添加剂对PVDF相转化过程及膜孔结构的影响

研究了PVP、PEG及LiCl 3种成孔添加剂下PVDF DMAc H2 O 添加剂体系的成膜机理 .无论那种添加剂的铸膜液相转换成膜过程中都存在凝胶分相和液液分相两种相变方式 ,在 30～ 6 0℃时凝胶分相在较低的非溶剂浓度下先于液液分相发生 ,LiCl作为添加剂较PEG、PVP对铸膜液有较强的致凝胶作用 ,成膜过程中凝胶分相段时间依PVP、PEG、LiCl的顺序延长 ,导致液液分相初始分相点处聚合物浓度增大 ,阻止了大孔结构的充分发展 .制得的膜依PVP、PEG、LiCl的顺序有效孔隙率和通量降低 ,结晶度升高 .以LiCl为添加剂制得的膜几乎不改变PVDF膜的疏水性 ,而以PVP或PEG为添加剂的膜隔水压差降低约 2 0kPa .     

溶剂对PVDF铸膜液相转化和微孔膜皮-亚两层结构的不同影响

采用皮-亚分步凝固成膜机理分析了3种不同溶剂对聚偏氟乙烯(PVDF)铸膜液相转化和膜结构的影响,采用浊度法测定铸膜液体系的热力学性质,沉淀速度采用光透射仪测定.结果显示,3种膜的皮层分相主要由热力学性质控制,均发生延时液固分相,生成了相互融合的球粒组成的致密皮层.3体系的亚层分相行为由动力学扩散过程控制;对于二甲基亚砜(DMSO)、N,N-二甲基乙酰胺(DMAc)体系亚层发生瞬时液液分相,结晶化对动力学过程影响小,表现为光透射曲线上分相时间t2短,生成了大孔结构为主的亚层,膜厚度、孔隙率和气通量均高、结晶度低;N,N-二甲基甲酰胺(DMF)体系亚层发生延时液液分相,结晶化对动力学过程影响大,t2长,生成蜂窝状孔结构亚层,其膜厚度、孔隙率和气通量较低,但膜的结晶度高.     

凝固浴温度对PVDF铸膜液相分离过程和膜结构的影响

采用皮-亚两步凝胶成膜机理探讨了凝固浴温度对PVDF铸膜液的相分离行为及其膜结构的影响.采用浊度法测定不同温度时铸膜液体系的热力学性质,光透射仪测定不同凝固浴温度时沉淀速率对膜的形态和性能的影响.结果显示:皮层的生成主要受热力学性质控制,随着凝固浴温度的提高,皮层由液固分相转变为液液分相,延时时间缩短,皮层由相互融合的球粒致密结构转变为多孔结构.亚层的生成主要受皮层结构和溶剂/非溶剂相互扩散的影响,膜亚层主要发生液液分相;随凝固浴温度升高,分相速率加快,大孔发展更充分,膜的孔隙率和气通量提高,但结晶度降低.     

表面喷雾N,N-二甲基乙酰胺/水-浸没沉淀相转化法制备PVDF多孔膜的结构和性能

在刮制的聚偏氟乙烯(PVDF)铸膜液上喷雾N,N-二甲基乙酰胺/水(DMAc/H₂O)混合溶液进行表面凝胶,随后将表面凝胶的液膜浸入凝固浴中使沉淀相转变成PVDF多孔膜。考察了喷雾溶液中DMAc的体积分数(φ(DMAc))对平板PVDF多孔膜结构和性能的影响。结果显示,随着φ(DMAc)增加,膜上表面的β晶含量逐渐减少,α晶含量逐渐增多,但是膜总体的结晶度逐渐增加,孔隙率和平均孔径先增加后减小。通过扫描电镜观察,喷雾了DMAc/H₂O混合溶液的PVDF膜上表面为多孔皮层,且随着φ(DMAc)的增加,上表面球形晶粒逐渐增加,断面由指状大孔结构转变为海绵状孔结构。当喷雾中φ(DMAc)=30%时,膜的水通量和牛血清白蛋白(BSA)截留率达到最大。     

