提高布里渊光时域反射应变仪测量空间分辨力的等效脉冲光拟合法

由于探测光脉冲宽度受到限制,布里渊光时域反射仪(BOTDR)在对光纤上的应变进行分布式测量时,空间分辨力只能达到1 m。针对布里渊光时域反射仪单次采样接收背向布里渊散射信号(BBS)需要一定的时间,提出了基于等效脉冲光的多洛仑兹拟合法以提高其应变测量的空间分辨力。该方法将探测光脉冲在布里渊光时域反射仪完成单次采样所需的时间上进行积分,将积分函数作为等效脉冲光的表达式,再根据等效脉冲光的形状将布里渊光时域反射仪接收到的背向布里渊散射谱(BBS)细分,并对它进行多洛仑兹迭代拟合,准确求得每个细分布里渊散射谱的中心频率,进而利用光纤中布里渊频移与应变的对应关系,得到光纤中与细分布里渊散射谱对应的细分光纤单元上的应变情况。实验结果表明,利用这种方法,可使布里渊光时域反射仪应变测量的空间分辨力提高至0.05 m。     

Acoustic pulse echoes probed with time-resolved X-ray triple-crystal diffractometry

Acoustic pulse echoes generated by femtosecond laser irradiation were detected using time-resolved x-ray triple-crystal diffractometry. The determined time-dependent longitudinal strain component for pulse echoes in silicon and gallium arsenide plates showed that the polarity of the strain pulse was dependent on the optically induced initial stress, and that the bipolar pulse waveform was gradually deformed and broadened in the course of propagation. The three-dimensional wave front distortion of pulse echoes was shown simply as the pulse duration broadening, which was consistent with a boundary roughness for an unpolished plate.     

Soliton mechanism of acoustic pulse frequency conversion to the red region

Self-scattering of a transverse acoustic pulse from a longitudinal strain video pulse (induced by an acoustic pulse) in a paramagnetic crystal in a magnetic field is predicted. This effect is accompanied by a continuous frequency shift of the hypersonic pulse to the red region; this shift is proportional to the pulse intensity.     

入射波整形技术的实验和理论研究

 在硅橡胶材料的分离式霍普金森压杆实验中,实验研究了如何实现常应变率加载,并且得到了整形器尺寸与加载应变率之间,以及加载应变率与试样厚度之间的定量关系。根据预估入射波形的理论模型,给出了采用H62黄铜整形器整形后入射波形的计算结果和实验结果,二者基本上是一致的。     

Dislocation unpinning model of acoustic emission from alkali halide crystals

The present paper reports the dislocation unpinning model of acoustic emission (AE) from alkali halide crystals. Equations are derived for the strain dependence of the transient AE pulse rate, peak value of the AE pulse rate and the total number of AE pulse emitted. It is found that the AE pulse rate should be maximum for a particular strain of the crystals. The peak value of the AE pulse rate should depend on the volume and strain rate of the crystals, and also on the pinning time of dislocations. Since the pinning time of dislocations decreases with increasing strain rate, the AE pulse rate should be weakly dependent on the strain rate of the crystals. The total number of AE should increase linearly with deformation and then it should attain a saturation value for the large deformation. By measuring the strain dependence of the AE pulse rate at a fixed strain rate, the time constantτ _s for surface annihilation of dislocations and the pinning timeτ _p of the dislocations can be determined. A good agreement is found between the theoretical and experimental results related to the AE from alkali halide crystals.     

Nonlinear acoustic transparency phenomena in strained paramagnetic crystals

Nonlinear dynamics of longitudinal acoustic pulses propagating in a strained paramagnetic cubic crystal at low temperature is analyzed. The direction of constant uniform strain is parallel to one of the fourth-order symmetry axes. Effective-spin 1 ions are considered as paramagnetic impurities with the strongest spin-lattice interaction. In this medium, normally degenerate magnetic sublevels are dynamically shifted by the quadrupole Stark effect, and the frequencies of the transitions induced by an acoustic pulse change accordingly. The self-consistent system of equations derived in this study without using the slowly varying envelope approximation describes pulse propagation at an arbitrary angle to the direction of the static strain. Exponentially and rationally decaying monopolar and breather-like solutions to the system are obtained. An analysis of the solutions reveals an asymmetry of the pulse polarity depending on the type of strain (extension or compression) and the pulse propagation direction. In particular, it is shown that acoustic transparency associated with monopolar strain pulses exhibits threshold behavior. The sign of the time area (zeroth harmonic) of breather-like strain pulses is such that the transition frequency averaged over an oscillation period dynamically decreases. This behavior determines the efficiency of generation of high-order harmonics of acoustic pulses in strained paramagnetic crystals.     

