On-line preconcentration with activated carbon for microwave plasma torch atomic emission spectrometry

This paper presents a method whereby trace elements are adsorbed in NH(4)ClNH(3) medium on activated carbon and then determined by microwave plasma torch atomic emission spectrometry (MPT-AES). The working conditions (including microwave forward power, gas flow rate, NH(3)NH(4)Cl concentration in the sample solution, HCl concentration in the eluant, sample introduction rate and preconcentration time) were investigated in detail. The effects of concomitant ions were studied. The experimental results for such analytes as Pb, Mn, Cd, Cu and Fe indicate that the procedure can eliminate fundamentally the interferences caused by alkali and alkaline earth metal elements and the application of it to the determination of iron in industrial silicon and tap water samples is successful.     

Flow-injection potentiometris stripping analysis — a new concept for east trace determinations

Flow-injection potentiometric stripping analysis is introduced as a highly versatile technique for micro and trace determinations of heavy metals. The simple instrumentation used, with extremely short residence times (below 1 s), permits a simple throughput of 200 h^–1. Up to four elements can be determined simultaneously at lower μgl^? levels up to % levels. On-line sample manipulation (e.g., dilution and matrix modification is possible with one- and two-channel flow systems. The utility of f.i.p.s.a. is evaluted by comparing response, sensitivity, and practical aspects of four different flow-through cells. The method is successfully applied to the fast sequential measurements of zinc, lead and copper in tap water and to the direct determination of lad and cadmium in acid digests of biological samples without further treatment.     

Use of chelating resins and inductively coupled plasma mass spectrometry for simultaneous determination of trace and major elements in small volumes of saline water samples

For some saline environments (e.g. deeply percolating groundwater, interstitial water in marine sediments, water sample collected after several steps of fractionation) the volume of water sample available is limited. A technique is presented which enables simultaneous determination of major and trace elements after preconcentration of only 60 mL sample on chelating resins. Chelex-100 and Chelamine were used for the preconcentration of trace elements (Cd, Cu, Pb, Zn, Sc) and rare earth elements (La, Ce, Nd, Yb) from saline water before their measurement by inductively coupled plasma mass spectrometry. Retention of the major elements (Na, Ca, Mg) by the Chelamine resin was lower than by Chelex; this enabled their direct measurement in the solution after passage through the resin column. For trace metal recoveries both resins yield the same mass balance. Only Chelex resin enabled the quantitative recovery of rare earth elements. The major elements, trace metals and rare earth elements cannot be measured after passage through one resin only. The protocol proposes the initial use of Chelamine for measurement of trace and major elements and then passage the same sample through the Chelex resin for determination of the rare earth elements. The detection limit ranged from 1 to 12 pg mL^–1. At concentrations of 1 ng mL^–1 of trace metals and REE spiked in coastal water the precision for 10 replicates was in the range of 0.3–3.4% (RSD). The accuracy of the method was demonstrated by analyzing two standard reference waters, SLRS-3 and CASS-3.     

Adsorption of some toxic elements from water samples on modified activated carbon,activated carbon and red soil using neutron activation analysis

A simple and sensitive method for the determination of some metalloids and heavy metals in water samples is presented. The method is based on the preconcentration of the attachment of chelating functionalities with metalloids and toxic metals irreversibly and targeted towards toxic metals adsorbed on modified activated carbon, activated carbon and red soil particles at pH 3.0–9.0±0.2, followed by quantitative determination using instrumental neutron activation analysis (INAA), on the absorbers. Attachment results from attraction that may be physical, chemical, electrical, or a combination of all three. The efficient removal of metalloids and toxic metals, especially arsenic, chromium and mercury is anticipated. The adsorption capacity of the chemically modified activated carbon materials was evaluated for the above mentioned metalloid and toxic metal ions in the presence of iron ions and simulated water samples. Red soil particles containing iron was utilized in the control of oxidation-reduction reaction with metalloids and toxic metals. The preconcentration of the elements of interest on red soil particles, activated carbon and modified activated carbon at different depths, pH and oxidation states was investigated. The results obtained showed good agreement with certified values giving relative errors of less than 10%.     

