低相对分子质量苯乙烯-马来酸酐交替共聚物的合成

将引发剂偶氮二异丁腈(AIBN)、共聚单体苯乙烯(St)和马来酸酐(MA)溶解于甲苯中,采用沉淀聚合法合成苯乙烯-马来酸酐共聚物(SMA).分别研究了反应温度、引发剂用量、反应时间、单体配比和单体浓度对聚合物得率和酸酐含量的影响.采用正交实验确定最优反应条件为:单体浓度20%,单体物质的量比为1∶1,引发剂用量为0.60%,反应温度为86℃,反应时间2h,产物得率为86.86%,酸酐含量为50.28%.并利用傅里叶变换红外光谱(FTIR)、核磁共振碳谱(~(13)C NMR)、凝胶渗透色谱(GPC)和热分析法分别研究聚合物的分子结构、相对分子质量及相对分子质量分布和热稳定性.结果表明产物是苯乙烯-马来酸酐交替共聚物,相对分子质量分布较窄,具有良好的热稳定性.     

对-氯甲基苯乙烯共聚物引发合成接枝共聚物

接枝共聚物含有性质差别很大的主链和支链,具有许多特殊的性质,因而一直是人们感兴趣的研究课题之一^[1～5].原子转移自由基聚合(ATRP)^[6,7]的问世,为接枝共聚物的合成提供了一条新的途径.本文用对-氯甲基苯乙烯和其它乙烯基单体自由基共聚.     

磺化苯乙烯-马来酸酐共聚物

磺化苯乙烯-马来酸酐共聚物是由苯乙烯-马来酸酐共聚物直接磺化并中和成钠盐制备。由于它分子中含有很多磺酸及羧酸负离子,因此,是一很好的阴离子聚电解质,被广泛用于泥浆稀释剂、水泥添加剂和皮革鞣剂等。     

马来酸酐和苯乙烯的可逆加成-断链链转移聚合及新型嵌段共聚物的合成

马来酸酐和苯乙烯是被广为研究的一对电荷转移复合物 (Ｃｈａｒｇｅｔｒａｎｓｆｅｒｃｏｍｐｌｅｘ,简称ＣＴＣ) ,而且能通过通常的自由基聚合发生交替共聚[1] .所得的聚合物由于酸酐基团的存在 ,很易进行大分子改性得到具有某些特殊功能的高分子 .不过 ,所得共聚物的分子量难以控制且分子量分布也较宽 .近年来发展起来的“活性” 可控自由基聚合越来越为人们所关注 ,因为采用这种方法不仅可对聚合物的分子量进行设计 ,同时分子量分布也较窄 ,也不需要活性离子型聚合那样严格的聚合条件 .关于烯类单体的活性自由基聚合迄今主要有氮氧自由基…     

稀土催化异戊二烯—马来酸酐交替共聚

首次用 Nd( naph) 3 -Al Et3 催化体系合成异戊二烯 -马来酸酐交替共聚物 .实验结果表明 ,共聚反应适宜条件为 :[M]总 =2 .6mol/L( [Ip]/[MAn]=1 ) ,n( Al) /n( Nd) =1 0 ,[Nd]=5× 1 0 -3 mol/L,甲苯 /二氧六环混合溶剂 (体积比为 2 /5) ,于 5℃聚合 2 h.共聚物收率达到 70 % .用元素分析、 IR和 13 C NMR对共聚物进行表征 ,所得共聚物为交替结构     

支化型交替聚(苯乙烯-alt-马来酸酐)自组装胶束的制备及其乳化性能

利用支化型交替聚(苯乙烯-alt-马来酸酐)(BPSMA)在选择性溶剂DMF-H_2O中自组装制备球形胶束,以该胶束作为新型颗粒乳化剂稳定油-水体系,探讨胶束浓度和pH对BPSMA胶束乳化性能的影响。用紫外分光光度计(UV-Vis)追踪了聚合物溶液自组装过程;粒径及Zeta电位分析仪和透射电子显微镜(TEM)表征了BPSMA胶束的基本性质;利用光学显微镜分析了乳液性质,扫描电子显微镜(SEM)观察了胶束在固化后的油滴表面的形貌。结果表明:BPSMA胶束具有优异的乳化效率,在极低的质量浓度下(0.25~1.00 mg/mL)亦可长期稳定乳液;BPSMA胶束所稳定的乳液具有明显的pH响应性,当pH≤6时,胶束呈球形颗粒状吸附并稳定于油水界面,当pH6时,胶束从油水界面脱离,乳液破乳;此外,BPSMA胶束作为颗粒乳化剂还具备良好的普适性,可以长效稳定碳酸二辛脂、辛酸丙基庚酯、硅油、棕榈酸异辛酯和润肤油脂等。     