Optical and photocurrent spectroscopy with picosecond strain pulses

This paper gives an overview of optical experiments using picosecond strain pulses. The strain pulses, which propagate with the sound velocity, are incident on a semiconductor nanostructure and induce an ultrafast shift of the exciton resonance energy by an amount, that exceeds the spectral width of the corresponding optical transition. When the duration of the high-amplitude strain pulse is long enough compared with the coherence time of the optical resonance, modulation of the resonance takes place adiabatically and exciton energy can be accurately defined at each momentary position. If the coherence time exceeds the characteristic time of the strain pulse, a non-adiabatic regime is realized and the exciton cannot be related to an optical transition with a specific photon energy. In more detail, we describe the recent experiments on the gating of photocurrent in a tunneling p-i-n device and the generation of THz polariton sidebands in an optical microcavity strongly coupled to the excitons in an embedded quantum well. These two experiments represent, respectively, examples of adiabatic and non-adiabatic behaivior of excitons in the presence of the high-amplitude picosecond strain pulse.     

Effect of Brillouin slow light on distributed Brillouin fiber sensors

The effect of Brillouin slow light on distributed Brillouin fiber sensors (DBFSs) is studied. We demonstrate Brillouin slow light for a 1.2 ns pulse with peak powers (PS) from 3.3 to 56.2 mW on depletion of the pump power (PP) ranging from 1.3 to 83.2 mW in conventional optical fibers (SMF-28). Experiments show that, when pump power depletion is not negligible, for a given PP the Brillouin gain and delay time of a pulse decrease when PS increases in a long (> or =10 km) sensing fiber. The optimum pump beam depletion resulting from strong interaction of the pump and the probe in the fiber provides accurate temperature and strain information at a high spatial resolution. Our study reveals that at low PP the spatial resolution error caused by the pulse delay for a DBFS with centimeter spatial resolution is less than 5% of the pulse length.     

Large acoustic transients induced by nonthermal melting of InSb

We have observed large-amplitude strain waves following a rapid change in density of InSb due to nonthermal melting. The strain has been measured in real time via time-resolved x-ray diffraction, with a temporal resolution better than 2 ps. The change from the solid to liquid density of the surface layer launches a high-amplitude strain wave into the crystalline material below. This induces an effective plane rotation in the asymmetrically cut crystal leading to deflection of the diffracted beam. The uniform strain in the layer below the molten layer is 2.0(+/-0.2)%. A strain of this magnitude develops within 5 ps of the incident pulse showing that the liquid has reached the equilibrium density within this time frame. Both the strain amplitude and the depth of the strained material in the solid can be explained by assuming a reduction in the speed of sound in the nonequilibrium liquid compared to measured equilibrium values.     

Influence of laser repetition rate on ferroelectric properties of pulsed laser deposited BaTiO3 films on platinized silicon substrate

BaTiO₃ thin films were deposited by pulsed laser deposition on Pt–Si at different laser pulse repetition frequencies. X-ray diffraction spectra show that preferred oriented films can be grown by adjusting the pulse repetition frequency. Enhanced dielectric and ferroelectric properties obtained in films deposited at 1 Hz is attributed to preferred orientation, low strain and homogeneous grain distribution. The films deposited at 1 Hz show an impressive remanent polarization of 21.4 μC/cm² with a coercive field of 70.0 kV/cm. The shift in Curie temperature, which stems from changing the laser pulse repetition frequency, is associated with the strain state in the film.     

