Selective oxidation of octadecan-1-ol to octadecanoic acid over Co3O4/SiO2 catalysts

Factors (reaction temperature, reaction time, flow rate of oxygen, amount of catalyst, etc.) influencing the catalytic properties of Co₃O₄/SiO₂catalyst in the oxidation octadecan-1-ol to octadecanoic acid were investigated. The catalysts were characterized by means of XRD, FT-IR and N₂-adsorption. The experimental results indicate that under the optimal condition the selectivity to octadecanoic acid reached 97.5 % over 5 % Co₃O₄/SiO₂ catalyst.This revised version was published online in December 2005 with corrections to the Cover Date.     

BiVO4/ZnFe2O4同型异质结光阳极的构筑及其光电催化分解水性能

光生电子-空穴对的复合被认为是限制BiVO₄材料光电催化转换效率的重要原因之一。基于此,通过简单的水热-煅烧方法构筑了BiVO₄/ZnFe₂O₄同型异质结光阳极,BiVO₄/ZnFe₂O₄复合光阳极在1.23 V(vs RHE)下的光电流密度为3.33 mA·cm^-2,较纯BiVO₄提升了2倍(1.20 mA·cm^-2)。相关的结构及性能测试表明,BiVO₄和ZnFe₂O₄形成了带隙错开的n-n异质结,使得光生载流子得到有效分离,更有效地参与水氧化过程,进而提高了BiVO₄的光电催化水分解性能。     

BiVO4/ZnFe2O4同型异质结光阳极的构筑及其光电催化分解水性能

光生电子-空穴对的复合被认为是限制BiVO₄材料光电催化转换效率的重要原因之一。基于此,通过简单的水热-煅烧方法构筑了 BiVO₄/ZnFe₂O₄同型异质结光阳极,BiVO₄/ZnFe₂O₄复合光阳极在 1.23 V(vs RHE)下的光电流密度为 3.33 mA·cm^-2,较纯BiVO₄提升了2倍 (1.20 mA·cm^-2)。相关的结构及性能测试表明,BiVO₄和ZnFe₂O₄形成了带隙错开的n-n异质结,使得光生载流子得到有效分离,更有效地参与水氧化过程,进而提高了BiVO₄的光电催化水分解性能。     

Photocatalytic oxidation of primary and secondary benzylic alcohols to carbonyl compounds catalyzed by H3PW12O40/SiO2 under an O2 atmosphere

An efficient, selective and green procedure for the photocatalytic oxidation of primary and secondary benzylic alcohols to the corresponding aldehydes and ketones has been achieved using silica-encapsulated H₃PW₁₂O₄₀ as a recyclable heterogeneous photocatalyst in acetonitrile under oxygen gas as the sole reoxidant of the catalyst.     

Silver nitrate-catalyzed oxidation of aldehydes to carboxylic acids by H2O2

A variety of aromatic, aliphatic and conjugated aldehydes were converted to the corresponding carboxylic acid derivatives with 30% H₂O₂ as the oxidant in the presence of catalytic amounts of AgNO₃. The method described has wide range of applicabilities, does not involve cumbersome work-up, exhibits chemoselectivity and proceeds under mild reaction conditions, and the resulting products are obtained in good yields within reasonable time.     

Mn-Na2WO4/SiO2催化剂表面活性中心结构的DFT研究

Mn Na2WO4/SiO2 is one of the best catalysts for oxidative coupling of methane.To investigate the nature of active centers and the reaction mechanism,the structure of possible metal sites formed by tungsten and manganese over the silica surface were studied using molecular simulation method and ab initio DFT calculations.Silica support exists in the catalyst as 岐瞔ristobalite and its (111) face exposes preferentially to the surface.The calculated results show that tungsten interacts with the silica surface by three or one bridge oxygen atoms to form tetrahedral [WO4],and manganese interacts with single bridge oxygen to form dispersed [MnO4] or exists as oxide clusters.The nature of the molecular orbitals and the electronic structure suggest that the tetrahedral [WO4] site with single bridge oxygen is the most probable active center responsible for methane activation.     

