Effect of block length on the self-assembly of end-capping perfluoroalkyl moieties on the polymer surface

Most research on copolymers with fluorinated monomers has focused on the relationship between fluorinated monomer content and the corresponding surface structure. However, the influence of the non-fluorinated block on the surface structure of the copolymer film is unknown. Various molecular weight poly(butyl methacrylates) (PBMA) end-capped with 2-perfluorooctylethyl methacrylate (FMA) units (PBMA-ec-FMA) have been synthesized by atom transfer radical polymerization (ATRP). The effect of the PBMA block length on the surface structure and properties of the polymers both in the solid state and in solution was investigated using various techniques. X-ray photoelectron spectroscopy (XPS), sum frequency generation (SFG) vibrational spectroscopy and X-ray diffraction (XRD) analyses indicated that longer PBMA blocks enhanced both the enrichment of the fluorinated moieties and the order of the packing orientation of the perfluoroalkyl side chains on the surface. This enhancement was attributed mainly to the molecular aggregate structure of the end-capped polymers with long PBMA blocks in the solution and to the interfacial structure at the air/liquid interface, which favors the -(CF₂)₇CF₃ moieties self-assembling on the polymer surface during film formation. This observation suggests that the polyacrylate block structure in fluorinated diblock copolymers, in addition to the fluorinated monomer content, plays an important role in structure formation on the solid surface.     

Effect of sequence structure on wetting behaviors of fluorinated methacrylate polymers based on perfluorohexylethyl methacrylate and stearyl acrylate

Due to the non-crystalline properties of short chain perfluoroalkyl groups,using short chain perfluoroalkyl to stabilize low surface free energy polymers has been a challenging task.In this study,we prepare a series of random copolymers poly(perfluorohexylethyl methacrylate)-co-poly(stearyl acrylate) (P13FMA-co-PSA) and block copolymers poly(perfluorohexylethyl methacrylate)-b-poly(stearyl acrylate) (P13FMA-b-PSA),and systematically investigate the effects of the sequence structure and the content of 13FMA of the fluorinated copolymers on surface free energy and surface reorganization.Static/dynamic contact angle goniometry and water/oil repellency analyses demonstrate that the random polymer P13FMA-co-PSA could not achieve low surface free energy and low surface reorganization at the same time.In contrast,for the block copolymer P13FMA-b-PSA,both low surface free energy and low surface reorganization are acquired simultaneously.The results of X-ray photoelectron spectroscopy (XPS),dynamic contact angle goniometry and differential scanning calorimetry (DSC) reveal the above-mentioned properties.The consecutive 13FMA segments improve the surface fluorine density,while the consecutive SA chains enhance the crystallinity of the SA segments,and further hinder the surface reorganization of the perfluoroalkyl groups.Therefore,P13FMA-b-PSA exhibits a higher utilization efficiency of fluorine atoms and a better structural stability than P13FMA-co-PSA.     

Solvent effect on the film formation and the stability of the surface properties of poly(methyl methacrylate) end-capped with fluorinated units

The surface structure and stability (the resistance to surface reconstruction) of end-capped poly(methyl methacrylate) films were greatly affected by the solvents used for film preparation. Films of end-capped PMMA with about four 2-perfluorooctylethyl methacrylate units cast with benzotrifluoride solution exhibited excellent stability and resistance to polar environments compared with those cast with cyclohexanone and toluene solutions. The observed difference in stability between these fluorinated surfaces is attributed to their surface microstructures formed during the film formation processes, which are closely related to the associative behavior of the end-capped PMMA in the solution. A relatively perfect close-packed and well-ordered structure of the perfluoroalkyl side chains at the surface of the PMMA(857)-ec-FMA(3.3) film was formed when the film was cast with benzotrifluoride solution, in which only unimers existed. This study indicates that such a solvent effect may be used to promote the formation of a well-ordered packing structure of the fluorinated moieties at the film surface. The ordering of the packing structure is to a certain extent more important than the content of the fluorinated moieties at the surface for improving the surface stability.     

