Amperometric method for the determination of myoglobin based on the electrochemical reduction on the glassy carbon electrode

An irreversible reduction peak of oxymyoglobin (MbO₂) was observed on the bare glassy carbon electrode (GCE) in acetate buffer solution under atmospheric conditions. It is the reduction of bonded oxygen in Mb, but not the heme Fe(III)/Fe(II) redox couple that underwent electrochemical reaction on the electrode. The peak current achieved a maximum value in acetate buffer solution of pH 4.0. The peak potential was pH dependent, suggesting that the proton was involved in the electrochemical reaction. Furthermore, the peak current was linearly related to the concentration of myoglobin in the range of 2.5 × 10^–8～ 1.0 × 10^–6 mol · L^–1 with a detection limit of 5 × 10^–9 mol · L^–1.     

Adsorptive anodic stripping voltammetry of zirconium(IV)-alizarin red S complex at a carbon paste electrode

A sensitive adsorptive anodic stripping procedure for the determination of trace zirconium at a carbon paste electrode (CPE) has been developed. The method is based on adsorptive accumulation of the Zr(IV)-alizarin red S(ARS) complex onto the surface of the CPE, followed by oxidation of adsorbed species. The optimal experimental conditions include the use of 0.10 mol · L⁻¹ ammonium acetate buffer (pH 4.3), ARS, an accumulation potential of 0.20 V (versus SCE), an accumulation time of 2 min, a scan rate of 200 mV · s⁻¹ and a second-order derivative linear scan mode. The oxidation peak for the complex appears at 0.69 V. The peak current is proportional to the concentration of Zr(IV) over the range of 1.0 × 10⁻⁹–2.0 × 10⁻⁷ mol · L⁻¹, and the detection limit is 3 × 10⁻¹⁰ mol · L⁻¹ for a 2 min adsorption time. The relative standard deviations (n = 8) for 5.0 × 10⁻⁸ and 5.0 × 10⁻⁹ mol · L⁻¹ Zr(IV) are 3.3 and 4.8%, respectively. The proposed method was applied to the determination of zirconium in ore samples with satisfactory results.     

Determination of rutin using a CeO2 nanoparticle-modified electrode

CeO₂ nanoparticles approximately 12 nm in size were synthesized and subsequently characterized by XRD, TEM and UV-vis spectroscopy. Then, a gold electrode modified with CeO₂ nanoparticles was constructed and characterized by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The modified electrode demonstrated strong catalytic effects with high stability towards electrochemical oxidation of rutin. The anodic peak currents (measured by differential pulse voltammetry) increased linearly with the concentration of rutin in the range of 5.0 × 10⁻⁷–5.0 × 10⁻⁴ mol · L⁻¹. The detection limit (S/N = 3) was 2.0 × 10⁻⁷ mol · L⁻¹. The relative standard deviation (RSD) of 8 successive scans was 3.7% for 5.0 × 10⁻⁶ mol · L⁻¹ rutin. The method showed excellent sensitivity and stability, and the determination of rutin in tablets was satisfactory.     

Determination of EDTA in used fixing solutions by capillary electrophoresis

A capillary electrophoretic method for the determination of EDTA has been developed. EDTA was converted to Ni(II)-EDTA prior to separation, separated from Fe(III)-EDTA, thiosulphate, bromide and polythionates using a fused silica capillary (57 cm × 75 μm I.D.) filled with a borate buffer (50 mmol L^–1; pH 8.5; applied voltage, 30 kV) and detected at 214 nm. The separation time is about 6 min. The detection limit achieved is 2 × 10^–6 mol L^–1 for EDTA. This method was applied for the determination of free EDTA in used fixing solutions. Received: 27 February 1998 / Revised: 28 April 1998 / Accepted: 20 May 1998     

Determination of EDTA in used fixing solutions by capillary electrophoresis

A capillary electrophoretic method for the determination of EDTA has been developed. EDTA was converted to Ni(II)-EDTA prior to separation, separated from Fe(III)-EDTA, thiosulphate, bromide and polythionates using a fused silica capillary (57 cm × 75 μm I.D.) filled with a borate buffer (50 mmol L^–1; pH 8.5; applied voltage, 30 kV) and detected at 214 nm. The separation time is about 6 min. The detection limit achieved is 2 × 10^–6 mol L^–1 for EDTA. This method was applied for the determination of free EDTA in used fixing solutions. Received: 27 February 1998 / Revised: 28 April 1998 / Accepted: 20 May 1998     

