Amorphous Ni-Co-S nanocages assembled with nanosheet arrays as cathode for high-performance zinc ion battery

The selection and development of cathode of alkaline zinc batteries （AZBs） is still hindered and often leads to poor rate capability and short cycle life. Here, amorphous hollow nickel-cobalt-based sulfides nanocages with nanosheet arrays （AM-NCS） are designed and constructed with ZIF-67 as the selftemplate to exchange with Ni²⁺and S^2-by using a two-step ion exchange method. The synthesized AM-NCS possess the high specific capacity （160 m Ah/g at 2 A/g）, and the assembled b...     

方铁锰矿Mn2O3作为正极材料的高比容量可充电水性锌离子电池

由于具有低成本、高安全性、组装简易方便等优点,水性可充电锌离子二次电池被认为是太阳能和风能的最佳储能装置,尤其是锌锰二次电池.目前,锰正极材料的研究较多集中在二氧化锰上,同时,也有关于Mn2O3的研究,但比容量及能量密度皆较低.本文合成了方铁锰矿Mn2O3并将其用于水性锌离子电池的正极材料,在0.2C倍率下充放时,获得...     

Improved disordered carbon as high performance anode material for lithium ion battery

A sulfur-substituted disordered carbon is explored as anode material for lithium-ion battery. Its physical and electrochemical properties are characterized by a variety of techniques such as powder X-ray diffraction, element analysis, Fourier transform infrared spectrum, scanning electron microscopy, and typical electrochemical tests. Electrochemical tests show the activated carbon displays a first cycle discharge capacity of 1,216 mAh·g⁻¹. It also has a remarkable cycling stability with an average capacity fade of 0.92% per cycle from 11th to 100th cycle in the range of 0.01–3.00 V versus metallic lithium at a current density of 100 mA·g⁻¹. After 100 cycles, the electrode still maintained a capacity of 420 mAh·g⁻¹.     

Structural modulation in the high capacity battery cathode material LiFeBO3

The crystal structure of the promising Li-ion battery cathode material LiFeBO(3) has been redetermined based on the results of single crystal X-ray diffraction data. A commensurate modulation that doubles the periodicity of the lattice in the a-axis direction is observed. When the structure of LiFeBO(3) is refined in the 4-dimensional superspace group C2/c(α0γ)00, with α = 1/2 and γ = 0 and with lattice parameters of a = 5.1681 ?, b = 8.8687 ?, c = 10.1656 ?, and β = 91.514°, all of the disorder present in the prior C2/c structural model is eliminated and a long-range ordering of 1D chains of corner-shared LiO(4) is revealed to occur as a result of cooperative displacements of Li and O atoms in the c-axis direction. Solid-state hybrid density functional theory calculations find that the modulation stabilizes the LiFeBO(3) structure by 1.2 kJ/mol (12 meV/f.u.), and that the modulation disappears after delithiation to form a structurally related FeBO(3) phase. The band gaps of LiFeBO(3) and FeBO(3) are calculated to be 3.5 and 3.3 eV, respectively. Bond valence sum maps have been used to identify and characterize the important Li conduction pathways, and suggest that the activation energies for Li diffusion will be higher in the modulated structure of LiFeBO(3) than in its unmodulated analogue.     

Copper fluoride as a low-cost sodium-ion battery cathode with high capacity

Sodium-ion batteries（SIBs） are promising alternatives to lithium-ion batteries（LIBs） for large-scale energy storage considering the abundance and low cost of Na-containing resources. However, the energy density of SIBs has been limited by the typically low specific capacities of traditional intercalation-based cathodes. Metal fluorides, in contrast, can deliver much higher capacities based on multi-electron conversion reactions. Among metal fluorides, CuF₂ presents a theoretical speci...     

A novel carbon-coated LiCoO2 as cathode material for lithium ion battery

Using a commercially available LiCoO₂ as starting material, a surface-modified cathode material was obtained by coating it with a nano layer of amorphous carbon. The carbon-coated LiCoO₂ was characterized by X-ray diffraction analysis, scanning electronic microscopy, transmission electronic microscopy, electrochemical impedance spectroscopy and measurement of charge/discharge behavior. Results show that the carbon-coated LiCoO₂ displays marked lower charge transfer resistance, higher lithium ion diffusion coefficient and much better rate capability than the original LiCoO₂. It also indicates promising application of lithium ion batteries in the areas requiring charge and discharge at high rate.     