内凝固浴组成对聚醚酰亚胺中空纤维膜结构和性能的影响

以N,N-二甲基乙酰胺(DMAc)为溶剂,水为外凝固浴,乙醇为内凝固浴,DMAc为内凝固浴添加剂,采用相转化法制备了聚醚酰亚胺(PEI)中空纤维膜,研究了内凝固浴组成和纺丝液浓度对膜结构和性能的影响。实验结果表明,随着内凝固浴中DMAc含量在一定范围内增加,纤维断面指状孔有所减少,内表面由无孔到有微孔出现,但膜的水通量下降,截留率不受影响;随着纺丝液浓度提高,膜的水通量下降,截留率提高。     

制膜液黏度对单皮层PVDF中空纤维膜纺制的影响

以二甲基乙酰胺(DMAc)为溶剂,制备聚偏氟乙烯(PVDF)浓度为15%的制膜液,考察了DMAc同时作为内凝胶浴时膜结构的变化.为保持纺膜过程中的稳定性,分别考察了添加剂LiCl、水以及表面活性剂对制膜液黏度的影响.实验发现添加LiCl可以大大提高制膜液的黏度,而水作为添加剂时对黏度的影响与制膜液本身的浓度有关.在不提高制膜液浓度的基础上,通过提高制膜液黏度克服了膜在纺制过程中的不稳定问题,得到阻力较小的,指状孔贯穿的单外皮层中空纤维膜.     

溶剂及凝胶浴对硝酸纤维素膜结构的影响

利用丙酮(AC)、二甲基乙酰胺(DMAc)和二甲基亚砜(DMSO)三种不同溶剂制备硝酸纤维素铸膜液。考察了溶剂的性质及凝胶浴组成对膜结构的影响,利用扫描电镜表征了膜的表面及截面结构,通过成膜过程的热力学和动力学分析解释了不同膜结构的形成原因。结果表明:溶剂的种类及凝胶浴中溶剂的含量对膜结构的影响很大,其变化规律也是不同的。     

小分子醇对PVDF／PFSA共混膜凝胶动力学、膜结构及膜性能的影响

以小分子醇为添加剂,研究了小分子醇对聚偏氟乙烯(PVDF)/全氟磺酸(PFSA)共混超滤膜凝胶动力学、结构与渗透性能的影响.结果表明:在PVDF/PFSA铸膜液中添加乙醇时,其凝胶速率随乙醇浓度的增加而加快,超滤膜通量随乙醇浓度的增加而增大;而当添加相同浓度的4种小分子醇时,初始凝胶速率差别不大,20 s后添加乙醇的铸膜液的凝胶速率最大;添加小分子醇后超滤膜的水通量大小顺序为:异丙醇<甲醇<乙醇<正丁醇.SEM照片显示在铸膜液中添加5%乙醇所制备的共混超滤膜具有较为圆整的内腔结构与均匀的孔结构.     

纤维编织管增强型中空纤维膜研究

采用二维编织技术将聚丙烯腈(PAN)长丝编织成中空纤维编织管作为增强体,分别以聚丙烯腈(PAN)和聚偏氟乙烯(PVDF)为成膜聚合物,N,N-二甲基乙酰胺(DMAc)为溶剂,聚乙烯吡咯烷酮(PVP)为添加剂,调制铸膜液,采用同心圆挤出-涂覆法制备了PAN纤维编织管同质增强型PAN中空纤维膜和异质增强型PVDF中空纤维膜.研究表明,所得PAN纤维编织管增强型中空纤维膜断裂强度最大可超过75 MPa,在伸长率10%范围内,表面分离层与增强体之间界面结合良好;表面分离层具有类似于非对称膜的结构,铸膜液可浸入纤维编织管纤维空隙中,铸膜液浸入部分固化后未影响膜的通透性能;随成膜聚合物浓度增加,膜纯水通量减小,牛血清白蛋白(BSA)截留率增大;随添加剂PVP浓度增加,膜的纯水通量先增大后减小,在8 wt%左右达最大值,BSA截留率随PVP浓度增加而单调增加;同质增强型中空纤维膜界面结合程度优于异质增强型.     

