PMMA films refractive index modulation via TiO2 nanoparticle inclusions and corona poling

The present study is focused on the characterization of optical properties of poly (methyl methacrylate) (PMMA) films and the possibilities of modulation and fine tuning of their refractive index by the inclusion of different concentrations of nano-sized titanium dioxide (TiO₂) particles (less than 33 nm) and corona poling. The samples are prepared by the “spin coating” method and they are charged in a conventional point-to-plain corona system. The transparent PMMA/TiO₂ films exhibit good optical properties in the visible range. An investigation of the film’s surface refractive index by two wavelengths laser refractometry utilizing the disappearing diffraction pattern method is carried out. The refractive index increases with increasing the TiO₂ content in the nanocomposite films. The corona poling increases the refractive index values for all samples regardless of the polarity and concentration of TiO₂ nanoparticles. The results show that the prepared nanocomposite films have a potential application for optical devices.     

Study on optical interference effect of graphene oxide films on SiO2 and Si3N4 dielectric films

The optical interference effect has enabled the visualization of thin layers, even monolayers, of graphene by simple optical microscopy. In this study, we have controlled the optical interference effect by changing the thickness and types of dielectric films, i.e. SiO₂ and Si₃N₄. By investigating differences in RGB parameters between the graphene oxide layer and the dielectric layer, conditions for the highest visibility of the graphene oxide layer were determined. We also studied colors as a function of graphene oxide layer thickness and dielectric layer thickness. These color patterns can be effectively presented as two-dimensional color charts. When comparing SiO₂ and Si₃N₄ as dielectric layers, each layer was found to exhibit different interference fringe patterns, which is due to a mismatch of optical properties between the material layer and dielectric layer. The effects of optical properties (n, k) of the material layer on interference colors were also investigated.     

Films of certain oxides of rare-earth elements as the activators of platinum electrode on ZrO<Subscript>2</Subscript> + 10 mol % Y<Subscript>2</Subscript>O<Subscript>3</Subscript> electrolyte

The characteristics of porous Pt/YSZ (ZrO₂ + 10 mol % Y₂O₃) electrodes activated with small amounts of either oxides of rare-earth elements (REE) of the cerium subgroup (CeO₂, PrO _x , TbO _x ) or a mixed oxide with the Сe₂Tb₄O₁₁ composition by the procedure of impregnating the electrodes with ethanol solutions of REE nitrates and subsequent heating at 850°С are studied by the impedance method. The studies are carried out for those cases where the REE oxides after thermal treatment form a film on the electrolyte and also where no activator film is formed. The characteristics of films and activated electrodes are compared. Film-activated Pt/YSZ electrodes are discussed within the framework of the model of compact oxide electrodes.     

Surface characteristics of anodic oxide films fabricated in acid and neutral electrolytes on Ti–10V–2Fe–3Al alloy

Anodic oxide films were fabricated on Ti–10V–2Fe–3Al alloy in acid (H₂SO₄/H₃PO₄) and neutral environmental friendly (C₄H₄O₆Na₂) electrolytes. The morphology, roughness, crystalline structure of the anodic oxide film were characterized by using scanning electron microscopy, atomic force microscopy, Raman spectroscopy and electrochemical impedance spectroscopy (EIS). The results showed that the oxide film fabricated in H₂SO₄/H₃PO₄ electrolyte had a porous structure and the thickness of the film was 3.5 µm. The oxide film fabricated in C₄H₄O₆Na₂ electrolyte presented a nonporous structure that sustained the evident microstructure of the substrate, and the thickness of the film was 6.0 µm. The surface average roughness values of the two types of films were 245 nm and 166 nm, respectively. The phase of the anodic oxide films consisted mainly of anatase and rutile. EIS results showed that the film fabricated in C₄H₄O₆Na₂ electrolyte had higher impedance of the outer layer, while the film fabricated in H₂SO₄/H₃PO₄ electrolyte had higher impedance of the inner layer. Moreover, we attempt to explain the differences in the anodizing kinetics, structure and electrochemical impedance of anodic oxide films by the different films growth processes in the two types of electrolytes. Copyright © 2012 John Wiley & Sons, Ltd.     