Surface complexation modeling of Fe(3)O(4)-H(+) and Mg(II) sorption onto maghemite and magnetite

New fluorinated copolymers of poly(methyl methacrylate)-b-poly(butyl methacrylate) or poly(n-octadecyl methacrylate) end-capped with 2-perfluorooctylethyl methacrylate (PMMA(x)-b-PBMA(y)-ec-PFMA(z) or PMMA(x)-b-PODMA(y)-ec-PFMA(z)) were synthesized by living atom transfer radical polymerization. Thin films made of PMMA(230)-b-PODMA(y)-ec-PFMA(1) were characterized by differential scanning calorimetry, angle-resolved X-ray photoelectron spectroscopy and X-ray diffraction. These films were found to exhibit robust surface segregation of the end groups. Furthermore, the fluorine enrichment factor at the film surface was found to increase linearly with increasing degree of polymerization of poly(n-octadecyl methacrylate) and its increasing fusion enthalpy in the second block, which enhances the segregation of the fluorinated moieties.     

B段选择性成膜溶剂对 ABC 型氟化三嵌段共聚物氟化组分表面富集行为的影响

利用ATRP技术合成聚甲基丙烯酸甲酯-b-聚甲基丙烯酸丁酯(或聚甲基丙烯酸十八烷基酯)-b-聚(甲基丙烯酸2-全氟辛基乙酯)(PMMA230-b-PBMA12(或PODMA12)-b-PFMAn)嵌段共聚物.通过X射线光电子能谱(XPS)、X射线衍射(XRD)、动态光散射(DLS)等技术研究了中间段选择性成膜溶剂对氟化...     

Preparation of magnetic nanoparticles by the use of self-assembled fluorinated oligomeric aggregates—A new approach to the dispersion of magnetic particles on poly(methyl methacrylate) film surface

Fluoroalkyl end-capped acrylic acid oligomer-encapsulated magnetic nanoparticles were prepared by the coprecipitation of aqueous ferric and ferrous ions in the presence of the corresponding oligomers under alkaline conditions. The dynamic light scattering measurements showed that these fluorinated oligomer magnetic nanoparticles were encapsulated in the self-assemblies of fluoroalkyl end-capped oligomers. Fluoroalkyl end-capped oligomer-encapsulated magnetic nanoparticles thus obtained were applied to the dispersion of magnetic particles on the poly(methyl methacrylate) film surface to exhibit not only the surface active property imparted by fluorine but also magnetic behavior toward a permanent magnet.     

成膜溶剂与氟化嵌段共聚物膜的表面富集行为

利用接触角、XPS、SFG、AFM等技术研究了环己酮、甲苯和三氟甲苯为成膜溶剂所得聚甲基丙烯酸甲酯-b-聚（甲基丙烯酸-2-全氟辛基乙酯）（PMMA—b—PFMA）嵌段共聚物膜的表面结构与性能．发现浇铸成膜时成膜溶剂对聚合物氟化组分向表面富集程度的影响相对较小,而旋涂成膜时溶剂的影响很大．不管以何种形式成膜,三氟甲苯溶剂最有利于氟化组分向表面富集,甲苯次之,环己酮最差．这一现象与溶剂的挥发速度无关．聚合物在溶液中的聚集结构、气／液界面结构是造成成膜方式对聚合物表面结构与性能产生巨大影响的主要原因．当聚合物在溶液中形成以PFMA为核、PMMA为冠的胶束结构时,在溶液固化过程中氟化组分向表面富集需要较长的时间,这时由于成膜方法直接影响溶液的固化速度,造成其对氟化组分向表面富集的程度影响很大．当聚合物在溶液中以单分子或松散聚集体存在,在溶液固化过程中氟化组分向表面富集的速度很快,这时成膜方法对氟化组分向表面富集的程度影响很小．以上结果无论对理论研究还是应用研究都具有重要意义．     

Synthesis and properties of fluorene‐based fluorinated polymers

Fluorene‐based polymers containing various fluorinated benzene (fluorobenzene, p‐difluorobenzene, and tetrafluorobenzene) moieties were synthesized. In addition, perfluorooctylation of poly‐[(9,9‐dioctylfluorene‐2,7‐diyl)‐co‐(fluorene‐2,7‐diyl)] was carried out to afford fluorene‐based polymers with perfluorooctyl moiety at the 9‐position on the fluorene ring. To evaluate the effect of fluorine moiety, polymers containing nonfluorinated benzene moieties and nonfluorinated octyl groups were synthesized. The photoluminescence measurements indicated that all these polymers exhibited blue emission in solution, but a polymer containing a perfluorooctyl group did not emit in the film state. Polymers containing various fluorinated benzene moieties showed higher fluorescence quantum yields and thermal stability than those containing nonfluorinated benzene. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3143–3150, 2001     

Well‐defined poly[(dimethylamimo)ethyl methacrylate]‐b‐poly(fluoroalkyl methacrylate) diblock copolymers: Effects of different fluoroalkyl groups on the solution properties

