Thermoelectric properties of Bi2Se3/Bi2Te3/Bi2Se3 and Sb2Te3/Bi2Te3/Sb2Te3 quantum well systems

In this work, we develop a theory of thermoelectric transport properties in two-dimensional semiconducting quantum well structures. Calculations are performed for n-type 0.1 wt.% CuBr-doped Bi₂Se₃/Bi₂Te₃/Bi₂Se₃ and p-type 3 wt.% Te-doped Sb₂Te₃/Bi₂Te₃/Sb₂Te₃ quantum well systems in the temperature range 50–600 K. It is found that reducing the well thickness has a pronounced effect on enhancing the thermoelectric figure of merit (ZT). For the n-type Bi₂Se₃/Bi₂Te₃/Bi₂Se₃ with 7 nm well width, the maximum value of ZT is estimated to be 0.97 at 350 K and for the p-type Sb₂Te₃/Bi₂Te₃/Sb₂Te₃ with well width 10 nm the highest value of the ZT is found to be 1.945 at 440 K. An explanation is provided for the resulting higher ZT value of the p-type system compared to the n-type system.     

Energy formation of antisite defects in doped Sb2Te3 and Bi2Te3 crystals

The free carrier concentration of the Sb_2−xIn_xTe₃, Bi_2−xIn_xTe₃ and Bi₂Te_3−xS_x crystals has been determined from the values of the Hall constants and the free carrier concentration of the Sb_2−xTl_xTe₃ has been calculated from the plasma resonance frequency; with increasing value of x, the hole concentration decreases. As the incorporation of the elements In, Tl and S into the lattice Sb₂Te₃ or Bi₂Te₃, respectively, gives rise to the uncharged defects In^x_Sb, Tl^x_Sb, In^x_Bi and S^x_Te, the x causes the decrease of the antisite defects concentration. The proven effect is explained in the following way: the antisite defects can be created only in crystals whose atoms are bound by weakly polarized bonds. The incorporation of In, Tl and S atoms into the crystal lattice of Sb₂Te₃ or Bi₂Te₃ increases the bond polarity, the ionicity of ternary crystals increases. This unfavorably affects the increase of antisite defects whose concentration decreases. The change of the bond polarity is considered from the changes discovered in the formation energy of antisite defects of the above mentioned ternary crystals.     

Growth behavior of Bi2Te3 and Sb2Te3 thin films on graphene substrate grown by plasma‐enhanced chemical vapor deposition

A comparative study of the substrate effect on the growth mechanism of chalcogenide Bi₂Te₃ and Sb₂Te₃ thin films was carried out. Obvious microstructural discrepancy in both the as‐deposited Bi₂Te₃ and Sb₂Te₃ thin films was observed when grown on graphene or SiO₂/Si substrate. Bi₂Te₃ and Sb₂Te₃ thin films deposited on the graphene substrate were observed to be grown epitaxially along c‐axis and show very smooth surface compared to that on SiO₂/Si substrate. Based on the experimental results of this study, the initial adsorption sites on graphene substrate during deposition process, which had been discussed theoretically, could be demonstrated empirically.     

Characterization of Mn-doped Sb1.5Bi0.5Te3 single crystals

Abstract

Single crystals of (Sb_0.75Bi_0.25)_2-xMn_xTe₃ (x = 0.0–0.05) were characterized by X-ray diffraction, measurements of reflectance in the plasma resonance frequency region, Hall coefficient, electrical conductivity, and Seebeck coefficient. It was found that Mn atoms in the crystal structure of Sb_1.5Bi_0.5Te₃ behave like acceptors; the increase in the hole concentration is explained by the formation of substitutional defects of Mn'_Sb and Mn'_Bi in the crystal lattice of the studied crystals.     

High pressure transport characteristics of Bi2Te3, Sb2Te3, and BiSbTe3

This paper presents ambient and high pressure measurements of transport properties of the Bi₂Te₃–Sb₂Te₃ series of materials. The electrical resistivity, thermal conductivity, and Seebeck coefficient have been measured on both end compounds and the direct solid solution of the two at pressure up to 10 GPa. An additional discussion involving the high pressure structure will be presented. From this, it was determined that these materials undergo at least two structural phase transitions between 0 and 20 GPa and a discussion is presented regarding this and the changes in the transport properties.     