壳聚糖-O-聚(聚乙二醇甲醚甲基丙烯酸酯)接枝共聚物的ATRP合成及其自组装研究

以十二烷基硫酸钠-壳聚糖复合物(SCC)为起始物,将溴代异丁酸偶联到SCC的羟基上,得到溴代SCC(Br-SCC).以Br-SCC作为大分子引发剂,溴化亚铜、二联吡啶为催化剂,引发聚乙二醇单甲醚甲基丙烯酸酯(MPEGMA)原子转移自由基聚合,得到SCC-O-PMPEGMA;SCC-O-PMPEGMA中十二烷基硫酸钠(SDS)用Tris-2-甲基-2-氨基-1,3-丙二醇(Tris)解复合脱除,最终制备得到壳聚糖-O-PMPEGMA(CS-O-PMPEGMA).用FTIR和1H-NMR对中间产物与CS-O-PMPEGMA进行了表征,结果表明SCC的溴化度可以通过改变溴代异丁酸/SCC的投料比调节,改变MPEGMA/Br-SCC的投料比则可调控PMPEGMA的聚合度.用动态光散射、zeta电位仪以及TEM等手段研究了CS-O-PMPEGMA与肝素钠的复合行为,结果表明随着肝素钠/壳聚糖结构单元摩尔比(X)增加,复合胶束的粒径增大、表面电位降低;当X超过2时,肝素钠与CS-O-PMPEGMA复合形成球形纳米颗粒,其水合半径约44nm,zeta电位为-8.9mV.合成得到的CS-O-PMPEGMA具有规整化学结构,能与聚阴离子复合形成球形胶束,很有希望在基因传递与肿瘤靶向等领域得到应用.     

苯乙烯-马来酸酐共聚物的核磁共振分析

利用^1H NMR、^13C NMR及DEPT(无畸变极化转移增强)核磁共振技术研究了苯乙烯-马来酸酐共聚物(SMA)的序列结构和组成，并比较了几种核磁共振实验技术对分析SMA结果的准确性；实验表明^1H NMR是分析组成的简单、快速而有效的方法，DEPT谱进行序列结构计算准确度较高。     

苯乙烯-马来酸酐共聚物中酸酐含量测定方法研究

苯乙烯-马来酸酐共聚物（SMA）分子结构中含有酸酐官能团,易于化学改性得到新型功能高分子,在生物以及化学方面均表现出优异特性,而酸酐含量是影响其性能的重要因素,因此必须准确分析共聚物中酸酐含量。本文首先对SMA水溶液进行pH值滴定,确定了SMA在pH值突跃范围内以一元羧基／一元羧酸钠的形式存在,利用微商法确定该范围内pH滴定终点,建立了一种简便、快速确定酸酐含量的pH值滴定方法,并经元素分析验证了该方法测定结果的准确性。     

酸性条件下两种马来酸-烯烃交替共聚物诱导细胞色素c的结构转换

在pH=2·9时,细胞色素c保持类天然的结构;和马来酸-烯烃交替共聚物作用后,细胞色素c的α-螺旋结构基本保持不变,但是三级结构被破坏.另一方面,在pH=2·1时,细胞色素c去折叠形成伸展的无规卷曲构象;马来酸-烯烃交替共聚物可以诱导酸变性的细胞色素c从无规卷曲构象转变为α-螺旋结构.在酸性溶液中,由于马来酸-异丁烯交替共聚物和细胞色素c之间更强的相互作用,其对蛋白质结构的影响大于马来酸-1-十四烯交替共聚物.相对于小分子,聚合物可以在低浓度条件下提供有利于蛋白质结构转换的微环境.     