Tremella-like molybdenum dioxide consisting of nanosheets as an anode material for lithium ion battery

Tremella-like structured MoO₂ consisting of nanosheets was obtained via a Fe₂O₃-assisted hydrothermal reduction of MoO₃ in ethylenediamine aqueous solution. The as-prepared product was characterized and tested with scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV) and capacity measurement as anode material for lithium ion batteries. This structured MoO₂ shows very high reversible capacity (>600 mA h g⁻¹), good rate capability and cycling performance, presenting potential application as anode material for lithium ion batteries with high rate capability and high capacity.     

Mesoporous carbon material as cathode for high performance lithium-ion capacitor

The mesoporous carbon material with large pore volume and high surface area by a simple situ MgO template method is synthesized, which is utilized as cathode to assemble a high performance lithium ion capacitor.     

Organic 3D interconnected graphene aerogel as cathode materials for high-performance aqueous zinc ion battery

Aqueous rechargeable zinc ion batteries are very attractive in large-scale storage applications,because they have high safety,low cost and good durability.Nonetheless,their advancements are hindered by a dearth of positive host materials(cathode)due to sluggish diffusion of Zn2+in the solid inorganic frameworks.Here,we report a novel organic electrode material of poly 3,4,9,10-perylentetracarboxylic dianhydride(PPTCDA)/graphene aerogel(GA).The 3D interconnected porous architecture synthesized through a simple solvothermal reaction,where the PPTCDA is homogenously embedded in the GA nanosheets.The self-assembly of PPTCDA/GA coin-type cell will not only significantly improve the durability and extend lifetime of the devices,but also reduce the electronic waste and economic cost.The self-assembled structure does not require the auxiliary electrode and conductive agent to prepare the electrode material,which is a simple method for preparing the coin-type cell and a foundation for the next large-scale production.The PPTCDA/GA delivers a high capacity of≥200 m Ah g^–1 with the voltage of 0.0~1.5 V.After 300 cycles,the capacity retention rate still close to 100%.The discussion on the mechanism of Zn2+intercalation/deintercalation in the PPTCDA/GA electrode is explored by Fourier transform infrared spectrometer(FT-IR),X-ray diffraction(XRD)and X-ray photoelectron spectroscopy(XPS)characterizations.The morphology and structure of PPTCDA/GA are examined by scanning electron microscopy(SEM)and transmission electron microscopy(TEM).     

N-doped coaxial CNTs@a-Fe_2O_3@C nanofibers as anode material for high performance lithium ion battery

N-doped coaxial CNTs@α-Fe_2O_3@C nanofibers have been successfully synthesized according to a facile solvothermal/hydrothermal method.The obtained CNTs@α-Fe_2O_3@C nanofibers composites exhibited special three-dimensional(3-D)network structure,which endows they promising candidate for anode materials of lithium ion battery.The coaxial property of CNTs@α-Fe_2O_3@C nanofibers could significantly improve the cycling and rate performance owing to the acceleration of charge/electron transfer,improvement of conductivity,maintaining of structural integrity and inhibiting the aggregation.Theα-Fe_2O_3nanoparticles with small size and high percentage of N-doped amount could further improve the electrochemical performance.As for the CNT@α-Fe_2O_3@C nanofibers,the capacity presented a high value of1255.4 mAh/g at 0.1 C,and retained at 1213.4 mAh/g after 60 cycles.Even at high rate of 5 C,the capacity still exhibited as high as 319 mAh/g.The results indicated that the synthesized N-doped coaxial CNTs@α-Fe_2O_3@C nanofibers exhibited high cycling and rate performance.     

锂离子电池正极材料LiFePO4的密度泛函研究

采用密度泛函(B3LYP)方法计算锂离子电池正极材料LiFePO4/FePO4,净电荷和共价键级的计算结果都表明磷氧原子间作用力最强,锂氧原子间作用力最弱,有利于Li离子在晶格中的自由移动.以Li/LiFePO4锂离子电池的平均电压为3.2 V,和实验值3.4 V基本一致.态密度分析表明FePO4和LiFePO4都是典型的半导体,O原子轨道主要贡献总态密度靠费米能级价带一侧,Fe原子轨道主要贡献总态密度靠费米能级导带一侧.     

