Self-aggregation and antimicrobial activity of imidazolium and pyridinium based ionic liquids in aqueous solution

Adsorbed cetyldimethylbenzylammonium chloride (CDBACl) or cetyltrimethylammonium bromide (CTAB) on mercury is used as template for the adsorption of CTAB, CDBACl, or their equimolar mixture at 20 °C. Adsorptive stripping voltammetry with the two step procedure is used. The results are compared with previously published results on the adsorption of CTAB and CDBACl on mercury and then transferred in base electrolyte. A surfactant is preadsorbed. The adsorption of the second does not remove away from the mercury the first one, as evidenced by the capacitance measurements and the repeated scans. The surfactants were maintained close to each other and in the vicinity of the electrode by the applied electric field. In all cases studied, there was a decrease in the capacitance in the potential range -0.8 to -1 V to very low capacitance values forming condensed film. Mixed films and synergy effects were observed. The already adsorbed CTAB on mercury did not permit the desorption-reorientation peaks of CDBACl. Shifts of the capacitance peaks were observed to more positive potentials and were attributed to the occurrence of a slow change in the organization of the monolayer. The electrical state of the preadsorbed surfactant would be of critical importance in the formation of the various structures. The results suggested that the ordering and arrangement of molecules could be controlled by appropriate selection of templates.     

Adsorption of cetyltrimethylammonium bromide and cetyldimethylbenzylammonium chloride on a hanging mercury electrode studied by adsorptive transfer stripping voltammetry

The adsorption of cetyltrimethylammonium bromide (CTAB) and cetyldimethylbenzylammonium chloride (CDBACl) on a hanging mercury electrode is studied using adsorptive transfer stripping voltammetry. The surfactants are adsorbed on mercury and are then transferred in KBr or KCl under various conditions, including temperatures from 1 to 40°C, open or closed circuits with different initial potentials, and repeated scans, etc. The results are compared with previously published results on the adsorption of CTAB or CDBACl on mercury, where condensed films were formed and are quite different than those obtained by adsorptive stripping voltammetry. In this case, an absence of condensed film is observed for CTAB. A condensed film with low capacitance value is formed in the case of CDBACl after transfer at low temperatures, or after repeated scans, resulting in reorientation of the molecules to more compact states. Capacity time curves at the potentials where the film is formed show in a few cases a nucleation and growth mechanism, with induction time and studied by the Avrami formulation, while an observed increase of the capacitance with time is attributed to the formation of hemimicelles. The results also indicate the importance of interactions between the hydrophobic chains.     

The adsorption and condensed film formation of cetyltrimethylammonium bromide at the mercury/electrolyte interface

The adsorption of cetyltrimethyammonium bromide (CTAB) on a hanging mercury electrode is studied in various electrolyte systems and temperatures. A condensed film is formed at negative potentials and at room temperature only in the presence of KBr. The decrease of the temperature favors the formation of the condensed film. Hysterisis phenomena are observed during the potential scans at both directions. Capacity time curves at the potentials where the film is formed show a nucleation and growth mechanism, with induction time depending on potential, which has been investigated using Avrami formulation and has been explained as a progressive one-dimensional nucleation with constant growth rate. The nucleation rate increases while moving toward more negative potentials. A linear decrease of the capacitance with time was observed in some cases independent of the measuring potential in a relative large potential range. The different types of micelles can affect the adsorption of CTAB on mercury. An unusual capacitance transient observed at a very narrow negative potential range is attributed to the formation of hemicylinders. The condensed film in the presence of the other electrolytes is observed only at high concentrations (1 M) and very low temperatures (5 degrees C).     

On the adsorption and condensed film formation of dodecyl-, tetradecyl-, hexadecyl-, and octadecyltrimethylammonium bromides at the mercury/electrolyte interface

The adsorption and condensed film formation of dodecyl (DTAB)-, tetradecyl (TTAB)-, hexadecyl (CTAB)-, and octadecyl (OTAB)-trimethylammonium bromides on the hanging mercury electrode is studied in KBr as supporting electrolyte, at various temperatures from 5 to 45 degrees C. A condensed film is formed at negative potentials and at room temperature only in the presence of CTAB. The decrease of the temperature favors the formation of the condensed film. A transition temperature is observed for the film formation. Capacity-time curves at the potentials where the film is formed show a nucleation and growth mechanism, with induction time depending not only on the final potential but also on the initial potential range, although it is in the desorption region. In this temperature range no film is observed for DTAB and TTAB. However, the film is observed for OTAB, but only at higher temperatures, and is more easily formed with increasing temperature. The film is formed in a certain potential region and the nucleation rate increases while moving toward more negative potentials. Hysteresis phenomena are observed during changes of scan direction. The capacity vs time curves for OTAB, where condensed film is formed, are treated using an Avrami plot formulation and have been explained as progressive one-dimensional nucleation with a decrease of the nucleation rate during the overall film formation. The results show a marked effect of the chain length of the alkyl chain on the film formation.     