Composition and properties of CeO2-SiO2 composite films prepared from film-forming solution

This study focuses on the preparation and properties of CeO₂-SiO₂ thin films with thickness ≤60 nm that can be used as protective coatings for solar cell panels and electrochromic counter electrodes. Thin-film CeO₂-SiO₂ systems on glass and quartz substrates, which are manufactured from film-forming solutions based on cerium(III) nitrate, salicylic acid, and tetraethoxysilane and thermally treated, are mixtures of cerium(IV) (cubic modification) and silicon(IV) (amorphous phase) oxides. The films synthesized are distinguished by a net structure and high visible transmittance (～90-100%). The morphology, phase composition, and optical properties of films were studied by X-ray diffraction, X-ray spectral microanalysis, scanning electron microscopy, spectrophotometry, and ellipsometry.     

Modification of niobium surfaces using plasma electrolytic oxidation in silicate solutions

Herein, a study of the plasma electrolytic oxidation (PEO) of niobium in an anodising bath composed of potassium silicate (K₂SiO₃) and potassium hydroxide (KOH) is reported. The effects of the K₂SiO₃ concentration in the bath and the process voltage on the characteristics of the obtained oxide layers were assessed. Compact, barrier-type oxide layers were obtained when the process voltage did not exceed the breakdown potential of the oxide layer. When this threshold was breached, the morphology of the oxide layer changed markedly, which is typical of PEO. A significant amount of silicon, in the form of amorphous silica, was incorporated into the oxide coatings under these conditions compared with the amount obtained with conventional anodising. This surface modification technique led to an improvement in the corrosion resistance of niobium in Ringer’s solution, regardless of the imposed process conditions.     

Effect of sulfate and dissolved hydrogen on oxide films on stainless steel in high-temperature water

In the present paper, we focus on the influence of sulfate ion impurity and dissolved hydrogen on the protective ability of the oxide film on stainless steel in high-temperature water. For the purpose, the electrical and electrochemical properties of oxide films formed on AISI 316L NG in simulated boiling water reactor crack conditions (10 ppm sulfate purged with N₂ + 0.01 or 0.5% H₂) were characterized by in situ electrochemical impedance spectroscopy (EIS). In addition, the surface and in-depth composition of the oxide films has been estimated by ex situ Auger electron spectroscopy (AES). The quantitative assessment of the protective ability of the oxide is based on an interpretation of the electrochemical impedance data per the mixed-conduction model. A novel procedure for the estimation of kinetic and transport parameters that involves comparison of the model equations to both EIS and AES results is proposed and tested. Based on the parameter values, the effect of sulfate and dissolved hydrogen on the processes of film growth and dissolution is discussed in view of an approach to the initiation of stress corrosion cracks.     

Synthesis and properties of films in the SiO2-Bi2O3 system

The compositions of film-forming solutions for synthesizing films in the SiO₂-Bi₂O₃ system were determined (10–90 mol % Bi₂O₃). The obtained films are characterized by high dielectric constants (2.43–7.89). It was demonstrated how the quantitative ratio between SiO₂ and Bi₂O₃ in the films and powders affects their phase composition, refractive index, and dielectric constant and the acid-base properties of the surface.     

Direct electrochemistry and electrocatalysis of hemoglobin on a glassy carbon electrode modified with poly(ethylene glycol diglycidyl ether) and gold nanoparticles on a quaternized cellulose support. A sensor for hydrogen peroxide and nitric oxide