A tunneling spectroscopy study of the temperature dependence of the forbidden band in Bi2Te3 and Sb2Te3

Tunneling measurements of dI/dV, d ² I/dV ², and d ³ I/dV ³ were formed along the C ₃ axis (normally to layers) for Bi₂Te₃ and Sb₂Te₃ layered semiconductors in the temperature range 4.2<T>29 5 K. Temperature dependences of the forbidden band energy E _g were obtained. The forbidden band energy in Bi₂Te₃ was 0.20 eV at room temperature and increased to 0.24 eV at T=4.2 K. The E _g value for Sb₂Te₃ was 0.25 eV at 295 K and 0.26 eV at 4.2 K. The distance between the top of the higher valence band of light holes and the top of the valence band of heavy holes situated lower was found to be ΔE _V≈19 meV in Bi₂Te₃; this distance was independent of temperature. The conduction bands of Bi₂Te₃ and Sb₂Te₃ each contain two extrema with distances between them of ΔE _c≈25 and 30 meV, respectively.     

Structure and electrical properties of Sb2Te3 and Bi0.4Sb1.6Te3 metastable phases obtained by HPHT treatment

We have obtained the metastable phase of the thermoelectric alloy Bi_0.4Sb_1.6Te₃ with electron type conductivity for the first time using the method of quenching under pressure after treatment at P=4.0 GPa and T=400–850 °C. We have consequently performed comparative studies with the similar phase of Sb₂Te₃. The polycrystalline X-ray diffraction patterns of these phases are similar to the known monoclinic structure α-As₂Te₃ (C2/m) with less monoclinic distortion, β ≈ 92°. We have measured the electrical resistivity and the Hall coefficient in the temperature range of T=77?450 K and we have evaluated the Hall mobility and density of charge carriers. The negative Hall coefficient indicates the dominant electron type of carriers at temperatures up to 380 K in the metastable phase of Sb₂Te₃ and up to 440 K in the metastable state of Bi_0.4Sb_1.6Te₃. Above these temperatures, the p-type conductivity proper to the initial phases dominates.     

Electric quadrupole interaction of111Cd in the system Sb1−xMx (M=Ag,Cd,In,Sn), Sb2Te3, Bi2Te3 and In2Te3

We have performed TDPAC-measurements to investigate the static quadrupole interaction of₁₁₁Cd in the classic semimetal Sb. The coupling constant depends on the concentration of small amounts of metal admixtures. The only exception is the system Sb_1–xAg_x. The temperature dependence of the efg in the narrow gap semiconductors Sb₂Te₃ and Bi₂Te₃ is similar to that one in Te. In contrast to these results the efg in the III–VI-semiconductor In₂Te₃ is temperature independent.     

Density functional study of Bi2Te3 and Bi4Te6 molecules

Results of a density functional study for the molecules Bi₂Te₃ and Bi₄Te₆ are reported here. For Bi₂Te₃, calculations yield eight stable conformations. For Bi₄Te₆, eight stable isomers are identified. Equilibrium geometries, adiabatic ionisation potentials, atomisation energies, and vibrational bands are estimated. The lowest energy conformations in both cases are clusters of C_s symmetry with all Te atoms two-fold coordinated and all Bi atoms three-fold coordinated. The predicted low energy conformation for Bi₄Te₆ has alternating rows of Bi and Te atoms. This molecule seems a reasonable precursor to solid bismuth telluride, which has alternating Bi and Te layers.     

Fermi surface and thermoelectric power of (Bi1−x Sbx)2Te3<Ag, Sn> mixed crystals

The Fermi surface anisotropy of (Bi_1?x Sb_x)₂Te₃ single crystals (0.25 ≤ x ≤ 1) was studied by analyzing the angular dependence of the frequency of Shubnikov-de Haas oscillations and the effect of tin and silver doping on the thermoelectric power in these crystals in the temperature range 77 ≤ T ≤ 300 K. It was shown that silver doping of (Bi_1?x Sb_x)₂Te₃ mixed crystals produces acceptors, while silver in Bi₂Te₃ acts as a donor. Tin also exhibits acceptor properties. Both tin and silver doping of p-(Bi_1?x Sb_x)₂Te₃ mixed crystals decrease the thermoelectric power due to an increase in the hole concentration.     

