Novel polystyrene‐supported zirconocene catalyst for olefin polymerization and its catalytic kinetics

Through the Diels–Alder reaction between cyclopentadiene groups attached to polystyrene in the presence of zirconocene, novel polystyrene‐supported metallocene catalysts were prepared. A novel method for immobilizing metallocene catalysts was investigated, and the resultant polystyrene‐supported metallocene for olefin polymerization was studied. The results of olefin polymerization showed that different crosslinking degrees of support in the catalyst system had significant effects on the catalytic behavior. The influence of the [Al]/[Zr] molar ratio and the temperature on the (co)polymerization activity was studied. When 1‐hexene and 1‐dodecene were used for copolymerization with ethylene, an obvious positive comonomer effect was observed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2650–2656, 2005     

Study of carbonaceous clusters in irradiated polycarbonate with UV–vis spectroscopy

The formation of carbonaceous clusters in ion‐irradiated polymer films was investigated extensively. Information about these clusters may be obtained with ultraviolet–visible (UV–vis) spectroscopy. The optical band gap (E_g), calculated from the absorption edge of the UV spectra of these polymers, can be correlated to the number of carbon atoms (N) in a cluster with the modified Tauc equation. The structure of the cluster is also related to E_g; for example, a six‐membered‐benzene‐ring‐type structure has an E_g of ≈5.3 eV, whereas a buckminsterfullerene‐type structure has an E_g of ≈4.9 eV. These clusters are responsible for the electrical conductivity in these films. In this work, polycarbonate films (20 μm thick) were irradiated with 45‐MeV Li ions at fluences of 1 × 10¹² to 1 × 10¹³ cm⁻² and were characterized with UV–vis spectroscopy and impedance measurements. The E_g values, calculated from the absorption edge in the 280–315‐nm region with the Tauc relation, varied from 4.39 to 4.35 eV for the pristine and various irradiated samples, respectively. The cluster size showed a range of 60–62 carbon atoms per cluster. The sheet conductivity (σ_dc) and loss (tan δ) values of 10⁻¹⁶ Ω⁻¹cm⁻¹ and 10⁻³ for the pristine sample changed to 10⁻¹⁵ Ω⁻¹cm⁻¹ and 10⁻², respectively, for the irradiated samples. This increase in the values of σ_dc and tan δ may be correlated to the increase in the size of the carbonaceous clusters. This study provides insight into the mechanism of electrical conductivity in irradiated polymers. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1589–1594, 2000     

Experimental and theoretical investigations of the structure of methylaluminoxane (MAO) cocatalysts for olefin polymerization

The structure of methylaluminoxane (MAO), used as a cocatalyst for olefin polymerization, has been investigated by Raman and in situ IR spectroscopy, polymerization experiments, and density functional calculations. From experimental results, a number of quantum chemical calculations, and bonding properties of related compounds, we have suggested a few Me₁₈Al₁₂O₉ cage structures, including a highly regular one with C_3h symmetry, which may serve as models for methylaluminoxane solutions. The cages themselves are rigid but may contain up to three bridging methyl groups on the cage surfaces that are labile and reactive. Bridging methyls were substituted with Cl atoms to form a compound otherwise similar to MAO. Chlorinated MAO is unable to activate a metallocene catalyst, even in the presence of trimethylaluminum (TMA), but allows subsequent activation by regular MAO. With bis(pentamethylcyclopentadienyl)zirconium dichloride, MAO and TMA seem to influence chain termination independently. Several findings previously poorly explained are rationalized with the new model, including the observed lack of reaction products with excess TMA. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3106–3127, 2000     

Use of diffusion‐ordered NMR spectroscopy and HPLC–UV–SPE–NMR to identify undeclared synthetic drugs in medicines illegally sold as phytotherapies

The informal (and/or illegal) e‐commerce of pharmaceutical formulations causes problems that governmental health agencies find hard to control, one of which concerns formulas sold as natural products. The purpose of this work was to explore the advantages and limitations of DOSY and HPLC–UV–SPE–NMR. These techniques were used to identify the components of a formula illegally marketed in Brazil as an herbal medicine possessing anti‐inflammatory and analgesic properties. DOSY was able to detect the major components present at higher concentrations. Complete characterization was achieved using HPLC–UV–SPE–NMR, and 1D and 2D NMR analyses enabled the identification of known synthetic drugs. These were ranitidine and a mixture of orphenadrine citrate, piroxicam, and dexamethasone, which are co‐formulated in a remedy called Rheumazim that is used to relieve severe pain, but it is prohibited in Brazil because of a lack of sufficient pharmacokinetic and pharmacodynamic information. Copyright © 2013 John Wiley & Sons, Ltd.     