A glassy carbon electrode was modified with gold nanoparticles (Au-NPs) on a quaternized cellulose support in a film composed of poly(ethylene glycol diglycidyl ether) (PEGDGE), and Hb was immobilized on the Au-NPs. The sensor film was characterized by UV–vis spectra, scanning electron microscopy, and electrochemical impedance spectroscopy. Cyclic voltammetry of the Hb in the Au@Qc/PEGDGE film revealed a pair of well-defined and quasi reversible peaks for the protein heme Fe(III)/Fe(II) redox couple at about ?0.333 V (vs. SCE). The sensor film also exhibited good electrocatalytic activity for the reduction of nitric oxide and hydrogen peroxide. The amperometric response of the biosensor depends linearly on the concentration of nitric oxide in the 0.9 to 160 μM range, and the detection limit is as low as 12 nM (at 3σ). The response to hydrogen peroxide is linear in the 59 nM to 4.6 μM concentration range, and the detection limit is 16 nM (at 3σ). This biosensor is sensitive, reproducible, and long-term stable. Figure

An electrochemical biosensor based on the immobilization of hemoglobin in Au@Qc NPs /Poly ethylene glycol diglycidyl ether composite film is developed.     

Sensitive determination of nitric oxide using an electrochemical sensor based on MWCNTs decorated with spherical Au nanoparticles

This paper describes the synthesis, characterisation and application of a very sensitive electrochemical sensor based on a glassy carbon electrode modified with multiwalled carbon nanotubes (MWCNTs) decorated with homogeneously distributed spherical gold nanoparticles (AuNPs). These AuNPs presented diameters ranging from 2 to 10 nm. The AuNPs were prepared directly on the MWCNTs’ surface via a synthesis using HAuCl₄ and citric acid as the reducing agent. The resulting material (Au/MWCNTs) was characterised by scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDX), high-resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD) and Raman spectroscopy. The developed Au/MWCNTs sensor was used in the determination of nitric oxide (NO) in phosphate buffer solution at pH 4.4 by differential pulse voltammetry. In the potential window between 0.5 and 0.65 V, a well-defined oxidation peak was observed, whose height was proportional to the NO concentration in the solution. The Au/MWCNTs-modified electrode exhibited high sensitivity for the determination of nitric oxide, with the limit of detection being 0.21 nmol L^?1 (S/N?=?3). No significant interference was detected for nitrite and CO₂ in the NO detection. Our study demonstrated that the resultant Au/MWCNT-modified electrode can be used for nitric oxide detection in the presence of ascorbic acid, dopamine and uric acid, being potentially useful for determinations of NO in real samples. Figure

?     

Synergistic effect of additional TiO2 support on metathesis activity of ethylene and 2-butene over supported tungsten-based catalysts for propylene production

Tungsten-based catalysts of different preparations mixed with TiO₂ support were investigated in the metathesis of ethylene and trans-2-butene to propylene. The catalytic activity of silica-supported tungsten oxide catalyst (WO₃/SiO₂) mixed with TiO₂ additional support had higher efficiency than that of mixed SiO₂-TiO₂ supported tungsten oxide (WO₃/SiO₂-TiO₂). The clean area of the TiO₂ additional support, which provides more space for tungsten migration, is an important key to explain the improved catalytic activity, due to the higher fraction of the isolated surface tetrahedral tungsten oxide species and better dispersion of the tungsten oxide species observed by FT Raman spectroscopy. In addition to the synergistic effect of the additional TiO₂ support on the metathesis activity, the similar synergy was also observed for the one–third diluted catalysts with additional SiO₂. It has been found that the synergistic effect exerted by the presence of additional SiO₂ support predominates over the one-third dilution effect of catalyst concentration. Thus, adding an additional support is another simple way to improve the catalytic activity of the catalysts and makes great benefit for being used in real chemical industry.     