Bamboo Charcoal as Solid-Phase Extraction Adsorbent for the Determination of Organophosphorus Pesticides in Water Samples by High-Performance Liquid Chromatography

In this paper, bamboo charcoal was successfully developed for the solid-phase extraction adsorbent for the determination of six organophosphorus pesticides in water samples. After the bamboo charcoal was pretreated and packed in the solid-phase extraction cartridge, the organophosphorus pesticides in water samples were carried out the solid-phase extraction. To establish a perfect solid-phase extraction procedure, the experimental conditions including the eluent, eluent volume, pH of the sample, flow rate of the sample, and loading volume of the sample were all investigated. When 100 mL water samples in the pH range of 6–7 were loaded with the flow rate of 2.5 mL · min^?1 and then eluted with 10 mL acetonitrile, the proposed extraction method was validated by the recovery, correlation coefficient (R²), repeatability (RSD, n = 7) and LODs, which were 69.6–93.4%, 0.9982–0.9998, 2.9–5.6%, and 0.08–1.04 µg · L^?1, respectively. Furthermore, the analysis of the tap, snow, and river water samples demonstrated the feasibility of the proposed SPE method for real water samples. Based on the aforementioned factors, it could be concluded that bamboo charcoal was a good solid-phase extraction adsorbent, and this proposed solid-phase extraction method was suitable for the effective enrichment and determination of the organophosphorus pesticides in water samples.     

Determination of trace rare earth elements by inductively coupled plasma atomic emission spectrometry after preconcentration with multiwalled carbon nanotubes

A new method has been developed for the determination of trace rare earth elements (REEs) in water samples based on preconcentration with a microcolumn packed with multiwalled carbon nanotubes (MWNTs) prior to their determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). The optimum experimental parameters for preconcentration of REEs, such as pH of the sample, sample flow rate and volume, elution solution and interfering ions, have been investigated. The studied REEs ions can be quantitatively retained by MWNTs when the pH exceed 3.0, and then eluted completely with 1.0 mol L⁻¹ HNO₃. The detection limits of this method for REEs was between 3 and 57 ng L⁻¹, and the relative standard deviations (RSDs) for the determination of REEs at 10 ng mL⁻¹ level were found to be less than 6% when processing 100 mL sample solution. The method was validated using a certified reference material, and has been successfully applied for the determination of trace rare earth elements in lake water and synthetic seawater with satisfactory results.     

Determination of As, Sb, Bi and Hg in water samples by flow-injection inductively coupled plasma mass spectrometry with an in-situ nebulizer/hydride generator

A simple and very inexpensive in-situ nebulizer/hydride generator was used with inductively coupled plasma mass spectrometry (ICP-MS) for the determination of As, Sb, Bi and Hg in water samples. The application of hydride generation ICP-MS alleviated the sensitivity problem of As, Sb, Bi and Hg determinations encountered when the conventional pneumatic nebulizer was used for sample introduction. The sample was introduced by flow injection to minimize the deposition of solids on the sampling orifice. The elements in the sample were reduced to the lower oxidation states with L-cysteine before being injected into the hydride generation system. This method has a detection limit of 0.003, 0.003, 0.017 and 0.17 ng ml⁻¹ for As, Bi, Sb and Hg, respectively. This method was applied to determine As, Sb, Bi and Hg in a CASS-3 nearshore seawater reference sample, a SLRS-2 riverine water reference sample and a tap water collected from National Sun Yat-Sen University. The concentrations of the elements were determined by standard addition method. The precision was better than 20% for most of the determinations.     

