Capillary gas chromatographic determination of methylglyoxal from serum of diabetic patients by precolumn derivatization using meso-stilbenediamine as derivatizing reagent

Stilbenediamine is used as derivatizing reagent for methylglyoxal (MGo) and dimethylglyoxal for the gas chromatographic (GC) determination of MGo from the serum of diabetic patients and healthy volunteers. The derivatization is obtained at pH 3. GC elution and separation are carried out on an HP5 column (30 m x 0.32 mm i.d.) at column temperature 150 degrees C with a programmed heating rate of 50 degrees C/min up to 250 degrees C, and a total run time of 7 min. The nitrogen flow rate is 5 mL/min and detection is carried out by flame ionization detection. The linear calibration curves are obtained with a range of 0.076-0.760 microg/mL and the detection limit is 25 ng/mL MGo. The amounts of MGo found in the serum of healthy volunteers and diabetic patients are 0.025-0.065 microg/mL and 0.115-0.228 microg/mL, with coefficient of variation 1.3-3.1% and 1.4-3.3%.     

A novel capillary electrophoretic method for determining methylglyoxal and glyoxal in urine and water samples

Two non-electroactive biomarkers methylglyoxal (MGo) and glyoxal (Go) in urine and environmental water samples were determined for the first time by capillary electrophoresis with amperometric detection (CE-AD) after derivatizing with an electroactive compound 2-thiobarbituric acid. Experimental conditions of derivatization and CE-AD detection were optimized. Highly linear response was obtained for these two biomarkers over three orders of magnitude with good correlation (r² > 0.999). The limits of detection (LODs) and limits of quantitation (LOQs) of MGo and Go were 0.2 μg L⁻¹ and 1.0 μg L⁻¹, 0.5 μg L⁻¹ and 2.0 μg L⁻¹, respectively. The average recovery and relative standard deviation (RSD) were within the range of 90.9–101.3% and 0.7–2.2%, respectively. The proposed CE-AD method provides a reliable and sensitive quantitative evaluation of MGo and Go in real sample matrices by employing relatively simple and inexpensive instrument.     

Gas chromatographic determination of guanidino compounds in uremic patients using glyoxal as derivatizing reagent

The guanidino compounds guanidine, methylguanidine, guanidinoacetic acid, guanidinopropionic acid, guanidinobutyric acid and guanidinosuccinic acid were eluted and separated after pre-column derivatization with glyoxal from an HP-5 column (30 m × 0.32 mm i.d.) with film thickness 0.25 μm at an initial column temperature of 100 °C for 2 min, with ramping of 20°C/min up to 250 °C and a nitrogen flow rate of 3 mL/min. Detection was by flame ionization detection. Linear calibrations were observed within 0.1-20.0 μmol/L, with limit of detection within 0.024-0.034 μmol/L for each compound. The separation was repeatable with relative standard deviation (RSD) (n = 6) within 1.2-1.8 and 1.1-1.6% in terms of retention time and peak height/peak area, respectively. The method was applied for the determination of the guanidino compounds from serum of uremic patients (n = 7) and healthy volunteers (n = 8), and amounts were observed within 1.33-11.71 and 0.07-0.39 μmol/L with RSD 1.1-3.5 and 1.1-3.0%, respectively. The results were further supported by the standard addition method.     

Determination of pharmaceuticals in drinking water by CD-modified MEKC: separation optimization using experimental design

A suite of 12 widely used pharmaceuticals (ibuprofen, diclofenac, naproxen, bezafibrate, gemfibrozil, ofloxacin, norfloxacin, carbamazepine, primidone, sulphamethazine, sulphadimethoxine and sulphamethoxazole) commonly found in environmental waters were separated by highly sulphated CD-modified MEKC (CD-MEKC) with UV detection. An experimental design method, face-centred composite design, was employed to minimize run time without sacrificing resolution. Using an optimized BGE composed of 10 mM ammonium hydrogen phosphate, pH 11.5, 69 mM SDS, 6 mg/mL sulphated beta-CD and 8.5% v/v isopropanol, a separation voltage of 30 kV and a 48.5 cm x 50 microm id bare silica capillary at 30 degrees C allowed baseline separation of the 12 analytes in a total analysis time of 6.7 min. Instrument LODs in the low milligram per litre range were obtained, and when combined with offline preconcentration by SPE, LODs were between 4 and 30 microg/L.     