A series of well‐defined, fluorinated diblock copolymers, poly[2‐(dimethylamino)ethyl methacrylate]‐b‐poly(2,2,2‐trifluoroethyl methacrylate) (PDMA‐b‐PTFMA), poly[2‐(dimethylamino)ethyl methacrylate]‐b‐poly(2,2,3,4,4,4‐hexafluorobutyl methacrylate) (PDMA‐b‐PHFMA), and poly[2‐(dimethylamino)ethyl methacrylate]‐b‐poly(2,2,3,3,4,4,5,5‐octafluoropentyl methacrylate) (PDMA‐b‐POFMA), have been synthesized successfully via oxyanion‐initiated polymerization. Potassium benzyl alcoholate (BzO^?K⁺) was used to initiate DMA monomer to yield the first block PDMA. If not quenched, the first living chain could be subsequently used to initiate a feed F‐monomer (such as TFMA, HFMA, or OFMA) to produce diblock copolymers containing different poly(fluoroalkyl methacrylate) moieties. The composition and chemical structure of these fluorinated copolymers were confirmed by ¹H NMR, ¹⁹F NMR spectroscopy, and gel permeation chromatography (GPC) techniques. The solution behaviors of these copolymers containing (tri‐, hexa‐, or octa‐ F‐atom)FMA were investigated by the measurements of surface tension, dynamic light scattering (DLS), and UV spectrophotometer. The results indicate that these fluorinated copolymers possess relatively high surface activity, especially at neutral media. Moreover, the DLS and UV measurements showed that these fluorinated diblock copolymers possess distinct pH/temperature‐responsive properties, depending not only on the PDMA segment but also on the fluoroalkyl structure of the FMA units. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2702–2712, 2009     

Limited Fraction of Crystallized Side Chains in Bottlebrush Poly(n-alkyl methacrylate)s

Crystallinity of bottlebrush polymers due to side chain crystallization has been considered to be related to the length of the side chains only under the assumption of complete participation of crystallization by all side chains.Recent experimental results revealed that in poly(n-alkyl methacrylate)s a fraction of side chains could not crystallize due to constraints imposed by the trapped main chain entanglements and required expansion of main chain-main chain distance.This result renders the original simplified consideration of the origin of crystallinity in bottlebrush polymers questionable.In this work,we introduce a new parameter fc,the fraction of crystallizable side chains,to better describe the crystallinity of bottlebrush polymers.A linear relationship between the melting enthalpy and the number of alkyl groups in side chains for bottlebrush polymers reported repeatedly indicates that fc remains essentially unchanged when bottlebrush polymers had the same main chain structure and grafting degree but different side chain lengths.The slope of the above-mentioned linear relationship is thus AHCH2×fc,where AHCH2 stands for the melting enthalpy of one mole alkyl group packed into the crystal.With a known value of fc,it is possible to estimate the value of AHCH2.In case of poly(n-alkyl methacrylate)s,we estimated AHCH2 of hexagonal crystal being at most 5.74 kJ/mol with the knowledge of possibly smallest fc of 0.67 obtained from small angle X-ray scattering data.Therefore,the crystallinity of bottlebrush polymer would be calculated based on the equation Xc = fc×Nc/N with N and Nc being the number of alkyl groups in a side chain and those packed in the crystalline structure,respectively.Both chemical structure and grafting degree of bottlebrush polymers affect fc.     

Preparation and applications of novel fluoroalkyl end-capped oligomers/calcium carbonate nanocomposites

Calcium chloride reacted with sodium carbonate in the presence of a variety of self-assembled molecular aggregates formed by fluoroalkyl end-capped acrylic acid, 2-methacryloyloxyethane sulfonic acid, dimethylacrylamide, and acryloylmorpholine oligomers in aqueous solutions to afford the corresponding fluorinated oligomers/calcium carbonate composites in excellent to moderate isolated yields. These fluorinated calcium carbonate composites thus obtained were shown to have a good dispersibility not only in water but also in traditional organic media including fluorinated solvents. Dynamic light scattering measurements (DLS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) showed that these fluorinated composites are nanometer-size-controlled particles and well dispersed in these media. Cross-linked fluoroalkyl end-capped acrylic acid co-oligomer containing poly(oxyethylene) units was also applied to the preparation of new cross-linked fluorinated calcium carbonate nanocomposites under similar conditions. The obtained cross-linked fluorinated calcium carbonate nanocomposites were found to have an extremely higher dispersibility in aqueous and organic media including fluorinated solvents, compared to that of the corresponding fluoroalkyl end-capped oligomer nanocomposites. In particular, it was verified that these fluorinated calcium carbonate nanocomposites are applicable to the dispersion above poly(methyl methacrylate) (PMMA) film surface. Interestingly, field-emission SEM (FE-SEM) images of the cross-section of the modified PMMA films showed that calcium carbonate particles dispersed into these PMMA films could be arranged regularly above the modified film surface. More interestingly, cross-linked fluorinated oligomeric aggregates were able to provide suitable host moieties for the crystallization of calcium carbonate.     