Effect of the deaeration on the adsorption of some cationic surfactants at the mercury/electrolyte solution interface

The effect of the deaeration on the adsorption of three cationic surfactants cetyldimethylbenzylammonium chloride (CDBACl), cetyltrimethylammonium bromide (CTAB) and octadecyltrimethylammonium bromide (OTAB) at the mercury/electrolyte solution interface is studied. The deaeration is studied using either nitrogen or helium and the effect of deaeration process and time is also studied. In all cases an effect of the deaeration time is found which is mainly observed at potentials where a condensed film is formed. Capacity-time curves at the potentials where the film is formed show a nucleation and growth mechanism with induction time that depends on the deaeration time. The deaeration slows down the kinetics of the film formation but does not change the equilibrium capacitance value of the film. The decrease of the dissolved gas from the water that perturbs its structure is perhaps the main reason for the behaviour observed during the adsorption of these surfactants.     

On the adsorption of cetyldimethylbenzylammonium chloride at the mercury/electrolyte solution interface

The adsorption of cetyldimethylbenzylammonium chloride (CDBACl) on the hanging mercury electrode is studied in various supporting electrolytes at various temperatures from 1 to 50 degrees C. A condensed film with low capacitance is formed at negative potentials at transition temperatures below approximately 40 degrees C. The decrease of the temperature favors the film formation, and increases the width of the capacitance pit, while its value remains practically constant. Hysteresis phenomena are also observed during different scan directions. Capacitance-time curves at the potentials where the film is formed show in some cases a nucleation and growth mechanism with induction time and studied by the Avrami formulation. At high temperatures an increase of the capacitance with time is observed depending on the CDBACl concentration and slightly on the electrolyte used, and is attributed to the formation of hemimicelles. At high negative potentials a second narrow region with lower capacitance values is observed. This is easily observed at very high temperatures, while it is absent at lower temperatures. It depends upon the concentration of CDBACl and the electrolyte used. The results are different from those obtained for the adsorption of cetyltrimethylammonium bromide on mercury, indicating the importance of interaction between the hydrophobic chains.     

Adsorption of cationic surfactants on covered hanging mercury drop electrode surface of variable area

Cetyldimethylbenzylammonium chloride (CDBACl) or cetyltrimethylammonium bromide (CTAB) is preadsorbed on mercury and used as substrate. The adsorptive stripping voltammetry with the two-step procedure is used. The mercury droplet with the preadsorbed surfactant is expanded in aqueous solutions of KCl, KBr, CTAB, CDBACl, or cetylethyldimethylammonium bromide (CEDAB). The surface area was increased from 0.0022cm(2) up to 0.0571cm(2). The surfactant molecules are maintained close to each other and in the vicinity of the electrode by the applied electric field. The expanding of the droplets resulted in a reorientation of the adsorbed molecules depending on the surfactant surface concentration. In some cases, condensed films were observed. Differences were noticed in the adsorption and desorption potential region. A linear increase in the capacitance current with the surface area was found in all cases up to a maximum increase in the surface area. Partly disorganized films were also observed. In some cases, defects were noticed during expansion. In one case, fractal structure was observed.     

On the adsorption and condensed film formation of binary mixtures of dodecyl-, tetradecyl-, hexadecyl-, and octadecyl-trimethylammonium bromides at the mercury–electrolyte interface