ZrO4/SiO2-Al2O3催化肉桂醛MPV转移加氢性能

以九水合硝酸铝（Al（NO₃）₃·9H₂O）与正硅酸乙酯（TEOS）为前驱盐,采用溶胶-凝胶法制备一系列不同Al₂O₃含量的SiO₂-Al₂O₃复合氧化物,并通过浸渍硝酸氧锆引入ZrO₂,制备ZrO₂/SiO₂-Al₂O₃复合氧化物催化剂,考察催化剂在肉桂醛（CAL）MPV转移加氢中的催化性能,并结合N₂物理吸附、X射线粉末衍射（XRD）、傅里叶变换红外光谱（FTIR）、NH₃-程度升温脱附（NH₃-TPD）、Py-原位红外（Py-IR）等技术,研究催化剂结构、织构以及表面性质与其催化性能间的构效关系.研究表明,所制备的催化剂均以L酸为主,并含有少量B酸中心,这使得加氢产物以肉桂醇（COL）为主,并含有少量1-苯丙烯-2-丙基醚（CPE）.Al₂O₃含量不仅影响催化剂表面的酸中心数量,而且对催化剂的织构参数有较大影响.随Al₂O₃含量的增加,催化剂表面L酸与B酸中心均有所增加,而孔径则持续变小,这使得催化反应呈现CAL转化率先增加后减少、目标产物COL选择性先稍有减小后有所增加的趋势.在Si/Al比为2时,催化剂具有最优的催化性能,优化反应条件下,CAL转化率达96%,目标产物COL选择性达90%.     

Microwave-promoted efficient conversion of acetophenones to 1,3,5-triarylbenzenes catalyzed by H3PW12O40 and nano-silica supported H3PW12O40 as reusable catalysts

H₃PW₁₂O₄₀ and nano-silica supported H₃PW₁₂O₄₀ were found to be efficient heterogeneous catalysts for the preparation of 1,3,5-triarylbenzenes via triple self condensation of acetophenones under microwave irradiation and solvent-free conditions. High yields, short reaction times, easy work-up, easy availability and handling, eco-friendly and reusability of the catalysts are the main aspects of the present method. The catalytic mechanism of 1,3,5-triarylbenzenes synthesis is also proposed.     

双帽Keggin型杂多阴离子[H4As3Mo12O40]-和Keggin型杂多酸H3PM12O40 (M＝Mo, W)质子化的DFT研究

选用B3LYP方法在LanL2MB水平下, 对双帽α-Keggin型杂多阴离子[H₄As₃Mo₁₂O₄₀]^-的电子结构和质子的定位进行了密度泛函理论(DFT)研究. 结果表明, 双帽的形成大大影响了杂多阴离子[As₃Mo₁₂O₄₀]^5－的电子结构和性质, NBO分析显示参与成帽的三桥氧上的电子密度比双桥氧上的要大, 简单地从电荷密度来看, 质子将首先在三桥氧上定域成键, 但通过比较质子定域在几种桥氧上质子化稳定化能的大小, 发现[H₄As₃Mo₁₂O₄₀]^-中的四个质子将在八个双桥氧中的其中四个氧原子上定位, 而不是如文献中报道的在四个三桥氧上定域成键. 对杂多酸H₃PM₁₂O₄₀ (M＝Mo, W)中质子的定位也进行了理论计算并与文献进行了比较, 结果显示, H₃PMo₁₂O₄₀中质子是定位在双桥氧上; 而H₃PW₁₂O₄₀中质子将优先在双桥氧上定位, 但也可在端氧上定位; 这一结果与文献报道的相一致.     

Mn修饰Al2O3载体负载Pd催化剂及其蒽醌加氢催化性能

以活性氧化铝(γ-Al2O3)为载体,分别以Mn(NO3)2溶液和酸性氯化钯(PdCl2)溶液为修饰组分和活性组分前体,采用分步浸渍法制备了Mn修饰Al2O3载体负载钯催化剂。将催化剂应用于蒽醌加氢反应,考察了催化剂制备方法、活性组分负载量和催化剂还原温度对反应效果的影响。用XRD、BET、XPS和TPR对催化剂进行了表征。结果表明,催化剂活性受到制备方法的影响,在对Mn修饰Al2O3载体进行焙烧,Pd负载量0.2(wt)%、还原温度300℃的条件下,催化剂蒽醌加氢活性较高,较未修饰的催化剂提高了约16%。催化剂中Mn以MnO的形式存在,影响了γ-Al2O3的组织结构,使载体与活性组分之间的作用力增强,活性组分Pd高度分散在催化剂表面,从而提高了催化剂的活性。     

