The propagation of Lamb waves in a plate bordered with layers of a liquid.

The influence of liquid layers on the propagation of Lamb waves in a plate of finite thickness is studied theoretically. The dispersion equations of Lamb waves in a plate bordered with layers of liquids are derived. Numerical solutions of the equations show that the phase velocity of Lamb waves changes with the thickness of the liquid layers. For the lowest antisymmetrical mode of very thin plates, the numerical results calculated from the dispersion equations are compared with those derived from the bending wave acoustic impedance approach. The limitation of the latter is discussed. Applications of Lamb waves pertinent to biosensing are also presented.     

超声Lamb波二次谐波发生效率分析与模式选择

在导波模式展开分析方法的基础上,提出激发效率参量来定量表征超声Lamb波积累二次谐波的发生效率。以P92钢板为例,理论计算得到了与频散曲线对应的理论激发效率参量分布图谱,从图谱中选择理论激发效率参量大小不同的两种基频Lamb波模式:纵波型S1模式和交点型A2/S2模式,分别测量这两种基频Lamb波模式在钢板中传播时产生的二次谐波信号。理论计算和实验测量结果表明,这两种基频Lamb波模式的理论和实验激发效率参量的比值基本一致,且激发效率参量较大的纵波型S1模式能激发出效率更高的二次谐波信号。研究结果表明激发效率参量可以有效的用于Lamb波二次谐波发生效率的表征及模式选择。      

非线性兰姆波在阶梯板中传播的有限元仿真

在非线性兰姆波检测中,累积二次谐波是重要的检测信号.该文利用有限元法仿真了非线性兰姆波在阶梯板中的产生和传播过程,通过二维离散傅里叶变换分析了兰姆波的传播模态和各个模态通过波导横截面的能流大小,给出了各个模态在阶梯板中的反射、透射系数,总结了其随阶梯板厚度的变化规律.研究发现,随着台阶增高,散射效应使得兰姆波更难入射波...     

Cumulative second-harmonic generation of Lamb waves propagating in a two-layered solid plate

The physical process of cumulative second-harmonic generation of Lamb waves propagating in a two-layered solid plate is presented by using the second-order perturbation and the technique of nonlinear reflection of acoustic waves at an interface. In general, the cumulative second-harmonic generation of a dispersive guided wave propagation does not occur. However, the present paper shows that the second-harmonic of Lamb wave propagation arising from the nonlinear interaction of the partial bulk acoustic waves and the restriction of the three boundaries of the solid plates does have a cumulative growth effect if some conditions are satisfied. Through boundary condition and initial condition of excitation, the analytical expression of cumulative second-harmonic of Lamb waves propagation is determined. Numerical results show the cumulative effect of Lamb waves on second-harmonic field patterns.     

Analysis of Second-Harmonic Generation of Low-Frequency Dilatational Lamb Waves in a Two-Layered Composite Plate

We analyze the effect of second-harmonic generation(SHG) of primary Lamb wave propagation in a two-layered composite plate, and then investigate the influence of interfacial properties on the said effect at low frequency. It is found that changes in the interfacial properties essentially affect the dispersion relation and then the maximum cumulative distance of the double-frequency Lamb wave generated. This will remarkably influence the efficiency of SHG. To overcome the complications arising from the inherent dispersion and multimode natures in analyzing the SHG effect of Lamb waves, the present work focuses on the analysis of the SHG effect of low-frequency dilatational Lamb wave propagation. Both the numerical analysis and finite element simulation indicate that the SHG effect of low-frequency dilatational Lamb wave propagation is found to be much more sensitive to changes in the interfacial properties than primary Lamb waves. The potential of using the SHG effect of low-frequency dilatational Lamb waves to characterize a minor change in the interfacial properties is analyzed.     