On the propagation of hypersonic solitons in a strained paramagnetic crystal

Nonlinear dynamics of a subnanosecond transverse elastic pulse in a low-temperature paramagnetic crystal placed into a magnetic field and statically strained in the same direction is investigated. Paramagnetic impurities implanted into the crystal have an effective spin of 3/2, and the pulse propagates at right angles to the magnetic field. In the general case, the structure of the pulse is such that the approximation of slowly varying envelopes, which is standard for quasi-monochromatic signals, is inapplicable. Under certain conditions, the pulse propagation in the 1D case is described by the Konno-Kameyama-Sanuki integrable wave equation for strain, which is transformed into the Hirota equation for the envelope of the given strain in the quasi-monochromatic limit. The effect of transverse perturbations on extremely short and quasi-monochromatic solitons is studied in detail. The conditions and features of self-focusing and defocusing of acoustic solitons in the form of extremely short pulses and envelope solitons are revealed. The propagation of an extremely short “half-wave” hypersonic pulse in the “acoustic bullet” regime in the medium with a quasiequilibrium population of quantum sublevels of effective spins is predicted.     

Soliton generation via continuous stokes acoustic self-scattering of hypersonic waves in a paramagnetic crystal

A new mechanism is proposed for continuous frequency down-conversion of acoustic waves propagating in a paramagnetic crystal at a low temperature in an applied magnetic field. A transverse hypersonic pulse generating a carrier-free longitudinal strain pulse via nonlinear effects is scattered by the generated pulse. This leads to a Stokes shift in the transverse hypersonic wave proportional to its intensity, and both pulses continue to propagate in the form of a mode-locked soliton. As the transverse-pulse frequency is Stokes shifted, its spectrum becomes narrower. This process can be effectively implemented only if the linear group velocity of the transverse hypersonic pulse equals the phase velocity of the longitudinal strain wave. These velocities are renormalized by spin-phonon coupling and can be made equal by adjusting the magnitude of the applied magnetic field. The transverse structure of the soliton depends on the sign of the group velocity dispersion of the transverse component. When the dispersion is positive, planar solitons can develop whose transverse component has a topological defect of dark vortex type and longitudinal component has a hole. In the opposite case, the formation of two-component acoustic “bullets” or vortices localized in all directions is possible.     

Transient response in high-resolution Brillouin-based distributed sensing using probe pulses shorter than the acoustic relaxation time

We perform numerical simulations on a model describing a Brillouin-based temperature and strain sensor, testing its response when it is probed with relatively short pulses. Experimental results were recently published [e.g., Opt. Lett. 24, 510 (1999)] that showed a broadening of the Brillouin loss curve when the probe pulse duration is reduced, followed by a sudden and rather surprising reduction of the linewidth when the pulse duration gets shorter than the acoustic relaxation time. Our study reveals the processes responsible for this behavior. We give a clear physical insight into the problem, allowing us to define the best experimental conditions required for one to take the advantage of this effect.     

超短脉冲激光辐照硅膜的热弹性

 考虑到热电子崩力的影响,在基于玻耳兹曼理论弛豫时间近似的非线性自相关模型基础上,将晶格温度与应变速率相耦合,建立了超短脉冲激光作用下半导体材料的超快热弹性模型。在单轴应变条件下,利用有限差分法模拟了500 fs脉冲激光作用下2 μm厚硅膜内的载流子温度、晶格温度、载流子数密度、热应力和热电子崩力等的变化情况。结果表明：在低能量密度激光条件下,热弹性效应对半导体材料的影响很小;载流子温度达到峰值的时间比激光强度达到峰值的时间早,随后载流子数密度达到峰值,以及激光脉冲作用5 ps以后硅膜趋于总体热平衡;在脉冲辐照早期,非热平衡阶段形成的热电子崩力在超快损伤过程中起主要作用。     

A combined harmonic phase and strain-encoded pulse sequence for measuring three-dimensional strain

Measurement of myocardial strain provides direct information about heart function that can be correlated with disease. We present an MRI pulse sequence that acquires in just six heartbeats both harmonic phase (HARP) and strain-encoded (SENC) images and provides dense measurements of radial, circumferential and longitudinal strains within a single short-axis slice. Normal volunteer data confirm the feasibility of this pulse sequence, and acquired data demonstrate the strain measurement reliability.     