Determination of uranium, iron, copper, and nickel from ore samples by MEKC using N,N'-ethylene bis(salicylaldimine) as complexing reagent

An analytical procedure has been developed for the separation of dioxouranium(VI), iron(III), copper(II), nickel(II), cobalt(II), cobalt(III), palladium(II), and thorium(IV) by MEKC using N,N'-ethylene bis(salicylaldimine) (H(2)SA(2)en) as a complexing reagent with total runtime <4.5 min. SDS was used as micellar medium at pH 8 with sodium tetraborate buffer (0.1 M). An uncoated fused-silica capillary with an effective length of 50 cm x 75 microm id was used with an applied voltage of 30 kV with photodiode array detection at 231 nm. Linear calibrations were obtained within 0.111-1000 microg/mL of each element with LODs within 37-325 ng/mL. The developed method was tested for analysis of uranium ore samples indicating its presence within 103-1789 microg/g with RSD within 0.79-1.87%. Likewise copper, nickel, and iron in their combined matrix were also simultaneously determined with RSD 0.4-1.6% (n = 6).     

胶束毛细管电泳在线推扫富集技术测定工业废水中痕量苯酚和硝基苯酚

利用胶束毛细管电泳在线推扫富集技术建立了测定工业废水中痕量苯酚、邻硝基苯酚和间硝基苯酚的方法。采用未涂层熔硅弹性石英毛细管(60cm×75μm,有效柱长52cm),选择20mmoL/L硼-砂80mmoL/L十二烷基硫酸钠(SDS)(pH9.45)为缓冲溶液,分离电压18kV,紫外检测波长214nm,在200s内可实现苯酚、邻硝基苯酚、间硝基苯酚的分离检测。在优化条件下,苯酚、邻硝基苯酚、间硝基苯酚的检出限分别为0.03、0.020、.02mg/L;相对标准偏差RSD(n=3)分别为3.42%、4.15%、3.48%;间硝基苯酚富集倍数可达1000倍。     

Simultaneous determination of myo-inositol and scyllo-inositol by MEKC as a rapid monitoring tool for inositol levels

A simple and rapid MEKC method was developed for the simultaneous determination of myo-inositol, scyllo-inositol, and glucose. Prior to electrophoretic separation, the nonfluorescent inositols and glucose were derivatized by N-methylisatoic anhydride at 25 degrees C for 10 min so that they could be detected by a fluorescence detector during separation. The good separation with high efficiency by MEKC was achieved in 13 min with a glycine buffer containing SDS and PEG 4000. Several parameters affecting the separation were studied, including the pH of BGE, the concentrations of glycine, SDS, and PEG 4000, and the applied voltage. Using glycerol as an internal standard, the linear ranges of the method for myo-inositol, scyllo-inositol, and glucose were 0.03-10, 0.01-5, and 0.05-20 mM; the concentration LODs of myo-inositol, scyllo-inositol, and glucose were 0.020, 0.0078, and 0.026 mM, respectively. The method was applied to analyze extracellular myo-inositol and glucose in the microdialysates from rat brain cortex of ischemia animal model and intracellular myo-inositol and scyllo-inositol in the rat brain extract.     

MEKC Determination and Pharmacokinetic Study of Danshensu in Rabbits after Intragastric Administration of the Aqueous Extract from Danshen

A micelle eletrokinetic capillary chromatography (MEKC) method was used to determine Danshensu in rabbit blood plasma and tissues (liver, lung, kidney, brain, heart and spleen). The separation was achieved with a buffer consisting of 30 mmol L⁻¹ borax and 50 mmol L⁻¹ SDS (pH 9.0), and with an applied voltage of 7.0 kV. Validation of the method showed good sensitivity, reproducibility and precision. The calibration curve for Danshensu was linear over the concentration range of 0.4–400 μg mL⁻¹. The limit of detection (LOD) was 0.08 μg mL⁻¹ (S/N = 3). The validated method has been successfully applied for the pharmacokinetic and the tissue distribution studies of Danshensu after intragastric administration of the aqueous extract from traditional Chinese medicine Danshen.     

