Time-resolved laser-induced fluorimetry for screening polycylic aromatic hydrocarbons on solid-phase extraction membranes

The potential of solid-phase extraction (SPE) time-resolved laser-induced fluorimetry (TRLIF) is evaluated for screening polycyclic aromatic hydrocarbons (PAHs) in aqueous samples. Octadecyl membranes are used with the dual purpose of extracting the pollutants from the water sample and serving as the solid substrate for fluorescence detection. Excitation of fluorescence is performed with a Nd:YAG pumped tunable dye laser pumped with a pulsed source for time-resolving spectral interference. Wavelength time matrices (WTMs) and real time-resolved fluorescence spectra are recorded with a pulsed delay generator, a spectrograph and an intensified charge-coupled device (ICCD). In comparison to SPE solid-matrix luminescence (SML) with conventional instrumentation, this approach provides better limits of detection (LOD) and selectivity. The improvement in LOD is of one order of magnitude, reaching the parts-per-trillion level with 10 ml of water sample. The improvement in selectivity allows the direct determination of target compounds in complex samples. The direct determination of benzo[a]pyrene from a spiked river water sample of unknown composition is presented.     

Chemical analysis of polycyclic aromatic hydrocarbons by surface-enhanced Raman spectroscopy

The use of surface-enhanced Raman spectroscopy (SERS) for trace determination of polycyclic aromatic hydrocarbons (PAHs) is described. This paper focuses on the development of SERS-active substrates that are specific for the characterization and spectroscopic study of PAHs. The SERS-active substrates are based on thin gold films evaporated on a glass surface previously treated with a mercaptoalkylsilane. SERS of PAHs was investigated over uncoated gold island films and over such films coated with a self-assembled monolayer (SAM) of 1-propanethiol. Adsorption of PAHs on a plain SERS-active Au-film led to a surface-induced decomposition of PAHs, due to catalytic properties of nanostructured gold. Thus, the functionalization of the SERS-active substrates by means of SAM was done aiming at a specific chemical interaction toward PAHs. Thus, in addition to preventing decomposition of the PAHs, the coating also concentrates the hydrophobic PAHs close enough to the SERS-active interface. Results show that high sensitivity, SERS-active nanostructured gold substrates that show selectivity towards PAHs were obtained, with the following properties: strong intensification of the Raman signal, reproducibility, and stability over time. The employed methodology enables the observation of excellent Raman spectra of PAHs in aqueous environment at ppm levels.     

Solid-surface phosphorescence characterization of polycyclic aromatic hydrocarbons and selective determination of benzo(a)pyrene in water samples

This paper presents the phosphorescence characterization of polycyclic aromatic hydrocarbons (PAHs) on solid-surface for obtaining new flow-through phosphorescence optosensors for PAHs-based on-line, immobilized onto a non-ionic resin solid support coupled to a continuous flow system and the applications for the selective determination of benzo(a)pyrene (BaP). The phosphorescent characterization of 15 PAHs, described as major pollutants by the Environmental Protection Agency (EPA) (naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, chrysene, benzo(a)anthracene, benzo(k)fluoranthene, benzo(b)fluoranthene, benzo(a)pyrene, indeno(1,2,3-cd)pyrene, benzo(g,h,i)perylene and dibenzo(a,h)anthracene) has been carried out. The experimental variables (heavy atom, deoxygenation and organic solvent in samples) for obtaining different possibilities for developing mono and multi-parameter PAH sensors and the conditions for PAH screening have been carefully studied and the experimental conditions to determination of BaP in presence of other PAHs in water samples have been optimized.     