Solvent‐tunable colors in imprinted helical structures on polymer template via multiple UV‐induced polymerization

A solvent tunable single‐layer polymer film with a multipitched photonic structure as a new photonic band gap material has been developed by imprinting the helical structures on polymer matrices through multiple photocrosslinking in an induced chiral nematic mesophase. Here, the polymer matrices themselves served as a chiral template, which exhibited Bragg reflections in the absence of both a chiral dopant and anisotropic materials because of the memory effects of the polymer network. Tuning of colors was achieved by making a refractive index contrast in the two periodic media of imprinted solid helical structure and the isotropic liquids that fill it. On incorporation of various isotropic liquids in the imprinted matrices, a sharp peak in the reflection spectrum shifted drastically, which indicated that the wavelength shifts strongly depended on the sort of liquids that filled the matrices. The effects of temperature on the imprinted polymer template feeding the various liquids were studied through the reflectance spectra. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Ethyl‐iso‐butylaluminoxane activated metallocene catalyst for olefin polymerization

Ethylene and propylene were polymerized by different combinations of metallocenes and aluminoxanes. Ethyl‐iso‐butylaluminoxane (EBAO), which could be easily obtained by direct hydrolysis of Et₃Al/iso‐Bu₃Al in toluene with water, displayed as good polymerization activity as methylaluminoxane when it was paired with some metallocenes. The UV–visible spectroscopic study on different metallocene/aluminoxane pairs suggests that tightness of the ionic pairs generated from the reaction between metallocene and aluminoxane is different for a fixed metallocenium. The loose ionic pair derived from EBAO prefers the monomer propagation and hinders the interaction between active species, which results in high catalytic activity and molecular weight. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 998–1003, 2003     

Precise control of microstructure of functionalized polypropylene synthesized by the ansa‐zirconocene/ MAO catalysts

We inclusively investigated polymerization behavior and structure of copolymer in the copolymerization of propylene and alkylaluminum‐protected polar allyl monomers. The control of the arrangement of polar group in the copolymer was discussed. It was proved that the location of polar group could be controlled by zirconocene catalyst and a kind of polar monomer. The indenyl or the 2‐methylindenyl ligands of zirconocene were favored to produce end‐functionalized polymers. It was also found that the trimethylaluminum‐protected allylamine and triisobutylaluminum‐protected allylmercaptan had superior ability in the synthesis of end‐functionalized polypropylene. On the other hand, the 2‐methyl‐4‐phenylindenyl ligand produced the copolymers containing both the end‐polar unit and inner‐polar unit at the polymer chains. Terpolymerization of propylene, polar allyl monomer, and 5‐hexen‐1‐ol was also conducted. The NMR study of the terpolymer revealed that both the 5‐hexen‐1‐ol and the polar allyl monomer were incorporated into the polymer chain. It has also become apparent that the polar allyl monomer units predominantly occupied the chain end, while the 5‐hexen‐1‐ol units were located at the inner of main chain. Consequently, we have achieved the synthesis of functionalized polypropylene in which the arrangement of polar group was precisely controlled. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1738–1748, 2008     

Melting behavior of polyethylene/α‐olefin copolymers: Narrow composition distribution copolymers and fractions from Ziegler–Natta and single‐site catalyst products