Electrochemical behavior of uric acid at a penicillamine self-assembled gold electrode

The fabrication and electrochemical characteristics of a penicillamine (PCA) self-assembled monolayer modified gold electrode were investigated. The electrode can enhance the electrochemical response of uric acid (UA), and the electrochemical reaction of UA on the PCA electrode has been studied by cyclic voltammetry and differential pulse voltammetry. Some electrochemical parameters, such as diffusion coefficient, standard rate constant, electron transfer coefficient and proton transfer number have been determined for the electrochemical behavior on the PCA self-assembled monolayer electrode. The electrode reaction of UA is an irreversible process, which is controlled by the diffusion of UA with two electrons and two protons transfer at the PCA/Au electrode. In phosphate buffer (pH 5.0), the peak current is proportional to the concentration of UA in the range of 6.0 × 10⁻⁵–7.0 × 10⁻⁴ mol L⁻¹ and 2.0 × 10⁻⁵–7.0 × 10⁻⁴ mol L⁻¹ for the cyclic voltammetry and differential pulse voltammetry methods with the detection limits of 5.0 × 10⁻⁶ and 3.0 × 10⁻⁶ mol L⁻¹, respectively. The method can be applied to determine UA concentration in real samples.     

Covalent Modification of Glassy Carbon Electrode with L-Cysteine for the Determination of Acetaminophen

A novel L-cysteine film modified electrode has been fabricated by means of an electrochemical oxidation procedure, and it was successfully applied to the electrochemical determination of acetaminophen. This method utilizes the electrooxidation of amines to their analogous cation radicals to form a chemically stable covalent linkage between the nitrogen atom of the amine and edge plane sites at the glassy carbon electrode surface. The electrochemical behaviour of acetaminophen at the film electrode was investigated in 0.1 mol L⁻¹ phosphate buffer (pH 6.20). It was found that the redox peak current of acetaminophen was enhanced greatly on the film electrode. Linearity between the oxidation peak current and the acetaminophen concentration was obtained in the range of 1.0 × 10⁻⁴–2.0 × 10⁻⁷ mol L⁻¹ with a detection limit of 5.0 × 10⁻⁸ mol L⁻¹. For seven parallel detections of 1.0 × 10⁻⁵ mol L⁻¹ acetaminophen, the relative standard deviation (RSD) was 1.46%, suggesting that the film electrode has excellent reproducibility. Application to the determination of acetaminophen in drug tablets and human urine demonstrated that the film electrode has good stability and high sensitivity.     

Trace determination of clenbuterol with an MWCNT-Nafion nanocomposite modified electrode

A method for the determination of trace clenbuterol is described. Multi-walled carbon nanotubes (MWCNTs)-Nafion composite was used to modify the glassy carbon electrode (GCE). The modified electrode showed high sensitivity and good selectivity for clenbuterol detection. It offered a linear range of 1.0 × 10⁻⁹–1.0 × 10⁻⁶ mol · L⁻¹ with a detection limit of 5.0 × 10⁻¹⁰ mol · L⁻¹ in pH = 1.2 solution. The oxidation mechanism of clenbuterol on the electrode was also investigated. Correspondence: Xiao-Ya Hu, Department of Chemistry, Yang Zhou University, Yang Zhou, Jiang Su, P.R. China     

Electrochemical determination of ascorbic acid using the poly-cysteine film-modified electrode

A poly(L-cysteine) thin film was prepared onto electrode surface via electropolymerization. In pH 7.0 phosphate buffer, L-cysteine was oxidized during the cyclic potential sweep between −0.60 and 2.00 V, forming a thin film at the glassy carbon electrode (GCE) surface. The electrochemical behaviors of ascorbic acid at the bare GCE and the poly(L-cysteine) film-coated GCE were investigated. The oxidation peak potential of ascorbic acid shifts to more negative potential at the poly(L-cysteine) film-modified GCE. Moreover, the oxidation peak current significantly increases at the poly(L-cysteine) film-modified GCE. These phenomena indicate that poly(L-cysteine) film shows highly-efficient catalytic activity to the oxidation of ascorbic acid. Based on this, a sensitive and simple electrochemical method was proposed for the determination of ascorbic acid. The oxidation peak current of ascorbic acid is proportional to its concentration over the range from 1.0 × 10⁻⁶ to 5.0 × 10⁻⁴ mol l⁻¹. The limit of detection is evaluated to be 4.0 × 10⁻⁷ mol l⁻¹.     

