Kinetics and possible mechanism of hydrogen chloride oxidation over supported copper-containing salt catalysts: II. Kinetics of HCl oxidation in the deacon and methane oxychlorination reactions over the CuCl2-KCl-LaCl3 catalyst

The kinetics of HCl oxidation at 350–425°C over the supported CuCl₂-KCl-LaCl₃ catalyst has been investigated using a gradientless technique. The HCl oxidation kinetics in the Deacon and methane oxychlorination reactions has been studied in order to substantially extend the \(Cl_2 \left( {P_{Cl_2 } } \right)\) partial pressure variation range. When the reaction rate is independent of P _HCl, HCl oxidation on the copper-potassium catalysts is described by the same rate equation, irrespective of whether the catalyst contains lanthanum or not. The introduction of lanthanum chloride increases the HCl oxidation rate by one order of magnitude. The rate equation obtained has significant advantages over the equation corresponding to the Kenney-Slama equation. The kinetic features of HCl oxidation over the lanthanum-containing catalyst, whether the process depends on P _HCl or not, can be explained in terms of the superposition of the Kenney-Slama dissociative mechanism and the catalytic mechanism suggested here. The role of lanthanum chloride in both HCl oxidation pathways is considered.     

The role of octanol in the extraction of hydrochloric acid by trilaurylamine dissolved in benzene

The extraction of hydrochloric acid by trilaurylamine (TLA) dissolved in benzene was studied in the presence and in absence of n-octanol. The extraction of HCl was found to be enhanced by the addition of octanoi to the organic phase. In order to explain this effect by means of the law of mass action, the systems TLA-HCL-benzene and n-octanol-HCl-benzene as well as TLA-octanol-benzene were also studied. It was found that TLA reacts with octanol to form a complex, TLAROH, while the octanol itself associates in benzene to form dimers and tetramers, although it does not extract HCl alone from the dilute solutions used in the present study. The enhancement of the extraction of HCl by TLA upon the addition of n-octanol could be described by the formation of the species TLA·ROH·HCl and its stability constant was determined.     

Effect of Cl substituent in the aromatic tetracycline ring on its reactivity with solvated electrons

Decomposition yields of tetracycline hydrochloride /TC.HCl/ and chlorotetracycline hydrochloride /ClTC?HCl/ in methanol solution saturated with Ar or N₂O were determined. Rate constants of the reaction e_s with some antibiotics were obtained: $$\begin{gathered} k/e_s^ - + ClTC \cdot HCl/ = 2 \cdot 49 \times 10^8 dm^3 \cdot mole^{ - 1} \cdot s^{ - 1} ; \hfill \\ k/e_s^ - + TC \cdot HCl/ = 2 \cdot 86 \times 10^8 dm^3 \cdot mole^{ - 1} \cdot s^{ - 1} \cdot \hfill \\ \end{gathered} $$ On the basis of the diffence between decomposition yields: ΔG=G_?TC.HCl^?G?ClTC.HCl′ 7-C?Cl group decomposition yield and the rate constant $$k/e_s^ - + Cl - C - 7/ = 7 \cdot 94 \times 10^8 dm^3 \cdot mole^{ - 1} \cdot s^{ - 1} $$ were determined. It was demonstrated by¹H NMR that the radical formed by degradation of 7-C?Cl group is recombined with the H atoms leading to ClTC.HCl being converted into tetracycline hydrochloride /TC.HCl/.     

Preparation and evaluation of PANI/PTT electromagnetic shielding fabric by in-situ chemical polymerization

To prepare the flexible and stretchable electromagnetic shielding (EMS) fabric with environmental stability, this paper uses polytrimethylene terephthalate (PTT) fabric as substrate, the aniline monomer as raw material, hydrochloric acid (HCl) as the doping agent, ammonium persulfate (APS) as the oxidant to produce polyaniline (PANI)/PTT electromagnetic shielding fabric by in-situ chemical polymerization. It studies the influence of APS and HCl concentration on the surface electrical resistance and the absorption loss of electromagnetic shielding fabric. It can be observed that an increasing APS and HCl facilitate the absorption and spread of PANI into PTT fabric to form a conductive network, and improve the absorption loss efficiency, while the excess APS and HCl will hinder the PANI polymerization. The high electrical conductivity and absorption loss of the PANI/PTT fabric are obtained at the concentration of An 0.4 M, APS 0.4 M, HCl 1.25 M, and polymerization reaction time 120 min. Meanwhile, in-situ polymerization of PANI does not introduce new impurities and destroy the molecular structure of PTT.     