Sb2Te3 纳米结构的制备与表征

以室温热电性能优异的传统热电材料Sb₂Te₃为研究对象,利用化学气相沉积法制备Sb₂Te₃单晶纳米结构,并研究其生长机理.实验结果表明,不加催化剂时Sb₂Te₃易生长成六方纳米盘,在金催化剂条件下定向生长成纳米线.Sb₂Te₃的形貌与其晶体结构和生长机理有关.Sb₂Te₃为三角结构,Sb和     

Temperature dependence of the Raman spectra of Bi2Te3 and Bi0.5Sb1.5Te3 thermoelectric films

The temperature dependence of the Raman spectra of Bi₂Te₃ and Bi_0.5Sb_1.5Te₃ thermoelectric films was investigated. The temperature coefficients of the E_g(2) peak positions were determined as –0.0137 cm^–1/°C and –0.0156 cm^–1/°C, respectively. The thermal expansion of the crystal caused a linear shift of the Raman peak induced by the temperature change. Based on the linear relation, a reliable and noninvasive micro‐Raman scattering method was shown to measure the thermal conductivity of the thermoelectric films. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

An analysis of the thermoelectric efficiency of n-(Bi,Sb)2(Te,Se,S)3 solid solutions within an isotropic scattering model

A study is reported on the thermoelectric properties of n-type solid solutions Bi₂Te_3?y Se_y (y=0.12, 0.3, 0.36), Bi_2?x Sb_xTe_3?y Se_y (x=0.08, 0.12; y=0.24, 0.36), and Bi₂Te_3?z S_z (z=0.12, 0.21) as functions of carrier concentration within the 80-to 300-K range. It has been established that the highest thermoelectric efficiency Z is observed in the Bi₂Te_3?y Se_y (y=0.3) solid solution containing excess Te at optimum carrier concentrations (0.35×10¹⁹ cm^?3) and at temperatures from 80 to 250 K. The increase in Z in the Bi₂Te_3?y Se_y solid solution compared with Bi_2?x Sb_xTe_3?y Se_y and Bi₂Te_3?z S_z is accounted for by the high mobility μ₀, an increase in the effective mass m/m ₀ with decreasing temperature, the low lattice heat conductivity κ_L, and the weak anisotropy of the constant-energy surface in a model assuming isotropic carrier scattering.     

Fundamental band edge optical absorption in Bi<Subscript>0.5</Subscript>Sb<Subscript>1.5</Subscript>Te<Subscript>3</Subscript>

Spectra of optical absorption in Bi_0.5Sb_1.5Te₃ films grown on mica and KBr substrates have been investigated for T = 145 and 300 K. The data obtained have been analyzed together with the data of investigations on the fundamental absorption edge for Bi₂Te₃ available in the scientific literature. It has been revealed that the interband absorption spectra for both Bi_0.5Sb_1.5Te₃ and Bi₂Te₃ represent a superposition of two components corresponding to direct and indirect allowed optical transitions. In this case, the least energy gap separating the valence band and the conduction band is direct for Bi_2−xSb_xTe₃ (x ≤ 1.5, T = 300 K). For Bi_0.5Sb_1.5Te₃ the temperature variation rates have been estimated for the thresholds of direct and indirect interband transitions. It has been shown that this solid solution is direct gap solution at T ≥ 145 K. Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 7, pp. 50–52, July, 2008.     

Local atomic structure in molten Si3Sb2Te3 phase change material

By means of ab initio molecular dynamics calculations, we have studied the local structures of liquid and amorphous Si₃Sb₂Te₃. The results show that all the constitute elements in liquid Si₃Sb₂Te₃ are octahedrally coordinated. While in amorphous state, Sb and Te atoms are mainly octahedrally coordinated and Si atoms are mainly tetrahedrally coordinated. In both states, Si is mainly homo-bonded by Si. Finally, we proposed a phase separation model for liquid and amorphous Si₃Sb₂Te₃, which is responsible for the good performance of Si₃Sb₂Te₃ alloy as a phase change material.     