Determination of 252–302 Da and tentative identification of 316–376 Da polycyclic aromatic hydrocarbons in Standard Reference Materials 1649a Urban Dust and 1650b and 2975 Diesel Particulate Matter by accelerated solvent extraction–HPLC-GC-MS

We have assessed and compared the extraction recoveries of polycyclic aromatic hydrocarbons (PAHs) with molecular weights of 252, 276, 278, 300 and 302 from diesel particulate matter (PM) and urban air particles using ultrasonically assisted extraction and accelerated solvent extraction methods, and evaluated the effects of sample and treatment parameters. The results show that accelerated solvent extraction can extract PAHs more efficiently from diesel PM than ultrasonically assisted extraction. They also show that PAHs are more difficult to extract from diesel PM than from urban air particles. Using toluene and maximum instrumental settings (200 °C, 3,000 psi and five extraction cycles) with 30-min static extraction times > 85% of the analytes were estimated to be extracted from the diesel particles, but four extraction cycles with just 5-min static extraction times under these conditions seem to be sufficient to extract > 95% of the analytes from the urban air particles. The accelerated solvent extraction method was validated using the Standard Reference Materials (SRM) 1649a, Urban Dust, and SRM 2975 and SRM 1650a, Diesel Particulate Matter, from the US National Institute of Standards and Technology (NIST). PAH concentrations determined by on-line high-performance liquid chromatography–gas chromatography–mass spectrometry (HPLC-GC-MS) following the developed accelerated solvent extraction method were generally higher than the certified and reference NIST values and concentrations reported in the literature (e.g. the estimated concentration of benzo[a]pyrene in SRM 2975 was 15-fold higher than the NIST-certified value), probably because the extraction recoveries were higher than in previous studies. The developed accelerated solvent extraction method was used to analyse high molecular (HMW) weight PAHs (MW > 302) in the investigated SRMs, and more than 170 (SRM 1649a), 80 (SRM 1650b) and 60 (SRM 2975) potential high molecular weight PAHs were tentatively identified in them, with molecular weights (depending on the SRM sample analysed) of 316, 326, 328, 340, 342, 350, 352, 366, 374 and 376. This is, to our knowledge, the first study to tentatively report PAHs with molecular weights of 316, 326, 328, 342, 350, 352, 366 and 376 in diesel particulate matter. GC-MS chromatograms obtained in selected ion monitoring mode (extracted ions for the abovementioned m/z) and full-scan mass spectra of tentatively identified high molecular weight PAHs are shown in the Electronic supplementary material. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Highly sensitive and selective fluorescence optosensor to detect and quantify benzo[a]pyrene in water samples

We describe here a method for detecting and quantifying the highly carcinogenic polycyclic aromatic hydrocarbon (PAH) benzo[a]pyrene (BaP) in water, based on a flow-trough optical sensor. The technique is fast (response time of 40 s) and simple and at the same time meets the standards of sensitivity and selectivity required by the European Guidelines on Water for Human Consumption. The optosensor is based on the on-line immobilization of BaP on a non-ionic resin (Amberlite XAD-4) solid support in a continuous-flow system. BaP was analyzed in a 15 mM H₂PO₄⁻/HPO₄²⁻ buffer solution with 25% (v/v) 1,4-dioxane at pH 7. Fluorescence intensity was measured at λ_ex/em=392/406 nm. The experimental conditions (reagent phase, pH, type and concentration of buffer solution and organic solvent) and flow-injection values (flow rate and injection volume) were carefully controlled. Under these conditions the optosensor was sensitive to a linear concentration range of between 3.0 and 250.0 ng l⁻¹ with a detection limit of 3.0 ng l⁻¹ and a standard deviation of 1.5% at 150 ng l⁻¹. The optosensor was applied to the quantification of BaP in drinking and waste water samples (95-105% recovery) in presence of the other 15 EPA PAHs at 1000 ng l⁻¹ concentration level. The influence of other fluorescent polycyclic aromatic hydrocarbons and potential interference from ions usually present in water was also evaluated.     

Determination of trace amounts of polycyclic aromatic hydrocarbons in soil

A method for monitoring the contamination of soil with polycyclic aromatic hydrocarbons (PAHs) is introduced. Drying at elevated temperature is omitted to avoid losses of the more volatile constituents (primarily naphthalene). The soil sample, including its natural water content, is extracted with 2-methoxyethanol and cleaned up using a disposable C₈ cartridge and the PAHs are eluted with pentane, concentrated and measured by capillary gas chromatography with flame ionization detection. Determination limits between 15 and 35μg kg^?1 are obtained and the recovery is 80–90% measured at the 125 μg kg^?1 spike level, except for naphthalene (66%). Special attention is given to the design of the spiking technique, which simulates natural incorporation as far as possible, takes account of evaporation losses and therefore allows “real” recovery rates to be determined.     