The adsorption and condensed film formation on mercury at the negative potential region for binary mixtures of dodecyltrimethylammonium bromide (DTAB), tetradecyltrimethylammonium bromide (TTAB), cetyltrimethylammonium bromide (CTAB), octadecyltrimethylammonium bromide (OTAB) is studied in KBr at various temperatures from 5 to 45 °C. The formation of the CTAB condensed film is hindered with the addition of DTAB and TTAB. There are interactions between unlike hydrophobic chains. The strong interactions between the CTAB molecules do not take place when DTAB or TTAB is present above a certain concentration. This hindering is more pronounced in the case of TTAB compared to the same DTAB concentration, i.e. the increase of the chain length hinders the film formation. The initially adsorbed molecules play a templating role in the kinetics of the film formation and in the self-assembling of the molecules. The initial induction time strongly depends on the temperature. The less surface active CTAB can hinder the OTAB film formation in binary mixtures. Also, increased interaction between OTAB and CTAB can be observed, indicating synergy effects in the film formation in some cases. The temperature range that the film is formed can be changed using mixtures of surfactants. Thus, the development of the film can become impossible, more difficult or even easier. Hysteresis phenomena are observed. The capacity versus time curves in the case that condensed film is formed are treated with the Avrami plot formulation, giving values between 1.5 and 2 indicating a progressive one dimensional nucleation with constant growth rate or a decrease of the nucleation rate during the overall film formation. There is generally a marked effect of the chain length of the alkyl chain on the film formation.     

Determination of molybdenum in the presence of 2-(2-benzothiazolylazo)-p-cresol by catalytic-adsorptive stripping voltammetry

The adsorptive collection of the molybdenum (VI) complexed with 2-(2-benzothiazolylazo)-p-cresol (BTAC) coupled with the catalytic current of the adsorbed complex at a static mercury drop electrode yields an ultrasensitive voltammetric procedure for the determination of molybdenum. Optimal experimental conditions were: a stirred acetate buffer 0.2 M (pH 3.5) as supporting electrolyte, a BTAC concentration of 1.0 x 10(-6) M as ligand, and a concentration of 0.1 M potassium nitrate as the oxidizing agent. In addition, a preconcentration potential of -0.080 V vs Ag/AgCl (3 M KCl), equilibration time of 15 s, a frequency of 30 Hz, a scan increment of 2 mV, a pulse amplitude of 0.050 mV, and a drop area of 0.032 cm2 were used. The cyclic voltammogram was recorded using a staircase wave with a scan rate of 100 mV/s. The forward scan starts at the initial potential of -0.080 V and is reversed at -0.90 V. Using the catalytic current at approximately -0.55 V the response to the Mo(VI) was found to be linear over a concentration range of 1.0-10.0 microg/L. The limit of detection is as low as 6.2 x 10(-10) M with 4 min of preconcentration time. The possible interference of other trace ions was investigated. The merits of this procedure are demonstrated using of reference samples.     

On the formation kinetics of two-dimensional cytidine films

The kinetics of phase transitions of cytidine adsorbed on mercury are studied by chronoamperometry and capacitance measurements. Cytidine forms highly ordered two-dimensional adlayers in a broad range of pH. In acid solvent, only one kind of condensed layer is formed. In the alkaline solution, cytidine forms two different two-dimensional (2D) adlayers. The minimum capacitance value in adlayer II at pH 5 is 7.0 microF cm(-2) and, at pH 8.3, it is 5.1 microF cm(-2); in adlayer III, the minimum capacitance is 10.6 microF cm(-2). The formation of a physisorbed film of cytidine molecules adsorbed at the mercury surface proceeds by complex mechanisms. From j-t transients, it can be seen that the phase transformations from dilute adlayer Ia to condensed physisorbed film II is accompanied by the reorientation of cytidine molecules at the mercury surface (inverted current transient). The interfacial transformations of the cytidine film yield a sigmoidal C-t transient. This experimentally measured C-t transient were analysed by Avrami theorem. The rate of the transformations from dilute adlayer Ia to condensed film II of cytidine at pH 5 depends strongly on temperature but is only slightly affected by temperature at pH 8.3. The effect of pH and ionic composition of the supporting electrolyte on the rate of transformation of cytidine films was studied as well.     

Determination of mercury in table salt samples by on-line medium exchange anodic stripping voltammetry

A new method for the determination of traces of total mercury by using a gold film electrode in salt samples was developed. Table salts are known to contain mercury at ultra-trace level as well as a high quantity of chloride ions that cause severe disturbance during the stripping step when gold is used as the electrode material in voltammetric measurements. The interference of high chloride content in the determination of mercury was eliminated by reducing its concentration down to 3 x 10(-3) mol L(-1) level which is optimum for the determination by using on-line medium exchange procedure immediately after the deposition step. The deposition potential applied to the electrode was maintained at 0.2 V (vs. Ag/AgCl double junction electrode) while the cell content was sucked by a pump and replaced with fresh electrolyte simultaneously. The analyte loss resulted from the air contact of the electrode was prevented by this means. The mercury ions present in the salt samples were collected at +0.2 V for 60 s, the electrolyte was replaced by 0.1 mol L(-1) HClO4 and the potential was scanned, attaining a detection limit of 0.17 microg L(-1), with R.S.D. of 1.2% (S/N=3). The recovery of the method was 94.6%. The performance and accuracy of the method was compared with that of atomic fluorescence spectrometry (AFS). Consequently, this developed method can offer a wide range of application in saline samples.     

