Uncertainty of determination of palladium in road dust sample by inductively coupled plasma mass spectrometry

The determination of palladium in a road dust sample taken close to the highway (w _Pd=450 ng g⁻¹) was carried out by the ICP-MS method after sample decomposition by aqua-regia. Analyses were evaluated by two methods: external calibration accompanied with mathematical correction of spectral interferences (EC) and isotope dilution measurement after separation of Pd by extraction to dibutyl sulfide solution (ID). In both cases, the uncertainties and accuracy of results were investigated. Although in the case of ideally homogeneous sample the repeatability of EC results (11 ng g⁻¹ Pd) was somewhat lower than those of ID results (16 ng g⁻¹ Pd), the uncertainties of results of both techniques were almost the same and they reached the level of 19 ng g⁻¹ Pd. The main uncertainty source of the EC method is represented by the correction of spectral interferences. In case of real non-homogeneous sample, the main uncertainty component represents the soil sampling. The uncertainty of results (approx. 75 ng g⁻¹ Pd) only slightly exceeded the repeatability (approx. 70 ng g⁻¹ Pd). The accuracy of results was proven by analyses of CRM TDB–1 Diabas Rock (in case of ID) and by the standard addition method (in case of EC).     

电感耦合等离子体质谱法测定烟酰胺药物元素杂质

建立了烟酰胺药物中30种元素杂质的ICP-MS分析方法,并根据USP< 233>进行了验证,在优化的实验条件下,本方法的检出限在4.0×10-4～0.4μg/L之间,加标回收率在86.3％～116.0％之间,与ICP-OES检测结果基本一致.用所建立方法对烟酰胺以及稳定性样品进行了元素杂质检测,根据样品制备工艺初步判断元素杂质的来源.     

电感耦合等离子体质谱法测定烟酰胺药物元素杂质

建立了烟酰胺药物中30种元素杂质的ICP-MS分析方法,并根据USP< 233>进行了验证,在优化的实验条件下,本方法的检出限在4.0×10-4～0.4μg/L之间,加标回收率在86.3％～116.0％之间,与ICP-OES检测结果基本一致.用所建立方法对烟酰胺以及稳定性样品进行了元素杂质检测,根据样品制备工艺初步判断元素杂质的来源.     

Radionuclide determination in environmental samples by inductively coupled plasma mass spectrometry

The determination of naturally occurring and anthropogenic radionuclides in the environment by inductively coupled plasma mass spectrometry has gained recognition over the last fifteen years, relative to radiometric techniques, as the result of improvement in instrumental performance, sample introduction equipment, and sample preparation. With the increase in instrumental sensitivity, it is now possible to measure ultratrace levels (fg range) of many radioisotopes, including those with half-lives between 1 and 1000 years, without requiring very complex sample pre-concentration schemes. However, the identification and quantification of radioisotopes in environmental matrices is still hampered by a variety of analytical issues such as spectral (both atomic and molecular ions) and non-spectral (matrix effect) interferences and instrumental limitations (e.g., abundance sensitivity).The scope of this review is to highlight recent analytical progress and issues associated with the determination of radionuclides by inductively coupled plasma mass spectrometry. The impact of interferences, instrumental limitations (e.g., degree of ionization, abundance sensitivity, detection limits) and low sample-to-plasma transfer efficiency on the measurement of radionuclides by inductively coupled plasma mass spectrometry will be described. Solutions that overcome these issues will be discussed, highlighting their pros and cons and assessing their impact on the measurement of environmental radioactivity. Among the solutions proposed, mass and chemical resolution through the use of sector-field instruments and chemical reactions/collisions in a pressurized cell, respectively, will be described. Other methods, such as unique sample introduction equipment (e.g., laser ablation, electrothermal vaporisation, high efficiency nebulization) and instrumental modifications/optimizations (e.g., instrumental vacuum, radiofrequency power, guard electrode) that improve sensitivity and performance will also be examined.     

Neptunium determination by inductively coupled plasma mass spectrometry (ICP-MS)

The determination of neptunium-237 (²³⁷Np) traditionally has been performed by alpha spectrometry or neutron activation analysis. These methods are labor intensive and require several days for completion. Inductively Coupled Plasma Mass Spectrometry (ICP-MS) is a possible alternative for²³⁷Np determinations. This paper describes the analytical method developed for samples that have significant levels of uranium present. The lower reporting limits achievable by ICP-MS are competitive with the counting methods, but the real advantage for this laboratory lies in the lower cost and faster turnaround time provided by ICP-MS.     

