Hydrogen chromate PVC matrix membrane sensor for potentiometric determination of chromium(III) and chromium(VI) ions

A novel potentiometric Cr(6+) PVC matrix membrane sensor incorporating nickel tris(1,10-bathophenanthroline) hydrogen chromate as an electroactive material and 2-nitrophenyl phenyl ether as solvent mediator is described. In a phosphate buffer solution of pH 5, the sensor displays a rapid and linear response for Cr(6-) over the concentration range 2 x 10(-2)-8 x 10(-6) M with an anionic slope of 55.5 +/- 0.2 mV decade(-1) and a detection limit of the order of 0.4 microg ml(-1). The sensor is used for sequential determination of Cr(6+) and Cr(3+) by direct monitoring of Cr(6+) followed by oxidation of Cr(3+) and measurement of the total chromium. The average recoveries of Cr(3+) and Cr(6+) at concentration levels of 0.5-50 microg ml(-1) are 98.1 +/- 0.4% and 99.1 +/- 0.4% respectively. Redox and precipitation titrations involving Cr(6+) as a titrant are monitored with the sensor. Cr(3+) and/or Cr(6+) in wastewaters of some industries (e.g., leather tanning, electroplating, aluminum painting) and the chromium contents of some alloys and refractory bricks are assessed. The results agree fairly well with data obtained using the standard diphenylcarbazide spectrophotometric method.     

Membrane sensors for batch and flow injection potentiometric determination of ethamsylate (cyclonamine) in pharmaceutical preparations

The lipophilic nickel(II) and iron(II) bathophenanthroline derivatives of ethamsylate are used as ion-exchangers with high selectivity characteristics for ethamsylate. Poly(vinyl chloride) membrane sensors incorporating these electroactive materials display fast linear response for 1 × 10^–1–1 × 10^–4 M ethamsylate under static and hydrodynamic modes of operation. In an acetate buffer of pH 4, the calibration slope is 51–53 mV/concentration decade and the lower limit of detection is 5.3 g/ml. Except for salicylate and nitrate, most common anions, organic sulfonates, carboxylates, phenolates and various pharmaceutical excipients and diluents do not interfere. Determination of ethamsylate in various dosage forms shows an average recovery of 98.9% of the nominal and a mean standard deviation of 0.7%.     

Screen-printed multienzyme arrays for use in amperometric batch and flow systems

Screen-printing technology for electrode fabrication enables construction of amperometric devices suitable for combination of several enzyme electrodes. To develop a biosensor array for characterisation of wastewaters, tyrosinase and horseradish peroxidase (HRP) or cholinesterase-modified electrodes were combined on the same array. The behaviour of the tyrosinase-modified electrode in the presence of hydrogen peroxide (required co-substrate for the HRP-modified electrode) and acetylthiocholine chloride (required co-substrate for cholinesterase) was studied. Performance of bi-enzyme biosensor arrays in the batch mode and in the flow-injection system are discussed.     

Screen-printed reference electrodes for potentiometric measurements

A convenient and reliable method for large-scale production of miniaturized, planar, all-solid-state reference electrodes is reported. All elements of the Ag/AgCl/KCl reference half-cell i.e. layer of Ag/AgCl (inner electrode), immobilized electrolyte (junction) and encapsulation are fabricated by means of screen-printing technology. The use of pastes cured in low temperature allows fabrication on low-cost, plastic, flexible foils. The developed reference electrodes exhibit good long-term stability. Continuous operation life-time exceeds one week. Storage stability is longer than 9 months. pH, chlorides as well as other halide anions, typical buffer components, alkaline and heavy metal cations, complexing ligands and redox agents, do not influence the potential of the reference electrodes. The developed reference electrodes are compatible with strip potentiometric sensors fabricated in the same format. Examples of analytical applications of the reference electrodes with various screen-printed sensors are demonstrated.     