α-Oxoketene dithioacetal mediated aromatic annulation: highly efficient and concise synthetic routes to potentially carcinogenic polycyclic aromatic hydrocarbons

Highly efficient regiospecific routes to potentially carcinogenic polycyclic aromatic hydrocarbons such as substituted benzo[c]phenanthrenes, benzo[c]fluorenes, 16,17-dihydro-11-methyl-15[H]cyclopenta[a]phenanthrene, 5-methyl-7,8,9,10-tetrahydrochrysene and 1,4-dimethylphenanthrene have been developed. The overall strategy involves our aromatic annulation protocol through base induced conjugate addition-elimination on the cyclic and acyclic α-oxoketene dithioacetals with the appropriate arylacetonitriles followed by acid induced cyclodehydration of the resulting conjugate adducts. Subsequent reductive dethiomethylation (Raney Ni) and dehydrogenation (DDQ) of the cyclized products affords the methyl substituted PAHs in high yields.     

北京地区大气颗粒物中不同功能区多环芳烃的分布特征

用撞击式分级采样器同步采集了北京市城乡结合部、郊区的2003年四个季节的不同粒径大气颗粒物样品,用气相色谱-质谱分析了其中的多环芳烃。两个功能区的PAHs总质量浓度分布趋势均为：冬季>秋季>春季>夏季;不同环数PAHs在不同粒径颗粒物中的分配比例比较显示,粗颗粒物中2 环或3环PAHs的分配比例比其在高环PAHs的比例要大。     

气相色谱质谱法测定化妆品中9种多环芳烃

建立了气相色谱质谱法测定化妆品中9种多环芳烃的分析方法。化妆品中的萘、苯并[a]蒽、、苯并[b]荧蒽、苯并[j]荧蒽、苯并[k]荧蒽、苯并[e]芘、苯并[a]芘、二苯并[a,h]蒽等9种多环芳烃用甲醇超声提取后,用环己烷液-液萃取后浓缩,经硅胶-中性氧化铝柱净化后,采用气相色谱-质谱测定。多环芳烃浓度在0.05～2 mg/L范围内,质量浓度与其峰面积呈良好的线性关系。在低、中、高3个添加水平下,9种多环芳烃化合物的平均回收率为81.6%～100.2%,相对标准偏差为1.3%～5.8%。方法可用于化妆品中多环芳烃的检测。     

Evaluation of polycyclic aromatic hydrocarbons in gasoline by HPLC and GC-MS

Summary In this paper the evaluation of polycyclic aromatic hydrocarbons (PAHs) in gasoline is described. A procedure involving a double extraction of samples with N-methylpirrolidone-water-phosphoric acid and with cyclohexane has been used followed by HPLC-DAD and GC-MS. The results obtained show that all gasoline samples contain PAHs with two to six rings and no substantial difference was noticed between leaded and unleaded gasoline. The benzo(a)-pyrene content ranged between 1.0–2.0 mg L⁻¹, a comparatively high concentration for a dangerous compound.     

Analysis of polycyclic aromatic hydrocarbons adsorbed on particles of atmospheric interest using pressurised fluid extraction

Pressurised fluid extraction (PFE) was used for the measurement of 13 polycyclic aromatic hydrocarbons (PAHs) adsorbed on different types of particles: two model particles (PAH-coated silica, PAH-coated graphite) and two natural atmospheric particles (urban dust and diesel exhaust, from NIST reference materials). Samples were analysed by gas chromatography coupled to mass spectrometry. Extraction efficiency was evaluated with internal standard recovery yields and was shown to depend on the nature of the particle, on the structure of the analytes and on the PAH concentration. Extraction conditions (toluene, 130°C, 130 bar, 2 × 8-min static cycles) were optimised to extract PAHs when strongly interacting with solid matrices and were validated by the analysis of two PAH-certified materials.     