Direct determination of arsenic in fresh and saline waters by electrothermal vaporization inductively coupled plasma mass spectrometry

A method is described for the direct determination of arsenic in fresh and saline waters by electrothermal vaporization inductively coupled plasma mass spectrometry. Arsenic could be determined directly in waters containing up to 10 000 μg ml⁻¹ NaCl without interference from the formation of ⁷⁵ArCl⁺. For non-saline waters, arsenic was determined directly with the addition to both aqueous calibration standards and samples of 0.1 μg each of Pd and Mg to act as physical carriers. For the analysis of highly saline waters, the use of Pd and Mg chemical modifier served to thermally stabilize arsenic up to a temperature of 1000°C, while the separate addition of 8 mg of ammonium nitrate was used to remove chloride from the sample. This eliminated serious spectral interference on ⁷⁵As⁺ from ⁷⁵ArCl⁺. Although the ArCl⁺ spectral interference was completely eliminated, residual Na co-volatilized with As caused signal suppression, requiring the use of the method of standard additions for calibration. An absolute limit of detection limit for As of 0.069 pg was obtained corresponding to 6.9 pg ml⁻¹ in a 10 μl sample.     

Age determination of plutonium using inductively coupled plasma mass spectrometry

The age of plutonium is defined as the time since the last separation of the plutonium isotopes from their daughter nuclides. In this paper, a method for age determination based on analysis of ²⁴¹Pu/²⁴¹Am and ²⁴⁰Pu/²³⁶Pu using ICP-SFMS is described. Separation of Pu and Am was performed using a solid phase extraction procedure including UTEVA, TEVA, TRU and Ln-resins. The procedure provided separation factors adequate for this purpose. Age determinations were performed on two plutonium reference solutions from the Institute for Reference Materials and Measurements, IRMM081 (²³⁹Pu) and IRMM083 (²⁴⁰Pu), on sediment from the Marshall Islands (reference material IAEA367) and on soil from the Trinity test site (Trinitite). The measured ages based on the ²⁴¹Am/²⁴¹Pu ratio corresponded well with the time since the last parent-daughter separations of all the materials. The ages derived from the ²³⁶U/²⁴⁰Pu ratio were in agreement for the IRMM materials, but for IAEA367 the determination of ²³⁶U was interfered by tailing from ²³⁸U, and for Trinitite the determined age was biased due to formation of ²³⁶U in the detonation of the “Gadget”.     

Accurate determination of lead in wines by inductively coupled plasma mass spectrometry

Summary The capability of inductively coupled plasma mass spectrometry (ICP-MS) for Pb determinations in wine samples is studied. An evaluation is made of the signal behaviour in aqueous ethanolic medium. The effect of preliminary sample preparation on signal suppression or enhancement is investigated in conjunction with the ability of internal standardization to correct for it. As a result, an accurate and precise method of analysis is described in which the sample preparation is limited to a 10-fold dilution and external calibration is applied for quantitation. A detection limit of 0.2 g 1^–1 Pb in wine is achieved. The Pb content of ten different wines was found to range around 40 g 1^–1 with extreme values of 1.63 and 58.8 g 1^–1.     

Precise determination of boron in titanium by inductively coupled plasma mass spectrometry

A method was developed for the determination of boron in titanium by inductively coupled plasma mass spectrometry (ICP-MS). A commercially available PTFE sample introduction system, leading to the desired low detection limits for boron, was used. The method is suitable for the determination of boron concentrations down to about 1 μg g^?1 in the solid material. The influence of the internal standard on the precision was studied and beryllium was selected as the internal standard. For the titanium analysed (BCR reference material 090), the ICP-MS result agreed with those obtained using other techniques. Several bars of titanium reference material were supplied and a study of the homogeneity of boron in this material was made. Using analysis of variance on the results obtained for the different bars, the homogeneity of boron in the reference material could be estimated to be better than 2.1%.     