SiO_2/Co_3O_4核壳催化剂对AP热分解的催化性能研究

采用改良的St觟ber法制备粒径约为200 nm的单分散球形SiO2颗粒,以此为内核,分别通过液相沉淀法和尿素均匀沉淀法制备包覆形式不同的新型SiO2/Co3O4核壳式纳米催化剂。采用X-射线衍射分析(XRD)、透射电子显微镜(TEM)、红外光谱分析(IR)、拉曼光谱分析(Raman)、BET比表面积测试等手段对产物进行表征,利用差式扫描量热仪(DSC)考察SiO2/Co3O4复合物对高氯酸铵(AP)热分解反应的催化作用,探讨不同包覆形式对其催化活性的影响。结果表明,两种方法制备得到的SiO2/Co3O4复合物分别为层包覆和粒子包覆,比表面积大,具有明显的核壳结构,且粒子包覆形式的SiO2/Co3O4对AP热分解反应的催化效果最好,使AP的高温分解温度降低了110℃,放热量增加了662 J·g-1。     

SiO2负载氮掺杂TiO2可见光响应光催化剂的制备及性能

以四氯化钛为钛源,尿素为氮源,采用液相水解-沉淀法制得SiO2负载N掺杂TiO2可见光响应TiO2-xNy/SiO2光催化剂(TSN)。以苯酚为模型物,考察了TSN在可见光区、紫外光区及太阳光下的光催化活性,以及催化剂的使用寿命、分离性能。采用XPS、FTIR、UV-Vis DRS、XRD、TEM和低温氮物理吸附等对催化剂的结构进行表征。结果表明,N以阴离子形式进入TiO2体相并置换晶格中的O,适量N掺杂的TSN在紫外光区、可见光区及太阳光下均表现出较高的活性。SiO2与TiO2界面间有Ti-O-Si键形成,结合牢固。N掺杂在TiO2表面生成Ti-O-N键,形成新的能级结构,使催化剂的吸收红移至450~500 nm,诱发TiO2可见光催化活性。SiO2负载可减小TiO2颗粒平均尺寸,增加催化剂比表面积;同时SiO2负载还可改善催化剂的分离性能,提高催化剂使用寿命。     

铈钛混合氧化物负载磷钨酸吸附-分解NOx性能

通过软化学途径合成了铈钛混合氧化物(CeO₂-TiO₂)载体材料, 并分别通过等体积浸渍法和机械研磨法负载磷钨酸(H₃PW₁₂O₄₀)。采用FTIR、XRD、SEM和BET比表面积测定对CeO₂-TiO₂及负载型多酸催化剂进行了表征;考察了负载量、负载方法、吸附温度等因素对催化剂吸附NO_x效率的影响;选取吸附性能最佳的催化剂进行了NO_x催化分解实验, 探讨了NO_x吸附-分解机理。结果表明:相对于等体积浸渍法, 机械研磨法更适合此类载体负载H₃PW₁₂O₄₀, 其NO_x吸附效率均高于H₃PW₁₂O₄₀及载体本身;在0~60%的负载量范围内, 随着H₃PW₁₂O₄₀负载量的增加, 负载型催化剂吸附NO_x的效率呈上升趋势, 负载量为40%时NO_x吸附效率最佳, 达90%;吸附过程中NO_x与催化剂活性组分H₃PW₁₂O₄₀发生作用, 生成NOH⁺, H₃PW₁₂O₄₀二级结构中结晶水对催化剂吸附NO_x有重要作用;当温度从150℃升至 450℃时, 被吸附的NO_x发生分解, 分解产物的组成与N₂的收率均受升温速率的影响, 升温速率越快, N₂收率越高。向吸附分解NO_x后的催化剂床层通入含有水蒸气的空气, 可有效补充NO_x分解过程中H₃PW₁₂O₄₀失去的结晶水, 从而恢复催化剂优良的NO_x吸附分解性能, 实现催化剂的有效再生利用。     