Simultaneous determination of chromium(VI) and chromium(III) by flame atomic absorption spectrometry with a chelating ion-exchange flow injection system

Summary Simultaneous Determination of Chromium(VI) and Chromium(III) by Flame Atomic Absorption Spectrometry with a Chelating Ion-Exchange Flow Injection System A simple method is described for the simultaneous determination of chromium(VI) and chromium(III) in a flow injection system comprising chelating ion-exchange and flame atomic absorption spectrometry. Sampling rates for 2001 and 1 ml sample volumes were 120 and 60 h^–1 (240 and 120 speciations per hour), respectively. Typical relative standard deviations were 0.52% for Cr(VI) (0.50g ml^–1 and 0.67% for Cr(III) (0.10,g ml^–1) and the corresponding limits of detection were 85 ng ml^–1, and 16 ng ml^–1, respectively.On leave from University of Belgrade.     

Method for the determination of chromium (VI) as chromium (VI)-dibenzyidithiocarbamate

Dibenzyldithiocarbamic acid (DBDC) exhibits the ability to speciate between chromium(VI) and chromium(III), since only the chromium(VI) will form complexes with DBDC. The complex is then extracted into an organic solvent and assayed using an ultraviolet-visible (UV-VIS) spectrophotometer at 498.8 nm. Using 250 ml of aqueous sample detection limits less than 1 ng/ml are possible, while the linear range extends to 500 gmg/ml when working at 498.8 nm. Oxidation of the chromium(III) to chromium (VI) using cerium (IV) enables the determination of total chromium and subsequently the chromium (III) in solution. Evaluation of the method with a standard reference material produced only 4.81 part per thousand error in the determination of chromium(VI).     

Determination of trace amounts of chromium (VI) by flow injection analysis with chemiluminescence detection

A new sensitive chemiluminescence (CL) method combined with continuous flow injection analysis is described for the determination of Cr(VI). Strong CL signals were generated by Cr(VI)-catalysed oxidation of gallic acid in the presence of potassium permanganate and hydrogen peroxide. Effects of reagent concentrations, temperature, pH, flow rates, mixing coil length and mixing flow sequences on the chemiluminescence intensity were studied. Under the optimised experimental conditions, the relationship between the logarithm of concentration (log?C) of Cr(VI) and the logarithm of intensity (log?I) is linear over the range of 2?×?10^?11 – 5?×?10^?4?mol?L^?1, with the detection limit (3σ) of 4?×?10^?12?mol?L^?1. Relative standard deviation of ten measurements of 1?×?10^?9?mol?L^?1 Cr(VI) is 1.7%. This flow injection analysis (FIA) system proved to be able to analyse up to 40 samples h^?1. Effects of various interferences possibly present in the water samples were investigated. Most cations and anions, as well as organic compounds, did not interfere with the determination of Cr(VI) in water samples. The experimental results obtained for chromium in reference materials were also in good agreement with the certified values.     

Simultaneous and sequential determination of chromium(VI) and chromium(III) by unsegmented flow methods

Summary Several different configurations for simultaneous and sequential photometric speciation of Cr(VI) and Cr(III) based on the reversed flow injection analysis and completely continuous modes are proposed in this paper. The determination of these species at theg · ml^–1 level is achieved with sampling frequencies between 30 and 100 h^–1 and an r.s.d. of less than ±1% for simultaneous methods and of less than ±3% for the sequential method. The proposed methods are suitable for chromium speciation in waters. A simulation of the continuous monitoring of Cr(VI) and periodical of Cr(III) in natural and waste waters has been performed. The most frequent interferents in these types of samples have been investigated.

---

Simultane und sequentielle Bestimmung von Chrom(VI) und Chrom(III) durch unsegmentierte Durchflußmethoden

Zusammenfassung Verschiedene Arten der simultanen und sequentiellen photometrischen Cr(III)- und Cr(VI)-Bestimmung nach der Technik der reversed-flow Injektionsanalyse werden beschrieben. Die relative Standardabweichung für die Bestimmung dieser Chromspezies im g/ml-Bereich bei einer Probenfrequenz von 30 bis 100 je Stunde beträgt weniger als +1% für die Simultan- und weniger als +3% für die sequentiellen Methoden. Eine simulierte kontinuerliche Überwachung von Chrom(VI) sowie eine periodische von Chrom(III) in natürlichem Wasser und Abwasser wird beschrieben. Die häufigsten Störungen werden diskutiert.