Determination of NTBC in serum samples from patients with hereditary tyrosinemia type I by capillary electrophoresis

Hereditary tyrosinemia type I is a serious metabolic disorder leading to liver failure. 2-(2-Nitro-4-trifluoromethylbenzoyl)-1,3-cyclohexanedione (NTBC) is a relatively new drug which is used to prevent the accumulation of toxic metabolites in patients with hereditary tyrosinemia type I. In the present study, we have developed a new, simple, fast, and cost-effective capillary electrophoresis method for the quantitative monitoring of this drug in serum samples. Micellar electrochromatographic separation of NTBC was performed using 20 mmol/L phosphate and 40 mmol/L sodium dodecylsulfate (SDS) at pH 12 as running electrolyte. Separation of NTBC was achieved in around 4 min. Reproducibilities of migration times and corrected peak areas of NTBC (as R.S.D.%) were found as 0.73 and 1.99, respectively. The detection limit was 3.17 and the quantification limit was 10.6 μmol/L for NTBC using UV detection at 278 nm. The utility of the method was demonstrated by the detection of NTBC in serum samples from patients with hereditary tyrosinemia type I using this drug.     

Determination of ketotifen by using calcein as chemiluminescence reagent

Chemiluminescence (CL) was observed when potassium hexacyanoferrate(III) reacted with the mixture of calcein and ketotifen. Interestingly, the CL intensity would be enhanced by trace amounts of Mg²⁺ and the CL intensity was strongly dependent on ketotifen concentration. Based on this phenomenon, a flow injection CL method was established for the determination of ketotifen. The possible CL mechanism is proposed based on the kinetic characteristic of the CL reaction, CL spectrum, ultraviolet (UV) spectra and fluorescent spectra. The CL intensity was correlated linearly with concentration of ketotifen over the range of 6.0 × 10⁻⁹ to 2.0 × 10⁻⁷ g mL⁻¹ and the detection limit was 3 × 10⁻⁹ g mL⁻¹. The relative standard deviation was 1.8% for 2.0 × 10⁻⁸ g mL⁻¹ ketotifen (n = 11). This method was applied to the determination of ketotifen in the tablets successfully.     

Determination of glyoxal and methylglyoxal in environmental and biological matrices by stir bar sorptive extraction with in-situ derivatization

Stir bar sorptive extraction with in-situ derivatization using 2,3-diaminonaphthalene (DAN) followed by liquid desorption and high performance liquid chromatography with diode array detection (SBSE(DAN)in-situ-LD-HPLC-DAD) was developed for the determination of glyoxal (Gly) and methylglyoxal (MGly) in environmental and biological matrices. DAN proved very good specificity as in-situ derivatising agent for Gly and MGly in aqueous media, allowing the formation of adducts with remarkable sensitivity, selectivity and the absence of photodegradation. Assays performed on spiked (1.0 microg L(-1)) water samples, under convenient experimental conditions, yielded recoveries of 96.2+/-7.9% for Gly and 96.1+/-6.4% for MGly. The analytical performance showed good accuracy, suitable precision (<12.0%), low detection limits (15 ng L(-1) for Gly and 25 ng L(-1) for MGly adducts) and excellent linear dynamic ranges (r2>0.99) from 0.1 to 120.0 microg L(-1). By using the standard addition method, the application of the present method to tap and swimming-pool water, beer, yeast cells suspension and urine samples allowed very good performance at the trace level. The proposed methodology proved to be a feasible alternative for routine quality control analysis, showing to be easy to implement, reliable, sensitive and with a low sample volume requirement to monitor Gly and MGly in environmental and biological matrices.     

