Absorption of a rigid frame porous layer with periodic circular inclusions backed by a periodic grating

The acoustic properties of a periodic rigid frame porous layer with multiple irregularities in the rigid backing and embedded rigid circular inclusions are investigated theoretically and numerically. The theoretical representation of the sound field in the structure is obtained using a combination of multipole method that accounts for the periodic inclusions and multi-modal method that accounts for the multiple irregularities of the rigid backing. The theoretical model is validated against a finite element method. The predictions show that the acoustic response of this structure exhibits quasi-total, high absorption peaks at low frequencies which are below the frequency of the quarter-wavelength resonance typical for a flat homogeneous porous layer backed by a rigid plate. This result is explained by excitation of additional modes in the porous layer and by a complex interaction between various acoustic modes. These modes relate to the resonances associated with the presence of a profiled rigid backing and rigid inclusions in the porous layer.     

Acoustic radiation force on a rigid cylinder near rigid corner boundaries exerted by a Gaussian beam field

Acoustic manipulation is one of the well-known technologies of particle control and a top research in acoustic field. Calculation of acoustic radiation force on a particle nearby boundaries is one of the critical tasks, as it approximates realistic applications. Nevertheless, it is quite difficult to solve the problem by theoretical method when the boundary conditions are intricate. In this study, we present a finite element method numerical model for the acoustic radiation force exerting on a rigid cylindrical particle immersed in fluid near a rigid corner. The effects of the boundaries on acoustic radiation force of a rigid cylinder are analyzed with particular emphasis on the non-dimensional frequency and the distance from the center of cylinder to each boundary. The results reveal that these parameters play important roles in acoustic manipulation for particle-nearby complicated rigid boundaries. This study verifies the feasibility of numerical analysis on the issue of acoustic radiation force calculation close to complex boundaries, which may provide a new idea on analyzing the acoustic particle manipulation in confined space.     

Point-force excited vibrations of a thin,infinite panel separating a fluid layer from a fluid half-space

A coupled system consisting of a thin, infinite panel separating a fluid layer and a fluid half-space is considered. The response of the panel when driven by a point harmonic force is evaluated by using Hankel transform analysis in conjunction with complex variable integration techniques. The emphasis is placed on frequencies well below the panel critical frequency, on dense fluid loading, and on the condition of shallow layer depth. The analysis yields the free propagation wave numbers of the coupled system: below the critical frequency, all but one are complex. From the solutions of the response integrals, the panel flexural velocity, the acoustic pressures, the power transmitted into the structure and into the fluid layer, and the radiated acoustic power, are obtained.     

The two-mode waveguide formed by a rigid plane and an elastic plate

The structure of the acoustic field formed in the gap between a rigid plane and an elastic plate excited by a point force is considered. Special attention is given to the frequency range near the coincidence frequency in the case of the small values of the load parameter characterizing the plate loading with the medium. Expressions for the energy fluxes in the plate and in the gap are obtained, and the characteristic length of the energy transfer into the gap, as well as the degree of completeness of such a transfer, is determined.     

Analysis of underwater decoupling properties of a locally resonant acoustic metamaterial coating

This paper presents a semi-analytical solution for the vibration and sound radiation of a semi-infinite plate covered by a decoupling layer consisting of locally resonant acoustic metamaterial. Formulations are derived based on a combination use of effective medium theory and the theory of elasticity for the decoupling material. Theoretical results show good agreements between the method developed in this paper and the conventional finite element method(FEM), but the method of this paper is more efficient than FEM. Numerical results also show that system with acoustic metamaterial decoupling layer exhibits significant noise reduction performance at the local resonance frequency of the acoustic metamaterial, and such performance can be ascribed to the vibration suppression of the base plate. It is demonstrated that the effective density of acoustic metamaterial decoupling layer has a great influence on the mechanical impedance of the system. Furthermore, the resonance frequency of locally resonant structure can be effectively predicted by a simple model, and it can be significantly affected by the material properties of the locally resonant structure.     