Application of high-surface-area ZrO2 in preconcentration and determination of 18 elements by on-line flow injection with inductively coupled plasma atomic emission spectrometry

A flow-injection analysis (FIA) system incorporating a micro-column of ZrO₂ has been used for the development of an on-line multi-element method for the simultaneous preconcentration and determination of Al, Bi, Cd, Co, Cr, Cu, Fe, Ga, In, Mn, Mo, Ni, Pb, Tl, V, Sb, Sn, and Zn by inductively coupled plasma atomic emission spectrometry (ICP–AES). The conditions for quantitative and reproducible preconcentration, elution, and subsequent on-line ICP–AES determination were established. A sample (pH 8) is pumped through the column at 3 mL min^–1 and sequentially eluted directly into the ICP–AES with 3 mol L^–1 HNO₃. With a sample volume of 100 mL and an elution volume of 1 mL signal enhancement 100 times better than for conventional continuous aspirating systems was obtained for the elements studied. The reproducibility (RSD %) of the method at the 10 ng mL^–1 level in the eluate is acceptable – less than 8% for five replicates. Recoveries between 95.4% and 99.9% were obtained for the elements analysed. ZrO₂, with a specific surface area of 57 m² g^–1 and a capacity of approximately 5 mg g^–1 for the elements studied, was synthesized by hydrolysis of ZrCl₄. The preconcentration system was evaluated for several simple synthetic matrices, standard water samples and synthetic seawater. The effect of foreign ions on the efficiency of preconcentration of the elements studied was investigated. The application of a micro-column filled with high-surface-area ZrO₂ and flow injection inductively coupled plasma atomic emission spectrometry enables preconcentration and simultaneous determination of 18 elements at low concentrations (ng L^–1) in different water samples.     

Determination of atrazine and simazine in environmental water samples using multiwalled carbon nanotubes as the adsorbents for preconcentration prior to high performance liquid chromatography with diode array detector

Multiwalled carbon nanotubes, a new nanoscale material, has been gained many interests for use in various fields, and has exhibited exceptional merit as SPE absorbents for enrichment of environmental pollutants. This paper focused on the enriching power of atrazine and simazine, two important widely used triazine herbicides and described a novel and sensitive method for determination of these two herbicides based on SPE using multiwalled carbon nanotubes as solid phase absorbents followed by high performance liquid chromatography with diode array detector. Factors that maybe affect the enrichment efficiency of multiwalled carbon nanotubes such as the volume of eluent, sample flow rate, sample pH, and volume of the water samples were optimized. Under the optimal procedures, multiwalled carbon nanotubes as the absorbents have obtained excellent enrichment efficiency for atrazine and simazine. The detection limits of the atrazine and simazine were 33 and 9 ng l⁻¹, respectively. The spiked recoveries of the two analytes were over the range of 82.6-103.7% in most cases. Good analytical performance was achieved from real-world water samples such as river water, reservoir water, tap water and wastewater after primary pretreatment with proposed method. All these experimental results indicated that the developed method could be used as an alternative for the routine analysis of atrazine and simazine in many real water samples.     

Dispersive liquid–liquid microextraction combined with flow injection inductively coupled plasma mass spectrometry for simultaneous determination of cadmium, lead and bismuth in water samples

Dispersive liquid–liquid microextraction (DLLME) was combined with flow injection inductively coupled plasma mass spectrometry for simultaneous determination of cadmium, lead and bismuth in water samples. The metal elements were complexed with sodium diethyldithiocarbamate, and then the complexes were extracted into carbon tetrachloride by using DLLME. Under the optimized conditions, the enrichment factors for Cd, Pb and Bi are 460, 900 and 645 in 5 mL of a spiked water sample, respectively. The calibration graphs for the three metals are linear in the range of concentrations from <10 ng L^?1 to 1,000 ng L^?1. The detection limits are 0.5 ng L^?1, 1.6 ng L^?1 and 4.7 ng L^?1, respectively. The relative standard deviations for ten replicate measurements of 50 ng L^?1 cadmium, lead and bismuth are 2.6%, 6.7%, and 4.9%, respectively, and the relative recoveries in various water samples at a spiking level of 50 ng L^?1 range from 83.6% to 107.0%.     