MEKC determination of IgG in human serum via a pH‐mediated acid stacking method

An on‐column preconcentration technique, pH‐mediated acid stacking, was used in this study to improve the sensitivity of MEKC‐UV analysis of IgG in human serum. Various parameters affecting pH‐mediated acid stacking were optimized systematically. To eliminate the matrix interferences of human serum and to combine the sample pretreatment procedure with the detection methodology, silica‐coated Fe₃O₄ magnetic nanoparticles modified with N‐(2‐aminoethyl)‐3‐aminopropyl‐trimethoxysilane were prepared and employed as solid phase extraction adsorbent to remove the abundant HSA from human serum. HSA was quantitatively removed by silica‐coated Fe₃O₄ magnetic nanoparticles modified with N‐(2‐aminoethyl)‐3‐aminopropyl‐trimethoxysilanes without retaining IgG at pH 9.3. Under the optimum conditions, the sensitivity of IgG was improved 40.3‐fold using a 100 s electrokinetic injection as compared with a 6 s hydrodynamic injection. The detection limit of IgG was found to be 0.1 mg/L, and the proposed method was successfully applied for the determination of IgG in human serum with satisfactory results.     

Temperature dependent near-UV molar absorptivities of glyoxal and gluteraldehyde in aqueous solution

Molar absorptivities have been determined for glyoxal and gluteraldehyde in aqueous solution. Absorptivities are reported at eight temperatures in the range 5-70 degrees C for wavelengths greater than 200 nm. For glyoxal the data indicate did less than 0.02% of the glyoxal molecules exist in the free dialdehyde form, and that at 25 degrees C approximately 98% of the molecules are hydrated at both carbonyl groups, results that are consistent with previous experiments. For gluteraldehyde hydration of the two carbonyl groups occurs in an independent manner. The following thermodynamic data are found for gluteraldehyde hydration: deltaH = - 35.8+/-1.3 kJ mole(-1), deltaS = 103+/-7 J (mole K)(-1), and K = 7.5+/-2.0. The results for gluteraldehyde are compared with previous results obtained for the hydration of aliphatic aldehydes.     

Application of MEKC and monolithic CEC for the analysis of bioactive naphthoquinones in Eleutherine americana

Two microscale separation techniques for the analysis of bioactive naphthoquinones in Eleutherine americana were developed and validated. By MEKC four compounds (eleuthoside B, isoeleutherin, eleutherol and eleutherinoside A) could be determined in plant extracts using an aqueous electrolyte solution composed of 25 mM sodium tetraborate, 50 mM sodium cholate and 20% THF. CEC on a polymeric methacrylate‐based monolith with strong cationic properties showed promising results, as it additionally enabled the separation of two enantiomers, eleutherin and isoeleutherin. The mobile phase for CEC experiments comprised 3 mM ammonium formate in a mixture of ACN and water. At an applied voltage of ?25 kV, all five markers were baseline separated in less than 12 min. Both methods were successfully validated for linearity (MEKC: R²≥0.999; CEC: R²≥0.997), sensitivity (MEKC: LOD=4–5 μg/mL; CEC: LOD=2–8 μg/mL), accuracy (MEKC: 96.5–102.7% recovery; CEC: 97.1–103.5% recovery) and precision (MEKC: σ_rel≤2.43%; CEC: σ_rel≤2.21%). The quantitative analysis of naphthoquinone derivatives in several E. americana samples showed that both methods are suitable for practical applications, because the results were well comparable to those obtained by established techniques such as HPLC.     

Measurement of intracellular accumulation of anthracyclines in cancerous cells by direct injection of cell lysate in MEKC/LIF detection

Anthracyclines are chemotherapeutic drugs that are broadly used in the treatment of various types of solid cancers and leukemia. Herein, we report on a novel analytical method for intracellular accumulation of anthracyclines using MEKC/LIF detection. An aqueous separation system permitted the injection of cell lysates directly into the capillary. The MEKC migrating solution was made up of borate buffer at pH 9.22 containing sodium taurodeoxycholate, (2‐hydroxypropyl)‐γ‐CD, and SDS. The anthracyclines, Doxorubicin (DOX) and epirubicin (EPI) were detected by LIF using a Nd:YAG laser (532 nm) or an argon ion laser (488 nm) for excitation. Two cell lines, human humerus tumor cells (RDES) and human lung tumor cells (A549), were treated with a mixture of the two anthracyclines for fixed periods of time, and then intracellular concentrations were determined by injecting cell lysates directly. Recovery values of 96.0–100.8% were obtained for DOX and EPI. Reproducibility quantified by RSD was less than 3.9% intraday and 6.7% interday at concentrations ranging between 50 and 500 nM. The uptake of EPI was found to be slightly less than that of DOX for A549, but higher levels of EPI were observed in RDES. Intracellular accumulation of anthracyclines was greater in RDES than in A549, but both types of cells excreted anthracyclines after 12 h. These results indicate that MEKC with an aqueous medium is useful for investigating intracellular uptake and accumulation of drugs, since cell lysates can be used directly with no pretreatment such as deproteination or solvent extraction of analytes.     