A photoionization study of the van der Waals molecule C2H4 · HCl

The dissociation energy of the C₂H₄ · HCl van der Waals complex was determined to be 3.18±0.73 kcal mol^?1 by a dissociative photoionization technique. C₂H₄ · HCl was produced by free expansion of a 1:4 mixture of C₂H₄ in HCl and the clusters were ionized with tunable synchrotron radiation. The photoionization efficiency function of (C₂H₄ · HCl)⁺ from C₂H₄ · HCl was determined between 600 and 1,300 Å and the onset for (C₂H₄ · HCl)⁺ was established as 1,163±2 Å = 10.66±0.02 eV; these values give ΔH _f ⁰ (C₂H₄ · HCl) = ?10.7±0.7 kcal mol^?1 and ΔH _f ⁰ (C₂H₄·HCl⁺)=235.1±0.9 kcal mol^?1. A complex ion dissociation energyD ₀(C₂H₄ · HCl⁺) = ?0.3±0.9 kcal mol^?1 was calculated from the results. The major features on the PIE curve for C₂H₄ · HCl⁺ can be analyzed in terms of the known energetic features of C₂H ₄ ⁺ and HCl. An extended energy diagram for the C₂H₄ + HCl system is presented.     

On the determination of HCl+ (A,v′) vibrational populations from HCl+ (A→X) fluorescence spectra: direct comparison between photoionization and penning ionization

Using a beam apparatus, we have measured the HCl⁺ (A,v′→X,v″) fluorescence spectra of HCl⁺ (A,v′) ions formed in HeI (58.4 nm), and NeI (73.6 nm) photoionization and, for the first time, in He (2³ S) Penning ionization under single collision conditions with a wavelength bandwidth around 1 nm. In addition, we have studied Ne (3s ³ P _{2, 0}) Penning ionization of HCl at three different collision energies. The procedure and the problems in extracting HCl⁺ (A,v′) vibrational populations from the data are discussed in some detail. Thedirect comparison of photoionization and Penning ionization data allows definitive conclusions to be drawn on the question whether final state interactions in the Penning reaction change the “nascent” vibrational population (determined by electron spectrometry); for He (2³ S)+HCl, such changes are shown to be absent within the experimental uncertainty (<±10%). For Ne (3s ³ P _{2, 0})+HCl, the HCl⁺ (A,v′=0, 1) populations are also found to be close to those measured by electron spectrometry and essentially independent of collision energy in the range 34–96 meV. From measurements of the fluorescence intensity as a function of HCl density, we have evidence for a fast loss of HCl⁺ (A,v′) ions in collisions with HCl (rate constant around 5·10^?9 cm³s^?1).     

Penning ionization electron spectrometry of hydrogen chloride

An electron spectrometric study has been performed on HCl using metastable helium and neon atoms as well as neon resonance photons. High resolution electron spectra were obtained with two different beam apparatuses for a mixed He(2¹ S, 2³ S) beam, a pure He(2³ S) beam, and, for the first time, state-selected pure Ne(3s ³ P ₂) and pure Ne(3s ³ P ₀) beams, and for NeI resonance photons. For the system He(2³ S)+HCl the vibrational populationsP(υ′) of the formed HCl⁺ (X ²∏ _i , υ′) and HCl⁺ (A ²Ω⁺, υ′) ions are found to differ from the Franck-Condon factors for unperturbed potentials, indicating slight bond stretching in HCl upon He(2³ S) approach. For He(2¹ S)+HCl the vibrational peak shapes and vibrational populations are substantially different from the He(2³ S) case, pointing to an additional, charge exchanged interaction (He⁺+HCl^?) in the entrance channel of the former system. For the first time, we have detected the electrons in both the He(2¹ S)+HCl and He(2³ S)+HCl spectra associated with the major mechanism for the formation of Cl⁺ ions: energy transfer to repulsive HCl** Rydberg states, dissociating toH(1s) and autoionizing Cl**(¹ D ₂ nl) atoms. For both Ne(³ P ₂)+HCl and Ne(³ P ₀)+HCl, the populationsP(υ′) of both final molecular states HCl⁺ (X, A) agree closely with the Franck-Condon factors at the average relative collision energyē _coll=55 meV and, for HCl⁺ (A ²Ω⁺), also atē _coll=130 meV.     