Synthesis of densely grafted comblike copolymers

Densely grafted copolymers were synthesized using the “grafting from” approach via the combination of reversible addition‐fragment chain transfer polymerization (RAFT) and atom transfer radical polymerization (ATRP). First, a novel functional monomer, 2,3‐di(2‐bromoisobutyryloxy)ethyl acrylate (DBPPA), with two initiating groups for ATRP was synthesized. It was then polymerized via RAFT polymerization to give macroinitiators for ATRP with controlled molecular weights and narrow molecular weight distributions. Last, ATRP of styrene was carried out using poly(DBPPA)s as macroinitiators to prepare comblike poly(DBPPA)‐graft‐polystyrenes carrying double branches in each repeating unit of backbone via “grafting from” approach. Furthermore, poly(DBPPA)‐graft‐[polystyrene‐block‐poly(t‐BA)]s and their hydrolyzed products poly(DBPPA)‐graft‐[polystyrene‐block‐poly(acrylic acid)]s were also successfully prepared. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 362–372, 2008     

Linear nano-templates of styrene and maleic anhydride alternating copolymers

Poly(styrene-alt-maleic anhydride) (SMA) self-assembles in aqueous solution to form nanotube structures. These can be used as templates to linearly guide the growth of a secondary polymeric or inorganic material. Templates are made starting from a basic SMA solution, followed by slow pH decrease by dialysis against deionized water, until a 50% degree of protonation is reached. The nanotube structure is composed of multiple polymer chains, associating sideways by π-stacking to form the nanotube walls. The SMA templates were used to grow linear composites, which shows the applicability of the template properties and also confirms the nanotube association mechanism. Linear polymer composites were formed using this SMA template: pyrrole was polymerized, silver nitrate was reduced to silver and silver cyanide nanowires were grown.     

Polynucleotide analogues. VI. Synthesis and characterization of alternating copolymers of maleic anhydride and dihydropyran containing guanine derivatives

2-Amino-6-chloropurine was reacted with 2-(tosyloxymethyl)-2,3-dihydro-2H-pyran to give 2-(2-amino-6-chloropurin-9-ylmethyl)-2,3-dihydro-2H-pyran ( 3 ) and its N⁷-isomer ( 4 ), which were treated with 5% aqueous trimethylamine to result in 2-(guanin-9-ylmethyl)-2,3-dihydro-2H-pyran ( 5 ) and its N⁷-isomer ( 6 ), respectively. 2-(N²-Acetylguanin-9-yl-methyl)-3,4-dihydro-2H-pyran ( 7 ) and 2-(N²-acetylguanin-7-ylmethyl)-3,4-dihydro-2H-pyran ( 8 ), obtained by acetylation of compounds 5 and 6 , were copolymerized with maleic anhydride to give the alternating copolymers 9 and 10 , and they were hydrolyzed to result in poly[ {2-(guanin-9-ylmethyl)tetrahydropyran-5,6-diyl} {1,2-dicarboxyethylene}] ( 11 ) and poly[ {2-(guanin-7-ylmethyl)tetrahydropyran-5,6-diyl} {1,2-dicarboxyethylene}] ( 12 ), re-spectively. Polymer 11 showed hypochromicity whereas 12 exhibited hyperchromicity in aqueous solutions. Polymers 11 and 12 in aqueous solutions showed very strong excimer fluorescence with the maximum intensities at 432 and 446 nm, respectively, at room tem-perature. The two polymers showed polyelectrolyte effects, e.g., very high GPC molecular weights as well as reduced viscosities at low concentrations in water. Normal behavior was retained by addition of inorganic salts. Sodium salts of polymers 11 and 12 migrated to the anode by electrophoresis and both showed two bands. © 1995 John Wiley & Sons, Inc.     

Initiated chemical vapor deposition of alternating copolymers of styrene and maleic anhydride

Initiated chemical vapor deposition (iCVD) of alternating copolymer thin films has been achieved for the first time. Copolymerization is desirable for maleic anhydride (Ma) since this monomer does not homopolymerize to an appreciable extent. At conditions where the observed deposition rates for styrene (S) and Ma homopolymers were only 0 and 5.5 nm/min, respectively, combining the two monomers resulted in a much higher deposition rate of 75.4 nm/min. iCVD processes utilize low energy (<30 W) to generate peroxy radicals from initiator molecules while avoiding degradation of functional groups in the monomers. Indeed, full retention of the anhydride functionality from the Ma monomer and avoidance of undesirable side reactions was observed in iCVD of poly(styrene-alt-maleic anhydride) (PSMa) copolymer films. Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and 13C nuclear magnetic resonance (NMR) conclusively demonstrate that all of the copolymer films contain 50% styrene and 50% Ma (within experimental error), irrespective of gas feed ratios employed during the deposition. The 13C NMR signal in the 136-140 ppm region from the quaternary carbon in styrene and additional distortionless enhancement polarization transfer experiments confirmed that the copolymers are strictly alternating. Varying the gas feed ratio of Ma to styrene provided control over deposition rates and number-average molecular weights. Number-average molecular weights varied from 1380 to 4680 g/mol, and deposition rates varied from 6.3 to 75.4 nm/min.     