Characterisation of polycyclic aromatic hydrocarbons in atmospheric aerosols by gas chromatography-mass spectrometry

An accurate and reliable method for determining polycyclic aromatic hydrocarbons (PAHs) in atmospheric aerosols is described. This optimised gas chromatography-mass spectrometry (GC-MS) method permits a wide range of concentrations to be analysed without the influence of interferences.Pre-treatment comparison of four kinds of aerosol collector filters determined that quartz and glass fibre filters were the most suitable. Solvents like cyclohexane, toluene, acetonitrile and dichloromethane were evaluated for their PAH-extraction capacity. Ultrasonic extraction using CH₂Cl₂ was selected because it is rapid and easy; moreover, this solvent increases the sample-throughput capacity.PAH compounds were quantitatively collected and ultrasonically extracted twice using 15 mL of CH₂Cl₂ for 15 min for each replicate. Rotavapor concentration, fractionation and dissolution were also optimised.A certified standard mixture (16 EPA PAHs), a deuterated compound and precision recovery assays were used for validating the proposed methodology. Adequate analytical parameters were obtained. Detection limits were (1.6-26.3) × 10⁻⁵ ng and quantification limits were (5.2-87.6) × 10⁻⁵ ng.Analysis of the environmental samples detected 4-10 EPA list PAH compounds. In addition, 2-11 tentative compounds were found, and their molecular structures were described for the first time.Our study of both Youden method and the standard addition method has shown that the proposed determination of PAHs in environmental samples is free of systematic errors.In conclusion, this unbiased methodology improves the identification and quantification of PAH compounds. High sensitivity as well as acceptable detection and quantification limits were obtained for the environmental applications.     

A selective method for the determination of benzo[a]pyrene in soil using porous graphitic carbon liquid chromatography columns

A back-flushing procedure using porous graphitic carbon (PGC) HPLC columns has been used successfully for the cleanup of soil samples for the determination of benzo[a]pyrene in ppb levels by an ODS-fluorescence HPLC column. The procedure was tested on nine random soil samples taken from an industrial area of the Kingdom of Bahrain. The mean percent recovery from the PGC column was 96% and the average coefficient of variation for the whole method was 5.2%.     

Identification and characterization of polycyclic aromatic hydrocarbons in coking wastewater sludge

GC‐MS analysis was performed on the coking sludge from a coking wastewater treatment plant (WWTP) to allow detailed chemical characterization of polycyclic aromatic hydrocarbons (PAHs). The identification and characterization of the isomers of PAHs was based on a positive match of mass spectral data of their isomers with mass spectra databases or based on a comparison of electron impact ionization mass spectra and retention times of target compounds with those reference compounds. In total, 160 PAH compounds including numerous N‐, O‐, S‐, OH‐, and Cl‐containing derivatives were positively identified for the first time. Quantitative analysis of target compounds was performed in the selected ion‐monitoring mode using the internal standard method. The total concentrations of selected compounds in the coking sludge samples from the anaerobic tank, aerobic tank, hydrolytic tank, and secondary clarifier of the WWTP ranged from 1690 ± 585 to 6690 ± 522 mg/kg, which were much higher than those in other industrial and municipal sludges. PAHs with four and five rings were found to be the dominant compounds, and diagnostic ratios of these compounds suggested that they had the characteristics of coal combustion and pyrolysis.     

Isotope dilution determination of polycyclic aromatic hydrocarbons in olive pomace oil by gas chromatography-mass spectrometry

A gas chromatographic (GC) method with mass spectrometry detection (MS) for the determination of eight polycyclic aromatic hydrocarbons (PAHs) in olive pomace oil has been developed. The oil was diluted with n-pentane and extracted by liquid-liquid partition with dimethyl sulphoxide (DMSO). After water addition and back-extraction with cyclohexane, a thin-layer chromatography on silica gel was performed as a further purification step. The PAHs spot was scraped off from the plate and the final extract was concentrated and analysed by GC-MS in full scan mode. The eight PAHs under investigation were determined in the presence of the corresponding labelled compounds added as internal standards to the sample at the beginning of the analytical process. The identified PAHs were then quantified by the isotope dilution methodology assuring the compensation of the concentration of each analyte for any variation in the sample preparation. The method precision was satisfactory with relative standard deviation (R.S.D.) values in the range 3.6-12.7% for all PAHs. The average recovery rates ranged from 69.0 to 97.5%. Accuracy was also calculated for benzo[k]fluoranthene, benzo[a]pyrene, indeno[1,2,3-cd]pyrene and benzo[ghi]perylene by analysing a certified reference material (CRM 458, coconut oil) with adequate results. All response curves exhibited a linear fit from 0.1 to 10 microg ml(-1) and the determination coefficients R2 were better than 0.9942. The limits of detection (0.1-0.4 microg kg(-1)) were acceptable when compared with the maximum permitted limit of 2 microg kg(-1) for each of the eight considered PAHs and 5 microg kg(-1) for the sum of the eight PAHs established by the Italian legislation. Measurement uncertainty was finally calculated identifying and quantifying the uncertainty components of the analytical process. The relative expanded uncertainties (Uc), expressed as percent values were in the range 8.5-11.4% thus appropriate for residues quantification in the range of concentrations considered in the present study.     