The melting temperature and heat of fusion were measured for an extensive series of compositionally uniform copolymers of ethylene with butene‐1, hexene‐1, and octene‐1. Fractions and whole polymers that exhibited minimal interchain compositional heterogeneity were from commercial copolymers made with either Ziegler–Natta (ZN) or single‐site metallocene catalysts. The present results do not support recent claims that ZN and corresponding metallocene catalyst copolymers melt at significantly different temperatures, nor the implication that comonomer incorporation is “blocky” in ZN copolymers. In five of the six comonomer/catalyst systems the dependencies of the melting temperature on comonomer type and amount were scarcely distinguishable. This common behavior is the same as that for a model random copolymer, so we conclude that most ethylene/α‐olefin copolymers have random distributions of ethylene sequences. The exception in the present study is a metallocene ethylene/butene‐1 copolymer that melts at lower temperatures and apparently has perceptibly alternating sequence distributions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3416–3427, 2004     

The “comonomer effect” in ethylene/α‐olefin copolymerization using homogeneous and silica‐supported Cp2ZrCl2/MAO catalyst systems: Some insights from the kinetics of polymerization,active center studies,and polymerization temperature

Homogeneous and silica‐supported Cp₂ZrCl₂/methylaluminoxane (MAO) catalyst systems have been used for the copolymerization of ethylene with 1‐butene, 1‐hexene, 4‐methylpentene‐1 (4‐MP‐1), and 1‐octene in order to compare the “comonomer effect” obtained with a homogeneous metallocene‐based catalyst system with that obtained using a heterogenized form of the same metallocene‐based catalyst system. The results obtained indicated that at 70 °C there was general rate depression with the homogeneous catalyst system whereas rate enhancement occurred in all copolymerizations carried out with the silica‐supported catalyst system. Rate enhancement was observed for both the homogeneous and the silica‐supported catalyst systems when ethylene/4‐MP‐1 copolymerization was carried out at 50 °C. Active center studies during ethylene/4‐MP‐1 copolymerization indicated that the rate depression during copolymerization using the homogeneous catalyst system at 70 °C was due to a reduction in the active center concentration. However, the increase in polymerization rate when the silica‐supported catalyst system was used at the same temperature resulted from an increase in the propagation rate coefficient. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 267–277, 2008     

Zirconium‐chelate and mono‐η‐ cyclopentadienyl zirconium‐chelate/ methylalumoxane systems as soluble Ziegler–Natta olefin polymerization catalysts

Zirconium‐chelate and mono‐η‐cyclopentadienyl zirconium‐chelate complexes were tested as ethene and propene polymerization catalysts in combination with methylalumoxane (MAO) as a co‐catalyst: in particular (acac) _nZrCl_4−n (1a–c) (acac = acetylacetonato), (dbm) _nZrCl_4−n (2a–2c) (dbm = dibenzoylmethanato = 1,3‐diphenylpropanedionato) (n = 2–4) and (dbm)₂ZrCl₂(thf) (3) (thf = tetrahydrofuran), (η‐C₅H₅)[H₂B (C₃H₃N₂)₂]ZrCl₂ (4), (η‐C₅H₅)[HB (C₃H₃N₂)₃] ZrCl₂ (5) and (η‐C₅H₅)[(Me₃SiN)₂ CPh]ZrCl₂ (6). Polymerization productivities comparable with the (η‐C₅H₅)₂ZrCl₂ reference system were observed towards ethene for all of the above complexes. In addition, compound 6 showed some minor polymerization activity towards propene. Ethylalumoxane or isobutylalumoxane did not exhibit a co‐catalytic activity for these chelate complexes; in combination with MAO these higher alumoxanes were even found to be deactivating ⁹¹Zr NMR data are reported for 1b, 1c, 4 and 5. Copyright © 2000 John Wiley & Sons, Ltd.     

Solute–solvent interactions of acid–1,4-dioxane mixtures—By dielectric, FTIR, UV–vis and 13C NMR spectrometric methods

Results of the dielectric studies carried out on the binary mixture of n-butyric and caprylic acids with 1,4-dioxane over the entire composition range and at temperatures 303 K, 308 K, 313 K and 318 K, and FTIR, UV–vis and 13C NMR spectral studies are presented in this paper. The excess permittivity and excess free energy were fitted with the Redlich–Kister polynomial. The variation of Kirkwood correlation factors, excess permittivity and excess free energy of mixing with the concentration and temperature has been investigated in view of understanding the ordering of dipoles of solute and solvent molecules. The FTIR, UV–vis and 13C NMR spectral analysis reveals the formation of complex between solute and solvent molecules. The parallel alignment of electric dipoles of the complex predicted by dielectric studies is well supported by UV–vis spectral analysis. The structure of the complex molecule present in the clusters has been deduced.     