Point defects in Sb2Te3 crystals doped with Cd atoms

The room temperature values of the electrical conductivity, Seebeck coefficient, as well as the reflectivity curve in the plasma resonance frequency region, were determined for undoped and Cd-doped Sb₂Te₃ crystals. A quantitative analysis of the cadmium content in the samples was carried out using the atomic absorption technique. In comparing the changes in the hole concentration, as determined from the measured parameters, one has found that only about one third of the total number of built-in atoms contributes to the increase in the hole concenration. The observed phenomena are consistent with the assumption that the active defects are most probably Cd-Sb substitutional defects, i.e. Cd atoms in the antimony sublattice, whereas a larger fraction of the number of Cd atoms occupies the van der Waals sites of the Sb₂Te₃ lattice and thus forms uncharged defects.     

Effect of heat treatment on the structure and the thermoelectric properties of Sb<Subscript>0.9</Subscript>Bi<Subscript>1.1</Subscript>Te<Subscript>2.9</Subscript>Se<Subscript>0.1</Subscript> thin films and composites based on them

This work considers the effect of vacuum annealing on the thermoelectric properties of Sb_0.9Bi_1.1Te_2.9Se_0.1 thin film and Sb_0.9Bi_1.1Te_2.9Se_0.1–C composites with various carbon contents produced by ion-beam deposition in an argon atmosphere. The electrical resistivity and the thermopower of Sb_0.9Bi_1.1Te_2.9Se_0.1–C nanocomposites are found to be dependent on not only the carbon concentration but also the type and the concentration of intrinsic point defects of the Sb_0.9Bi_1.1Te_2.9Se_0.1 solid solution, which determine the type of conductivity of Sb_0.9Bi_1.1Te_2.9Se_0.1 granules. The power factors are estimated for films of Sb_0.9Bi_1.1Te_2.9Se_0.1 solid solution and films of Sb_0.9Bi_1.1Te_2.9Se_0.1–C composites and found to have values comparable with the values for nanostructured materials on the basis of (Bi,Sb)₂(Te,Se)₃ solid solutions.     

Electronic structures and thermoelectric properties of La or Ce-doped Bi2Te3 alloys from first principles calculations

Thermoelectric properties of La or Ce-doped Bi₂Te₃ alloys were systematically investigated by ab initio calculations of electronic structures and Boltzmann transport equations. The Seebeck coefficient of p-type LaBi₇Te₁₂ and La₂Bi₆Te₁₂ was larger than that of Bi₂Te₃, because La doping increased the effective mass of carriers. On the other hand, the electrical conductivity of LaBi₇Te₁₂ and La₂Bi₆Te₁₂ decreased, which caused a reduction of power factor of these La-doped Bi₂Te₃ alloys in comparison with Bi₂Te₃. The influence of Ce doping on the band structure and thermoelectric properties of Bi₂Te₃ was similar to that of La doping. The theoretical calculation provided an insight into the transport properties of La or Ce-doped Bi₂Te₃-based thermoelectric materials.     

相变存储材料Ge1Sb2Te4和Ge2Sb2Te5薄膜的结构和电学特性研究

采用射频磁控溅射方法制备了两种用于相变存储器的Ge₁Sb₂Te₄和Ge₂Sb₂Te₅相变薄膜材料,对其结构、电学输运性质和恒温下电阻随时间的变化关系进行了比较和分析.X射线衍射(XRD)和原子力显微镜(AFM)的结果表明:随着退火温度的升高,Ge₁Sb₂Te₄薄膜逐步晶化,由非晶态转变为多晶态,表面出现均匀的、 关键词： 硫系相变材料 1Sb₂Te₄')" href="#">Ge₁Sb₂Te₄ 2Sb₂Te₅')" href="#">Ge₂Sb₂Te₅     

Specific features in the behavior of the effective mass and mobility in n-(Bi, Sb)2(Te, Se, S)3 solid solutions

The thermoelectric properties of the multicomponent solid solutions Bi_2?x Sb_xTe_3?y?z Se_yS_z with substitutions of atoms in both sublattices of Bi₂Te₃ were studied. The data obtained in studies of the galvanomagnetic effects in weak magnetic fields were used to properly take into account the change in the carrier scattering mechanisms due to the substitutions Sb → Bi, Se, and S → Te in the solid solutions. The mobility μ₀ with inclusion of the degeneracy, the effective density-of-states mass m/m ₀, and the lattice thermal conductivity κ_L were calculated. An analysis was carried out for the quantities μ₀, m/m ₀, and κ_L in the solid solutions under study as functions of the composition, carrier concentration, and temperature.