铈钛混合氧化物负载磷钨酸吸附-分解NOx性能

通过软化学途径合成了铈钛混合氧化物(CeO2-TiO2)载体材料,并分别通过等体积浸渍法和机械研磨法负载磷钨酸(H3PW12O40)。采用FTIR、XRD、SEM和BET比表面积测定对CeO2-TiO2及负载型多酸催化剂进行了表征;考察了负载量、负载方法、吸附温度等因素对催化剂吸附NOx效率的影响;选取吸附性能最佳的催化剂进行了NOx催化分解实验,探讨了NOx吸附-分解机理。结果表明:相对于等体积浸渍法,机械研磨法更适合此类载体负载H3PW12O40,其NOx吸附效率均高于H3PW12O40及载体本身;在0~60%的负载量范围内,随着H3PW12O40负载量的增加,负载型催化剂吸附NOx的效率呈先升后降趋势,负载量为40%时NOx吸附效率最佳,达90%;吸附过程中NOx与催化剂活性组分H3PW12O40发生作用,生成NOH+;H3PW12O40二级结构中结晶水对催化剂吸附NOx有重要作用;当温度从150℃升至450℃时,被吸附的NOx发生分解,分解产物的组成与N2的收率均受升温速率的影响,升温速率越快,N2收率越高。向吸附分解NOx后的催化剂床层通入含有水蒸气的空气,可有效补充NOx分解过程中H3PW12O40失去的结晶水,从而恢复催化剂优良的NOx吸附分解性能,实现催化剂的有效再生利用。     

SiO2/Co3O4核壳催化剂对AP热分解的催化性能研究

采用改良的Stöber法制备粒径约为200 nm的单分散球形SiO₂颗粒,以此为内核,分别通过液相沉淀法和尿素均匀沉淀法制备包覆形式不同的新型SiO₂/Co₃O₄核壳式纳米催化剂。采用X-射线衍射分析(XRD)、透射电子显微镜(TEM)、红外光谱分析(IR)、拉曼光谱分析(Raman)、BET比表面积测试等手段对产物进行表征,利用差式扫描量热仪(DSC)考察SiO₂/Co₃O₄复合物对高氯酸铵(AP)热分解反应的催化作用,探讨不同包覆形式对其催化活性的影响。结果表明,两种方法制备得到的SiO₂/Co₃O₄复合物分别为层包覆和粒子包覆,比表面积大,具有明显的核壳结构,且粒子包覆形式的SiO₂/Co₃O₄对AP热分解反应的催化效果最好,使AP的高温分解温度降低了110 ℃,放热量增加了662 J·g^-1。     

大尺寸TiO2/SiO2大孔材料的制备及光降解性能

先以三维骨架聚合物为整体型模板,利用硅酸酯原位溶胶-凝胶过程并结合高温烧结的方法制备出大尺寸大孔径的SiO2载体,然后通过钛酸丁酯溶液浸渍、原位水解、煅烧制备出大尺寸的TiO2/SiO2大孔材料并用SEM、TEM、FTIR、XRD和XPS对其表征,结果表明SiO2载体具有三维连续的超薄层,TiO2以纳米薄层方式均匀地沉积在SiO2的三维超薄层上,形成TiO2/SiO2/TiO2三层夹心结构,层与层界面存在Si-O-Ti键,同时复合结构提高了TiO2由锐钛矿相向金红石相的转变温度.以甲基橙为目标降解物考察不同条件下制备的复合材料的光催化活性,采用复合材料吸入甲基橙溶液的方式,并借助甲醇萃取手段研究光降解动力学过程.结果表明,该复合材料具有较好的光降解催化活性,当焙烧温度为600℃和TiO2的负载量为54.5wt%时,其活性最大且降解速率常数达到1.78 h-1.     