A highly sensitive procedure for determination of ultra trace amounts of molybdenum by graphite furnace atomic absorption spectrometry after dispersive liquid-liquid microextraction

A simple, rapid and sensitive method is developed for selective determination of ultra trace amounts of molybdenum(V?) from different water samples. The method is based on highly efficient separation and pre-concentration of molybdenum(V?) by dispersive liquid-liquid microextraction followed by its determination with graphite furnace atomic absorption spectrometry. Ultra traces of the target ion were extracted and pre-concentrated from acidic water samples by using sodium diethyldithiocarbamate as a suitable chelating agent, and carbon tetrachloride and acetone as extraction and disperser solvents, respectively. After optimizing different parameters, including type and volume of extraction and disperser solvents, pH of test solution, extraction time, volume and concentration of the chelating agent and sample volume, an enrichment factor of 362 was obtained. The linear concentration range, limit of detection and relative standard deviation of the method were evaluated as 0.04–0.8 ng mL^?1, 0.007 ng mL^?1 and 4.5%, respectively. This method was applied successfully to the determination of molybdenum in tap water and wastewater samples.     

Determination of precious metals in geological samples by continuous powder introduction microwave induced plasma atomic emission spectrometry after preconcentration on activated carbon

A novel method was developed for analysing geological materials for Au, Ag, Pd and Pt by continuous powder introduction microwave induced plasma atomic emission spectrometry (CPI-MIP-AES). The preconcentration of the trace metals on activated carbon (AC) was performed before conducting MIP-AES measurements in order to obtain accurate and precise analytical results. The method proposed is based on the selective sorption of precious metals that are subsequently introduced to the plasma as a dry particulate aerosol consisted of analytes collected on the sorbent. The technical design and operating conditions of the novel sample introduction system based on the fluidized-bed concept has been optimized. The microwave excitation source with integrated rectangular cavity TE₁₀₁ and vertically positioned plasma torch has been used. The signal stability proved to be adequate for sequential mode of measurements due to the vertical plasma configuration as well as the MIP-AES system compatibility with the CPI technique. Calibration was done using home-made standards obtained by sorption of metals of interest from standard solutions on activated carbon. Precision is typically 1-4% relative standard deviation at the 1 μg g⁻¹ level. Under measurement conditions the detection limits for Ag, Au, Pd and Pt were 24, 43, 57 and 550 ng per 1 g of AC, respectively. The proposed procedure was used for Au, Ag, Pd and Pt determination in the platinum ore SARM-7 as well as Au and Ag in the Chinese soil GBW-07405 certified reference materials. The standard addition technique was used and recoveries revealed that the proposed method shows good accuracy and precision.     

Study of the preconcentration and determination of ultratrace rare earth elements in environmental samples with an ion exchange micro-column

A study was carried out on the preconcentration of ultratrace rare earth elements (REEs) in environmental samples with a micro ion-exchange column and determination by inductively coupled plasma mass spectrometry (ICP-MS). The preconcentration parameters were optimized and the REE recovery was ca. 100% in the pH range 4 to 6 with an ionic strength (μ) less than 0.18. The ion-exchange column capacity with respect to REEs was estimated as 0.96 mmol/g. The linear response coefficients ranged from 0.995 to 0.997 at the pg mL^–1 level. The concentration in the blank could be minimized (0.09 to 3.1 pg mL^–1) if the buffer solution and the water were purified. The detection limits ranged from 0.03 to 0.40 pg mL^–1, for a preconcentration factor of 100. The precision and accuracy of the method was evaluated with a synthetic standard solution and real samples. Results indicated that the REE recovery ranged from 88.1% to 100.2%, and the RSD ranged from 2.7% to 6.7%. Satisfactory results were achieved when this method was applied for the determination of REEs in raw water, purified water and tap water, as well as in environmental aquatic samples. Meanwhile, the method is simple and flexible.     