Microcrack localization using a collinear Lamb wave frequency-mixing technique in a thin plate

A novel Lamb wave frequency-mixing technique is proposed for locating microcracks in a thin plate,which does not require the resonance condition of Lamb wave mixing and can accurately locate the microcracks through only one-time sensing.Based on the bilinear stress-strain constitutive model,a two-dimensional finite element(FE)model is built to investigate the frequency-mixing response induced by the interaction between two primary Lamb waves and a microcrack.When two primary Lamb waves of A0 and S0 modes with different frequencies excited on the same side of the plate simultaneously impinge on the examined microcrack,under the modulation of the contact acoustic nonlinearity,the microcrack itself can be deemed as the secondary sound source and it will radiate the Lamb waves of new combined frequencies.Based on the time of flight of the generated A0 mode at difference frequency,an indicator named normalized amplitude index(NAI)is defined to directly locate the multi-microcracks in the given plate.It is found that the number and location of the microcracks can be intuitively visualized by using the NAI based frequency-mixing technique.It is also demonstrated that the proposed frequency mixing technique is a promising approach for the microcrack localization.     

两侧有固体层负载时板中Lamb波的传播

本文研究了薄板二面有固体导负载时板中Ｌａｍｂ波的传播，从弹性波理论出发并结合应的边界条件，导出板中Ｌａｍｂ波的色散方程，数值计算表示，不管作为自由状态时板中Ｌａｍｂ波相速（板厚取定时）是大于或小于外层固体的声表面波波速，板中对称及反对称模式的Ｌａｍｂ波相速都随着外层固体层厚度增加而变化并且渐近于外层固体的声表面波波速，数值计算又表明，对很薄的板，板中对称及反对称模式的相速均随负载板的厚度呈线性变化     

The propagation of coupled Lamb waves in multilayered arbitrary anisotropic composite laminates

Based on linear three-dimensional elasticity theory, the wave equations of coupled Lamb waves in multilayered arbitrary anisotropic composite laminates are derived using a Legendre orthogonal polynomial approach. The elastodynamic solution for the propagation of coupled Lamb waves in composite plates is also presented to determine the characteristics of coupled Lamb waves. To verify the applicability and validity of the method, two cases of bi-layered plates formed with isotropic components and anisotropic components, respectively, are primarily manipulated for comparison with earlier known results. Next, the dispersion curves, displacements and stress distributions of Lamb waves in multilayered anisotropic laminates are calculated. The effects of coupling and fiber orientation on the characteristics of the Lamb waves are illustrated. The potential usefulness of the fundamental modes of the coupled Lamb waves is discussed in detail.     

Lamb mode reflections at the end of a plate loaded by a viscoelastic material

This paper deals with a study of the conversion of a Lamb wave at the loaded edge of a plate. An experimental study is performed to know the interaction of surface waves with a viscoelastic material. A Lamb wave is generated by a wedge. At the end of the plate, this wave gives rise to several reflected waves. A first study makes it possible qualitatively to know the Lamb modes present in reflection. Secondly, conversion phenomena are studied to know if surface waves are sensitive to evolution in the time of the viscoelastic material structure. The selected material is a sol-gel containing silica.     

套管中模式波的响应特征

在固井质量评价中主要利用套管中模式波的幅度或衰减变化反映水泥的胶结状况,不同测井仪器在套管中激发的模式波的类型不同,研究套管中各模式波的传播特征和影响因素可充分挖掘测量数据的潜在应用价值。CBL和SBT等测井仪器在套管中主要激发拉伸波,类同于平板中的零阶对称Lamb波,水泥环封隔测井仪器的斜入射模式在套管中主要激发套管弯曲波,类同于平板中的零阶反对称Lamb波,垂直入射模式激发套管共振波,类同于平板中的高阶对称Lamb波。该文重点分析了这些模式波的衰减特征及其对微环的响应,套管弯曲波在套后耦合轻质水泥时对微环不敏感,但在套后耦合常规水泥或重水泥时,其衰减明显高于胶结良好的状况;拉伸波对微环的存在最为敏感;套管共振波对微环不敏感。     

Propagation of time-reversed Lamb waves in acrylic cylindrical tubes as cortical-bone-mimicking phantoms