In‐capillary microextraction using monolithic polymers: Application to preconcentration of carbamate pesticides prior to their separation by MEKC

In the present work we report a novel procedure for in‐capillary microextraction using a monolithic polymeric sorbent. In the proposed methodology, sample treatment takes place in the CE instrument but in a different capillary from that used for the electrophoretic separation. Polymers based on butyl methacrylate and divinylbenzene formed in situ inside a capillary column were assayed. The best results were found with the divinylbenzene‐based polymers. The usefulness of the proposed procedure was checked for the determination of carbamate pesticides (Methomyl, Asulam, Carbendazim, Aldicarb, Carbetamide, Propoxur, Pirimicarb, Carbaryl, Carbofuran and Methiocarb) and three of their degradation compounds (Aldicarb sulphoxide, 2‐isopropoxyphenol and α‐naphthol) using MEKC. The optimization of the MEKC is reported, a good separation of the 13 analytes being obtained in less than 6 min. The analytical method using in‐capillary microextraction was validated in terms of linearity, repeatability, precision (RSD≤18% for 50 μg/L), and LODs (1–16 μg/L), and it revealed the usefulness of this in‐capillary preconcentration procedure for the determination of analytes of intermediate polarity.     

2,4-二硝基苯肼衍生-高效液相色谱测定大气细粒子中二羰基类化合物

以2,4-二硝基苯肼作为衍生化试剂,采用高效液相色谱法定量检测了大气细粒子(PM2.5)中二羰基类化合物。以乙二醛和甲基乙二醛为目标化合物,对二羰基类化合物采样条件(采集时间,流速等)、样品处理及分析条件进行了优化。研究表明,利用3mL衍生化溶液(含0.25mmol/LHCl和30μL饱和DNPH-乙腈溶液)和3mL乙腈可有效提取滤膜上的二羰基类化合物;本方法在滤膜采样12h内的采样及洗脱效果较好。利用此方法对上海市宝山区上海大学和崇明东平国家森林公园大气细粒子(PM2.5)中二羰基化合物进行了检测。     

涂布2,4-二硝基苯肼的环形溶蚀器/滤膜系统和高效液相色谱法检测大气中二羰基化合物

建立了环形溶蚀器/滤膜系统(Annular denuder/filter pack system)和2,4-二硝基苯肼(DNPH)-高效液相色谱法(HPLC)采集和检测大气中气相和颗粒相二羰基化合物的方法。DNPH作为吸附剂分别涂布在环形溶蚀器的内壁和3层滤膜上,当大气样品经过环形溶蚀器时,含有气相二羰基化合物的气体吸附到环形溶蚀管内壁上与DN-PH发生反应,而颗粒相部分穿过环形溶蚀管,采集到滤膜上。样品经乙腈洗脱、浓缩后,采用HPLC进行分析。根据不同的采样流速、采样时间和DNPH的涂布量采集到的二羰基化合物的浓度,确定的最佳采样条件为:采样流速4 L/min,采样时间4~5 h,DNPH浓度0.47 g/L。使用Tedlar bag验证环形溶蚀器乙二醛和甲基乙二醛的采集效率(分别为82%和85%)。利用此方法对实际大气中的二羰基化合物进行了检测。     

多波长线性回归-矩阵法同时测定乙二醛、乙醛酸、草酸的含量

根据实验得出的乙二醛、乙醛酸、草酸三组分混合物中各组分在特定波长下呈现出的良好的线性关系,建立起三组分质量浓度与混合吸光度的回归方程组,形成了多波长线性回归-矩阵法,实现了乙二醛氧化制备乙醛酸体系中反应产物乙二醛、乙醛酸、草酸含量的同时测定.研究结果表明:当乙二醛检测下限为1.024 mg/L时,回收率为94%~98%...