     

Flavin mononucleotide chemiluminescence in cationic micellar media for determination of chromium(III + VI) by flow injection

The flavin mononucleotide chemiluminescence system, originally developed for the determination of copper(II), is modified with cationic surfactant micelles for the determination of chromium(III + VI). In order for chromium to be detected predominantly, the copper-induced luminescent reaction is significantly suppressed by virtue of the cationic micellar effect. The limit of detection (signal-to-noise ratio = 2) is 5 × 10^?8 M chromium (50-μl sample injection).     

Ion-selective electrodes for potentiometric determination of ranitidine hydrochloride, applying batch and flow injection analysis techniques.

New ranitidine hydrochloride (RaCl)-selective electrodes of the conventional polymer membrane type are described. They are based on incorporation of ranitidine-tetraphenylborate (Ra-TPB) ion-pair or ranitidine-phosphotungstate (RaPT) ion-associate in a poly(vinyl chloride) (PVC) membrane plasticized with dioctylphthalate (DOP) or dibutylphthalate (DBP). The electrodes are fully characterized in terms of the membrane composition, solution temperature, and pH. The sensors showed fast and stable responses. Nernstian response was found over the concentration range of 2.0 x 10(-5) M to 1.0 x 10(-2) M and 1.0 x 10(-5) M to 1.0 x 10(-2) M in the case of Ra-TPB electrode and over the range of 1.03 x 10(-5) M to 1.00 x 10(-2) M and 1.0 x 10(-5) M to 1.0 x 10(-2) M in the case of Ra-PT electrode for batch and FIA systems, respectively. The electrodes exhibit good selectivity for RaCl with respect to a large number of common ions, sugars, amino acids, and components other than ranitidine hydrochloride of the investigated mixed drugs. The electrodes have been applied to the potentiometric determination of RaCl in pure solutions and in pharmaceutical preparations under batch and flow injection conditions with a lower detection limit of 1.26 x 10(-5) M and 5.62 x 10(-6) M at 25 +/- 1 degrees C. An average recovery of 100.91% and 100.42% with a relative standard deviation of 0.72% and 0.53% has been achieved.     

Screen-printed voltammetric sensor for TNT

Screen-printed carbon electrodes have been developed as disposable voltammetric sensors for 2,4,6-trinitrotoluene (TNT). Thick-film electrodes based on various conventional and modified inks have been compared for this task. The operation is based on placing the selected thick-film carbon sensor in the non-deaerated/quiescent sample and using a fast (<1 s) and sensitive square-wave voltammetric scan. Different experimental variables have been optimized to yield a detection limit of 200 ppb TNT and a wide linear range. The high selectivity, demonstrated in assays of various untreated environmental samples, is attributed to the facts that the reducible nitro group is rare in nature and that most electroactive organic compounds require higher potentials. The new single-use sensor strips should facilitate the on-site environmental screening of TNT.     

Flow and batch systems for copper(II) potentiometric sensing

A new carbon paste electrode modified with tetramethyl thiuram disulfide is prepared to use as copper potentiometric sensor in batch and flow analysis. The influence of pH and carbon paste composition on the potentiometric response is studied. The principal parameters of the flow system are optimized and the detection limits and the selectivity coefficients of the potentiometric sensor are calculated for static and flow mode. In both cases, the sensor shows high selectivity to copper ions but in flow analysis this selectivity is higher. The obtained detection limits are 4.6 × 10⁻⁸ M for batch measurements and 2.0 × 10⁻⁷ M for on-line analysis. The potentiometric sensor is applied to copper(II) determination in real samples in static and flow measurements. In both analysis modes, successful results are obtained.     

Novel potentiometric membrane sensor for the determination of trace amounts of chromium(III) ions.

A plasticized Cr3+ ion sensor by incorporating 2,3,8,9-tetraphenyl-1,4,7,10-tetraazacyclododeca-1,3,7,9-tetraene (TTCT) ionophore exhibits a good potentiometric response for Cr3+ over a wide concentration range (1.0 x 10(-6)-1.0 x 10(-1) M) with a slope of 19.5 mV per decade. The sensor response is stable for at least three months. Good selectivity for Cr3+ in comparison with alkali, alkaline earth, transition and heavy metal ions, and minimal interference are caused by Li+, Na+, K+, Co2+, Hg2+, Ca2+, Pb2+ and Zn2+ ions, which are known to interfere with other chromium membrane sensors. The TTCT-based electrode shows a fast response time (15 s), and can be used in aqueous solutions of pH 3-5.5. The proposed sensor was used for the potentiometric titration of Cr3+ with EDTA and for a direct potentiometric determination of Cr3+ content in environmental samples.     