Pulse propagation in an elastic medium with quadratic nonlinearity (L)

This letter examines the propagation of an acoustic pulse in an elastic medium with weak quadratic nonlinearity. Both a displacement pulse and a stress pulse of arbitrary shapes are used to generate the wave motion in the solid. By obtaining the explicit solutions for arbitrary pulse shapes, it is shown that for a sinusoidal tone-burst, in addition to a second order harmonic field, a radiation induced static strain field is also generated. These results help clarify some confusion in the recent literature regarding the shape of the propagating static displacement pulse.     

Generation and detection of acoustic solitons in crystalline slabs by laser ultrasonics

Acoustic solitons have been recently observed in different systems (Si, Sapphire, MgO, alpha-quartz). Such acoustic waves could lead to sub-picosecond acoustic pulses. In this paper, we report on the formation of acoustic solitons in a GaAs crystalline slab. A short picosecond acoustic pulse is generated by absorption of a femtosecond laser pulse in an aluminum thin film deposited on one side of the slab. This strain pulse travels through the sample up to the opposite side where it is detected by a time delayed laser pulse reflected by an aluminum transducer. We use interferometric detection to measure independently the real and imaginary parts of the relative change in optical reflectivity induced by the acoustic pulse. We find that, at low temperature and with a laser pump pulse energy of 10 nJ, an acoustic soliton clearly separates from the acoustic pulse in GaAs slab. The soliton shape is compared with numerical simulations for different excitation conditions. From the very unique properties of solitons, we infer a soliton pulse duration of about 2.3 ps which corresponds to a spatial extent of only 12 nm.     

Ni50.5Mn24.5G25单晶的预马氏体相变特性

通过交流磁化率、电阻、有无磁场下的预相变应变、磁致伸缩和磁化强度测量，系统研究了近正配分比Ni505Mn245Ga25单晶的预马氏体相变特性.在自由样品中观察到预马氏体相变应变.在预相变点，沿[010]方向施加大小约为80kA/m的磁场，在晶体母相的[001]方向上获得了高达505ppm的磁致伸缩，该值是相同条件下晶体母相磁致伸缩量的5倍多.同时，报道了不同方向磁场对预相变应变干预的结果.利用软模凝结的概念和依据单晶生长的特点，分析了预相变应变产生的机理.而磁场干预预相变应变的机理是磁场增大的磁弹耦合导致的晶格形变与材料内禀形变的竞争.利用磁性测量结果证实和解释了预相变过程中[001]和[010]轴方向间进一步增大的各向异性.进而对磁场沿[001]和[010]两个晶体学方向所导致的应变特性的差别，包括最大磁致伸缩、饱和预相变应变、饱和场等，进行了分析和讨论. 关键词： 预马氏体相变 应变 磁致伸缩 磁弹耦合     

Simple method to identify the spatial location better than the pulse length with high strain accuracy

The second-order partial derivative of the Stokes signal with respect to frequency and position shows a maximum or minimum at the boundary between two different strained sections. This idea is used to locate the boundary of different stress regions. Knowing the boundaries, we then fit the Brillouin spectrum at the middle between them to get the strain value. This allows a location accuracy of between 5 and 10 cm, which is shorter than the pulse length of 20 cm used in the experiment. The lowest detectable Brillouin frequency difference between two strain sections is 1.2 MHz.     

高应变率下TC4及TC9钛合金的动态断裂

 报导了由短脉冲激光引起的应力波加载及电炮驱动Mylar膜平面飞片碰撞TC4、TC9钛合金靶的实验及数值计算研究结果。由回收靶样品的金相分析表明：在电炮驱动飞片碰撞及由激光引起的应力波加载所造成的应变率分别在10⁶ s^-1左右及10⁷ s^-1以上两种情形下，TC4、TC9钛合金的层裂特性都是以微孔洞的成核、增长、汇合为特征的韧性断裂。运用一维流体弹塑性动力学程序进行数值研究表明：成核增长NAG模型在一定程度上可以用来描述高应变率下TC4、TC9钛合金的损伤破坏特性。