会聚激光扫描铌酸锂晶体写入光波导时的最佳曝光间距

对利用激光精细加工技术在铌酸锂(LiNbO₃)晶体中写入光波导时的最佳曝光间距进行了详细地理论分析和实验研究.通过数值求解简化后的光折变动力学方程组，对会聚激光束沿不同方向扫描晶体时的最佳曝光间距进行了详细的数值模拟.结果表明：最佳曝光间距的选取与写入光束的扫描方向无关；当聚焦激光束平行于光轴扫描晶体时，得不到波导结构，但可以采用“三明治”辐照方式得到对称的折射率分布.采用会聚的绿激光束扫描掺铁铌酸锂(LiNbO₃：Fe)晶体进行了实验研究，晶体中的光致折射率变 关键词： 激光精细加工 最佳曝光间距 光波导 3晶体')" href="#">LiNbO₃晶体     

全息明孤子的波导特性

研究了光折变晶体中的全息明孤子所产生的波导的特性，结果表明波导所有可能的导模数依赖于产生波导的全息明孤子光的强度.利用数值计算给出了在不同的孤子强度时波导的导模并考察了波导对导模和正弦余弦波的动态导引.     

Optical Learning Neural Network Using Photorefractive Waveguides

A model of an optical neural network with learning ability is proposed. We numerically evaluate the learning ability of the proposed network by using parameters determined by experiments. Adaptive connections between artificial neurons are implemented using photorefractive (PR) waveguides that can be optically modified by guided beams. The network consists of three layers and has bipolar weights within the limited range. The bipolar weight is encoded as the difference between optical power transmittances of signal beams in two channels of the PR waveguides. The adaptivity of the transmittance of PR waveguide is experimentally evaluated and is incorporated into the proposed network simulated in a computer. The proposed network is trained by a simplified local learning algorithm. Numerical results showed that the proposed three-layered network with six hidden neurons can solve the exclusive-or problem.     

光束传播法分析硅交叉波导光开关的光学效应

运用光束传播法对硅交叉波导全内反射光开关中的光学效应进行了详细分析。结果表明：１）光学表面衰减波和泄漏波所引发的光遂道效应对开关特性有重要影响；２）反射端功率的相对大小于与反射区界面位置密切相关，其起因是古斯－汉欣位移；３）合理考虑这些因素的影响可以大大降低器件对折射率变化的要求。     

亮孤子在宇称时间对称波导中的传输和控制

基于光波在宇称-时间(PT)对称波导中传输的理论模型, 数值研究了亮孤子在呈高斯分布的PT对称克尔非线性平板波导中的传输和控制. PT对称波导, 要求波导的折射率分布呈偶对称, 而增益/损耗分布呈奇对称. 结果表明: 当波导的折射率分布强度为正时, PT对称波导的中心折射率最大, 即使没有自聚焦克尔非线性效应, PT对称波导也可以束缚光波, 形成波浪形光束且长距离传输; 当折射率分布强度为负时, PT对称波导的中心折射率最小, 光波的传输方向发生偏移. 而增益/损耗分布可控制光波的偏移方向: 增益/损耗分布强度为正, 光波向左偏移; 强度为负, 光波向右偏移; 强度为零时, 光波被分为两束. 且当折射率分布强度为负时, 可以很好地抑制相邻亮孤子间的相互作用. 该研究结果可为未来PT对称波导在全光控制方面的应用提供一定的理论依据.     

Waveguide properties and optical switching of prism-coupled Au:SiO2 nanocomposite films

In this study, we present theoretical and experimental analyses on the waveguide mode properties of prism-coupled Au:SiO₂ nanocomposite films with the near infrared laser of 1550 nm wavelength where the optical absorption diminished enough for the generation of guided mode. The evolution of guided mode in the nanocomposite waveguide and its propagation properties were also evaluated. As an effective way of utilizing the surface plasmon resonance properties for the application to optical switching devices, we employed an attenuated total internal reflection type optical switch geometry and tested its effectiveness for the absorptive opto-functional materials system using a cross-modulation technique with 532-nm pump and 1550-nm probe beams. The index change probe beam experiences was found to be purely refractive in nature and negative in sign, presumably due to the photo-thermal effect induced in the nanocomposite film by the irradiation of pump beam.     

SOI波导反射模式的古斯-汉欣空间位移效应及其数字式热光开关

借助波导转角镜结构,利用古斯-汉欣空间位移和热光效应折射率调制的有效组合,提出了波导反射模式数字式热光开关结构.在给定入射角的条件下优化了空间古斯-汉欣位移,在具有古斯-汉欣效应的本征态下,反射光束出现了较大的跳跃.在1.0μm厚硅膜的绝缘体上硅平台上,单模输入波导和多模干涉波导结构之间的导模本征态匹配,验证了1×3数...     