Preconcentration and voltammetric determination of palladium (II) at sodium humate modified carbon paste electrodes

A chemically modified carbon paste electrode was prepared by incorporating appropriate amounts of sodium humate(NaA). Palladium(II) was selectively accumulated in a solution of Britton-Robinson(B-R) buffer (pH 2.8) onto the electrode surface in open circuit mode. The subsequent electrochemical measurement was carried out by cyclic voltammetry (CV) and linear sweep anodic stripping voltammetry (LSASV) in a supporting electrolyte of 1.0 M HCl. The obtained oxidation currents (I_pa1 and L_pa2) were proportional to the Pd(II) concentration in the range of 4.7 × 10^–6 - 9.4 × 10^–8 M. The developed method was applied to the quantitative determination of palladium in real samples. Received: 6 March 1998 / Revised: 3 June 1998 / Accepted: 3 July 1998     

Development of a voltammetric method for the determination of iron(III) in Zn-Fe alloy galvanic baths

A square wave voltammetric method whith a static mercury drop electrode (SMDE) was developed for the quantitative determination of iron (III) in Zn-Fe alloy galvanic baths. Real alloy bath samples were analyzed by the standard addition method and recovery tests were carried out. 0.50 mol L^–1 sodium citrate (pH 6.0) or 0.20 mol L^–1 oxalic acid (pH 4.0) were applied as supporting electrolytes resulting in both cases in a peak potential of about –0.20 V vs. Ag|AgCl (saturated KCl). The iron (III) concentration in the alloy bath was 9.0 × 10^–4 mol L^–1. A good correlation (r = 0.9999) was achieved between the iron (III) concentration and the peak current in the electrolytes studied, with linear response ranges from 1.0 × 10^–6 to 1.2 × 10^–4 mol L^–1. Interference levels for some metals such as copper (II), lead (II), chromium (III) and manganese (II) that can hinder the Zn-Fe alloy deposition were evaluated; only copper (II) interferes seriously. Received: 4 April 2000 / Revised: 19 June 2000 / Accepted: 22 June 2000     

Application of a Single-Wall Carbon Nano-Tube Film Electrode to the Determination of Trace Amounts of Folic Acid

Single-wall carbon nano-tubes were used to modify the surface of a glassy carbon electrode (GC) and applied in the determination of folic acid with voltammetry. The experiments demonstrated that the presence of a carbon nano-tube film on the electrode greatly increased the reduction peak current of folic acid. Cyclic voltammetry (CV) and linear sweep voltammetry (LSV) were used in a comparative investigation of the electrochemical reduction of folic acid with the film electrode. Effects of pH on the peak current and the peak potential were studied in the pH range of 4.0–8.0 with Britton-Robinson buffer solution. The reduction peak current was found to be linearly related to folic acid concentration over the range of 1 × 10⁻⁸ to 1 × 10⁻⁴ mol L⁻¹ with a detection limit of 1 × 10⁻⁹ mol L⁻¹ after 5 min accumulation. The film electrode provides an efficient way for eliminating interferences from some inorganic and organic species in the solution. The high sensitivity, selectivity and stability of the film electrode demonstrate its practical application from a simple and rapid determination of folic acid in tablets.     

Electrochemical behavior and determination of epinephrine at a mercaptoacetic acid self-assembled gold electrode

The electrochemical behavior of epinephrine (EP) at a mercaptoacetic acid (MAA) self-assembled monolayer modified gold electrode was studied. The MAA/Au electrode is demonstrated to promote the electrochemical response of epinephrine by cyclic voltammetry. The possible reaction mechanism is also discussed. The diffusion coefficient D of EP is 6.85 × 10⁻⁶ cm² s⁻¹. In 0.1 mol L⁻¹ phosphate buffer (pH 7.20), a sensitive oxidation peak was observed at 0.177 V, and the peak current is proportional to the concentration of EP in the range of 1.0 × 10⁻⁵–2.0 × 10⁻⁴ mol L⁻¹ and 1.0 × 10⁻⁷–1.0 × 10⁻⁶ mol L⁻¹. The detection limit is 5 × 10⁻⁸ mol L⁻¹. The modified electrode is highly stable and can be applied to the determination of EP in practical injection samples. The method is simple, quick, sensitive and accurate.     