Separation of tin from some metals by extraction chromatography

Much attention has been devoted to Sn (IV) strongly retained on the TBP-Daiflon column from 2M HCl in extraction chromatography. The separations of Sn?Cu, Zn, As, Cd, Sb, Pb,¹¹³Sn-¹²⁵Sb,¹¹³Sn-^113mIn (^113mIn milking) and Sn?Hg?Fe were successfully achieved without any contamination. In the separations, except for the last, only tin was retained separately on the column upon passing the mixed solution. The daughter indium was eluted with 0.5M HCl. In the last separation, iron was eluted with 0.5 M HCl, tin with 0.1M HCl and mercury with 2M HNO₃, for these metals retained on the column. Radioactive tracers for tin, iron, mercury and antimony were used.     

Antitumoral and MMP-2 inhibition activity of raloxifene or tamoxifen loaded nanoparticles containing dimethyl-β-cyclodextrin

A new nanoparticle formulation has been developed by using dimethyl-β-cyclodextrin (DM-β-CD) with raloxifene HCl or tamoxifene citrate. Both drugs are insoluble in water and represent as low bioavailibilities when given orally. Tamoxifen has an FDA approval for breast cancer prevention and the treatment. Raloxifene is approved for osteoprosis treatment. Both drugs were selected as a model drug antitumoural activity and MMP-2 inhibition studies were evaluated on breast cancer cell lines MCF-7 and MDA-MB 231. MMP-2 is known to be responsible for tumour invasion and initation the of angiogenesis. DM-β-CD and sodium taurocholate (NaTC) have been used as absorption enhancers to increase penetration effect of raloxifene/tamoxifen on the tumour cells and aimed to provide high antitumoral activity and MMP-2 inhibition results by developed nanoparticle formulations. The effects of two absorption enhancers were compared. The highest antitumoral activity was observed for DM-β-CD—raloxifene HCl nanoparticle formulation and also MMP-2 enzyme inhibit effectively.     

Influence of HCl on the stability of liquid lamellae between two colliding bubbles in aqueous solutions ofn-fatty acids

The effect of HCl on life time of liquid lamellae created between two colliding bubbles in aqueous solutions ofn-fatty acids were studied. The results show, that the addition of HCl has a pronounced influence on life time of the lamellae. At low fatty acid concentration the lifetime of the lamellae in the acidified solution is higher than in the nonacidified solution, but at higher fatty acid concentration the effect reverses. The analysis of these experimental results show that the characteristic influence of HCl on lamellae lifetime can be explained by the formation of distinct association states of the fatty acids in the liquid phase at different concentration ranges. The results are discussed with respect to bubble coalescence in gas-liquid contactors.     

Chlorine K shell photoabsorption spectra of gas phase HCl and Cl2 molecules

High resolution photoabsorption spectra of HCl and Cl₂ have been measured near the chlorineK edge in the 2810–2850 eV photon energy range. Below the ClK edge, the strongest resonance is interpreted as a simple core excitation into the unoccupied σ* valence orbital for both molecules, leading to a markedly repulsive state. Higher resonances due to low lying Rydberg states, are observed in both systems, but with a larger oscillator strength for HCl as compared to Cl₂. In Cl₂, the σ* orbital is deep enough to avoid any mixing with Rydberg orbitals. In HCl, we observe the dipole forbidden Cl 1s → 4s transition which denotes a strong 4s–4p hybridization. Above the ClK edge, the multiplet features seen for HCl are analysed in terms of double-core-valence excited vacancy states. In Cl₂, their counterpart are found very close to the ionization threshold because of the deep σ* orbital and possibly because the excited core and valence electrons originates either from the same atomic site or from different ones.     