All-optical wavelength tuning in Ti:PPLN Šolc filter via the photorefractive effect

We demonstrate fine-wavelength tuning of a periodically poled Ti:LiNbO₃ (Ti:PPLN) Šolc filter by use of the photorefractive (PR) effect. The center wavelength of a Ti:PPLN Šolc filter is controlled by the PR effect, which is induced by second-harmonic generation (SHG). The refractive index change caused by the PR effect is calculated from the measured shift in center wavelength from the Ti:PPLN Šolc filter. The experimental results show that all-optical fine-wavelength tuning in a Ti:PPLN Šolc filter is possible by the use of a second-order nonlinear effect and that a Ti:PPLN waveguide has much higher resistance to PR damage than a Ti:LiNbO₃ waveguide. The measured wavelength tuning rate as a function of the pump beam power is about − 0.033 nm/mW.     

Beam Steering Type of 1 : 4 Optical Switch Using Thermo-Optic Effect

We propose a beam steering type optical switch employing a phase shifter. It consists of collimating waveguide mirrors, an arrayed-waveguide which has deep trenches incorporating polymer materials, and input/output waveguides. The incident light is guided to the front mirror, where it is then collimated, and input to the arrayed waveguide. The number of trenches filled with polymer linearly increases in order. The refractive index of the polymer can be controlled with temperature, and the propagation direction of the output light from the arrayed waveguide can also be controlled. A switch with 15 waveguides in the array has been fabricated. The chip size is about 2:5 × 9:0 mm², the insertion loss is 10 dB, and the extinction ratio is about 10–13 dB.     

非线性导波现象

本文评述发生在波导结构内的三次非线性光学现象及其潜在的应用。由于波导媒质具有光强感应折射率特性,从而引起导波矢量和场分布与耦合进波导内的光功率密度有关。基于这一概念,导致了很多有趣的全光器件,诸如:光限制器,光开关,光双稳,光扫描,光控调谐滤波,光控波导互连转换等。     

An azobenzene functionalized polymer for laser direct writing waveguide fabrication

We report on non-lithographic laser direct writing fabrication of optical waveguides by using a 4′-hydroxy-4-nitroazobene dye-functionalized polymer film. The polymer film reveals permanent change of refractive index at high laser illumination intensity. A focused continuous wave low power green laser beam at 532 nm wavelength is used to directly write waveguide structures on the polymer film. The magnitude of refractive index increase at film surface is about 0.006. One-step laser writing results in graded index waveguides in film depth direction under ambient conditions without pre- and post-processing. As a by-product, the laser writing also results in a very small air valley at the boundary between the laser written and non-written regions which may contribute in part although minimal to the waveguide lateral confinement and can be used for visual observation of waveguide patterns. The fabricated waveguide is found to be stable and easily reproducible.     

非线性一维光子晶体波导光双稳

利用非线性折射率系数较大且非线性时间响应较快的CdS_xSe_1-x玻璃为材料,设计并制备了非线性一维光子晶体波导光双稳器件,该器件的折射率空间分布呈正弦形式。实验测得双稳开关的阈值功率密度为1.60×10⁵W/cm²,开关时间为63ps。采用时域有限差分方法讨论了光子晶体带隙随入射光强变化而移动的情况,随着入射光功率密度的增加,光子晶体的带隙中心向短波方向移动。同时计算了该器件的双稳特性,理论计算得到双稳开关的阈值功率密度为1.40×10⁵W/cm²,开关时间约为50ps。获得了理论与实验基本一致的结果。     

一维光学格子孤子的传输特性及控制研究

利用解析和数值方法研究了在具有横向折射率周期性调制的克尔型非线性介质中光学格子孤子的传输，得到了孤子参数的演化方程以及格子孤子的形成和稳定传输的条件.结果表明：当光束的入射角小于某临界角度时，光束可被类似波导形式的路径俘获而稳定传输，该临界角随折射率调制周期、调制深度的增加而增大，且光束越窄临界值越大.此外，线性空间啁啾虽然对光束传输的中心位置没有任何影响，但会导致光束发散从而破坏格子孤子的形成和稳定传输，对此提出了采用特定功率取值来补偿啁啾作用从而形成格子孤子的方案. 关键词： 光孤子 光学格子 光传输 矩方法     

Asymmetrical off–on switches for crosstalk reduction in switching networks

An off–on switching scheme is introduced which blocks a waveguide path in the passive off-state and transmits the signal in the active on-state. The operating principle is based on the self-diffraction of a narrow guided beam when it escapes from a waveguide with two-dimensional confinement into a region of appropriate length with basically one-dimensional confinement. In particular, a remaining interface of the initial waveguide superimposes reflection, which in sum results in a very efficient asymmetrical blow out of the guided power. In the active on-state, low-loss waveguiding is sustained when an electrode causes an appropriate refractive index change, e.g., due to the thermo-optical effect. Thus, the signal is received in the output waveguide, the identical counterpart of the input guide. The switching behaviour is almost binary with minimal wavelength dependence. This makes the device useful for switching and modulation in a multi-wavelength optical network. For a realistic polymeric waveguide configuration, simulations indicate on-off signal ratios of >30 dB. This satisfies the requirements for crosstalk reduction in switching networks.     