Study of thermoviscous dissipation on axisymmetric wave propagating in a shear pipeline flow confined by rigid wall. Part II. Numerical study

Axisymmetric acoustic wave propagating in a shear pipeline flow confined by a rigid wall is studied in the two-part paper. The effects of viscous friction and thermal conduction on the acoustic wave propagating in the liquid and perfect gas are respectively analyzed under different configurations of acoustic frequency and shear mean flow. In Part 2 of this paper, comprehensive analysis of the effects of shear mean flow and acoustic frequency on the features (relative phase velocity and attenuation coefficient) of the acoustic wave are numerically addressed in cases of water and perfect gas respectively. Comparisons between the non-isentropic and isentropic models are provided in details. Meanwhile, discussions of the thermoviscous effects on the acoustic wave between water and perfect gas are given.     

水下任意刚性散射体对Bessel波的散射特性分析

本文利用Bessel波的谐波展开式, 采用T矩阵方法的推导思路, 建立了水下任意刚性散射体在Bessel波照射下的声散射场计算公式. 以水下刚性椭球体和两端附连半球的刚性圆柱体为例, 计算了在不同波锥角β 下的反向散射形态函数, 同时, 依据镜反射波和绕行波的干涉物理模型, 给出了预报Bessel波照射下的反向散射形态函数峰峰间隔值的计算模型. 仿真结果表明本文提出的Bessel波照射下反向散射形态函数峰峰间隔值预报方法是准确有效的, 同时也说明, 本文建立的基于T矩阵法计算水下任意刚性散射体在Bessel波束下的声散射场方法是有效的, 这拓展了T矩阵法的应用领域.     

Structural-borne acoustics analysis and multi-objective optimization by using panel acoustic participation and response surface methodology

This paper is aimed to investigate the structural-borne acoustics analysis and multi-objective optimization of an enclosed box structure by using the panel acoustic participation (PAP) and response surface methodology (RSM). The acoustic frequency response function is applied to achieve the critical frequency of interest under each excitation. The PAP analysis is then carried out at all critical frequencies and the remarkable acoustic panels are identified. The correlation coefficient matrix method is proposed for reselecting and grouping the positions of acoustic panels identified to paste damping layer to control noise. With the help of faced central composite design, an efficient set of sample points are generated and then the second-order polynomial functions of sound pressure response at each critical frequency are computed and verified by the adjusted coefficient of multiple determination. The functional relationships between sound pressure responses and the thicknesses of damping layers are investigated, and multi-objective optimization of the thicknesses of damping layers is developed. The results indicate that, by using the PAP and RSM, the structural-borne acoustics at critical frequencies are calculated conveniently and controlled effectively. The optimization process of the explicit optimization model proposed in this paper is simple and the computational time is saved.     

A practical acoustical absorption analysis of coir fiber based on rigid frame modeling

An analytical study based on rigid frame model is demonstrated to evaluate the acoustic absorption of coir fiber. Effects of different conditions such as combination of air gap and perforated plate (PP) are studied in this work. Materials used here are treated as rigid rather than elastic, since the flow resistivity of coir fiber is very low. The well-known rigid frame Johnson-Allard equivalent-fluid model is applied to obtain the acoustic impedance of single layer coir fiber. Atalla and Sgard model is employed to estimate the surface impedance of PP. Acoustic transmission approach (ATA) is utilized for adding various consecutive layers in multilayer structure. Models are examined in different conditions such as single layer coir fiber, coir fiber backed with air gap, single layer PP in combination with coir fiber and air gap. Experiments are conducted in impedance tube on normal incidence sound absorption to validate the results. Results from the measurement are found to be in well agreement with the theoretical absorption coefficients. The performance of the rigid frame modeling method is checked more specifically in all conditions, by the mean prediction error rate of normal incidence sound absorption coefficients. Comparison between the measured absorption coefficients and predicted by rigid frame method shows discrepancy lower than 20 and 15% for most of the conditions in the frequency range of 0.2?C1.5 and 1.5?C5 kHz, respectively. Moreover, acoustic absorption of various single and multilayer structures is compared with the simpler empirical methods such as Delany-Bazley and Miki model; and complicated method such as Biot-Allard Model and Allard Transfer Function (TF) method. Comparisons show that the presented method offers a better accuracy of the results than the empirical models. Subsequently, it can provide almost same absorption plot with Biot-Allard model (single layer combination) and TF method (multilayer combination) proving it to be a comprehensively easy and general analytical tool. Therefore, the rigid frame model can be implemented relatively easier than other similar models to analyze the acoustic absorption of coir fiber in most of the conditions.     