Electrochemical deposition of silicate–cetyltrimethylammonium bromide nanocomposite film on glassy carbon electrode for sensing of methyl parathion

A novel electrochemical sensor for methyl parathion based on silicate– cetyltrimethylammonium bromide nanocomposite film has been fabricated by electro-assisted deposition onto glassy carbon electrode in one-step via an electrochemical modulation of pH at the electrode/solution interface to promote controlled gelification of tetraethylorthosilicate sol, and was characterized with scanning electron microscopy, X-ray diffraction, and electrochemical impedance spectroscopy. The electrochemical sensing of methyl parathion on the film-modified electrode was investigated applying cyclic voltammetry and square wave voltammetry. Compared to the unmodified electrode, the shapes of the redox peaks were improved and the peak currents significantly increased. Experimental parameters such as deposition time, pH value, and accumulation conditions have been optimized. A linear relationship between the peak current and methyl parathion concentration was obtained in the range from 1.0 × 10⁻⁷ to 1.0 × 10⁻⁴ mol L⁻¹ with a detection limit of 1.04 × 10 ⁻⁸ mol L⁻¹ (S/N = 3) after accumulation at 0 V for 120 s. The film electrode shows great promise for determination of methyl parathion in real samples.      

Electrochemical behaviors of GMP based on solid-phase extractionon at Cu-Mg-Al hydrotalcite-like compound (HTLC) modified glass carbon electrode

Guanosine-5′-monophosphate (GMP) was investigated the electrochemical behaviors based on solid-phase extractionon (SPE) at Cu-Mg-Al hydrotalcite-like compound (HTLC) modified glass carbon electrode. Cu-Mg-Al hydrotalcite-like compound (HTLC) was proved as a new sorbent for SPE of GMP, which showed an irreversible adsorption oxidation process on the HTLC/GCE with the oxidation peak potential located at 1.15 V (vs. SCE) in a pH 5.0 acetate buffer solution. Influencing factors of the electrochemical behavior of GMP on the HLTC/GCE were optimized and kinetic parameters were calculated. Under the optimal conditions, with differential pulse voltammetry (DPV), a linear relationship was obtained between the oxidation peak current and the GMP concentration in the range from 1.0 × 10^− 6 to 8.0 × 10⁻⁴ mol L⁻¹ with the detection limit as 5.0 × 10⁻⁷ mol L⁻¹ (signal-to-noise ratio of 3). The modified electrode surface has very good reproducibility and stability.     

Determination of the pesticide Chlorpyrifos by cathodic adsorptive stripping voltammetry

The adsorption behavior and differential pulse cathodic adsorptive stripping voltammetry of the pesticide Chlorpyrifos (CP) were investigated at the hanging mercury drop electrode (HMDE). The pesticide was accumulated at the HMDE and a well-defined stripping peak was obtained at –1.2 V vs Ag/AgCl electrode at pH 7.50. A voltammetric procedure was developed for the trace determination of Chlorpyrifos using differential pulse cathodic adsorptive stripping voltammetry (DP-CASV). The optimum working conditions for the determination of the compound were established. The peak current was linear over the concentration range 9.90 × 10^–8– 5.96 × 10^–7 mol/L of Chlorpyrifos. The influence of diverse ions and some other pesticides was investigated. The analysis of Chlorpyrifos in commercial formulations and treated waste water was carried out satisfactorily Received: 10 July 1997 / Revised: 1 April 1998 / Accepted: 6 April 1998     

Electrochemical properties and square-wave voltammetric determination of pravastatin

The electrochemical reduction and adsorptive voltammetric behaviour of pravastatin have been studied by means of cyclic and square-wave voltammetry at a hanging mercury-drop electrode in electrolytes of different pH. Within the entire pH range (2.0–9.0) in Britton–Robinson buffer, pravastatin gave rise to a single voltammetric peak in the potential interval from −1.22 to −1.44 V, depending on pravastatin concentration. It was found that the reduction of pravastatin proceeds via a relatively stable intermediate, which is transformed to the final electroinactive product by a coupled chemical reaction or can be re-oxidized back to pravastatin. The rate of chemical transformation is controlled by the proton concentration. The electrode mechanism has the properties of a surface redox reaction. A sensitive analytical method for trace analysis of pravastatin based on the adsorptive stripping technique has been developed. The calibration plot was linear in the range 8×10⁻⁸–5×10⁻⁷ mol L⁻¹. Application of the square-wave voltammetric method to determination of pravastatin in a pharmaceutical dosage form, without sample pretreatment, resulted in acceptable deviation from the stated concentration.     