Synthesis of double silylene‐bridged binuclear zirconium complexes and their use as catalysts for olefin polymerization

New double silylene‐bridged binuclear zirconium complexes [(η⁵‐RC₅H₄)ZrCl₂]₂[μ,μ‐(SiMe₂)₂(η⁵‐C₅H₃)₂] [R = H ( 1 ), Me ( 2 ), ⁿPr ( 3 ), ⁱPr ( 4 ), ⁿBu ( 5 ), allyl ( 6 ), 3‐butenyl ( 7 ), benzyl ( 8 ), PhCH₂CH₂ ( 9 ), MeOCH₂CH₂ ( 10 )] were synthesized by the reaction of (η⁵‐RC₅H₄)ZrCl₃·DME with [μ,μ‐(SiMe₂)₂(η⁵‐C₅H₃)₂]^2? ( L^2? ) in THF, and they were all well characterized by ¹H NMR, MS, IR, and EA. The binuclear structure of Complex 3 was further confirmed by X‐ray diffraction, where the two zirconium centers are located trans relative to the bridging [μ,μ‐(SiMe₂)₂(η⁵‐C₅H₃)₂] moiety. When activated with methylaluminoxane (MAO), this series of zirconium complexes are highly active catalysts for the polymerization of ethylene even under very low molar ratio of Al/Zr (Complex 7 , 5.41 × 10⁵ g‐PE/mol‐Zr·h, Al/Zr = 50) and linear polyethylenes (PEs) with broad molecular weight distribution (MWD, M_w/M_n = 7.31–27.6) was obtained. The copolymerization experiments indicate that these complexes are also very efficient in the incorporation of 1‐hexene into the growing PE chain in the presence of MAO (Complex 6 , 3.59 × 10⁶ g‐PE/mol‐Zr·h; 1‐hexene content, 3.65%). © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4901–4913, 2007     

Ethylene polymerization by novel 4,4′-bis(methylene)biphenylene bridged homodinuclear titanocene and zirconocene combined with MAO

4,4′-Bis(methylene)biphenylene bridged homodinuclear titanocene (3) and zirconocene (4) have been synthesized by treatment of CpTiCl₃ and CpZrCl₃ · DME with Na₂[C₅H₄CH₂C₆H₄-p-C₆H₄CH₂C₅H₄], respectively, in THF and characterized by ¹H NMR and element analysis. After activation with methyl aluminoxane (MAO), these catalysts were used for the homogeneous polymerization of ethylene. The influences of reaction conditions, such as temperature, time, catalyst concentration and molar ratio of MAO/Cat. on ethylene polymerization were investigated in detail. The catalytic activities of 3 and 4 are more than three times higher than that of the phenyldimethylene bridged homodinuclear metallocene of titanocene (5) and zirconocene (6), respectively, and also twice higher than that of Cp₂TiCl₂/MAO and Cp₂ZrCl₂/MAO, respectively. However, the catalytic activity of 3 is nearly half as high as that of 4, which reached 1.31 × 10⁶ g PE/mol cat h. The molecular weight of polyethylene increases simultaneously with prolongation of polymerization time. GPC spectra show that 3 and 4 produce polyethylene with broad molecular weight distribution (4.28 and 3.18). The high melting points of the products (131-134 °C) indicate that the polyethylene formed is highly linear and highly crystalline.     

Combination of in situ UV–Vis-NIR spectro-electrochemical and a.c. impedance measurements: A new, effective technique for studying the redox transformation of conducting electroactive materials

Simultaneous in situ UV–Vis-NIR spectro-electrochemical and a.c. impedance techniques have been realized for the first time. Combination of the data obtained by these parallel, independent methods can be exploited in the future in the elucidation of the redox mechanism of various transparent electroactive layers.     