光折变表面波诱导的薄层波导中的导波模式

利用数值模拟对扩散非线性机制下由光折变表面波诱导的薄层波导中导模的形成和特点进行了研究。采用分布傅里叶法对导模的传输特性进行了模拟。通过求解本征方程,对光折变表面波诱导的薄层波导中存在的导波模式进行了数值求解。通过调节传播常数和波导参数的方法,可以控制导模的阶数和传播波形。随着阶数的增加,导模轮廓的对称性越来越差;随着波导参数的增加,导模的峰值振幅单调递增。导模的能量主要聚集在晶体薄层波导中靠近-c轴的一侧,随着传播常数的增大,导模能量先减小后增大,且导模可以稳定传播。     

梳状波导结构中石墨烯表面等离子体的传播性质

理论上研究了介质/石墨烯/介质梳状波导结构中表面等离子体的传播性质. 波导中表面等离子体模的有效折射率随着石墨烯费米能级的提高而减小, 随着介质折射率的增加而增加. 分析和仿真结果表明, 基于这种梳状波导可以在中红外波段实现新型的纳米等离子体滤波器, 器件的尺度在几百纳米的范围. 通过改变梳状分支的长度, 石墨烯的费米能级, 介质的折射率和波导中石墨烯的层数, 很容易来调节带隙的位置. 另外, 滤波带隙的宽度随着梳状分支数的增加而增加. 这种滤波性质将在可调的高集成光子滤波器件中具有潜在的应用.     

Experimental observation and numerical simulation of guided modes in Nd:YLiF4 channel waveguides produced by carbon ion implantation

We report on, to our knowledge the first time, the channel waveguide formation in Nd:YLiF₄ laser crystal produced by 6 MeV carbon ion implantation. The guided modes are observed by using an end‐face arrangement. We construct the two‐dimensional (2D) refractive index profile of the channel waveguide cross section, which is based on the related planar waveguide index distribution as well as the rectangular shape of the waveguide cross sections. The modal intensity distribution is numerically calculated by using the beam propagation method according to the reconstructed index profile, which shows a reasonable agreement with the experimental result. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Critical ray-like propagation modes along graded-index planar optical waveguides

Graded-index planar optical waveguides and surface compression layers were formed simultaneously in the surface layer of glass plates by ion exchange. A change in the refractometer patterns was observed. Before ion exchange, only a critical ray fringe was observed, but with ion exchange a guided wave fringe appeared on the high effective refractive index side of the ‘critical ray’ fringe, and the number of guided wave fringes increased. The guided wave fringe or fringes were birefringent, whereas the ‘critical ray’ fringe was kept nonbirefringent. It was concluded that the ‘critical ray’ propagated along the bottom of a waveguide, ie at the foot of the refractive index distribution.     

低功率近红外光的偏振方向对光致折射率变化影响的实验研究

研究了利用低功率近红外光辐照In:Fe:LiNbO3晶体时写入光束的偏振方向对光致折射率变化(Δn)的影响.分别采用正常偏振(o光)和非常偏振(e光)的近红外细激光束,在In:Fe:LiNbO3晶体中进行了光折变实验.研究表明,两种偏振方向引起晶体的Δn实测曲线相似,但变化规律恰好相反,o光引起的折射率变化量约是e光的3倍左右.近红外光写入下两种偏振光束引起晶体的Δn分布规律都不同于可见光,尤其是e光辐照区域中心晶体的折射率升高.因此,通过选择不同偏振方向的近红外光可以在光折变晶体中制作不同折射率分布的非线性光学器件.     

Design strategies to increase the brightness of gain guided tapered lasers

The basic operating principles of gain guided tapered lasers are studied in detail by means of numerical simulations. The carrier induced lensing effect caused by spatial hole burning is described as the main mechanism limiting the device performance. The influence of the following design parameters in the maximum output power and beam brightness is analyzed: refractive index step of the ridge waveguide section, angle and length of the tapered section, and the use of beam spoilers. The results provide design guidelines for improving the device performance.