Effect of deaeration on the adsorption of a mixture of cetyltrimethylammonium bromide and cetyldimethylbenzylammonium chloride at the mercury/electrolyte solution interface

The effect of deaeration on the adsorption of a mixture of cetyltrimethylammonium bromide and cetyldimethylbenzylammonium chloride at the mercury/electrolyte interface solution is studied using capacitance measurements focusing mainly at very low temperatures. Isochronous capacitance vs potential curves reconstructed from capacitance time curves show that the deaeration depends on the type of inert gas used as well as the deaeration process. The deaeration changes mainly the kinetics of the change of the capacitance with time. In cases where a condensed film is formed, the equilibrium capacitance value does not change with deaeration, indicating that the organization of the surfactants at the interface is not connected with the deaeration. The effect is attributed to the removal of dissolved gases from water.     

On the time dependence of the formation of a condensed film in the adsorption of adenosine at the interface mercury/electrolyte

The formation of a condensed film in the adsorption of adenosine at the interface mercury/electrolyte was investigated by means of the differential capacity-time dependence combined with the potential-step method. A mathematical function is given which approximates the experimentally found time dependence of the film formation. This function can theoretically be derived with the assumption that the mechanism of the formation of the condensed film is similar to that of two-dimensional nucleation in the case of metal deposition. A possible molecular mechanism of film formation is discussed.     

Copper–mercury film electrode for cathodic stripping voltammetric determination of Se(IV)

The copper-mercury film electrode has been suggested for the determination of Se(IV) in a wide range of concentration from 1x10(-9) to 1x10(-6) mol L(-1)by square-wave cathodic stripping voltammetry. Insufficient reproducibility and sensitivity of the mercury film electrode have been overcome by using copper(II) ions during the plating procedure. Copper(II) has been found to be reduced and form a reproducible copper-mercury film on a glassy carbon electrode surface. The plating potential and time, the concentration of copper(II) and the concentration of the supporting electrolyte have been optimised. Microscopy has been used for a study of the morphology of the copper-mercury film. It has been found that it is the same as for the mercury one. The preconcentration step consists in electrodeposition of copper selenide on the copper-mercury film. The relative standard deviation is 4.3% for 1x10(-6) mol L(-1) of Se(IV). The limit of detection is 8x10(-10) mol L(-1) for 5 min of accumulation.     

滴汞电极2.5次微分电分析法测定天然水中痕量钛

天然水中钛的定量分析有分光光度法、极谱法、催化波法等方法。微分电分析法尚未见报导。本文得出了以0.02M苦杏仁酸-4%氯酸钾(pH=3)为底液时,钛在滴汞电极上2.5次微分电分析法催化波,峰形明晰、干扰少、线性范围为1×10^-10-1×10^-7g/ml钛。可直接用于天然水中痕量钛的测定。     

Investigations on adsorption potentiometry-part VIII. Determination of ultratrace copper in food by derivative adsorption chronopotentiometry

An electroanalytical method, based on derivative chronopotentiometry of the copper complex with 4-[(4-diethylamino-2-hydroxyphenyl) azo]-5-hydroxy-naphthalene-2,7-disulphonic acid (Beryllon III) accumulated on the surface of a hanging mercury drop electrode, for determining trace copper in food has been developed. The dependence of the peak height of reduction of the copper complex on the preconcentration time and preconcentration potential are discussed. Optimum experimental conditions include 0.01 M HOAc, 0.01M NaOAc, 1.0 x 10(-6) Beryllon III and a preconcentration potential of 0.10 V (vs. SCE). Under these conditions the detection limit and the linear range are 4 x 10(-11)M and 6 x 10(-11) -4 x 10(-7)M, respectively. The method was applied to samples of digested rice.     