Aromatic C–H bond activation revealed by infrared multiphoton dissociation spectroscopy

Metal‐oxide cations are models of catalyst mediating the C–H bond activation of organic substrates. One of the most powerful reagents suggested in the gas phase is based on CuO⁺. Here, we describe the activation of the aromatic C–H bonds of phenanthroline in its complex with CuO⁺. The reaction sequence starts with a hydrogen atom abstraction by the oxygen atom from the 2‐position of the phenanthroline ring, followed by OH migration to the ring. Using infrared multiphoton spectroscopy, it is shown that the reaction can be energetically facilitated by additional coordination of a water ligand to the copper ion. As the reaction is intramolecular, a spectroscopic characterization of the product is mandatory in order to unambiguously address the reaction mechanism. Copyright © 2012 John Wiley & Sons, Ltd.     

Methylaluminoxane‐free ethylene polymerization with in situ activated zirconocene triisobutylaluminum catalysts and silica‐supported stabilized borate cocatalysts

Heterogenization of tris(pentafluorophenyl)borane [B(C₆F₅)₃] on a silica support stabilized with chlorotriphenylmethane (CICPh₃) and N,N‐dimethylaniline (HNMe₂Ph) creates the following supported borane cocatalysts: [HNMe₂Ph]⁺[B(C₆F₅)₃‐SiO₂]^? and [CPh₃]⁺[B(C₆F₅)₃‐SiO₂]^?. These supported catalysts were reacted with Cp₂ZrCl₂ TIBA in situ to generate active metallocene species in the reactor. Triisobutylaluminum (TIBA) was a good coactivator for dichloro‐zirconocene, acting as the prealkylating agent to generate cationic zirconocene (Cp₂ZrC₄H₉⁺). The catalytic performances were determined from the kinetics of ethylene‐consumption profiles that were independent of the time dedicated to the activation of the catalysts. The scanning electron microscopy‐energy dispersive X‐ray measurements showed that B(C₆F₅)₃ dispersed uniformly on the silica support. Under our reaction conditions, the [CPh₃]⁺[B(C₆F₅)₃‐SiO₂]^? system had higher productivity and weight‐average molecular weight than the [HNMe₂Ph]⁺[B(C₆F₅)₃‐SiO₂]^? system. For the [CPh₃]⁺[B(C₆F₅)₃‐SiO₂]^? system, the productivity increased with the amount catalyst; however, the polydispersity index of polyethylene synthesized did not change. The final shape of polymer particles was a larger‐diameter version of the original support particle. The polymer particles synthesized with supported [CPh₃]⁺[B(C₆F₅)₃‐SiO₂]^? catalysts had larger diameters. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3240–3248, 2002     

Synthesis of poly(1‐chloro‐2‐arylacetylene)s with high cis‐content and examination of their absorption/emission properties

A series of 1‐chloro‐2‐arylacetylenes [Cl‐C?C‐Ar, Ar = C₆H₅ ( 1 ), C₆H₄‐p‐i Pr ( 2 ), C₆H₄‐p‐Oi Pr ( 3 ), C₆H₄‐p‐NHC(O)Ot Bu ( 4 ), and C₆H₄‐o‐i Pr ( 5 )] were polymerized using (tBu₃P)PdMeCl/silver trifluoromethanesulfonate (AgOTf) and MoCl₅/SnBu₄ catalysts. The corresponding polymers [poly( 1 )–poly( 5 )] with weight‐average molecular weights of 6,500–690,000 were obtained in 10–91% yields. THF‐insoluble parts, presumably high‐molecular weight polymers, were formed together with THF‐soluble polymers by the Pd‐catalyzed polymerization. The Pd catalyst polymerized nonpolar monomers 1 and 2 to give the polymers in yields lower than the Mo catalyst, while the Pd catalyst polymerized polar monomers 3 and 4 to give the corresponding polymers in higher yields. The ¹H NMR and UV–vis absorption spectra of the polymers indicated that the cis‐contents of the Pd‐based polymers were higher than those of the Mo‐based polymers, and the conjugation length of the Pd‐based polymers was shorter than that of the Mo‐based polymers. Pd‐based poly( 5 ) emitted fluorescence most strongly among poly( 1 )–poly( 5 ). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 382–388     