氟化单元封端的不同聚合度PBMA甲苯溶液气/液界面结构

采用ATRP技术合成具有不同聚合度的末端连接甲基丙烯酸全氟辛基乙酯(FMA)单元的聚甲基丙烯酸丁酯(PBMAm-ec-PFMAn).利用和频振动光谱(SFG)和表面张力测定技术研究了各种氟化聚合物溶液的气/液界面结构.发现PBMAm-ec-PFMAn甲苯溶液的表面活性及其气/液界面的结构与两种结构单元数密切相关.当PFMA聚合度(n)大约为4和6时,聚合物溶液的表面张力随着PBMA聚合度的增加从21增加到25mN/m(该值与PBMA均聚物溶液相同).SFG的研究结果表明PBMA段较长时溶液表面被PBMA所占据.PBMA段较短时,PFMA组分吸附在溶液表面,排列比较有序且紧密堆积.当PBMA末端只有1个FMA单元时,其甲苯溶液的表面张力随PBMA段长稍有增加(从22增加到23mN/m),其值介于21与25mN/m之间.研究表明当PBMA段较短时,可能聚合物中的氟化组分吸附在溶液表面,但其排列的有序性较差.随着PBMA聚合度的增加,氟化组分与PBMA组分可能同时占据在溶液表面,这时其表面张力大约为23mN/m.     

Dispersion of gold nanoparticles above the poly(methyl methacrylate) surface by the use of fluoroalkyl end-capped oligomeric aggregates

Nanometer size-controlled gold particles were prepared under mild conditions by reducing the corresponding metal precursor in the presence of self-assembled molecular aggregates formed by fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomers. The stable gold nanoparticles protected by these fluorinated molecular aggregates were applied to the dispersion above the poly(methyl methacrylate) film surface.     

Thermoresponsive characteristics of fluoroalkyl end-capped co-oligomers in aqueous solutions and on the poly(methyl methacrylate) film surface

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide--acryloylmorpholine co-oligomers were prepared by the co-oligomerizations of fluoroalkanoyl peroxides with the corresponding monomers. These fluorinated co-oligomers exhibited a lower critical solution temperature (LCST) characteristic in aqueous solutions. Of particular interest, a steep time dependence of contact angle values for dodecane was observed from 40 to 60 degrees C to decrease their values, effectively, on the modified PMMA [poly(methyl methacrylate)] film surface treated with fluorinated co-oligomer possessing the LCST: 36 degrees C (in water), although such a steep time dependence was not observed from 20 to 30 degrees C.     

Fluorinated star‐shaped block copolymers: Synthesis and optical properties

Tetrakis(4‐(1‐bromoethyl)phenyl)silane is synthesized and utilized to initiate the atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) to generate bromo‐terminated four‐armed PMMA macroinitiators, which further initiate the ATRP of methylacryloyloxyl‐2‐hydroxypropyl perfluorooctanoate (FGOA) to create fluorinated star‐shaped block copolymers PMMA‐b‐poly(FGOA)s with fluorine content ranging from 0 to 31.7 wt %. The polymerizations are well controlled with the polydispersity indices <1.30. The polymers readily dissolve in common organic solvents and show good film‐formation. Compared with the nonfluorinated sample, the fluorinated films exhibit significantly increased water contact angles owing to the enrichment of fluorine on the surface. The enhanced hydrophobicity is advantageous for the optical stability when the devices work under a moist environment. Moreover, the films possess high thermo‐optic coefficients, tunable refractive indices, and extremely low birefringence coefficients because of the presence of bulky and rigid tetraphenylsilane core and star‐shaped topological structure, showing potential application in optical waveguide devices. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1969–1977     

Synthesis of fluorine‐containing star‐shaped poly(vinyl ether)s via arm‐linking reactions in living cationic polymerization