Estimation of kinetic parameters for the phase change memory materials by DSC measurements

The non-isothermal method for estimating the kinetic parameters of crystallization for the phase change memory (PCM) materials was discussed. This method was applied to the perspective PCM material of Ge₂Sb₂Te₅ with different Bi contents (0, 0.5, 1, 3 mass%) for defining the kinetic triplet. Rutherford backscattering spectroscopy and X-ray diffraction were used to carry out elemental and phase analysis of the deposited films. Differential scanning calorimetry at eight different heating rates was used to investigate kinetics of thermally induced transformations in materials. Dependences of activation energies of crystallization (E _a) on the degree of conversion were estimated by model-free Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose, Tang and Starink methods. The obtained values of E _a were quite close for all of these methods. The reaction models of the phase transitions were derived with using of the model-fitting Coats–Redfern method. In order to find pre-exponential factor A at progressive conversion values, we used values of E _a already estimated by the model-free isoconversional method. It was established that the crystallization processes in thin films investigated are most likely describes by the second and third-order reactions models. Obtained kinetic triplet allowed predicting transition and storage times of the PCM cells. It was found that thin films of Ge₂Sb₂Te₅ + 0.5 mass% Bi composition can provide the switching time of the phase change memory cell less than 1 ns. At the same time, at room temperature this material has a maximum storage time among the studied compositions.     

Influence of chemical nature of aerosilogel surface on proton conductivity of the Nafion-containing composites

Aerosilogel modified with hydroxylaluminum (=Al-OH) groups has been synthesized via the molecular layering procedure, and aerosilogel modified with aminopropylsilyl groups [≡Si(CH₂)₃NH₂] has been prepared via chemisorption of (3-aminopropyl)triethoxysilane. The modified aerosilogel have been further used to prepare composite Nafion-containing electrolytes Nafion. Electrical conductivity of the produced materials has been studied by impedance spectroscopy. Chemical modification of the gel surface strongly affects proton conductivity of Nafion-containing composites.     

Optical Gas Sensing Properties of Silica Film Doped with Cobalt Oxide Nanocrystals

SiO₂ sol-gel films doped with cobalt oxide nanocrystals have been fabricated. The nanocrystals precipitate in the glass film at 500_°C, while the film is still porous. The nanocomposite films showed a reversible change in the optical transmittance when exposed to CO in the 250 < < 850 nm range. The effects of the residual porosity and testing temperature have been studied. The gas sensing properties of the cobalt oxide nanocrystals doped films are compared with those of nickel oxide nanocrystals doped silica film, previously reported.     

Effect of BiFeO3 doping on ferroelectric properties of Na0.5Bi0.5TiO3–BaTiO3 based thin film derived by sol–gel method

0.94Na_0.5Bi_0.5TiO₃–0.06BaTiO₃ (NBT–6BT) and (0.94 ? x)Na_0.5Bi_0.5TiO₃–0.06BaTiO₃–xBiFeO₃ (NBT–6BT–xBFO, x = 0.03, 0.05 and 0.08) thin films were deposited on Pt/Ti/SiO₂/Si substrates by a sol–gel process. Relative permittivity and remnant polarization were maximized at 5 % BFO substitution. Compared with 0.94NBT–0.06BT, the leakage current density of 0.89NBT–0.06BT–0.05BFO at 600 kV/cm is reduced by one order of magnitude. Enhanced ferroelectricity was also achieved in 0.89NBT–0.06BT–0.05BFO, the remnant polarization (2P _r) values of 0.89NBT–0.06BT–0.05BFO and 0.94NBT–0.06BT are 46 and 24 µC/cm².     

Sorption of Ponceau 4R anionic dye from aqueous solutions on aluminum oxide and polyurethane foam

The sorption of Ponceau 4R (E-124) anionic dye on polyurethane foam based on ethers and γ-Al₂O₃ from aqueous solutions is studied. It is established that sorption is highest in the range of 0.5 M HCl, pH 2 on polyurethane foam and 0.2 M HCl, pH 6.5 on γ-Al₂O₃. Under optimum conditions, the degrees of recovery on polyurethane foam and γ-Al₂O₃ are 20–30 and 70–85%, respectively. A possible scheme of interactions between the dye and the surfaces of sorbents is proposed.     