Kinetics and mechanism of metallocene‐catalyzed olefin polymerization: Comparison of ethylene,propylene homopolymerizations,and their copolymerization

A series of ethylene, propylene homopolymerizations, and ethylene/propylene copolymerization catalyzed with rac‐Et(Ind)₂ZrCl₂/modified methylaluminoxane (MMAO) were conducted under the same conditions for different duration ranging from 2.5 to 30 min, and quenched with 2‐thiophenecarbonyl chloride to label a 2‐thiophenecarbonyl on each propagation chain end. The change of active center ratio ([C^*]/[Zr]) with polymerization time in each polymerization system was determined. Changes of polymerization rate, molecular weight, isotacticity (for propylene homopolymerization) and copolymer composition with time were also studied. [C^*]/[Zr] strongly depended on type of monomer, with the propylene homopolymerization system presented much lower [C^*]/[Zr] (ca. 25%) than the ethylene homopolymerization and ethylene–propylene copolymerization systems. In the copolymerization system, [C^*]/[Zr] increased continuously in the reaction process until a maximum value of 98.7% was reached, which was much higher than the maximum [C^*]/[Zr] of ethylene homopolymerization (ca. 70%). The chain propagation rate constant (k_p) of propylene polymerization is very close to that of ethylene polymerization, but the propylene insertion rate constant is much smaller than the ethylene insertion rate constant in the copolymerization system, meaning that the active centers in the homopolymerization system are different from those in the copolymerization system. Ethylene insertion rate constant in the copolymerization system was much higher than that in the ethylene homopolymerization in the first 10 min of reaction. A mechanistic model was proposed to explain the observed activation of ethylene polymerization by propylene addition. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 867–875     

Measurement of the solubility of metal complexes in supercritical carbon dioxide using a UV–vis spectrometer

A new apparatus based on the circulation method was developed to measure the solubility of metal complexes in supercritical carbon dioxide (scCO₂) at a wide range of temperatures and pressures. A UV–vis spectrometer, which was connected to a small saturation cell through optical fibers, was used to determine solubility. The solubilities of cobalt(III) acetylacetonate (Co(acac)₃) and chromium(III) acetylacetonate (Cr(acac)₃) in scCO₂ were measured to check the validity of both the apparatus and the method and to accumulate new solubility data. The solubility data for Cr(acac)₃ obtained in this study were in good agreement with the data reported in the literature.The measured solubilities of Co(acac)₃ and Cr(acac)₃ were also correlated with the empirical equation including the three adjustable parameters, based on the equation proposed by Chrastil. The parameters were determined by fitting the equation to the experimental data for each metal complex and the calculated results closely replicated the experimental data.     

Olefin polymerization with Me4Cp–Amido complexes with electron‐withdrawing groups

A series of Me₄Cp–amido complexes {[η⁵:η¹‐(Me₄C₅)SiMe₂NR]TiCl₂; R = t‐Bu, 1 ; C₆H₅, 2 ; C₆F₅, 3 ; SO₂Ph, 4 ; or SO₂Me, 5 } were prepared and investigated for olefin polymerization in the presence of methylaluminoxane (MAO). X‐ray crystallography of complexes 3 and 4 revealed very long Ti N bonds relative to the bonds of 1 . These complexes were employed for ethylene–styrene copolymerizations, styrene homopolymerizations, and propylene homopolymerizations in the presence of MAO. The productivities of the catalysts derived from 3 – 5 were much lower than the productivity of the catalyst derived from 1 for the propylene polymerizations and ethylene–styrene copolymerizations, whereas the styrene polymerization activities were much higher for the catalysts derived from 3 – 5 than for the catalyst derived from 1 . The polymerization behavior of the catalysts derived from the metallocenes 3 – 5 were more reminiscent of monocyclopentadienyl titanocene Cp′TiX₃/MAO catalysts than of CpATiX₂/MAO catalysts such as 1 containing alkylamido ligands. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4649–4660, 2000