Ensemble of carbon fiber ultra-microelectrodes modified with nanotubes, and its application to the determination of dopamine

An ensemble of carbon fibers ultra-microelectrode modified with carbon nanotubes (EUME-CNTS) has been constructed based on a thin carbon nanotubes film which was coated onto surfaces of carbon fibers of ultra-microelectrode. SEM micrographs illustrated the image of carbon nanotubes on the carbon fiber surface. The electrochemical characteristics of the EUME-CNTS has been investigated by cyclic voltammetry. The electrochemical properties of dopamine on this electrode were also studied, and the detection limit was found to be 2.0 × 10⁻⁹ mol·L⁻¹. Linear calibration plots were obtained for the oxidation peak current in a range 1.0 × 10⁻⁷–8.0 × 10⁻⁵ mol·L⁻¹. Correspondence: Xiuhua Liu, Kuaizhi Liu, Department of Chemistry and Chemical Engineering, Henan University, Henan Kaifeng 475001, P.R. China     

Covalent modification of glassy carbon electrodes with glycine for voltammetric separation of dopamine and ascorbic acid

Glycine was covalently grafted on to a glassy carbon electrode (GCE) by amine cation radical formation in electrooxidation of the amino-containing compound. X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry proved the immobilization of glycine on the GCE. The modified electrode reduced the overpotentials of dopamine (DA) and ascorbic acid (AA) by approximately 0.15 V and 0.23 V, respectively, and resolved the overlapping voltammetric response of DA and AA into two well-defined voltammetric peaks in cyclic voltammetry (CV) or differential pulse voltammetry (DPV), unlike the unmodified GCE; this can be used for the simultaneous determination of these species in a mixture. The differential pulse peak current was linearly dependent on DA and AA concentration in the range 5 × 10^–6– 8 × 10^–4 mol L^–1 and 6 × 10^–5– 4 × 10^–3 mol L^–1, with correlation coefficients of 0.996 and 0.994, respectively. The detection limits (3δ) for DA and AA were 1.8 × 10^–6 mol L^–1 and 2.1 × 10^–5 mol L^–1, respectively. The modified electrode is very sensitive, selective and stable, and has been applied to the determination of DA and AA simultaneously in samples with satisfactory results. Received: 30 October 2000 / Revised: 9 March 2001 / Accepted: 13 March 2001     

Voltammetric study of the interaction of the ofloxacin–copper complex with DNA, and its analytical application

The electrochemical behavior of the ofloxacin–copper complex, Cu(II)L₂, at a mercury electrode, and the interaction of DNA with the complex have been investigated. The experiments indicate that the electrode reaction of Cu(II)L₂ is an irreversible surface electrochemical reaction and that the reactant is of adsorbed character. In the presence of DNA, the formation of the electrochemically non-active complexes Cu(II)L₂-DNA, results in the decrease of the peak current of Cu(II)L₂. Based on the electrochemical behavior of the Cu(II)L₂ with DNA, binding by electrostatic interaction is suggested and a new method for determining nucleic acid is proposed. Under the optimum conditions, the decrease of the peak current is in proportional to the concentration of nucleic acids in the range from 3 × 10⁻⁸ to 3 × 10⁻⁶ g · mL⁻¹ for calf thymus DNA, from 1.6 × 10⁻⁸ to 9.0 × 10⁻⁷ g · mL⁻¹ for fish sperm DNA, and from 3.3 × 10⁻⁸ to 5.5 × 10⁻⁷ g · mL⁻¹ for yeast RNA. The detection limits are 3.3 × 10⁻⁹, 6.7 × 10⁻⁹ and 8.0 × 10⁻⁹ g · mL⁻¹, respectively. The method exhibits good recovery and high sensitivity in synthetic samples and in real samples.