新型掺碳二氧化硅-薄膜体声波谐振器结构及其仿真验证

一定厚度的低声阻抗支撑层可以在薄膜体声波谐振器(FBAR)与衬底之间形成声学隔离层,防止声波泄漏到衬底当中。掺碳二氧化硅(CDO)是一种低声阻抗材料,对FBAR具有较好的温度补偿效果,可以作为FBAR与衬底之间的声学隔离层,从而构成一种新型的CDO-FBAR。为了分析CDO-FBAR与通孔型FBAR相比性能是否退化,以及CDO声学隔离层所需厚度,采用多物理场耦合仿真软件分析了CDO-FBAR和通孔型FBAR的谐振频率、Q值、有效机电耦合系数和S参数,并提取了CDO-FBAR纵向振动位移。分析结果表明:CDO-FBAR的谐振频率整体向下漂移;CDO声学隔离层导致S参数的寄生干扰;由于声学损耗增加,Q值略有降低,其中并联谐振点处的Q值降幅更大;有效机电耦合系数略有降低;声波传播到声学隔离层中9 m处就完全衰减,即只需要9 m厚的CDO声学隔离层就能在FBAR与衬底之间形成有效的声学隔离。由此,仿真验证了这种新颖的CDO-FBAR结构的可行性。     

"Ladder" structure in tonal noise generated by laminar flow around an airfoil

The presence of a "ladder" structure in the airfoil tonal noise was discovered in the 1970s, but its mechanism hitherto remains a subject of continual investigation in the research community. Based on the measured noise results and some numerical analysis presented in this letter, the variations of four types of airfoil tonal noise frequencies with the flow velocity were analyzed individually. The ladder structure is proposed to be caused by the acoustic/hydrodynamic frequency lag between the scattering of the boundary layer instability noise and the discrete noise produced by an aeroacoustic feedback loop.     

Sound propagation around rigid barriers laterally confined by tall buildings

This paper focuses on the propagation of sound waves in the presence of acoustic barriers placed close to very tall buildings. The boundary element method (BEM) is used to model the acoustic barrier, while the presence of the tall buildings is taken into account by using the image source method. Different geometries are analyzed, representing the cases of a single building, two buildings forming a corner and three buildings defining a laterally confined space. The acoustic barrier is assumed to be non-absorbing, and all the buildings and the ground are modeled as infinite rigid plane surfaces. Calculations are performed in the frequency domain and time signals are then obtained by means of Inverse Fourier Transforms. The sound pressure loss provided by the acoustic barrier is computed, illustrating the importance of the lateral confinements.     

Modeling of a high frequency ultrasonic transducer using periodic structures

Solidly mounted integrated transducers with a Bragg cell inserted between the piezoelectric film and the substrate are investigated for high frequency ultrasonic applications. A numerically stable recursive one dimensional transmission/reflection model was used to analyze the behavior of the periodic structure. This theoretical analysis includes the study of the influence of the acoustic properties of the constitutive layer, the effect of the number of cells and their arrangement. A 35 MHz integrated transducer consisting in a PZT ceramic laid down on a Au/PZT Bragg cell deposited on a porous substrate was fabricated and characterized. Both theoretical and experimental results highlight the interest of using a periodic structure for high frequency ultrasonic applications.     

Thickness optimization of a multilayered structure on the coupling surface between a structure and an acoustic cavity

This paper describes a new design method to optimize thickness distribution of a multilayered structure which is located on the coupling surface between a structure and an acoustic cavity. The design method is based on the concept of the density approach in topology optimization incorporating a transfer matrix for a multilayered structure that includes a poroelastic media layer. The one-dimensional transfer matrix adopted here is an approximate representation addressing vibro-acoustic effects inherent in a multilayered structure, and balances calculation resources and desired accuracy. Applying the transfer matrix representation as boundary conditions on the coupling surface between a structure and an acoustic cavity, the modified equilibrium equation of the vibro-acoustic system is derived which is approximately but efficiently solved by the modal approach. In this study, the problem of minimizing the acoustic pressure within the cavity over the prescribed frequency range is formulated under the volume constraint of the poroelastic media layer. The continuous approximation of thickness distribution is assumed, and the thickness of the poroelastic media layer at each nodal point is chosen as design variables. Numerical results show that an acoustic response is significantly reduced by the optimal thickness distribution having a total weight equal to or less than that in the initial uniform thickness. These demonstrate that the proposed method is effective to design the optimal thickness distribution of a multilayered structure.     

