Co₃O₄ loading, characterized by X-ray diffraction (XRD) and N₂ sorption (BET). The 16–65 wt % Co₃O₄−CeO₂ catalysts approached the conversion of 1 wt % Pt/CeO₂, rendering them interesting candidates for low-temperature CO oxidation.     

Insight into the Morphology-Dependent Catalytic Performance of CuO/CeO2 Produced by Tannic Acid for Efficient Hydrogenation of 4-Nitrophenol

The construction of a heterogeneous nanocatalyst with outstanding catalytic performance via an environmentally benign and cost-effective synthetic category has long been one of the challenges in nanotechnology. Herein, we synthesized highly efficient and low-cost mesoporous morphology-dependent CuO/CeO₂-Rods and CuO/CeO₂-Cubes catalysts by employing a green and multifunctional polyphenolic compound (tannic acid) as the stabilizer and chelating agent for 4-nitrophenol (4-NP) reduction reaction. The CuO/CeO₂-Rods exhibited excellent performance, of which the activity was 3.2 times higher than that of CuO/CeO₂-Cubes. This can be connected with the higher density of oxygen vacancy on CeO₂-Rods (110) than CeO₂-Cubes (100), the oxygen vacancy favors anchoring CuO species on the CeO₂ support, which promotes the strong interaction between finely dispersed CuO and CeO₂-Rods at the interfacial positions and facilitates the electron transfer from BH₄⁻ to 4-NP. The synergistic catalytic mechanism illustrated that 4-NP molecules preferentially adsorbed on the CeO₂, while H₂ from BH₄⁻ dissociated over CuO to form highly active H* species, contributing to achieving efficient hydrogenation of 4-NP. This study is expected to shed light on designing and synthesizing cost-effective and high-performance nanocatalysts through a greener synthetic method for the areas of catalysis, nanomaterial science and engineering, and chemical synthesis.     

Effect of preparation procedure on the properties of CeO2

The effect of preparation procedure on the physicochemical and catalytic properties of CeO₂ was studied. Differences in the electronic and structural characteristics of CeO₂ depending on preparation procedure and treatment temperature were found using X-ray diffraction analysis, transmission electron microscopy, UV-visible electronic spectroscopy, and X-ray photoelectron spectroscopy. With the use of the temperature-programmed reaction with CO, it was demonstrated that CeO₂ samples with a high concentration of point defects—oxygen vacancies caused by the presence of Ce³⁺—were characterized by an increased mobility of bulk oxygen. The samples of CeO₂ with a high concentration of structural defects—micropores of size 1–2 nm and stepwise vicinal faces in crystallites—exhibited a high catalytic activity in the reaction of CO oxidation.     

Triangle Cl−Ag1−Cl Sites for Superior Photocatalytic Molecular Oxygen Activation and NO Oxidation of BiOCl

BiOCl photocatalysis shows great promise for molecular oxygen activation and NO oxidation, but its selective transformation of NO to immobilized nitrate without toxic NO₂ emission is still a great challenge, because of uncontrollable reaction intermediates and pathways. In this study, we demonstrate that the introduction of triangle Cl−Ag₁−Cl sites on a Cl-terminated, (001) facet-exposed BiOCl can selectively promote one-electron activation of reactant molecular oxygen to intermediate superoxide radicals (⋅O₂⁻), and also shift the adsorption configuration of product NO₃⁻ from the weak monodentate binding mode to a strong bidentate mode to avoid unfavorable photolysis. By simultaneously tuning intermediates and products, the Cl−Ag₁−Cl-landen BiOCl achieved >90 % NO conversion to favorable NO₃⁻ of high selectivity (>97 %) in 10 min under visible light, with the undesired NO₂ concentration below 20 ppb. Both the activity and the selectivity of Cl−Ag₁−Cl sites surpass those of BiOCl surface sites (38 % NO conversion, 67 % NO₃⁻ selectivity) or control O−Ag₁−O sites on a benchmark photocatalyst P25 (67 % NO conversion and 87 % NO₃⁻ selectivity). This study develops new single-atom sites for the performance enhancement of semiconductor photocatalysts, and also provides a facile pathway to manipulate the reactive oxygen species production for efficient pollutant removal.     

乙二醇溶剂热合成的CeO2的可逆氧化还原性及CO2捕获性能

利用乙二醇的还原性,采用乙二醇溶剂热法制备了表面具有丰富氧空穴的CeO₂-GST纳米晶,对其进行了X射线衍射、透射电镜、X射线光电子能谱、原位H₂还原-O₂氧化循环和CO₂原位红外漫反射表征,并研究了其可逆氧化还原性及CO₂捕获性能. 结果表明,与CeO₂-nanorod和柠檬酸溶胶法合成的CeO₂-CA样品相比,CeO₂-GST纳米晶具有最好的可逆氧化还原性能和循环稳定性,同时在50 ℃下具有最好的CO₂吸附性能（149 μmol/g）. 利用原位红外漫反射光谱研究了CO₂在还原CeO₂表面的吸附情况,发现CO₂主要以双齿碳酸盐和桥连碳酸盐两种形式吸附在CeO₂表面,其中桥连碳酸盐物种不稳定,He吹扫可脱附. 此外,CO₂在CeO₂-nanorod上还会生成稳定的甲酸盐和单齿碳酸盐物种.     

Photo–thermo Catalytic Oxidation over a TiO2-WO3-Supported Platinum Catalyst

Photo–thermo catalysis, which integrates photocatalysis on semiconductors with thermocatalysis on supported nonplasmonic metals, has emerged as an attractive approach to improve catalytic performance. However, an understanding of the mechanisms in operation is missing from both the thermo- and photocatalytic perspectives. Deep insights into photo–thermo catalysis are achieved via the catalytic oxidation of propane (C₃H₈) over a Pt/TiO₂-WO₃ catalyst that severely suffers from oxygen poisoning at high O₂/C₃H₈ ratios. After introducing UV/Vis light, the reaction temperature required to achieve 70 % conversion of C₃H₈ lowers to a record-breaking 90 °C from 324 °C and the apparent activation energy drops from 130 kJ mol⁻¹ to 11 kJ mol⁻¹. Furthermore, the reaction order of O₂ is −1.4 in dark but reverses to 0.1 under light, thereby suppressing oxygen poisoning of the Pt catalyst. An underlying mechanism is proposed based on direct evidence of the in-situ-captured reaction intermediates.