Cs取代对Ni-H3PW12O40/SiO2催化剂结构性质和催化性能的影响

采用两步浸渍法和载体上的原位反应制备了一系列Cs部分取代的Ni-Cs_xH_3-xPW₁₂O₄₀/SiO₂催化剂,并用N₂吸附比表面积测定(BET)、电感耦合等离子体发射光谱(ICP)、X射线衍射(XRD)、拉曼光谱(Raman)、原位X射线衍射(in situ XRD)、NH₃程序升温脱附(NH₃-TPD)、H₂程序升温还原(H₂-TPR)、H₂程序升温脱附(H₂-TPD)、吡啶吸附傅里叶变换红外(FTIR)光谱等分析测试技术对催化剂进行了表征. 以正癸烷为模型化合物,对催化剂的加氢裂化性能进行了评价. 结果表明,8%Ni-50%Cs_1.5H_1.5PW/SiO₂催化剂具有最高的C₅₊收率,明显优于8%Ni-50%H₃PW/SiO₂催化剂和工业催化剂. 随着Cs 在Cs_xH_3-xPW中比例的增加,正癸烷的转化率逐渐降低,而C₅₊选择性则逐渐提高. 当催化剂具有合适的孔径时,选择性的提高是由于催化剂酸性的减弱,而转化率的降低则是由于催化剂加氢能力的减弱.     

The release of TiO2 and SiO2 nanoparticles from nanocomposites

There is a growing interest in the development of nanocomposites consisting of organic polymers and TiO₂ or amorphous SiO₂ nanoparticles. These nanoparticles may be released from nanocomposites. There is evidence that amorphous SiO₂ and TiO₂ nanoparticles can be hazardous. Thus, in the design of nanocomposites with such nanoparticles, hazard reduction extending to the full nanocomposite life cycle would seem a matter to consider. Options for hazard reduction include: changes of nanoparticle surface, structure or composition, better fixation of nanoparticles in nanocomposites, including persistent suppression of oxidative damage to polymers by nanoparticles, and design changes leading to the release of relatively large particles.     

Synthesis and characterization of Fe2O3/SiO2 nanocomposites

Fe₂O₃/SiO₂ nanocomposites based on fumed silica A-300 (S_BET = 337 m²/g) with iron oxide deposits at different content were synthesized using Fe(III) acetylacetonate (Fe(acac)₃) dissolved in isopropyl alcohol or carbon tetrachloride for impregnation of the nanosilica powder at different amounts of Fe(acac)₃ then oxidized in air at 400–900 °C. Samples with Fe(acac)₃ adsorbed onto nanosilica and samples with Fe₂O₃/SiO₂ including 6–17 wt% of Fe₂O₃ were investigated using XRD, XPS, TG/DTA, TPD MS, FTIR, AFM, nitrogen adsorption, Mössbauer spectroscopy, and quantum chemistry methods. The structural characteristics and phase composition of Fe₂O₃ deposits depend on reaction conditions, solvent type, content of grafted iron oxide, and post-reaction treatments. The iron oxide deposits on A-300 (impregnated by the Fe(acac)₃ solution in isopropanol) treated at 500–600 °C include several phases characterized by different nanoparticle size distributions; however, in the case of impregnation of A-300 by the Fe(acac)₃ solution in carbon tetrachloride only α-Fe₂O₃ phase is formed in addition to amorphous Fe₂O₃. The Fe₂O₃/SiO₂ materials remain loose (similar to the A-300 matrix) at the bulk density of 0.12–0.15 g/cm³ and S_BET = 265–310 m²/g.     

静电自组装制备纳米TiO2/SiO2光催化材料

采用静电自组装方法制备了纳米TiO2/SiO2光催化材料。采用巯丙基三甲氧基硅烷偶联剂对SiO2进行干法改性,采用双氧水/冰醋酸将偶联剂巯基基团氧化为磺酸基基团。在正负电荷的吸引下,带负电荷的SiO2与带正电荷的钛聚合阳离子自发地组装在一起,经一定温度热处理得到纳米TiO2/SiO2光催化材料。采用XRD、FTIR、PL、UV-Vis DRS、SEM和ICP等对材料进行了分析和表征。采用甲基橙溶液评价材料的光催化性能。结果表明:SiO2促使锐钛矿的形成,抑制锐钛矿向金红石的转变,减小TiO2的晶粒尺寸,使得TiO2光吸收波长发生蓝移。TiO2与SiO2通过Si-O-Ti键发生结合。采用静电自组装方法制备的材料中TiO2的含量高于传统方法,导致材料的光催化性能有所提高。