Flow injection potentiometric sensor for determination of phenylpropanolamine hydrochloride

A new polymeric membrane electrode has been constructed for the determination of phenylpropanolamine hydrochloride. The electrode was prepared by solubilizing the phenylpropanolamine-phosphomolybdate ion associate into a polyvinyl chloride matrix plasticized by dibutylphthalate as a solvent mediator. The electrode showed near-Nernstian response over the concentration range of 1 × 10^?5–1 × 10^?2 M with low detection limit of 6.3 × 10^?6 M. The electrode displays a good selectivity for phenylpropanolamine with respect to a number of common inorganic and organic species. The electrode was successfully applied to the potentiometric determination of phenylpropanolamine ion in its pure state and its pharmaceutical preparation in batch and flow injection conditions.     

Differential determination of chromium(VI) and total chromium in natural waters using flow injection on-line separation and preconcentration electrothermal atomic absorption spectrometry.

A rapid, sensitive and selective method for the differential determination of CrIII and CrVI in natural waters is described. Chromium(vi) can be determined directly by flow injection on-line sorbent extraction preconcentration coupled with electrothermal atomic absorption spectrometry using sodium diethyldithiocarbamate as the complexing agent and C18 bonded silica reversed-phase sorbent as the column material. Total Cr can be determined after oxidation of CrIII to CrVI by potassium peroxydisulfate. Chromium(III) can be calculated by difference. The optimum conditions for sorbent extraction of CrVI and oxidation of CrIII to CrVI are evaluated. A 12-fold enhancement in sensitivity compared with direct introduction of 40 microliters samples was achieved after preconcentration for 60 s, giving detection limits of 16 ng l-1 for CrVI and 18 ng l-1 for total Cr (based on 3 sigma). Results obtained for sea-water and river water reference materials were all within the certified range for total Cr with a precision of better than 10% relative standard deviation in the range 100-200 ng l-1. The selectivity of the determination of CrVI was evaluated by analysing spiked reference materials in the presence of CrIII, resulting in quantitative recovery of CrVI.     

Rapid determination of chromium(VI) in electroplating waste water by use of a spectrophotometric flow injection system

A new rapid and sensitive FI method is reported for spectrophotometric determination of trace chromium(VI) in electroplating waste water. The method is based on the reaction of Cr(VI) with sodium diphenylamine sulfonate (DPH) in acidic medium to form a purple complex (lambda(max) = 550 nm). Under the optimized conditions, the calibration curve is linear in the range 0.04-3.8 microg ml(-1) at a sampling rate of 30 h(-1). The detection limit of the method is 0.0217 microg ml(-1), and the relative standard deviation is 1.1% for eight determinations of 2 microg ml(-1) Cr(VI). The proposed method was applied to the determination of chromium in electroplating waste water with satisfactory results.     

Simultaneous flow injection determination of iron(III) and vanadium(V) and of iron(III) and chromium(VI) based on redox reactions

A flow injection analysis (FIA) method is presented for the simultaneous determinations of iron(III)-vanadium(V) and of iron(III)-chromium(VI) using a single spectrophotometric detector. In the presence of 1,10-phenanthroline (phen), iron(III) is easily reduced by vanadium(IV) to iron(II), followed by the formation of a red iron(II)-phen complex (lambda(max) = 510 nm), which shows a positive FIA peak at 510 nm corresponding to the concentration of iron(III). On the other hand, in the presence of diphosphate the reductions of vanadium(V) and/or chromium(VI) with iron(II) occur easily because the presence of diphosphate causes an increase in the reducing power of iron(II). In this case iron(II) is consumed during the reaction and a negative FIA peak at 510 nm corresponding to the concentration of vanadium(V) and/or chromium(VI) is obtained. The proposed method makes it possible to obtain both positive (for iron(III)) and negative (for vanadium(V) or chromium(VI)) FIA peaks with a single injection.     