A study on adsorption of metals by activated carbon in a large-scale (municipal) process of surface water purification

Elements that enter the aquatic environment may pose a health risk to wildlife and humans. The aims of this study were: to determine how the introduction of activated carbon for a water purification system will improve the quality of the water produced; and to investigate the sorption of metals on activated carbons, including determination of the accumulation, as well as changes in concentrations of elements in carbons. The tests were carried out on three types of activated carbons with different granular structure. All samples were collected from Water Treatment Plant Goczalkowice, Poland. Concentrations of elements were measured using an optical emission spectrometer with inductively coupled plasma. The experiment showed that metals accumulating in the activated carbons during the operation included: Ca, Mn, Zn, and Cu. In each of the three types of carbons, it can distinguish such elements as Ba, Al, Cr, Ni, Ti, which are characterized by irregular accumulation during the operation of the filter. The introduction of carbon sorbent for water treatment largely contributed to improvement in the quality of raw material supplied to customers, mainly with regard to taste and smell, as well as to reduction of basic parameters: color, absorbance in the UV range and oxidability.      

Enrichment of pyrethroid residues in environmental waters using a multiwalled carbon nanotubes cartridge,and analysis in combination with high performance liquid chromatography

A sensitive method was developed using new carbon nanomaterial, multiwalled carbon nanotubes, as solid phase extraction adsorbents followed by high performance liquid chromatography with UV detection for determination of six pyrethroid pesticides at trace level in environmental water samples. Parameters influencing the extraction efficiency were investigated in detail. Under the optimal conditions, detection limits of 0.7–5.0 ng L⁻¹ were obtained for six pyrethroid pesticides, the linear ranges were between 0.1 and 40 μg L⁻¹ and the precisions were in the range of 2.0–5.8%. The method has been applied to determine the six target compounds in tap water, well water, river water and reservoir water. Good recoveries were obtained for all target analytes and these results indicated that the method developed can be used in the determination of such compounds at trace levels in environmental water samples.

     

活性炭富集-电热塞曼原子吸收光谱法测定水中痕量的汞

建立了一种水中痕量汞的测定方法。通过活性炭定量吸附水中痕量汞,采用电热塞曼原子吸收光谱法测定活性炭富集的汞。与目前水中总汞测定方法相比,本方法避免了消解等步骤,减少了汞污染和汞损失,操作更加简单。考察了活性炭粒度、酸处理方法、酸介质和富集时间对富集效率的影响,以及热解温度和干扰离子对方法测定结果的影响。通过空白活性炭加标、空白溶液加标和环境水样加标3种方法制作标准曲线,三者的相关系数达0.9999,经统计检验,3条标准曲线的斜率无差异,表明了在此实验条件下环境水样中的共存物不干扰汞的测定,同时也表明可直接用空白活性炭加标的方法进行标准曲线的绘制。采用本方法对含5和50 ng/L汞的水样进行测定,其相对标准偏差分别为7.2%和4.2%(n=11)。本方法测定下限达到1.2 ng/L。地表水和自来水样中添加10 ng/L汞的加标回收率在92.0%~103.0%之间。用 ICP-MS作对照,二者分析结果相符合,相对误差在2.9%~ 3.4%之间,表明本方法准确可靠、精密度好。     

Determination of arsenic and antimony in milk by hydride generation atomic fluorescence spectrometry

A highly sensitive procedure has been developed for total arsenic and antimony determination in milk samples by hydride generation atomic fluorescence spectrometry after microwave-assisted sample digestion. The discrete introduction of 2 ml of digested sample in the automated continuous flow hydride generation system allows us to reduce drastically the sample and HCl consume and to determine several elements from a same sample digestion. The method provides detection limits of 0.006 and 0.003 ng ml⁻¹, a sensitivity of 2390 and 2840 fluorescence units per ng ml⁻¹ for As and Sb respectively, and average relative standard deviation of 2.3% for As and 4.8% for Sb. The analysis of cow milk samples, obtained from the Spanish market evidenced the presence of As at concentration levels from 3.4 to 11.6 ng g⁻¹ and Sb levels from 3.5 to 11.9 ng g⁻¹, thus in a proportion near to 1:1, which is in contrast with the 10:1 natural ratio between As and Sb and could evidence the effect of the introduction of new alloys and polymer materials in the industrial process of milk. The method was validated by the comparison of data found for commercial samples by using the proposed procedure and reference methods based on dry-ashing and AFS, and microwave-assisted digestion and inductively coupled plasma mass spectrometry determination.     