The present study aims to investigate the propagation of time-reversed Lamb waves in acrylic cylindrical tubes as cortical-bone-mimicking phantoms. Time-reversed Lamb waves could be successfully launched in 6 acrylic tubes with wall thicknesses from 2 to 12 mm by using a modified time reversal method. The group velocities of the time-reversed Lamb waves in the acrylic tubes were measured by using the axial transmission technique. They decreased very slightly with increasing wall thickness, showing good agreement with the theoretical group velocity of the A0 Lamb wave in the acrylic plate. These results suggest that the time-reversed Lamb waves in the acrylic tubes would essentially behave as the A0 Lamb wave, consistent with the behavior of the slow guided wave in long cortical bones. It is expected that the application of the time-reversed Lamb waves in long bones would enhance clinical potential of ultrasonic technologies for the diagnosis of osteoporosis.     

Design of optimal configuration for generating A0 Lamb mode in a composite plate using piezoceramic transducers

This work concerned a technique for a health monitoring system based on the generation and sensing of Lamb waves in composite structures by thin surface-bonded piezoceramic transducers. The objective was to develop transducers that are adapted for the damage detection in orthotropic composites. The key problem with the investigated Lamb waves was to select a mode to be sensitive to the damage. A hybrid modeling technique was therefore used to conceive transducers that were adapted to achieve such a feature. This modeling technique enabled studying the influence of the transducer characteristics on the Lamb waves propagating in orthotropic plates. It was demonstrated that a Lamb mode could be generated dominantly to other modes by using a multi-element transducer. The effectiveness of this technique was successfully verified experimentally on composite plates. It was shown that the dominant Lamb mode, obtained by use of dual-element transducers, was an appropriate mode for successfully detecting a damage in composites.     

Characterization of surface properties of a solid plate using nonlinear Lamb wave approach

A nonlinear Lamb wave approach is presented for characterizing the surface properties of a solid plate. This characterization approach is useful for some practical situations where ultrasonic transducers cannot touch the surfaces to be inspected, e.g. the inside surfaces of sealed vessels. In this paper, the influences of changes in the surface properties of a solid plate on the effect of second-harmonic generation by Lamb wave propagation were analyzed. A surface coating with the different properties was used to simulate changes in the surface properties of a solid plate. When the areas and thicknesses of coatings on the surface of a given solid plate changed, the amplitude-frequency curves both of the fundamental waves and the second harmonics by Lamb wave propagation were measured under the condition that Lamb waves had a strong nonlinearity. It was found that changes in the surface properties might clearly affect the efficiency of second-harmonic generation by Lamb wave propagation. The Stress Wave Factors (SWFs) in acousto-ultrasonic technique were used for reference, and the definitions of the SWFs of Lamb waves were introduced. The preliminary experimental results showed that the second-harmonic SWF of Lamb wave propagation could effectively be used to characterize changes in the surface properties of the given solid plate.     

压电晶片传感器监测金属薄板的腐蚀

激励压电晶片传感器产生Lamb波并用于监测金属板材的腐蚀,由信号的相关系数表征腐蚀对在板中Lamb波传播特性的影响。实验结果表明在Lamb波模态中A₀模式受腐蚀影响大,适合用于监测金属的腐蚀。Lamb波通过腐蚀区域后由于频散以及信号幅度和相位的变化对采集的损伤信号与健康状态信号的相关系数有影响。在腐蚀区域直径一定的情况下,对应的相关系数并不随腐蚀深度的增加而单调递减;在腐蚀深度一定时,相关系数随腐蚀区域直径增加而单调递减。     

Second Harmonic Generation of Lamb Wave in Numerical Perspective

The influences of phase and group velocity matching on cumulative second harmonic generation of Lamb waves are investigated in numerical perspective.Finite element simulations of nonlinear Lamb wave propagation are performed for Lamb wave mode pairs with exact and approximate phase velocity matching,with and without group velocity matching,respectively.The evolution of time-domain second harmonic Lamb waves is analyzed with the propagation distance.The amplitudes of primary and second harmonic waves are calculated to characterize the acoustic nonlinearity.The results verify that phase velocity matching is necessary for generation of the cumulative second harmonic Lamb wave in numerical perspective,while group velocity matching is demonstrated to not be a necessary condition.     