Sequential injection wetting film extraction applied to the spectrophotometric determination of chromium(VI) and chromium(III) in water

The spectrophotometric determination of Cr(VI) and Cr(III) via sequential injection was used to demonstrate the sensitivity enhancement provided by a newly developed wetting film extraction system. The reaction product of Cr(VI) with 1,5-diphenylcarbazide was ion-paired with perchlorate and extracted into an organic wetting film consisting of octanol and 4-methyl-2-pentanone on the inner wall of a Teflon tube. The wetting film, with the extracted analyte, was then eluted with 100 mul acetonitrile and the analyte determined spectrophotometrically at 546 nm. Important optimized parameters were the selection of wetting film and elution solvents, the flow rate, the length and diameter of the extraction coil and the conditions for the formation of the ion paired chelate. Cr(III) was previously oxidized to Cr(VI) and calculated as the difference between total Cr and Cr(VI). An enrichment factor of 25 and a detection limit of 2.0 mug l(-1) Cr(VI) were achieved with a sampling frequency of 17 h(-1). The calibration curve was linear up to 100 mug l(-1) Cr(VI) (r = 0.999). The relative standard deviations were 2.8 and 2.0% at the 25 and 100 mug l(-1) levels.     

Flow injection direct spectrophotometric assay for the speciation of trace chromium(III) and chromium(VI) using chromotropic acid as chromogenic reagent

A new rapid and sensitive FI assay is reported for the simultaneous direct spectrophotometric determination of trace Cr(VI) and Cr(III) in real samples. The method is based upon the reaction of Cr(VI) with chromotropic acid (CA) in highly acidic medium to form a water-soluble complex (λ_max = 370 nm). Cr(III) reacts with CA only after its on-line oxidation to Cr(VI) by alkaline KIO₄. The determination of each chromium species in the sample was achieved by absorbance differences. The calibration curves were linear over the range 3-4000 μg l⁻¹ and 30-1200 μg l⁻¹ for Cr(VI) and Cr(III), respectively, while the precision close to the quantitation limit was satisfactory in both cases (s_r = 3.0% for Cr(VI) and 4.0% for Cr(III) (n = 10) at 10 and 50 μg l⁻¹ level, respectively). The method developed proved to be adequately selective and sensitive (c_L = 1 and 10 μg l⁻¹ for Cr(VI) and Cr(III), respectively). The application of the method to the analysis of water samples (tap and mineral water) gave accurate results based on recovery studies (93-106%). Analytical results of real sample analysis were in good agreement with certified values.     

Speciation of chromium (III) and chromium (VI) by capillary electrophoresis with contactless conductometric detection and dual opposite end injection

A sensitive, rapid and inexpensive capillary electrophoretic method for the determination of Cr(III) and Cr(VI) species is presented. The method is based on the dual opposite end injection principle and contactless conductometric detection. The sample containing cationic and anionic species is injected into the opposite ends of the separation capillary and after the high voltage is applied, the analytes migrate towards the capillary center, where the cell of a contactless conductivity detector is placed. The method does not require any sample pretreatment, except dilution with deionized water. The separation of Cr(III), Cr(VI) and other common inorganic anions and cations is achieved in less than 4 min. The parameters of the separation electrolyte solution, such as pH and concentration of L-histidine, were optimized. Best results were achieved with electrolyte solution consisting of 4.5 mM L-histidine, adjusted to pH 3.40 with acetic acid. The detection limits achieved for Cr(III) and Cr(VI) were 10 and 39 microg.L(-1), respectively. The repeatability of migration times and peak areas was better than 0.3% and 2.8%, respectively. The developed method was applied to the analyses of rinse water samples from the galvanic industry. The results for the determination of Cr(III) and Cr(VI) were in good agreement with the results obtained by certified differential spectrophotometric method using diphenylcarbazide (CN 83 0520-40) and with the results for the total chromium concentrations determined by electrothermal atomic absorbance spectrometry (ET-AAS) and inductively coupled plasma-mass spectrometry (ICP-MS).