Itaconic anhydride based amphiphilic copolymers: Synthesis, characterization and stabilization of carboxyl functionalized, PEGylated nanoparticles

N-Vinyl-2-pyrrolidone (NVP) and itaconic anhydride (IA) copolymers were synthesized via radical polymerization. The synthesized copolymers were grafted with MPEG chains of different average molecular weights (350, 550, 750 Da). The grafted copolymers were used as surfactants in the synthesis of poly(ε-caprolactone) (PCL) nanoparticles in water by solvent evaporation technique. In order to further test the synthesized surfactants, the miniemulsion polymerization of vinyl acetate was performed. Two methods of obtaining miniemulsion were implied: a sonicator and a static mixer. The synthesized surfactants performed well in both type of experiments while in the case of static mixer nanoparticles with a lower polydispersity were obtained. Droplets with a mean diameter of 160 nm were obtained when using the sonicator while in the case of static mixer the mean diameter was 280 nm.     

Synthesis and metal complexation of dihydroxyphosphino‐functionalized crosslinked styrene/maleic anhydride copolymers

Crosslinked styrene (St)/maleic anhydride (MA) copolymers were synthesized, hydrolyzed with dicarboxylic acid, and converted to bear dihydroxyphosphino functionalities. The St–MA copolymers were prepared by azobisisobutyronitrile‐initiated polymerization in toluene at 90 °C in the presence of 2, 10, or 20% divinylbenzene crosslinker. The MA moiety was hydrolyzed into dicarboxylic acid to improve the hydrophilicity of the copolymers. The phenyl ring of St was phosphorylated with phosphorus trichloride in the presence of aluminum chloride and then hydrolyzed and oxidized with nitric acid at room temperature. The structures of the hydrolyzed and dihydroxyphosphino‐functionalized copolymers were confirmed by Fourier transform infrared spectroscopy and elemental analysis. The complexation behavior of these functionalized copolymers toward metal ions in 25 ppm aqueous solutions was observed over time periods of up to 7 h. The adsorption toward Pb(+2) was highest, followed by those of Cu(+2), Cr(+3), and Ni(+2). On the dihydroxyphosphino‐functionalized St–MA (20% divinylbenzene) copolymer, the adsorption of Pb(+2) showed a linear relationship with the concentrations and fit the Langmuir isotherm. The kinetics of Pb(+2) adsorption on this dihydroxyphosphino‐functionalized copolymer also fit the rate equation of the moving boundary model, t = [1 ? 3(1 ? X)^2/3 + 2(1 ? X)], where X is the fractional conversion. The metal‐ion adsorption kinetics of this copolymer appeared to be particle diffusion control, in which the moving boundary advanced from the surface toward the center. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 92–101, 2004     

Synthesis of methyl methacrylate,styrene, and isobutylene multiblock copolymers using atom transfer and cationic polymerization

ABCBA‐type pentablock copolymers of methyl methacrylate, styrene, and isobutylene (IB) were prepared by the cationic polymerization of IB in the presence of the α,ω‐dichloro‐PS‐b‐PMMA‐b‐PS triblock copolymer [where PS is polystyrene and PMMA is poly(methyl methacrylate)] as a macroinitiator in conjunction with diethylaluminum chloride (Et₂AlCl) as a coinitiator. The macroinitiator was prepared by a two‐step copper‐based atom transfer radical polymerization (ATRP). The reaction temperature, ?78 or ?25 °C, significantly affected the IB content in the resulting copolymers; a higher content was obtained at ?78 °C. The formation of the PIB‐b‐PS‐b‐PMMA‐b‐PS‐b‐PIB copolymers (where PIB is polyisobutylene), prepared at ?25 (20.3 mol % IB) or ?78 °C (61.3 mol % IB; rubbery material), with relatively narrow molecular weight distributions provided direct evidence of the presence of labile chlorine atoms at both ends of the macroinitiator capable of initiation of cationic polymerization of IB. One glass‐transition temperature (T_g), 104.5 °C, was observed for the aforementioned triblock copolymer, and the pentablock copolymer containing 61.3 mol % IB showed two well‐defined T_g's: ?73.0 °C for PIB and 95.6 °C for the PS–PMMA blocks. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3823–3830, 2005     