Acousto-optic interaction in a non-homogeneous acoustic field excited by a wedge-shaped transducer

The article is devoted to theoretical analysis of light diffraction in a non-homogeneous acoustic field created by a wedge-shaped piezoelectric transducer. Relationships describing electrical, acoustic and acousto-optic properties of the acousto-optic cell are derived in the approximation of a small thickness of the piezoelectric plate. Principal characteristics of acousto-optic interaction are examined such as dependences of the light diffraction efficiency on the phase mismatch and the acoustic wave amplitude. It is shown that the acoustic field has a complicated amplitude-phase structure changing with the acoustic frequency. It is demonstrated that the diffraction efficiency in the Bragg regime can approach 100% in spite of a noticeable phase mismatch. The appropriate optimal values of ultrasound power and incidence angles of light are found.     

声波作用下球形颗粒外声流分布的数值模拟

综合考虑声学边界层内的热损失和黏性损失,建立处于平面驻波声压波节位置二维球形颗粒外声流计算模型,利用分离时间尺度的数值方法对颗粒外声流流场特征进行模拟.将模拟结果与相应的解析解和实验结果对比,验证了数值模拟的可靠性.在此基础上,研究了雷诺数Re和斯特劳哈尔数Sr对球形颗粒声学边界层内二阶声流流场结构、涡流强度及范围的影...     

Acoustic cloak with duplex communication ability constructed by multilayered homogeneous isotropic materials

Based on the effective medium theory, we propose a practical implementation of a cylindrical acoustic cloak with a concentric alternating multilayered structure of homogeneous isotropic materials, which can perfectly mimic the ideal radius-dependent and anisotropic ordinary lens cloak. The proposal exhibits near-ideal cloaking performance such as low-scattering and shadow-reducing in a wide frequency range, thus it can hide an object from the detection of acoustic waves. The acoustic wave can pass through the cloaking shell with an unchanged wavefront shape, which endues the cloaked object with duplex communication ability. More simulations on the acoustic far-field scattering patterns and the total scattering cross-section are performed to investigate the layer number and the frequency dependence of the cloaking effect, and the results show that the thinner layers exhibit a better cloaking effect. The proposal may significantly facilitate the experimental demonstration of the acoustic cloak.     

Impedance of pistons on a two-layer medium in a planar infinite rigid baffle

An integral transform technique is used to develop a general solution for the impedance of rigid pistons acting on a two-layer medium. The medium consists of a semi-infinite acoustic fluid on a viscoelastic thick plate in a rigid infinite baffle. The stresses acting on the planar baffle, as a result of piston motion, are determined using theory of linear elasticity and are therefore unrestricted in terms of applicable frequency range. The special case of a circular piston is considered and expressions for the self-and mutual impedances are developed and evaluated numerically. Numerical results are compared with classical piston impedance functions and finite-element model results. At low frequencies (k(0)a<1), the self-impedances vary significantly from the classical piston impedance functions due to the shear properties of the viscoelastic medium. In the midfrequency range (1相似文献   

Analysis of the acoustic field excited by a vibrosource in an elastic layer and ambient medium

The results of numerical analysis of the acoustic field excited in an elastic layer and in ambient media by an oscillating infinitely extensive point dipole source with the moment oriented parallel to the laminar structure layers are given. Spatial distribution of the amplitude of the SH-wave field, propagating in the direction perpendicular to the moment, in the layer and beyond it is analyzed. The problem is solved in a two-dimensional statement at different ratios of parameters of elastic rigidity of the inner and outer regions of the laminar structure at different vibrational frequencies.     

The acoustic modes of a rectangular cavity containing a rigid,incomplete partition

A theoretical and experimental study of the acoustic modes of a rectangular cavity containing a rigid, incomplete partition is presented. The theoretical results are obtained by using finite element techniques. It is shown that component mode synthesis techniques, developed for dynamic structural analysis, can be used for acoustic analysis to increase efficiency. The experimental measurements were made on a Perspex model. Good agreement is shown between theory and experiment.