Electrolytic synthesis of FeS2 for thin-layer lithium battery

Purposeful synthesis of iron sulfide FeS₂ films for a lithium battery were purposefully synthesized on a 18N12Kh9T steel cathode from a solution containing Mohr’s salt and Na₂S₂O₃. Various aspects of synthesis were studied. Thin-film Fe-sulfide synthesis products were tested in a prototype lithium battery and also in a lithium-ion system. The synthesized electrolytic iron sulfide FeS₂ with a marcasite structure is capable of reversible electrochemical transformation with output of 390 mA h g^?1 in negative electrodes of the lithium-ion system with a LiMn₂O₄ counter electrode.     

Dielectric properties of Al–Si composite oxide films formed on electropolished and DC-etched aluminum by electrophoretic sol-gel coating and anodizing

Highly pure aluminum specimens (99.99%) after electropolishing and DC-etching were covered with SiO₂ films by electrophoretic sol-gel coating and were anodized in neutral boric acid/borate solutions. Time-variations in cell voltage during electrophoretic sol-gel coating and in anode potential during anodizing were monitored. Structure and dielectric properties of the anodic oxide films were examined by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray (EDX), and electrochemical impedance spectroscopy (EIS). It was found that electrophoretic sol-gel coating forms uniform SiO₂ films on the surface of both electropolished and DC-etched specimens. Anodizing of specimens after electrophoretic coating lead to the formation of anodic oxide films consisting of two layers: an inner alumina layer and an outer Al–Si composite oxide layer. The anodic oxide films formed, thus, had slightly higher capacitances than those formed on aluminum without any coating. Higher heating temperatures after electrophoretic deposition caused the increase in capacitance of anodic oxide films more effectively. Anodizing in a boric acid solution after SiO₂ coating on DC-etched foil allowed the anode potential to reach a value higher than 1,000 V, resulting in 39% higher capacitances than those on specimens without SiO₂ film. Dedicated to Professor Su-Il Pyun on the occasion of his 65th birthday.     

Enhanced ferroelectric,dielectric and leakage properties in Ce and Ti co-doping BiFeO3 thin films

Pure BiFeO₃ (BFO), Ce and Ti individual doping and co-doping BiFeO₃ thin films were fabricated via sol–gel process on Pt/Ti/SiO₂/Si substrates. The microstructure, surface morphology, ferroelectric and dielectric properties of BFO and doped thin films were investigated in detail. X-ray diffraction reveal that all thin films are confirmed the formation of the distorted rhombohedral perovskite structure. No impure phase is identified in all the films. The Ce and Ti co-doping BiFeO₃ (BCFTO) thin films exhibited the enhanced ferroelectricity with a large remnant polarization (2P _r) of 130 μC/cm², and low leakage current density of 9.10 × 10^?6 A/cm² which is more than two orders of magnitude lower than that of pure BFO films at 100 kV/cm. The dielectric constant (364 at 1 kHz) of the BCFTO thin films is much larger than that of pure BFO thin films. These results suggest that the introductions of Ce and Ti provides an effective route for improving the ferroelectric, dielectric and leakage properties of BFO thin films.     

Preparation of polymeric modifier-attached graphene-supported bimetallic Pt–Pd nanocomposites,and their electrochemical properties as electro-catalysts

Graphene-supported bimetallic nanocomposites were synthesized by a modified sodium borohydride reduction method. Poly(diallyldimethylammonium chloride) (PDDA) was used as modifier for good dispersion and higher metal alloy content. The micro-structure and dispersive properties of the electro-catalysts were determined by X-ray diffraction, Fourier-transform-infrared spectroscopy, scanning electron microscopy, and transmission electron microscopy. The electrochemical properties of the Pt–Pd electro-catalysts were studied by cyclic voltammetry. This analysis confirmed that functional groups on the graphene oxide (GO) sheet were chemically bonded to the PDDA layer. The average particle diameter of Pt–Pd_{1 to 0.5}–PDDA–reduced graphene oxide (RGO) was found to be 2.4 ± 0.4 nm which is the smallest platinum metal particle size among Pt–Pd–PDDA–RGO electro-catalysts. The electrochemically active surface area was studied and the activity was found to be enhanced by use of the polymeric modifier.