TiO2 and TiO2/SiO2 nanoparticles obtained by sol–gel method and applied on dye sensitized solar cells

In this work we show the synthesis and characterization of TiO₂ and TiO₂/SiO₂ nanoparticles synthesized by sol–gel method using HF and HCl as catalysts. The obtained nanoparticles were analyzed by N₂ adsorption–desorption isotherms, transmission electronic microscopy, Ultraviolet–visible spectroscopy and X-ray diffractometry. Mesoporous, homogeneously polycondensed TiO₂/SiO₂ materials, containing nanocrystalline anatase phase with band gap similar to pure titania were obtained. Films of the powdered oxides were applied to assemble dye sensitized solar cells that presented electrical parameters, Fill Factor and efficiencies similar to devices obtained by only TiO₂. The sol–gel route arises as an alternative way to prepare TiO₂/SiO₂ materials for solar cells.     

Extraction and separation of60Co and65Zn halides from H2SO4 with TBP and amberlite LA-2

A systematic study is presented on the extraction of⁶⁰Co and⁶⁵Zn bromides and chlorides from H₂SO₄ with tri-n-butyl phosphate (TBP) and Amberlite LA-2. It has been found that the presence of a little HBr or HCl enhances the extraction of the two isotopes with both solvents. The extractions of⁶⁰Co and⁶⁵Zn have been studied as functions of the acidity (HBr, HCl or H₂SO₄) in the aqueous phase, and of the diluent and solvent concentrations in the organic phase. The presence of water-miscible alcohols or acetone enhances extraction. A suggested extraction mechanism is presented in the light of the obtained results.     

Separation of metallic impurities from uranium by anion exchange on Dowex 1×8 resin

The separation of metallic impurities from uranium by anion exchange with a Dowex 1×8 resin has been investigated. The following elements can be quantitatively separated from 400 mg uranium using a 1 cm diameter 15 or 30 cm long column. The elements Ag, Al, Ba, Ca, Cr, Cs, K, Mg, Mn, Na, Ni, Rb, REE, Sc, Th, Ti and Y can be separated by eluting the elements with conc. HCl. Uranium is retained by the resin. Al, Ca, Cd, Co, Cr, Cu, Fe, Mg, Mn, Na, REE and V can be separated by eluting with 0.01 N H₂SO₄. Uranium is retained by the resin. Cd and Zn can be separated by first eluting uranium with 0.5 N HCl and then eluting Cd and Zn with 1 N NH₃. Hf, Zr and V can be separated by eluting with 5 N HCl but some uranium contamination is unavoidable.     

Separation of metal halide pairs using Amberlite LA-2 and tri-N-butyl phosphate

A systematic study was performed on the extraction and separation of cadmium from iron halides in pure halo-acid solutions and their mixtures with H₂SO₄ and H₃PO₄. As solvents Amberlite LA-2, TBP, nitrobenzene and HDEHP were used. Recommended separation media for the amine are 2M HCl, 1M HBr, 1.12M HCl?2M H₂SO₄, 0.64M HBr?2M H₂SO₄, 1.12M HCl?4M H₃PO₄ 0.64M HBr?7M H₃PO₄ and for TBP the medium 0.64M HBr?4M H₃PO₄ is the only suitable condition.     

Solid-phase microextraction/gas chromatography–mass spectrometry method optimization for characterization of surface adsorption forces of nanoparticles

A complete characterization of the different physico-chemical properties of nanoparticles (NPs) is necessary for the evaluation of their impact on health and environment. Among these properties, the surface characterization of the nanomaterial is the least developed and in many cases limited to the measurement of surface composition and zetapotential. The biological surface adsorption index approach (BSAI) for characterization of surface adsorption properties of NPs has recently been introduced (Xia et al. Nat Nanotechnol 5:671–675, 2010; Xia et al. ACS Nano 5(11):9074–9081, 2011). The BSAI approach offers in principle the possibility to characterize the different interaction forces exerted between a NP's surface and an organic—and by extension biological—entity. The present work further develops the BSAI approach and optimizes a solid-phase microextraction gas chromatography–mass spectrometry (SPME/GC-MS) method which, as an outcome, gives a better-defined quantification of the adsorption properties on NPs. We investigated the various aspects of the SPME/GC-MS method, including kinetics of adsorption of probe compounds on SPME fiber, kinetic of adsorption of probe compounds on NP's surface, and optimization of NP's concentration. The optimized conditions were then tested on 33 probe compounds and on Au NPs (15 nm) and SiO₂ NPs (50 nm). The procedure allowed the identification of three compounds adsorbed by silica NPs and nine compounds by Au NPs, with equilibrium times which varied between 30 min and 12 h. Adsorption coefficients of 4.66?±?0.23 and 4.44?±?0.26 were calculated for 1-methylnaphtalene and biphenyl, compared to literature values of 4.89 and 5.18, respectively. The results demonstrated that the detailed optimization of the SPME/GC-MS method under various conditions is a critical factor and a prerequisite to the application of the BSAI approach as a tool to characterize surface adsorption properties of NPs and therefore to draw any further conclusions on their potential impact on health. Graphical Abstract