铝板中Lamb波检测的实验研究

Lamb波在传播过程中具有频散及多模态特性,若相关参数选择不当,会导致在实际应用中信号相互叠加而无法识别。本文基于Lamb波的频散曲线是其频散方程实数解分布的特点,采用二分法绘制了铝板中Lamb波的频散曲线、波结构曲线和入射角曲线。根据曲线选择S0模态的Lamb波对1mm厚铝板中不同类型的缺陷进行检测。实验结果表明,S0模态的Lamb波对裂纹型缺陷和贯穿型缺陷十分敏感,但对于裂纹型缺陷,其幅值变化并不与缺陷大小成线性关系,并且S0模态Lamb波的声场指向性十分集中,在偏离声束轴线时无法检测到缺陷。     

复合兰姆波声子晶体中超宽部分禁带

兰姆波在声子晶体薄板中的传播特性因其在无损检测、 减振技术和传感器件等领域的潜在应用价值而受到越来越多的关注. 本文采用超原胞平面波展开法和有限元法系统地研究了复合对称结构声子晶体薄板中的兰姆波超宽部分禁带. 结果表明: 对于在薄板侧面对称地嵌入双层矩形空气柱构成的复杂系统, 低阶兰姆波部分带隙结构极为丰富. 将晶格常数(L)和板厚(H) 比值具有匹配关系的兰姆波声子晶体衔接构成复合结构, 低阶兰姆波部分禁带宽度因各组分结构的部分禁带交叠而得到显著拓宽, 可在低频超宽频带内实现对特定低阶兰姆波模式良好的模式选择功能. 该研究结果对兰姆波缺陷无损检测中模式优化选择及兰姆波单向导通器件设计等方面具有重要意义.     

一种定征固体板表面性质的兰姆波方法

基于Ritec-SNAP系统建立了兰姆波实验系统，分析了用兰姆波幅频特性定征固体板表面性质的可行性。实验结果表明，用高阶、多模兰姆波的幅频特性可准确定征固体板表面性质的变化。     

多通道超声兰姆波检测板状结构中的裂纹

超声兰姆(Lamb)波在结构缺陷检测方面愈来愈受到重视,但目前Lamb波的应用局限于单信号源激励,单通道接收的方法,容易受到噪声干扰,其后续的信号分析处理也比较复杂。本文旨在采用多通道Lamb波对板状结构中的裂纹进行定量分析与诊断。在铝板的表面凿刻出不同深度的凹槽作为裂纹,通过线阵换能器采集在一定传播距离内的多通道Lamb波信号,并采用二维傅里叶变换分析在不同深度的裂纹下,Lamb波模式能量的变化规律。结果表明,相对于完好铝板中的Lamb波信号,裂纹的存在会使Lamb波发生模式转换现象,并且转换模式能量百分比随裂纹深度的增加而线性增加。其结果为Lamb波评价板状结构中的裂纹状况提供了一种可能的方法。     

板状材料上加强筋的几何形状对兰姆波透射特性的影响

为研究板状材料上加强筋结构对兰姆波透射特性的影响,通过有限元仿真和实验的方法,结合兰姆波频散曲线和二维傅里叶变换分析方法,研究了不同几何形状的加强筋结构对兰姆波垂直入射时的透射特性。仿真与实验的结果表明:加强筋结构会对兰姆波产生梳状滤波器效应,即同一几何形状的加强筋对不同频率的兰姆波透射程度不同;梳状滤波器的通带带宽和通带个数受到加强筋几何形状的影响;随着加强筋高度的增加,梳状滤波器的通带带宽变小且通带个数增加;随着加强筋厚度的增加,梳状滤波器的通带带宽和个数并不呈现单调变化;对于同一高厚比的加强筋,随着加强筋体积的变大,梳状滤波器的通带宽变小且通带个数增加。该研究结果可用于指导利用兰姆波对具有加强筋结构的板状材料进行结构健康监测和无损检测时兰姆波有效频率的选择,从而提高兰姆波能量的利用率和信号的信噪比。