Nanostructured nickel sulfide synthesized via a polyol route as a cathode material for the rechargeable lithium battery

Nanostructured nickel sulfide (NiS) was synthesized via a simple polyol route. The NiS powders were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and electrochemical testing. The results revealed that the cycle life of the annealed NiS sample was improved over that of the as-prepared sample. The electrochemical performance was also tested using 1 M lithium trifluoromethanesulfonimide (LiTFSI) in a solvent of poly(ethylene glycol) dimethyl ether (PEGDME) in order to compare with a sample tested in the conventional electrolyte of 1 M LiPF₆ in a mixture of ethylene carbonate (EC) and dimethyl carbonate (DMC). The results showed that the electrochemical properties were improved by using the 1 M LiTFSI/PEGDME electrolyte.     

Hydrated ammonium manganese phosphates by electrochemically induced manganese-defect as cathode material for aqueous zinc ion batteries

Aqueous zinc ion batteries (AZIBs) with the merits of low cost, low toxicity, high safety, environmental benignity as well as multi-valence properties as the large-scale energy storage devices demonstrate tremendous application prospect. However, the explorations for the most competitive manganese-based cathode materials of AZIBs have been mainly limited to some known manganese oxides. Herein, we report a new type of cathode material NH₄MnPO₄·H₂O (abbreviated as AMPH) for rechargeable AZIBs synthesized through a simple hydrothermal method. An in-situ electrochemical strategy inducing Mn-defect has been used to unlock the electrochemical activity of AMPH through the initial charge process, which can convert poor electrochemical characteristic of AMPH towards Zn²⁺ and NH₄⁺ into great electrochemically active cathode for AZIBs. It still delivers a reversible discharge capacity up to 90.0 mAh/g at 0.5 A/g even after 1000^th cycles, which indicates a considerable capacity and an impressive cycle stability. Furthermore, this cathode reveals an (de)insertion mechanism of Zn²⁺ and NH₄⁺ without structural collapse during the charge/discharge process. The work not only supplements a new member for the family of manganese-based compound for AZIBs, but also provides a potential direction for developing novel cathode material for AZIBs by introducing defect chemistry.     

熔融浸渍法制备锂离子电池正极材料LiMn2O4的研究

采用LiNO3和MnO2为原料,在650℃下制备了尖晶石型的LiMn2O4.通过X射线衍射、扫描电子显微镜、热重分析和电化学性能测试,发现该化合物具有很高的放电比容量和较好的循环性能,首次放电比容量可达到122 mA·h/g.并对循环性能衰减的各种因素进行了讨论.     

Synthesis and high rate properties of nanoparticled lithium cobalt oxides as the cathode material for lithium-ion battery

Nanoparticled lithium cobalt oxides were synthesized by coprecipitation in ethanol. Mechanical stirring was used to control the particle growth. The controlled grain size was below 100 nm with a narrow distribution. The structure has been examined using X-ray diffraction. On hand of an experimental cell it appears that the novel material has an exciting high charge and discharge rate: the capacity is 100 mA h/g for a 50C rate and 130 mA h/g for a 10C rate.     

Cauliflower-like nanostructured ZnV2S4 as a potential cathode material to boost-up high capacity and durability of the aqueous zinc-ion battery

Owing to their unique design and development, high safety and low-cost efficient cathode is still at the forefront of research for rechargeable zinc-ion batteries. However, the suitable cathode operating with ultrahigh capacity with a dendrite-free anode reaction mechanism remains challenging. In this, the first archetype of a high-rate and morphologically stabled cathode material is constructed from novel cauliflower-like nano-ZnV₂S₄ for aqueous zinc-ion batteries. Thus, nano-ZnV₂S₄ was prepared with an anion exchange reaction using ZnV₂(OH)₈ cauliflower-like nanostructured array as a template interestingly no morphological and shape changes were detected. The as-prepared nano-ZnV₂S₄ electrode reveals a specific discharge capacity of 348.2 mAh/g during 0.5 A/g with enhanced rate capability and excellent capacity retention of 89.2% at 4 A/g current density even after completing 1000 cycles.     

Boron and nitrogen dual-doped carbon as a novel cathode for high performance hybrid ion capacitors

A high performance hybrid ion capacitors has been developed by using B, N dual-doped 3D superstructure carbon cathode and prelithiated graphite anode.     

Hierarchical hollow microcuboid LiNi0.5Mn1.5O4 as cathode material with excellent rate and cycling performance for lithium-ion batteries

Journal of Solid State Electrochemistry - The rational design of the structure is the key to engineering spinel LiNi0.5Mn1.5O4 cathode material to enhance Li+/electron transport and relieve the...