双凝胶剂中第一凝胶剂对聚砜中空纤维膜结构的影响

采用双凝胶浴法研究了第一凝胶剂(水、甘油、乙醇、丙酮和正己烷)对聚砜中空纤维膜近外表面处结构的影响。结果表明,第一凝胶剂的延迟时间越长,所制得的膜的近外表面处越疏松,铸膜液溶剂与第一凝胶剂之间溶解度参数差值(△δm)越大,制得的皮层结构越致密;第一凝胶剂瞬时分相时,易产生大孔结构,但当第一凝胶剂为非水溶性的正己烷时,尽管第一凝胶剂延迟分相而第二凝胶剂瞬时分相也产生大孔膜结构。     

THE INFLUENCE OF PEG MOLECULAR WEIGHT ON MORPHOLOGIES AND PROPERTIES OF PVDF ASYMMETRIC MEMBRANES

The preparation and properties of asymmetric poly(vinyldiene fluoride)(PVDF)membranes are described in this study.Membranes were prepared from a casting solution of PVDF,N,N-dimethylacetamide(DMAc)solvent and water- soluble poly(ethylene glycol)(PEG)additives by immersing them in water as coagulant medium.Experiments showed that when PEG molecular weight increased,the changes in the resultant membranes' morphologies and properties showed a transition point at PEG6000.This indicated that PEG with a relati...     

四甲基氢氧化铵改性聚偏氟乙烯一步接枝聚苯乙烯磺酸油水分离膜的制备及性能

利用四甲基氢氧化铵(TMAH)聚偏氟乙烯(PVDF)进行改性,以过氧化苯甲酰(BPO)为引发剂,将苯乙烯磺酸(SSA)接枝到改性的PVDF骨架上,制得聚偏氟乙烯接枝聚苯乙烯磺酸(PSSA-g-PVDF)油水分离膜。 研究了TMAH质量分数对PSSA的接枝率和油水分离膜性能的影响,同时采用傅立叶变换红外光谱(FTIR)、扫描电子显微镜(SEM)和视频光学接触角测量仪测试了膜的结构和表面接触角。 结果表明,TMAH使PVDF脱去部分氟化氢(HF)产生碳碳双键,硫元素均匀地分布在分离膜中。 PSSA的接枝率随着TMAH的质量分数增加而升高,分离膜的水通量随接枝率的升高先增加后降低。 当TMAH质量分数为20%,分离膜的接触角在30 s内降低到37.2°,接枝率和水通量分别为22.1%、643.3 L/(m·h),截留率和水通量恢复率分别达到90.6%和93.7%,衰减率为7.1%。 循环测试显示膜的水通量恢复率和油水通量恢复率均在90%以上。     

PVDF亲水复合膜的制备及表征

聚偏氟乙烯(PVDF)膜材料存在强疏水性的缺陷,亲水化改性是解决该问题的主要途径。以PVDF为基膜材料、聚乙烯醇(PVA)为共混材料、N,N-二甲基乙酰胺(DMAc)为溶剂,采用相转化法制备PVDF/PVA复合膜。考察了复合膜的PVDF/PVA共混比、固含量、低分子化合物添加剂、聚合物添加剂等非溶剂添加剂对复合膜接触角的影响。结果表明,当PVDF/PVA共混比为7/3,固含量为13%时,制备的复合膜接触角为22.92°;当添加剂为无水氯化锂、纳米二氧化硅、聚乙烯吡咯烷酮(PVP)时,复合膜接触角分别从53.12°、30.51°和41.89°都降低到了0°,亲水性提高,其中纳米二氧化硅作为添加剂时复合膜亲水性最好;当添加剂为丙三醇、PMMA、PEG时,复合膜接触角都增大,亲水性变差。     