Determination of low concentrations of the flotation reagent ethyl xanthate by sampled DC polarography and flow injection with amperometric detection

A polarographic DC(tast) method with the static mercury drop electrode, SMDE, was developed for determination of the flotation collector ethyl xanthate (EtX) in the concentration range from 1x10(-5) to 8x10(-5) M. The potentiality of the method was demonstrated by evaluating the capacity of powdered galena ore (PbS) to adsorb EtX in a titration-like procedure. Sulfide could be determined simultaneously with EtX because in NaOH electrolyte their anodic waves are well separated (E(1/2) congruent with-0.72 and -0.42 V versus Ag/AgCl, respectively). In addition, a new FIA method was developed by adapting a simple device to the tip of the glass capillary of a mercury electrode and doing amperometric detection at a fixed potential of -0.1 V, always in the DC(tast) mode. No oxygen removal was required. Reproducible results were obtained at a frequency of 72 injections per h, with automatic renewal of the SMDE every second. The calibration curve for freshly prepared EtX standards rendered a straight line from 5x10(-6) to 8x10(-5) M with correlation coefficient of 0.997, suitable for real applications in flotation processes and its effluents.     

Direct zinc determination in commercial sulphuric acid by dpasv. Comparison of rotating disc and stationary graphite electrodes

A striking gas technique employed made a direct Zn determination possible at extremely low pH in commercial acid solutions when a stationary impregnated graphite-based mercury film electrode was used. The original Zn(II) concentrations were determined quantitatively by differential pulse anodic stripping voltammetry on 0.5M and 1M sulphuric acid solutions by standard addition and were found to be 2 x 10(-8)M and 4.1 x 10(-8)M, respectively. The influence of mercury ion concentration, pulse amplitude, potential step and pulse repetition time on analytical data was studied and optimized. A rotating disc graphite electrode was also used as a working electrode and was found unreliable for this purpose as hydrogen bubbles were not removed effectively and blocked the working electrode surface.     

Cathodic adsorptive stripping voltammetry of nickel complexed with hydroxynaphthol blue at a static mercury drop electrode

A new method is described for the determination of Ni based on the cathodic adsorptive stripping of Ni(II) complexed with hydroxynaphthol blue (HNB) at a static mercury drop electrode. Optimal conditions were found to be: accumulation potential -0.50 V (vs. Ag/AgCl); final potential -1.10 V; accumulation time 50 sec; scan rate 200 mV/sec; linear scan mode; filter 0.1 sec; supporting electrolyte acetic acid/acetate (0.25M, pH = 6.0) and concentration of HNB 3.3 x 10(-5)M. The response of the system was found to be linear in a range of Ni concentrations from 25 ppb to the detection limit. The detection limit was found to be 1.7 nM (0.10 ppb) with 2 mins of accumulation time. The effect of various potential interferences (including a variety of cations, anions and organic surfactants) were also studied. With the exception of Co, at less than equimolar concentrations no significant interferences were observed. Al was found to interfere at high concentrations with respect to Ni, but Al concentrations up to 1000 ppb may be masked by sodium citrate or sodium fluoride. The utility of the method is demonstrated by the recovery of Ni in a doped sample of commercial mineral water.     

Determination of palladium(II) with alpha-(2-benzimidazolyl)-alpha',alpha'-(N-5-nitro-2-pyridylhydrazone)-toluene by adsorptive cathodic stripping voltammetry

The determination of palladium(II) complexed with alpha-(2-benzimidazolyl)-alpha',alpha'-(N-5-nitro-2-pyridylhydrazone)-Toluene (BINPHT) was investigated by adsorptive cathodic stripping voltammetry using hanging mercury drop electrode. Palladium(II) in the sample solution can be determined in BINPHT and ethylenediaminetetraacetic acid (EDTA). Accumulation is achieved by adsorption of Pd(II)-BINPHT complex on a hanging mercury drop electrode. Optimal conditions were found to be: supporting electrolyte; 0.01 M sodium acetate buffer at pH 5.0, accumulation potential; -590 mV versus Ag/AgCl, accumulation time; 180 s, scan rate; 50 mV s(-1), concentration of BINPHT; 2x10(-5) M. The linear range of Pd(II) was observed over the concentration range 20-100 ng ml(-1) The detection limit (S/N=3) is 2 ng ml(-1). A good reproductivity shows RSD of 2.0% (n=7). This procedure offers high selectivity with the presence of EDTA masking some metallic ions. River water sample spiking with palladium was determined.