Polydimethylsiloxane‐coated partitioning sample collection device for the precise quantification of polycyclic aromatic hydrocarbons in air

A novel partitioning collection device comprising a glass cartridge packed with poly(dimethylsiloxane)‐coated macroporous silica particles was developed for the precise quantification of polycyclic aromatic hydrocarbons in air. The analyte collection and elution performances achieved using different amounts of poly(dimethylsiloxane) coating were quantitatively evaluated. The sample retention power increased with increasing the coating, and more than 250 L of air could be collected without analyte breakthrough at a sampling temperature of 35°C. During the air collection, the moisture in the air was not retained on the particles due to the hydrophobic surface of the sorbent. A complete and rapid elution of the collected analytes from the device was accomplished by the passage of only 10 mL of acetone with ultrasonication for 1 min. The proposed method was successfully applied for the determination of airborne polycyclic aromatic hydrocarbons in tunnel air.     

Solubility prediction of polycyclic aromatic hydrocarbons in non-aqueous solvent mixtures

This study is aimed at evaluating the applicability of the Jouyban–Acree model for predicting the solubility of polycyclic aromatic hydrocarbons (PAHs) in binary and ternary solvent mixtures at different temperatures by employing a large solubility data set. The solubility is predicted in solvent mixtures at different temperatures within an acceptable error range based on the experimental solubility data of PAHs in mono-solvents. The results reveal that the Jouyban–Acree model could be recommended for practical applications in chemical industries.     

改进QuEChERS-气相色谱-质谱法快速分析测定农用土壤中多环芳烃

建立农用土壤中16种多环芳烃的改进QuEChERS快速提取净化方法及气相色谱-质谱检测方法,并通过对西安市周边农用土壤样品的分析,调查土壤中多环芳烃的污染情况.土壤样品用KOH饱和的甲醇碱化处理后,用丙酮-正已烷(1+1)为提取溶剂,涡旋混匀后超声提取,提取液按改进QuEChERS方法加入无水MgSO4、硅胶及正丙基乙二胺(PSA)进行净化,检测时选用DB -5 MS(30m×0.25 mm×0.25 μm)色谱柱分离,EI电离源及离子监测模式检测,16种多环芳烃的测定低限0.7～3.2μg/kg,加标回收率79.8％ ～ 109.6％,相对标准偏差均低于9.4％.检测的农用土壤样品中均检出有不同程度的多环芳烃残留,约16.7％的土壤样品为轻度污染.     

Headspace solvent microextraction and gas chromatographic determination of some polycyclic aromatic hydrocarbons in water samples

Headspace solvent microextraction (HSME) was shown to be an efficient preconcentration method for extraction of some polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions. A microdrop of 1-butanol (as extracting solvent) containing biphenyl (as internal standard) was used in this investigation. Extraction occurred by suspending a 3 μl drop of 1-butanol from the tip of a microsyringe fixed above the surface of solution in a sealed vial. After extraction for a preset time, the microdrop was retracted back into the syringe and injected directly into a GC injection port. The effects of nature of extracting solvent, microdrop and sample temperatures, stirring rate, microdrop and sample volumes, ionic strength and extraction time on HSME efficiency were investigated and optimized. Finally, the enrichment factor, dynamic linear range (DLR), limit of detection (LOD) and precision of the method were evaluated by water samples spiked with PAHs. The optimized procedure was successfully applied to the extraction and determination of PAHs in different water samples.