The basic principle of SPME/GC-MS method for characterization of nanoparticles surface adsorption forces     

Electron attachment to HCl clusters

Negatively charged cluster ions of hydrogen chloride are formed by electron attachment to HCl clusters, which are produced in a seeded supersonic beam traversing a sustained gas discharge. Cluster ions of (HCl) _n ^? , withn=2, and tentatively withn=3 and 4 are observed. Cluster ions like Cl _n ^? , Cl _n ^? (HCl) _m , and withAr attached to them are also seen. The relevance to radiation chemistry of HCl if briefly discussed. Atoms evaporating from the hot, thoriated tungsten filament of the glow discharge lead to clusters such as Th _n ^? and its oxides.     

Aminophylline: thermal characterization and its inhibitory properties for the carbon steel corrosion in acidic environment

Aminophylline (AMF) was studied as corrosion inhibitor for carbon steel in 1.0 mol L^?1 HCl solution using electrochemical measurements associated with UV–Vis spectrophotometry and optical microscopy. Simultaneous thermogravimetry/derivative thermogravimetry and differential scanning calorimetry analysis was performed in order to determine the temperature range in which AMF is an effective inhibitor, without the decomposition risk that could change the inhibition mechanism. Thermal behaviour restricts AMF application as corrosion inhibitor for carbon steel in 1.0 mol L^?1 HCl solution at temperatures ≤45 °C where there are no significant modifications of the adsorption mechanism. According to the results of electrochemical measurements, in association with UV–Vis spectrophotometry and optical microscopy techniques, AMF is a mixed-type inhibitor for carbon steel corrosion in 1.0 mol L^?1 HCl solution, simultaneously suppressing the anodic and cathodic processes and acting via spontaneous physisorption on the metal surfaces.     

Molecular beam study of the system Kr + HCl

Angular distributions of HCl scattered off Kr have been measured at collision energiesE ranging from 66.3 to 208.7 meV. The curves exhibit a clearly resolved damped rainbow structure. In addition time-of-flight distributions of scattered HCl were measured indicating significant energy transfer. To a part of these data (E=99 meV) the parameters of the M5 potential energy surface of Hutson and Howard [3] were fitted using the infinite order sudden approximation (IOSA) and quasi classical trajectories (QCT). A comparison of QCT and IOSA results suggests applicability of the IOSA to the present system atE=99 meV. We find a well depth of ?31.8 meV (compared to Hutson and Howard's value of ?26.5 meV) at the collinear Kr ... HCl conformation and strong indication for the existence of a secondary potential minimum at the collinear Kr ... ClH conformation. The analysis of the angular distributions based on a one channel scattering calculation leads to an isotropic potential similar to the full potential energy surface cut along the 90°-conformation rather than to the spherical average or spherical limit of the surface.     

Isolation and alpha-particle spectrometric determination of238Pu and239,240Pu in sediments

A simple method is described for the isolation and determination of plutonium isotopes in sediments. The method involves leaching of sample with nitric acid and subsequent separation of plutonium on an anion-exchange column. Major matrix elements and several potential radiochemical interferences are removed during 8M HNO₃ sample loading on the column. Thorium is removed by thorough washing with 10M HCl. Plutonium (IV) is eluted with 4M HCl. Source for alpha-particle spectrometry is prepared by LaF₃ coprecipitation technique at which stage a complete separation from uranium(VI) is also achieved. The entire analytical procedure is completed in about two days.