Various types of fluorine‐containing star‐shaped poly(vinyl ether)s were successfully synthesized by crosslinking reactions of living polymers based on living cationic polymerization. Star polymers with fluorinated arm chains were prepared by the reaction between a divinyl ether and living poly(vinyl ether)s with fluorine groups (C₄F₉, C₆F₁₃, and C₈F₁₇) at the side chain using cationogen/Et_1.5AlCl_1.5 in a fluorinated solvent (dichloropentafluoropropanes), giving star‐shaped fluorinated polymers in high yields with a relatively narrow molecular weight distribution. The concentration of living polymers for the crosslinking reaction and the molar feed ratio of a bifunctional vinyl ether to living polymers affected the yield and molecular weight of the star polymers. Star polymers with block arms were prepared by a linking reaction of living block copolymers of a fluorinated segment and a nonfluorinated segment. Heteroarm star‐shaped polymers containing two‐ or three‐arm species were synthesized using a mixture of different living polymer species for the reaction with a bifunctional vinyl ether. The obtained polymers underwent temperature‐induced solubility transitions in various organic solvents, and their concentrated solutions underwent sol–gel transitions, based on the solubility transition of a thermoresponsive fluorinated segment. Furthermore, a slight amount of fluorine groups were shown to be effective for physical gelation when those were located at the arm ends of a star polymer. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparation of fluoroalkyl end-capped oligomers/magnetite nanocomposites possessing a good dispersibility and stability

Fluoroalkyl end-capped vinylphosphonic acid cooligomers-encapsulated magnetite nanocomposites were prepared by the magnetization of aqueous ferric and ferrous ions in the presence of the corresponding fluorinated cooligomers and magnetic nanoparticles under alkaline conditions. These fluorinated cooligomers magnetic composites are nanometer size-controlled very fine particles and have a good dispersibility and stability in water and traditional organic solvents. These fluorinated nanocomposites were also applied to the surface modification of poly(methyl methacrylate) to exhibit a good oleophobicity imparted by fluorine on their surface. Fluoroalkyl end-capped 2-methacryloyloxyethanesulfonic acid oligomer-encapsulated magnetite nanocomposites and fluoroalkyl end-capped 2-acrylamide-2-methylpropanesulfonic acid oligomer-encapsulated magnetite nanocomposites were prepared in good isolated yields by the magnetization of iron chlorides in the presence of the corresponding oligomers and magnetic nanoparticles under similar conditions. Colloidal stability of these fluorinated nanocomposites thus obtained in water was demonstrated to become extremely higher than that of fluorinated vinylphosphonic acid cooligomers/magnetic nanocomposites.     

Arrangement of fullerene above the poly(methyl methacrylate) surface with fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide polymers

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide polymers were found to be a convenient tool for the arrangements of fullerenes above the poly(methyl methacrylate) [PMMA] surface, and the higher fluorescent intensity of fullerene was obtained in the modified PMMA surface, although the reverse side of this modified film surface afforded an extremely weak fluorescent intensity.     

Surface active semifluorinated diblock copolymers prepared by group transfer polymerization

Diblock copolymers consisting of poly(methyl methacrylate) and poly(2-perfluorobutylethyl methacrylate) with narrow molecular weight distribution have been synthesized by group transfer polymerization. Different ratios of the PMMA block to the fluorinated block have been prepared. It was found that all polymers are surface active. Critical micelle concentrations are not dependent on the fluorinated block length. Critical surface tensions, extrapolated from Zisman plots and the dispersion force component of the surface energies extrapolated from Girifalco-Good-Fowkes-Young plots were decreasing with increasing length of the fluorinated block.     

UV-curable low-surface-energy fluorinated poly(urethane-acrylate)s for biomedical applications

Novel UV-curable fluorinated poly(urethane-acrylate) (FPUA) oligomers have been synthesized from 1H,1H,12H,12H-perfluoro-1,12-dodecanediol (PFDDOL), either 1,6-hexamethylene diisocyanate (HDI) or 4,4′-diphenylmethane diisocyanate (MDI), and 2-hydroxyethyl methacrylate (HEMA) for end-capping with photo-crosslinkable methacrylate groups. The fluorine content and the nature of the isocyanate were investigated to determine their effects on the physical properties, surface properties, and blood compatibilities of the polymers. The introduction of hydrophobic fluorocarbon chains led to phase separation and a low total surface energy, which reduced the adhesion of blood platelets onto the materials. The HDI-type UV-curable, fluorinated poly(urethane-acrylate) exhibited a low-surface-energy and superior blood compatibility (as determined from RIPA values).