新型微球载体材料——PACA-co-PEG的性能

聚氰基丙烯酸烷基酯;药物载体;生物降解性     

Porous membranes modified by hyperbranched polymers: I. Preparation and characterization of PVDF membrane using hyperbranched polyglycerol as additive

Porous membranes were prepared via phase inversion process from casting solution composed of poly(vinylidene fluoride) (PVDF), N,N-dimethylacetamide (DMAc), and hyperbranched polyglycerol (HPG). The membranes were characterized in terms of surface and bulk chemical compositions, morphology, water contact angle, porosity, and water flux. The effects of HPG content on membrane structures and properties were investigated. The effect of HPG addition on the hydrophilicity was discussed as well when the compositions of coagulation bath were changed. To better understand the special effects of HPG on the structures and properties of the membranes, PVDF membranes prepared using HPG as the additive were compared with those prepared using polyethylene glycol (PEG) as the additive.     

A FACILE APPROAC0H FOR THE SURFACE MODIFICATION OF POLY(VINYLIDENE FLUORIDE)MEMBRANE VIA SURFACE-INITIATED ATOM TRANSFER RADICAL POLYMERIZATION

A novel approach for the surface modification of poly(vinylidene fluoride)(PVDF)membrane was successfully realized through alkaline treatment,UV-induced bromine addition,and followed by surface-initiated atom transfer radical polymerization(ATRP)of methyl methacrylate(MMA).Chemical changes on the PVDF membrane before and after modification were analyzed with attenuated total reflectance Fourier transform infrared spectroscopy(AIR/Fr-IR)and X-ray photoelectron spectroscopy(XPS).Primary kinetic study revealed that the chain growth of poly(methyl methacrylate)(PMMA)from the PVDF surface is consistent with a"controlled"process.     

Effect of poly(ethylene glycol) 200 on the formation of a polyetherimide asymmetric membrane and its performance in aqueous solvent mixture permeation

To investigate the effect of poly(ethylene glycol) (PEG) 200 on membrane performance, asymmetric polyetherimide (PEI) membranes with a small pore size were prepared by dry/wet-phase inversion from the casting solution containing N-methyl-2-pyrrolidone as a solvent and poly(ethylene glycol) 200 as an additive. Our experiment revealed that the addition of PEG 200 has an influence on the casting solution properties, permeation properties, and resulting membrane structures. Moreover, a drying process also affects the formation of a dense skin layer. Increasing the amount of PEG 200 drastically improved the solute rejection rate. The drying process improved the rejection rate. We also observed the effect of the mixed solvent (water/ethanol) on permeation through the membranes with various pore sizes. In the case of the membrane with a dense skin layer, the solvent permeation showed relationships with solution viscosity, surface tension, and membrane-solvent interaction.     

Surface Interactions and Fouling Properties of Micrococcus luteus with Microfiltration Membranes

This study was conducted to investigate microbial adhesion of Micrococcus luteus to polypropylene (PP) and polyvinylidene fluoride (PVDF) membranes in relation to the variation of the interfacial energies in the membrane-bacteria systems, for revealing effects of short-range surface interactions on filtration behavior. Both the membranes and M. luteus showed typical strong electron donors and hydrophilic properties. The AB component was dominant in the interfacial energies of the two membrane-bacteria systems. M. luteus presented larger negative U(mlb)(XDLVO) to the PP membrane than to the PVDF membrane. The adhesion experiments also proved that M. luteus had higher adhesion percentage to the PP membrane. This study demonstrated that the adhesion potentials of M. luteus to the PP and PVDF membranes might be explained in terms of bacterium, membrane, and intervening medium surface properties, which are mainly determined by the interfacial energies in the systems according to the XDLVO theory.     

聚偏氟乙烯膜的改性研究进展

主要介绍了聚偏氟乙烯(PVDF)膜在近年来改性方法的最新研究进展,从辐照改性、等离子体改性、共混改性和化学改性等几方面进行了详细介绍,简要介绍了PVDF膜作为离子交换膜的一些最新应用.