蒸气发生-电感耦合等离子体质谱法测定碘

建立了一种在线化学蒸气发生-电感耦合等离子体质谱测定碘的方法。利用碘负离子的还原性,采用氧化还原手段,将碘负离子氧化为碘单质;然后通过碘单质的易挥发特点,将碘蒸气直接导入等离子体。该方法可以提高传输效率,改善样品利用率,使检测灵敏度得到极大的提高。方法的检出限为0.22μg/L,样品加标回收率在87.4%~97.75%之间,RSD(n=11)在3%以内。实验中预先将正5价碘还原成碘负离子,然后加入氧化剂将碘负离子氧化成碘单质进行检测;对碘的形态化学蒸气发生法进行了尝试。     

电感耦合等离子体质谱法测定花生中34种元素

建立了微波消解-碰撞/反应池(ORS)电感耦合等离子体质谱仪(ICP-MS)同时测定花生中的Na、Mg、Ca、Fe、Se、Mo和稀土元素等34种元素的分析方法。样品经微波消解后,在线加入内标元素45Sc、72Ge、103Rh、115In和209Bi消除基体效应,应用碰撞反应池技术,以4.5 mL/min流速的氦气作为碰撞反应气,有效消除多原子离子产生的质谱干扰。各元素的检出限为0.0003～17.37ng/mL,相对标准偏差(RSD)低于2.9%;标准物质的测定值均在标准值范围内,结果令人满意。该方法可用于花生中多种元素的同时测定。     

Influence of sample pre-treatment on the determination of trace silver and cadmium in geological and environmental samples by quadrupole inductively coupled plasma mass spectrometry

The suitability of three different digestion procedures has been evaluated with regard to the quantitative determination of trace amounts of silver and cadmium in geological and environmental samples. Procedure A: extraction with aqua regia in an open vessel system; Procedure B: extraction with aqua regia in a closed pressurized vessel system; Procedure C: digestion with HF + HNO₃ in a closed pressurized vessel system. It was found that procedure A represented an effective way of extracting analytes from different types of geological samples while the effect of extracting interfering metals is low. Because it is interference-free, poses a low risk of contamination and is time-saving, sample treatment procedure A was preferred. For this digestion procedure, a series of Chinese geological reference materials was determined by ICP-MS, the results of which were found to be in reasonable agreement with the certified values.     

Lead determination in whole blood by laser ablation coupled with inductively coupled plasma mass spectrometry

This work describes a simple procedure for blood lead level determination. The proposed method requires little sample pretreatment and subsequent direct analysis of a dried blood spot on a filter membrane using laser ablation coupled with inductively coupled plasma mass spectrometry (LA-ICP-MS). In general, LA-ICP-MS studies are somewhat limited by the lack of matrix-matched standards for calibration purposes. Here we describe aqueous standard calibration and matrix-matched calibration methods. This method was validated by analysis of the reference materials. With the matrix-matched calibration method, the recovery ranged from 97.8% to 112.8%, while the aqueous standard calibration method ranged 90.4% to 122.4%. The lower detection limit was estimated as 0.1 ng mL⁻¹. The determination precision, expressed as the relative standard deviation (RSD), was not worse than 10% for all results. A sample throughput of approximately 5 min per sample made it possible to rapidly screen a large number of samples.     

Applications of inductively coupled plasma mass spectrometry and laser ablation inductively coupled plasma mass spectrometry in materials science

Inductively coupled plasma mass spectrometry (ICP-MS) and laser ablation ICP-MS (LA-ICP-MS) have been applied as the most important inorganic mass spectrometric techniques having multielemental capability for the characterization of solid samples in materials science. ICP-MS is used for the sensitive determination of trace and ultratrace elements in digested solutions of solid samples or of process chemicals (ultrapure water, acids and organic solutions) for the semiconductor industry with detection limits down to sub-picogram per liter levels. Whereas ICP-MS on solid samples (e.g. high-purity ceramics) sometimes requires time-consuming sample preparation for its application in materials science, and the risk of contamination is a serious drawback, a fast, direct determination of trace elements in solid materials without any sample preparation by LA-ICP-MS is possible. The detection limits for the direct analysis of solid samples by LA-ICP-MS have been determined for many elements down to the nanogram per gram range. A deterioration of detection limits was observed for elements where interferences with polyatomic ions occur. The inherent interference problem can often be solved by applying a double-focusing sector field mass spectrometer at higher mass resolution or by collision-induced reactions of polyatomic ions with a collision gas using an ICP-MS fitted with collision cell. The main problem of LA-ICP-MS is quantification if no suitable standard reference materials with a similar matrix composition are available. The calibration problem in LA-ICP-MS can be solved using on-line solution-based calibration, and different procedures, such as external calibration and standard addition, have been discussed with respect to their application in materials science. The application of isotope dilution in solution-based calibration for trace metal determination in small amounts of noble metals has been developed as a new calibration strategy. This review discusses new analytical developments and possible applications of ICP-MS and LA-ICP-MS for the quantitative determination of trace elements and in surface analysis for materials science.     