Multiwalled Carbon Nanotubes as SPE Adsorbents for Simultaneous Determination of Seven Sulfonylurea Herbicides in Environmental Water by LC–MS–MS

An effective and rapid method was developed for simultaneous determination of seven sulfonylurea herbicides in environmental water using multiwalled carbon nanotubes as solid-phase extraction sorbent coupled with liquid chromatography–tandem mass spectrometry. Important parameters influencing the extraction efficiency such as pH of the sample solution, flow rate of sample loading, the eluent and its volume were optimized. Under optimum conditions, good linearity was obtained for all herbicides (r ² > 0.99) over the range of 0.05–5,000 ng L^?1, and precisions (RSD) for nine replicate measurements of a standard mixture of 200 ng L^?1 were 1.9–7.4%. The limits of detection and quantification were 0.01–0.20 and 0.05–1.00 ng L^?1, respectively. The proposed method was successfully applied to the analysis of tap water, spring water, ground water and well water, and mean recoveries for seven analytes at three spiked concentration levels were from 81.5 to 110.5% with RSDs between 0.3 and 7.0%. The results showed that the established method has wide application to analyze sulfonylurea herbicides at trace level in water.     

Application of iminodiacetate chelating resin muromac A-1 in on-line preconcentration and inductively coupled plasma optical emission spectroscopy determination of trace elements in natural waters

On-line system incorporating a microcolumn of Muromac A-1 resin was used for the developing of method for preconcentration of trace elements followed by inductively coupled plasma (ICP) atomic emission spectrometry determination. A chelating type ion exchange resin has been characterized regarding the sorption and subsequent elution of 24 elements, aiming to their preconcentration from water samples of different origins. The effect of column conditioning, pH and flow rate during the preconcentration step, and the nature of the acid medium employed for desorption of the retained elements were investigated. A sample (pH 5) is pumped through the column at 3 ml min⁻¹ and sequentially eluted directly to the ICP with 3 M HNO₃/HCl mixtures. In order to remove residual matrix elements from the column after sample loading a short buffer wash was found to be necessary. The effectiveness of the matrix separation process was illustrated. The procedure was validated by analyzing several simple matrices, Standard River water sample as well as artificial seawater. Proposed method can be applied for simultaneous determination of In, Tl, Ti, Y, Cd, Co, Cu and Ni in seawater and for multielement trace analysis of river water. Recovery at 1 μg l⁻¹ level for the determination of investigated 24 elements in pure water ranged from 93.1 to 96% except for Pd (82.2%) and Pb (88.1%). For the same concentration level for seawater analysis recovery was between 81.9 and 95.6% except for Hg (38.2%).     

Trace Enrichment and Atomic Absorption Spectrometric Determination of Lead,Copper, Cadmium and Nickel in Drinking Water Samples by Use of an Activated Carbon Column

Abstract

A simple method for atomic absorption spectrometric determination of lead, copper, cadmium and nickel in drinking water samples after preconcentration by sorbing 1-(2-pyridylazo) 2-naphthol (PAN) complex of these metals on an activated carbon column has been established. The metal/PAN complexes were quantitatively retained on the activated carbon in the pH range 6-8. Metals retained on the activated carbon column were completely eluted with 2M HCl in acetone. This method was applied to the determination of lead, copper, cadmium and nickel in drinking water samples and good results were obtained (Recoveries >95%, relative standard deviations <7%, relative error <3%).