Amphiphilic maleic acid-containing alternating copolymers—1. Dissociation behavior and compositions

The dissociation of the two adjacent carboxylic acids in maleic acid-containing copolymers is expected to differ from those of poly(acrylic acid) and poly(methacrylic acid) where the acids are separated by two carbons on the backbone. In this work, we have employed potentiometric titration and NMR spectroscopy to characterize the dissociation behavior and chemical compositions of several water-soluble maleic acid-containing copolymers. A distinct two-step process corresponding to the dissociation of the two adjacent carboxylic acids is observed in aqueous CaCl₂ (0.02 N) solution for copolymers of maleic acid and isobutylene, diisobutylene, and styrene. Such a two-step ionization process is less recognizable, however, for the copolymers of maleic acid and linear alkenes ranging from n-hexene to n-octadecene. Nevertheless, the compositions of all copolymers, including the extent of neutralization and the ratio of the comonomer moieties, are estimated from the titration curves. The chemical composition derived from potentiometry and NMR spectroscopy for all copolymers are approximately 1 : 1 (maleic acid : comonomer). With the exception of the hydrophobically modified copolymer of isobutylene-maleic acid, no obvious conformational transition was observed over the whole range of ionization for these hydrophobic maleic acid-containing copolymers. This is related to the aggregated state of these copolymers in aqueous media. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3571–3583, 2004     

Synthesis and characterization of polymeric linseed oil grafted methyl methacrylate or styrene

Syntheses of wholly natural polymeric linseed oil (PLO) containing peroxide groups have been reported. Peroxidation, epoxidation and/or perepoxidation reactions of linseed oil, either under air or under oxygen flow at room temperature, resulted in polymeric peroxides, PLO-air and PLO-ofl, containing 1.3 and 3.5 wt.-% of peroxide, with molecular weights of 2 100 and 3 780 Da, respectively. PLO-air contained cross-linked film up to 46.1 wt.-% after a reaction time of 60 d, associated with a waxy, soluble part (PLO-air-s) that was isolated with chloroform extraction. PLO-ofl was obtained as a waxy, viscous liquid without any cross-linked part at the end of 24 d under visible irradiation and oxygen flow. Polymeric peroxides, PLO-air-s and PLO-ofl initiated the free radical polymerization of both methyl methacrylate (MMA) and styrene (S) to give PMMA-graft-PLO and PS-graft-PLO graft copolymers in high yields with Mw varying from 37 to 470 kDa. The polymers obtained were characterized by FT-IR, (1)H NMR, TGA, DSC and GPC techniques. Cross-linked polymers were also studied by means of swelling measurements. PMMA-graft-PLO graft copolymer film samples were also used in cell-culture studies. Fibroblast cells were well adhered and proliferated on the copolymer film surfaces, which is important in tissue engineering.     

Optically active alternating copolymers of maleic anhydride and alkylvinylethers

Maleic anhydride (MAn) was copolymerized in benzene solution at 60° using AIBN with some optically active alkylvinylethers (RVE) having an asymmetric carbon atom at the α, β, γ or δ position with respect to the oxygen atom [R = (S)-1-methylpropyl, (R)-1-methylbutyl, (S)-2-methylbutyl, (S)-3-methylpentyl, (S)-4-methylhexyl, (S)-1-methylheptyl and (S)-3,7-dimethyloctyl]. Chemical compositions and solubilities of the polymeric products as well as optical rotation properties and spectroscopic measurements (i.r. and NMR) confirmed the formation of copolymers with a predominantly alternating structure. Two Cotton effects of low but definite intensity attributable to $\text{n → π}{}^1$ electronic transitions of carbonyl groups of anhydride moieties were observed between 200 and 250 nm. Failure to achieve complete cleavage of chiral side chains does not enable us to attribute the induced optical activity of anhydride moieties either to the asymmetric carbon atom present in the side chain or to the tertiary chiral centres present in the main chain or both.