Methylmercury and inorganic mercury determination in blood by using liquid chromatography with inductively coupled plasma mass spectrometry and a fast sample preparation procedure

Despite the necessity to differentiate chemical species of mercury in clinical specimens, there are a limited number of methods for this purpose. Then, this paper describes a simple method for the determination of methylmercury and inorganic mercury in blood by using liquid chromatography with inductively coupled mass spectrometry (LC-ICP-MS) and a fast sample preparation procedure. Prior to analysis, blood (250 μL) is accurately weighed into 15-mL conical tubes. Then, an extractant solution containing mercaptoethanol, l-cysteine and HCl was added to the samples following sonication for 15 min. Quantitative mercury extraction was achieved with the proposed procedure. Separation of mercury species was accomplished in less than 5 min on a C18 reverse-phase column with a mobile phase containing 0.05% (v/v) mercaptoethanol, 0.4% (m/v) l-cysteine, 0.06 mol L⁻¹ ammonium acetate and 5% (v/v) methanol. The method detection limits were found to be 0.25 μg L⁻¹ and 0.1 μg L⁻¹ for inorganic mercury and methylmercury, respectively. Method accuracy is traceable to Standard Reference Material (SRM) 966 Toxic Metals in Bovine Blood from the National Institute of Standards and Technology (NIST). The proposed method was also applied to the speciation of mercury in blood samples collected from fish-eating communities and from rats exposed to thimerosal. With the proposed method there is a considerable reduction of the time of sample preparation prior to speciation of Hg by LC-ICP-MS. Finally, after the application of the proposed method, we demonstrated an interesting in vivo ethylmercury conversion to inorganic mercury.     

Direct sample insertion for inductively coupled plasma spectrometry

Direct sample insertion (DSI) is an alternative sample introduction technique for inductively coupled plasma spectrometry whereby the sample, either liquid or solid, is placed onto or into a sample carrying probe which is inserted directly into the plasma. This review provides an overview of the DSI technique including instrumentation, operating parameters, system response, analytical figures of merit and applications.     

Capillary electrophoresis inductively coupled plasma mass spectrometry

Chemical speciation (extraction of elemental information and identification of molecular environment for an analyte in a complex sample) has been a long sought after goal for analytical chemists. Recently, because of successful developments in more sensitive element-specific detectors and gentle separation schemes, which preserve the true chemical information in a real sample, routine speciation experiments are becoming a common occurrence in the scientific literature. For many reasons, the combination of capillary electrophoresis (for separation of different chemical species) with inductively coupled plasma mass spectrometry (for element and isotope specific detection) has emerged as the method of choice for these analyses. In this article the basic principles of capillary electrophoresis inductively coupled plasma mass spectrometry are discussed. Design consideration for instrument interface, anticipated difficulties with speciation experiments and applications for specific matrices and analytes are also presented in this article.     

Evaluation of different sample introduction approaches for the determination of boron in unalloyed steels by inductively coupled plasma mass spectrometry

An extended study of different sampling introduction approaches using inductively coupled plasma mass spectrometry (ICP-MS) is presented for the determination of boron in steel samples. The following systems for sample introduction were applied: direct sample solution nebulization by continuous nebulization (CN) using a cross-flow nebulizer and with flow injection (FI), applied to 0.1% (m/v) and 0.5% (m/v) sample solutions, respectively; FI after iron matrix extraction, using acetylacetone–chloroform, and isotopic dilution (ID) analysis as the calibration method; FI with on-line electrolytic matrix separation; and spark ablation (SA) and laser ablation (LA) as solid sampling techniques. External calibration with matrix-matching samples was used with CN, SA, and LA, and only acid solutions (without matrix matching) with FI methods. When FI was directly applied to a sample solution, the detection limit was of 0.15 μg g⁻¹, improving by a factor of 4 that was obtained from the CN measurements. Isotopic dilution analysis, after matrix removal by solvent extraction, made it possible to analyse boron with a detection limit of 0.02 μg g⁻¹ and, with the on-line electrolytic process, the detection limit was of 0.05 μg g⁻¹. The precision for concentrations above 10 times the detection limit was better than 2% for CN, as well as for FI methods. Spark and laser ablation sampling systems, avoiding digestion and sample preparation procedures, provided detection limits at the μg g⁻¹ levels, with RSD values better than 6% in both cases. Certified Reference Materials with B contents in the range 0.5–118 μg g⁻¹ were used for validation, finding a good agreement between certified and calculated values.